Search Documents

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

By Neill A. O, Worth I, O&apos

The formation of Kalgoorlie Consolidated Gold \lincs 1't% Ltd hati pla,xd all the major the gold producing areas adjacent to the city of Kalgoorlie/Boulder under one management, enabling the development of the 'Super Pit'. This has facilitated the economic optimisation of the resource. Optimisation has been achieved by the timely collection and presentation of data and the use of these data to reduce costs and improve planning procedures.In particular the following issues have been addressed:ò the reduction of the impact of the mining activity on the adjacent urban population centre,ò implementation of safety procedures for mining through underground voids,ò the determination of the optimum bench height and mining method for ore production benches and blast design. This system is fundamentally based on maintaining a high degree of selectivity while achieving a balance of relatively low unit operating costs,ò assessment of the comparable benefits of contractor versus owner operated earth moving equipment, andò the development of effective ore body models, production reconciliation and the long term mine planning procedures to facilitate effective strategic planning.

Jan 1, 1993

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

There is a Chinese saying-may you live in interesting times. Certainly we do tod.a~our mining professions. We are, of course, totally dependent on a' healthy mining industry for the chance to practice our chosen professions, and for our Institute.Let us look at one of the more interesting facts. The mining industry now accounts for some 50 per cent of Australia's exports.This massive earning of foreign exchange is the key to keeping our increasing overseas debt in check. Furthermore, mineral production..including petroleum, saves us a large amount of foreign currency by providing essential minerals, including energy minerals, for local consumption.With such fundamental inputs to our economy, any primary school student, any child in fact, should be able to see that the mining industry and mining professions are very important to our nation. Yet the average citizen is unaware of this simple fact as they enjoy their high standard'of living and think that we are still living in the lucky country.Therefore, it is most interesting to me that the average citizen, and most of our politicians, seem to hold mining and miners in low esteem. I use the term miners to describe all those important people, like us, who work in the mining professions, and are employed by, or are dependent on, the mining industry.So why are we miners in this paradoxical situation of doing wonderful works, being the backbone of the country, and yet being held in low regard by the very community we underwrite.Truly-it is interesting-or did the Chinese mean intriguing?It is indeed paradoxical that we are the rare people who open up the land, borrow small parts of it for a relatively short time to harvest the mineral crops, then return it to the community for other uses; and when we return the land back to the community at large it should be in better shape than when we started. There will be infrastructure - roads, airstrips, supplies of water and power, parks and housing-all left behind after mining.These benefits to the community are ignored while our critics focus on the small scars on the landscape which sometimes cannot be healed at reasonable cost; and yet, if we allow time, nature usually heals the small scars anyway. Look at New Zealand, particularly the Coromandel Peninsula which was intensively mined and logged; now it is covered with secondary growth and stark pine plantations. Remember that mining scars are infinitesimally small when compared to urban sprawl or clearing of land for farming and grazing, or highways, or the area of most national parks.Thus, miners are important citizens economically, and we are the majority of the few who actually practice the principles of multiple land use.What are the consequences of our image? They are serious in that the poor image we seem to project, discourages many people from becoming involved in, or supportive of, our industry. This brings me to my theme for the year: Students, Education and Communication - the Key to our Future.

Jan 1, 1987

Froth flotation is widely used for the separation of particulate materials in the world. It is a complex process whose operational behaviour in process plants is difficult to predict. A comprehensive phenomenological dynamic flotation model was presented at the 1982 IMPC. This model uniquely linked the particle/bubble interactions and water transport phenomena to the flotation cell hydrodynamics. The model was used as a dynamic framework to analyse and develop process optimisation strategies. New developments in mineralogical characterisation, real time information management systems and data validation simplify the implementation of flotation technologies for mine to mill grade recovery optimisation. With recent developments in software programming, dynamic simulation enables process engineers to develop process alternatives interactively. This paper presents such an implementation of current process analysis tools and an updated froth flotation dynamic model. It demonstrates how this new environment can be used to improve our technological knowledge of flotation, eg alternative bubble/particle attachment and detachment microprocesses can be incorporated. The dynamic flotation model has several manipulated variables (such as feed flow rate, per cent solids, aeration, wash water flow rate, frother flow rate, specific power energy (impeller speed/delta pressure), cell geometry and tails flow rate) and evaluates the dynamic effects of these variables on grade and recovery.

Jan 1, 2005

By A Riles

"Three issues of relevance in a modern tailings storage facility (TSF) are:geotechnical stabilitymanaging acid rock drainage (ARD) from pyritic tailingsmanaging the tailings from cyanidation of gold ores. Drawing on examples from both copper porphyry flotation and sulfide-hosted gold ores, this paper demonstrates that giving some weight and importance to the process tails properties upfront can influence the flow sheet and not only improve tailings management effectiveness but also impact positively on economics. In the case of a typical copper porphyry ore with moderate pyrite content, the rougher tail in a conventional high pH selective flotation step is usually classified as potentially acid generating (PAG). To avoid the generation of ARD within the tailings and the requirement for a costly plastic lining, subaqueous deposition is recommended, which in turn has negative implications for tailings stability, consolidation and closure. Adopting a neutral pH rougher stage rejects silicate gangue but recovers pyritic material to the cleaners for a subsequent selective flotation stage, often after regrinding. This effectively quarantines the PAG pyritic material in a much lower volume cleaner tail, which can then be appropriately encapsulated within a larger non-lined flotation tails facility. It also facilitates cyanide leaching of the cleaner tail for gold recovery, with the encapsulated tailings facility being suitable for cyanidation tails storage. A case study from Europe is examined. For gold ores where the gold is sulfide-hosted, but not refractory, a flotation route with cyanidation of the concentrate can similarly produce the majority of tailings as a benign flotation tail and again quarantine the low volume concentrate leach tail in a small encapsulated cell with appropriate residual cyanide management measures applied. Overall economics for intensive leaching of a low volume concentrate stream can also be surprisingly positive. A feasibility study design example of the process and TSF is presented. CITATION: Riles, A, 2016. An Integrated Approach to Optimising All Concentrator Products, Including Tailings, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 341–346 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D J. Brake

Faced with the need to improve workplace conditions in both its development and production headings in its existing K1 orebody, as well as its new K Link and K2 orebodies, the Kencana mine in Indonesia took the novel approach of reversing the ventilation on most of its access ramp by outcasting up the ramp to the portal. Working levels were then fed with fresh air via auxiliary fans sealed into the current surface ‘egress’ intake raises (ladderways) or another small surface intake raisebore rather than from fans hung in the ramp as in the past. Outcasting the portal provided a substantial increase in the total mine exhaust capacity allowing fewer levels to be ventilated in series and significantly improving conditions, especially in the most difficult workplaces to ventilate. It also reduced the consequences if there was to be a fire on a vehicle in the ramp. The same system using the ramp as an exhaust is also intended to be used as part of the final ventilation solution for the new K2 orebody which also uses a novel single surface ventilation shaft that is vertically split into separate intake and exhaust compartments using a concrete brattice. Using the main ramp as an exhaust has potential application in many other operations in Australia using surface ramps which otherwise frequently suffer from overuse of series ventilation circuits and poor working conditions at the mine bottom.

Mar 21, 2011

By K Eglinton

The extractive industries response to community engagement due to social and political pressures in the 1980s and 1990s was the starting point of development leading to the modern function of corporate social responsibility.Challenged by communities who have greater access to information, demand greater transparency and responsibility of corporate organisations and who possess greater awareness of the communities they participate in, the mining sector faces another step change in how it approaches and integrates corporate social responsibility, transparency and engagement.Mining is seeking reserves of lower grades, in more sensitive environments and in countries with minimal transparency and governance. Not only are the locations changing but so to the stakeholders to engage with and issues to contend with. An increasingly savvy opposition, including not just the ‘green hippies’ but the Gen-Ys interested in the wider sustainability debate and Baby Boomers moving to life style environments, are now questioning mining’s behaviour and encroachment into ‘their space’. Issues including effect on lifestyle amenity, property value, energy efficiency, social provision; concepts such as ‘doing more with less’, participatory engagement, increasing transparency and balancing economic, environment, cultural and social aspects are becoming the norm.The traditional model of supporting local communities, communicating plans and providing employment, community investment and indigenous support programs is not enough. Our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities and play a role in addressing the global sustainability issues.This paper draws on corporate social responsibility trends, integrated functions and implementation approaches through the application of activities within Newmont operations across Asia Pacific.The approach presented works on the philosophy that communities do not necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Nov 22, 2011

By D J Maconochie

The use of rock bolts as permanent support has been prohibited by client specifications in several recent large tunnel projects in Australia. The justification for this appears to lie in concerns with proper and verifiable installation procedures rather than concerns with the intrinsic durability of the corrosion protection systems. However, in civil tunnels, preventing the use of permanent rock bolts for long-term support results in the use of cast in place concrete lining which in some instances would otherwise be unnecessary.

Mar 8, 2011

By C Artica

Two quantitative methods for Mineral Resource classification have been applied to a copper skarn deposit beneath a large open pit that is mining a world-class porphyry complex. A drill hole spacing study (DHSS) using the single block kriging method (SBK) and a conditional simulation method (CS) were applied to the skarn deposit and the results compared. Inputs to both processes included the proposed mining rate and stope designs to estimate the likelihood of achieving grade and metal production targets. Mineral Resource classification of the deposit considers the relative precision of tons, grade and metal predictions over quarterly and annual production periods. These relative precision estimates are calculated at 90 per cent confidence interval (CI). The SBK method represented the production period as a single large block. Kriging estimates were performed in the large block for various synthetic drill hole grids, and the estimation errors derived. The error was assumed to be normally distributed due to the large block size and quantity of samples, allowing CIs to be deduced. The CS method followed a conventional sequential Gaussian simulation workflow where grades were simulated with a 5 ft × 5 ft × 5 ft grid node spacing inside mineralisation domains. Each realisation was then averaged up to monthly production volumes represented by a combination of designed stopes, and the coefficient of variation (CV) for the averaged grade was calculated. CI on the relative precision of grade predictions were then deduced from the CVs. The two methods produced similar results; despite being calculated independently. CS results were used to report uncertainty in the proposed life-of-mine plan and highlight areas for additional drilling. SBK results were used as the basis for Mineral Resource classification as this method has been previously applied to the skarn deposit.

May 24, 2023

By R Peiffer, L van Wyk

The Port of Port Hedland is the largest bulk export terminal in the world and is one of Australia’s most important pieces of economic infrastructure. BHP is the largest Port user to support the export of iron ore products from mines located within the Pilbara region of Western Australia (WA). BHP’s priority is the safety and well-being of its workforce and the communities where it operates. In a recent regulatory application to increase export capacity, BHP committed to the deployment of wind fences to reduce wind erosion from stockpiled ore. Wind erosion from stockpiles was identified through inverse modelling as the most significant dust source compared to other sources such as stackers, reclaimers, shiploaders and transfer stations. The primary cause of dust emissions from stockpiles is dust lift-off during high wind conditions. BHP proposed the installation of wind fences across its Port Hedland operations, targeted at reducing emissions from wind dependent sources, primarily stockpiles, by reducing the wind speed downwind of the wind fence. Modelling predicts that installation of the wind fence will significantly reduce emissions from stockpiles, particularly at BHP’s western operations (Finucane Island). To be effective in shielding stockyards and reducing wind speeds, the wind fences are located upwind and as close as practical to the open stockyards. BHP’s wind fence design incorporates learnings from other existing installations and has been tailored for Port Hedland’s cyclonic conditions. The wind fence will be higher than the stockpile height, with a mesh porosity of approximately 50 per cent. The mesh porosity allows some of the wind to pass through the mesh. This reduces the wind turbulence downstream of the wind fence, as opposed to a solid wind fence, which increases downwind turbulence, resulting in increased dust.

Sep 18, 2023

By J W. Glatthaar, M Mavotoi

The occurrence of fluorine in the copper/gold concentrates produced by Ok Tedi Mining Limited has provided a series of challenges to metallurgists since 1988. Although fluorine is distributed throughout the gangue minerals contained within Ok Tedi ores, itsÆ presence in talc and phlogopite (naturally floating fluorosilicates) has proven to be the predominate sources of fluorine in the final concentrate. Initial treatment for the fluorosilicates consisted of the use of a carboxy-methyl cellulose depressant added to the flotation cleaners. This was superceded in 1998 with the installation of a fluorine reverse flotation process for the removal of naturally floating fluorosilicates from the final concentrate when the fluorine content of the final concentrate exceeds smelter-defined trigger points. The fluorine reverse process is similar to by-product molybdenite concentrate production in that sodium hydrosulfide is used to depress copper/gold flotation whilst allowing the fluorosilicates to float. The process was installed in two parallel modules (to match the existing grinding/flotation modules at Ok Tedi), each consisting of a closed rougher/cleaner circuit configuration. Both rougher and cleaner cells are Jameson Cells from MIM Process Technologies, with the selection based on both processing characteristics and available construction space. This paper discusses both the nature of fluorine in-, and its removal from-, Ok Tedi copper/gold concentrates.

Jan 1, 2003

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By J D. Illescas, S N. Arnold, D R. Shaw

Ion exchange (IX) as a primary production technique has been applied commercially since the 1950s; its application in the uranium industry continues to be widespread and is utilised to a lesser degree in the gold industry. The majority of ion exchange applications, outside of gold and uranium, have primarily been for secondary metal recovery and impurity removal. Newer developments in the application of ion exchange, as well as changes in regulatory requirements, are bringing about the wider use of ion exchange as a primary production technique not only for high value metals such as uranium, platinum group metals (PGM), refractory metals and rare earths, but also looking at base metals such as nickel and copper. The ability to build lower-cost, safer, less polluting processing plants with smaller footprints is driving a greater interest in IX, with the main competitors remaining solvent extraction and carbon-in-pulp/leach. This paper discusses a number of areas where IX has been applied and its advantages compared with other techniques.CITATION:Shaw, D R, Arnold, S N and Illescas, J D, 2012. Ion exchange in hydrometallurgy - Secondary metal removal or primary production technique?, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 17-22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The effectiveness of three different types of longwall chock under the three different types of geological conditions worked recently is outlined. Some provisional analyses of the variation of chock load under the shale roof con- dition are briefly discussed and some problems and solutions of gateway and road- head support outlined.

Jan 1, 1974

By Gonzalez-Dominguez J. A, Dreisinger D. B

At Cominco's Zinc Refinery at Trail, British Columbia impurities are removed from zinc sulphate electrolyte by a two-stage purification process using zinc dust. Copper, cadmium and thallium are removed in the first stage whereas cobalt is removed in the second stage. Cobalt removal kinetics are affected by soluble antimony and copper additions to the electrolyte. This study was focused on the kinetics of cobalt removal by zinc powder cementation. Experimental variables included copper and antimony concentrations, pH and temperature. Common organic additives employed in zinc plants were studied to determine potential interactions with the cobalt removal process. Cementation products obtained from laboratory experiments and plant practice were studied using SEM. A number of significant results were obtained: 1. Copper and antimony ions were sustantially removed from solution during the early stages of the cementation reaction (within the first 15 minutes). Cobalt cementation kinetics are slow and follow a first order kinetic regime. 2. A drop in the cobalt removal rates can be correlated with a rise in the Eh of the slurry. 3. Ligninsulphonate, Percol 351 and animal glue at levels of 2 mg/L significantly impede cobalt cementation.

Jan 1, 1993

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By N M. Player, R P. Varden, E Jones

"An effective geotechnical design provides an accurate and appropriate assessment, balanced with a mining company’s risk profile. Justifying the cost of slope assessment requires an understanding of the input sensitivities, and resultant risk, to achieve a slope of a required functionality. As a project progresses from Scoping to Feasibility, the geotechnical risk becomes better resolved through increased expenditure on drilling, testing, analysis and modelling as long as the input data is appropriately spatially distributed. Providing accurate and appropriate geotechnical assessments in the early stages provides confidence in all following stages, especially where initial analysis indicates difficult geotechnical conditions. It is also in the early stages of project definition that there is most opportunity to maximise the value of the deposit through investigations into optimal mining methods.This paper examines the advantages of geotechnical engineering input through a project study period. Early geotechnical involvement allows the Scoping and Pre-Feasibility Studies to be more effective. Operational risks can then be better understood and dealt within the Feasibility Study phase, also ensuring that the correct risks and management controls are put in place.With commodity price pressure and cost of resource recovery in a downturned industry, reducing the risk to cash flow, resource recovery and safety should be a primary goal for all mining companies. Reduced risk can be effectively achieved through geotechnical design of slopes to achieve a required performance as part of an integrated study to the Reserve definition and mine design.Citation:Varden, R P, Player, J R, Player, N M and Jones, E, 2016. Justifying Slope Design Risks and Costs, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 185–201 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016