Search Documents

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By A Giyose, V Malysiak, K Davey

Batch flotation tests were conducted on a haematite-bearing Sishen iron ore slimes sample from South Africa using reverse cationic flotation. The effect of grinding on flotation performance, the flotation response of various key impurities in the sample, and the feasibility of increasing metal recovery by refloating tailings in a scavenger flotation step were investigated. The test results indicate that reverse cationic flotation is effective in rejecting impurities from the iron ore sample tested. From a head grade assaying 6.4 per cent SiO2, 2.14 per cent Al2O3, 0.402 per cent K2O, 0.082 per cent P and 0.194 per cent TiO2, the levels of impurities were reduced to 1.83 per cent SiO2, 0.88 per cent Al2O3, 0.095 per cent K2O, 0.066 per cent P and 0.174 per cent TiO2 in the final concentrate at a Fe recovery of 74 per cent. The flotation response of SiO2, Al2O3 and K2O were found to be better than that of P and TiO2. The testwork demonstrated that grinding to 80 per cent passing about 49 microns is essential for upgrading the Sishen iron ore to produce >67 per cent Fe concentrate grade. This grind size corresponds to about 80 per cent liberation of haematite from the gangue minerals. Fe recoveries up to 76 per cent were obtained by refloating the rougher tailings in a scavenger stage, with little effect on the final concentrate grade. Size-by-size Fe recovery data obtained indicated that particles below ten microns were mostly lost in the desliming stage conducted prior to flotation whilst some reported to the froth by entrainment. Some of the coarser haematite-gangue composite particles reported to the froth product by genuine flotation.

Jan 1, 2009

By C Fischer

The introduction of digital communications technologies into the underground mining industry, in both coal and hard rock mining, has enabled high bandwidth applications to be applied in the mining industry. Digital networks based on 802.11 b/g/n open Wi-Fi standards have allowed numerous applications to be run over a single communication backbone. One of the many important applications is the tracking of personnel and equipment via RFID Tags. This tracking application has formed the basis of a Proximity Detection System or Collision Avoidance System (Schiffbauer and Mowrey, 2001; Kent, Fischer and Schiffbauer, 2011) thereby improving safety and increasing control in the mining environment. This paper discusses the growth of digital technology as the backbone for communications in underground mining applications. This growth has allowed the ‘convergence of technologies’ (occurring in the general business world) to be available to mine operators in general and underground mine operators in particular. Mine Site Technologies’ involvement with major mining companies and mining equipment manufacturers (OEMs) in developing and supplying their communication systems is also discussed.The latest technical requirements and specifications for communication systems for underground and open cut mines will be reviewed.

Nov 22, 2011

By Stevenson BG

The relevance of ore-dressing mineralogical investigations to developing and improving metallurgical flow-sheets is discussed and examples are given of the application of such studies to various types of ores and mill products (Au, Cu-Sn, Ni and Sn). The mineralogical investigations described illustrate (a) assessment of the feasibility of ore pre-concentration by heavy-media cyclone separation, (b) evaluation of the potential applicability of various metallurgical treatment processes to an ore, and (c) characterization of mill products to assess circuit efficiency and to guide circuit modifications.

Jan 1, 1978

The development of the Moura Coal Preparation Plant is described, commencing with the first'stage of the plant commissioned in 1963. The subsequent expansion stages are traced through to October, 1973. The plant has undergone frequent stages of expansion and modification and this process is continuing. The development programme for 1974 is described as proposed in late 1973. The characteristics of the Moura and Kianga field coal seams with respect to washability are summarised and some comment is made on the blending of these coals prior to washing, to ensure production of export grade coal within specification.

Jan 1, 1974

By P Mulvey, M Stuckey

"Inter-aquifer leakage due to fractures caused by coal seam gas extractions or longwall mining is an important issue for both the gas and coal industries. Currently, predicting stress induced macro-porosity associated with hydraulic fracturing, depressurisation via dewatering or collapse of overlying seams to infill a void left by longwall mining, is problematic. If fractures can be located the fracture can be sealed. Locating fractures is difficult. The non-geophysical approaches to locate fractures has been to consider the mixing of different waters, particularly that of more recent shallower groundwater with older deeper groundwater, via differences in radio-isotopes integrated with geochemical models to predict likely mixing of waters. This approach is applicable under appropriately complex settings; however, it is an expensive technique and is based on the assumption that the daughter isotopes are equally non-reactive which may not always be the case.Potentially a cheaper and faster technique is to consider integrating geochemistry (mineral weathering) and hydrogeology. The chemistry of groundwater, controlled by the weathering of primary rock?minerals and?formation of secondary minerals, can not only be differentiated between geological strata but also within strata as different stages in weathering results in differing impacts on water quality (ie different reactants).Field analysis of pH, electrolytic conductivity (EC), oxidation reduction potential (ORP) and dissolved carbon dioxide together with laboratory analysis of dissolved constituents characterise the chemistry of the water. Collection of rock samples at the time of drilling for bore installation can provide the (only) opportunity to assess the media in which the groundwater resides and migrates through. An assessment of aquifer matrix chemical makeup, via bulk sample chemical analysis, X-ray diffraction (XRD) and petrographic analysis can achieve this.The chemistry of groundwater is dependent on the water velocity. Water at deposition and post-diagenesis dissolution of minerals by hydrolysis and oxidation will result in equilibria of the dissolved phase with the solid phase. Post-depositional fractures caused by either tectonic activity or weathering alter the rate of weathering and thereby the geochemistry. Slow water flow in microfractures results in water in equilibrium with the rock minerals. Faster flow in larger fractures results in water being in disequilibria with rock minerals.Fractures can alter groundwater chemistry by two pathways: changing groundwater velocity, which changes the rate of hydrolysis or oxidation mixing water from different geological strata.Both pathways cause subtle changes in the water chemistry.It is however, the dissolved phase chemical data, which can be observed over time at individual locations and/or at a point in time along a flow path, which allows the hydrogeologist to ælook up-gradientÆ and locate the zone of leakage. Hence, influences on rock/groundwater chemistry, from anthropogenic sources to natural mixing of waters, can be assessed via appropriate interpretation of geochemistry, hydrogeochemistry and flow data.This paper will use the example of the geochemical and hydrogeological characterisation of aquifers within the Hawkesbury and Bulgo Sandstone of the Southern Coalfields to the south of Sydney in New South Wales to demonstrate this approach.CITATION:Stuckey, M and Mulvey, P, 2013. Looking for fractures - integrating geochemistry with hydrogeology to find inter-aquifer leakage above dewatered or collapsed coal seams, in Proceedings Water in Mining 2013, pp 99-108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By K G. van den Boogaart, M Lehmann, U Mueller

Geometallurgical parameters are descriptions of the mineralogy and microstructure of the ore determining its mineralogical and microstructural characteristics. From a conditional geostatistical simulation of such properties, a processing model can compute recovery, equipment usage, processing costs, and thus the monetary value for mining and processing a block with certain processing parameters. The output can be used for optimising mining sequences or finding optimal processing parameters by solving the corresponding stochastic optimisation problem.The approach requires two properties of the simulation not provided by established geostatistical techniques:Many relevant geometallurgical parameters are from non-Euclidean statistical scales such as (mineral) compositions, (grain size) distribution, (grain) geometry, and (stratigraphic type) categorical, which might produce nonsensical values (for example, negative proportions, negative facies probablities, planar grains) when simulated with standard geostatistical techniques.Due to the nonlinearity of processing, the entire conditional distribution of the geometallurgical parameters is relevant, not only its mean and variance. The geostatistical simulation needs to reproduce the joint conditional distributions of all the geometallurgical parameters.The multipoint conditional geostatistical simulation technique discussed here allows for jointly simulating dependent spatial variables from various sample spaces. The technique combines an infill simulation, similar to the one used in multipoint geostatistics, with a new form of distributional regression to estimate conditional distributions of arbitrary scales from different information sources, including training images, training models and observed data. The distributional regression is based on a generalisation of logistic regression and is related to both Bayesian Maximum Entropy geostatistics and high order cumulants.The method ensures that simulated data reside in the set of possible values and honour the characteristics of the joint distribution to be reproduced. The computational effort is substantial, but affordable for a useful application with standard problems: from processing-aware block value prediction and block processing optimisation as shown in the test application to a mathematically completely defined simulated model situation with a complex processing model.CITATION:van den Boogaart, K G, Tolosana-Delgado, R, Lehmann, M and Mueller, U, 2014. On the joint multipoint simulation of discrete and continuous geometallurgical parameters, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 379–388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By K Lee, L Mann, J Bygrave, G Sheldon

Ausmelt is supplying commercial quantities of an alkyl hydroxamate flotation collector AM28 for flotation of oxide and supergene base metal ores and tailings. AM28 is a non-hazardous product used as a ten per cent to 50 per cent solution in dilute potassium hydroxide. It is a selective flotation collector for oxide or oxidised base metal minerals and replaces conventional sulfidisation for oxide mineral flotation. At Radio Hill, the AM28 is used in conjunction with traditional sulfide collectors, which allows simultaneous flotation of oxide and sulfide copper minerals. The Fox Resources Radio Hill copper concentrator near Karratha, Western Australia, is currently configured to treat supergene copper ore sourced from the West Whundo open pit. This Archean VMS type copper deposit has been deformed and remobilised with uplift, erosion and weathering to form a significant supergene zone. The sulfide copper minerals present in the upper zone are digenite and chalcocite with lesser chalcopyrite and covellite. Oxide copper minerals present include cuprite, with lesser malachite and azurite. Gangue minerals include quartz, talc and chlorite. Plant trials at Radio Hill are reported for supergene West Whundo ore, where the AM28 was stage added into the circuit at nominally 80 g/t. Plant data over three months shows the copper recovery increased consistently from around 50 - 60 per cent to above 70 per cent when AM28 was added. This has been proven statistically. The grade of the concentrate was consistent with and without AM28, at nominally 22 - 24 per cent copper.

Jan 1, 2007

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

This paper outlines the advances made in vacuum filtration as developed by Outomec Process Filters and details the results obtained at a number of Australian installations. The first section of the paper details the technical advances made by the use of ceramic media in vacuum filtration and explains the reasons for the use of the technology. The second part of the paper discusses a number of Australian installations of the ceramic vacuum filter and where possible compares the actual experiences with those predicted from the test work which preceded the installations. The Ceramec Capillary Vacuum Filter is a vacuum disc filter which combines the proven mechanical attributes of a disc filter with exciting new ceramic vacuum technology from Outomec of Finland.

Jan 1, 1991

By Kellerwessei H, Oberheuser G

A major breakthrough in extending the life of the wear material of high pressure roll crushers when treating moist, highly abrasive material has removed the last impediment to the widespread acceptance of high pressure comminution in the minerals industry. The system is very energy efficient. It has been demonstrated that in the cement industry energy savings of up to 50 per cent have been achieved compared to conventional hall milling. Besides being energy efficient, the process provides some remarkable and useful effects; ò better liberation of mineral constituents (as proven for diamond liberation). ò preferential comminution where induced micro fissures follow grain boundaries. ò higher reactivity of the product due to micro fissures. All these points will be described here together with a review of current flowsheet design and incentives for the use of this method of Comminution.

Jan 1, 1993

By burgess F, Manlapig E. V, Franzidis J. P

Bubble surface area flux, a parameter which is determined by bubble size and superficial gas velocity, has been identified as a criterion for flotation scale-up from a metallurgical point of view. Investigations at Hellyer, Scuddles and Mt Isa

Jan 1, 1997

For some time fine coal (-0.5 mm) flot ation has been considered as a bulk flotation problem. Combinations of hydrocarbon oils and frothers have been used as surface active agents in coal flotation. The selectivity of the flotation process has always been poor in such cases. With the increase in fine coal production due to mining methods and coal handling systems, optimisation of fine coal treatment.has become important. Petrographic and mineralogical composit- ions of coal particles have been reported to influence their flotability. The problem becomes more complex due to surface oxidation of coal and the presence of slime forming clay minerals in the run of mine coal. In this paper, the flotation problem is examined on the basis of various constituents of coal and their associated gangue minerals. The selection of reagents has been suggested on the basis of their surface chemical properties. Factors such as surface modific- ation of coal and gangue materials, flotation kinetics and hydrocarbon oil - coal inter- action have been critically evaluated to improve fine coal flotation recovery.

Jan 1, 1978

By Morrell S

As more and more autogenous and semi-autogenous mills are run in closed circuit with cyclones the limitations that can be imposed by poor grate and pulp lifter design are becoming increasingly apparent. Relevant literature on the subject is al

Jan 1, 1997

The Hishikari gold deposit, discovered by the Metal Mining Agency of Japan, has become a giant class epithermal gold deposit with the highest grade of gold yet recorded in the world through detailed exploration and development by the Sumitomo Metal Mining Co., Ltd. The exploration strategy involved a regional approach combining geological and gravity surveys over a 900 km2 area which had historically produced over 120 t of gold. These surveys were carried out to grasp the common geologic features of epithermal gold deposits in the survey area. A genetic model for epithermal gold deposits in the area under regional survey was also considered based on detailed research of the Kushikino epithermal gold deposit which was in operation at that time. This model was applied to the targeted areas, and important relationships between mineralization, host lithology, intensive propylitic alteration and gravity highs became apparent. The Hishikari block was selected in this way and bonanza gold was discovered during drilling. Since the development of the Hishikari mine, information useful for further exploration for the same type of deposit has been accumulated.

Jan 1, 1995

By B Flynn, P Knights

Low-loaders or 'floats' for relocating equipment in surface mines are limited to a capacity of approximately 350 t. In the iron ore industry it is desirable to be able to rapidly relocate excavators in order to maintain production rates within appropriate quality limits. In addition, the ability to rapidly relocate heavy equipment raises the possibility of improving the quality of repairs by performing maintenance in controlled shop conditions. However, many iron ore operations operate hydraulic excavators in the 600 to 800 t range, with newly released excavator models exceeding 800 t. These excavators are too large to float using conventional technology. This paper examines the potential for using multi-bogie transporters to relocate large hydraulic excavators in surface mines. Recent innovations have seen the development of modular transporters which can be coupled together to achieve larger platform areas. When separated, and with their drive bogies neutralised, these units are able to be towed behind prime movers and relocated between mines via public roads. The potential cost savings for relocating a Terex RH170 excavator in an open pit coal mine are examined. In the first six months of 2008, the analysis showed the potential for a 38 per cent reduction in total travel time with a corresponding revenue increase of approximately $350 k. The paper recommends that a feasibility study be conducted into offering a heavy equipment relocation service within the Pilbara region.

Jan 1, 2009

By D Capstick, M B. Ebell

This paper describes the test work, process design, commissioning and operation of a processing system at the Ergo gold operation that improves the extraction efficiency from gold tailings material. The improvement in recovery is derived from the separation of the gold contained within the sulfides of the tailings material and a dedicated process stream to recover that gold.The sulfides are separated by means of a flotation circuit and that resulting concentrate is subjected to a regrind of below 20 ¦m to enable a greater liberation of the gold. The ultra-fine material is then subjected to a dedicated leach circuit to recover the now exposed gold particles.The case study is an example of the challenges of introducing new technology and methodologies to a well-established operation and thereby attaining improved efficiencies and tangible business benefits.CITATION:Ebell, M B and Capstick, D, 2013. Improving extraction efficiency from Witwatersrand gold tailings using flotation and ultra-fine grinding of concentrates, in Proceedings World Gold 2013 , pp 301-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Process variables in flotation circuits are outlined with a view to producing mathematical models of circuits. The nature of the kinetics of flotation are discussed and the effect of process variables on the kinetics considered. An approach for a possible model is briefly outlined.

Jan 1, 1971

By Baafi EY, Sun Y, Tague I

Field trials at three New South Wales and one Queensland coal mines were carried out to gather data on oxygen "run out" times of Self-Contained Self Rescuers (SCSRs), time taken to escape from the mine, distances travelled and the average heart rate of subjects wearing SCSRs. The study has led to a method of predicting the duration of oxygen supply from a SCSR as a function of the wearer's body weight, physical fitness and the prevailing environmental conditions. Escapeway design, planning for emergencies, familiarity with SCSRs and experiential escape training are critical to control panic and maximise the likelihood of survival of a person attempting to escape in an emergency involving fire or explosion.

Jan 1, 1998

By Hampshire MJ

The tailing retreatment project rated at 10 000 t/day commenced operations in October 1982. The operation consists of dredging, feed preparation, cyanide leaching and carbon-in-pulp (CIP) gold recovery followed by Zadra atmospheric stripping and electrowinning. For the first two years the operation was adversely affected by excessive cyanide consumption and low gold extraction. Investigations demonstrated that the very fine, or slime, fraction of the tailing was the dominant consumer of cyanide and dissolved oxygen. The plant flowsheet was subsequently modified by inclusion of 80 - 100 mm dia. cyclones for slimes separation and a 31 m dia. thickener for water recovery. Treatment of deslimed feed in the CIP plant has reduced sodium cyanide consumption from an average 1.85 kg/t to 1.15 kg/t. The reduced oxygen consumption by the CIP plant feed has resulted in higher dissolved oxygen levels, frequently reaching supersaturation after 4 to 5 h contact time. This has allowed much improved gold extraction from the existing CIP plant capacity. Gold extraction from the mixed pyritic siliceous tailing has improved from an average U prior to desliming to a current 57%. Investigations are continuing on the recovery of gold from the discarded slimes.

Jan 1, 1986