Search Documents

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of 'some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement's gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that' faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By Oliver Bowles

WHILE vast quantities of limestone and dolomite. are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone' for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

Jan 1, 1928

By Oliver Bowles

WHILE vast quantities of limestone and dolomite are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate dis¬cussion of metallurgical limestone problems.

Jan 1, 1928

By W. T. Thom

RegaRding the elements necessarily involved .in working out a scientific scheme of classification, Stansfield and Sutherland, (94)† quoting Grout, (34) make the following statement: All bases (for a scientific classification) should be capable of quantitative determination, or be exactly related to some property capable of such a test, so that, if no natural groups are found, arbitrary lines may be drawn to limit the classes. The best basis for classification should involve inherent and fundamental qualities of the materials considered. Allied to this is the requirement that advantage should be taken of any natural grouping. As a further help in selection, the bases or tests should be easily applied, widely known, and have a wide range of values in the material classified. In order that we may apply the philosophy thus expressed, it is necessary for us to have clearly in mind both the reasons why coals differ and the specific purposes to be served by the classification to be devised. Coals differ because, as modern science has shown, coal beds are actually neither more nor less than buried and altered peat deposits, formed in remote geologic time. And as is generally known, such peat beds consisted of masses of partly macerated and decayed trees, shrubs, plants, mosses and/or algae, deposited under swamp or semiswamp conditions. It is therefore to be expected that coals will vary: 1. Because of differences in the parent vegetation, due either to evolutionary plant changes, as from the fernlike types of the Paleozoic to the coniferous and hardwood types of the late Mesozoic and Tertiary; or due to the differences in floral assemblages (growing at the same time) induced by differences in local environmental conditions. For example, moss, sedge, woody and other peats are today accumulating simultaneously in different bogs in North America. 2. Because of differences in the stage to which bacterial decay proceeded in the peat bed. Peats laid down in stagnant waters suffer

Jan 1, 1932

LEAD and tin mixed together make an alloy through an attachment of natural affinity which they have with each other, so that when they are mixed it is difficult to recognize by the sight which one it is, if the essences of their qualities are not surpassed by more than half. If, indeed, one can be recognized, it is the tin which gives off a certain sharp odor to the sense of smell, besides having a greater hardness and whiteness. The best of these is the one that is the purest in its kind. In the alloy of tin it is the one that is the whitest and hardest, or, when it is bent or some thin end of it is held tightly by the teeth, is heard to crackle as frozen water does. Because this happens more with this than with other metals, I do not wish now to inquire into it. It is enough that it be a sign for recognizing when tin is pure or mixed. Pewterers say that it should be joined in alloy with lead and that it is better for working when it contains four or six pounds to the hundred because it makes it softer to the hammer and more fluid in casting. But I do not like to hear this, even if all they say is true, for I see that the tin that comes from England, when worked as well as in cakes that show it to be pure, is much more beautiful and better in all works than is that made in Venice. And I believe that it is not better for any work when mixed than when pure, except for the advantage of the master who, if he does nothing else, sells lead that is worth little for tin that is worth much. I find that when mixed it serves in only two things. One is when it is wished to make a solder for copper, for use when it is not worth while to solder the bottoms and large pieces of vessels with low-grade silver as should be done. The other is when master potters calcine it in order to make glazes and to apply white to their vases. I consider lead to be useless in all other works of any kind of metal, since it unites with none of the other metals of good company except tin.

Jan 1, 1942

By Richard Moldenke

The author discusses some economic conditions which have made the career of the cast-iron pipe industry in the United States a checkered one. He next describes the two new developements in the manufacture of cast-iron pipe-both along the lines of centrifugal casting. The advantages and disadvantages of both processes are presented in some detail. Finally, statistics on the production of pipe in the United States at the present time are given, as well as the plants-and their capacities-so far as these are situated in the South. No SINGLE branch of the foundry industry has been brought to a production basis of huge tonnage, low manufacturing cost, and producing material of a remarkably high quality, as has the making of cast-iron pipe. The pipe shop is an excellent illustration of the fact that repetition work in specialties leads to mechanical equipment and manipulation that lower production costs to an. astonishing degree. Hence cast-iron pipe, in dull times, has been sold at a few dollars a ton over the selling price of the pig iron used. On the other hand, these same pipe, shops make fittings .of many varieties, and in much smaller quantities, where the cost is high, and when pipe may be sold, say, at $50 a ton, the fittings on the same shipment will be sold for nearly double that price. The history of pipe-making, in the United States, is a checkered one the mortality of plants is high and, from the nature of the industry, plants must be large to live. In spite of the fact that the best processes must be used to turn out this rather strict specification material, pipe is easy to make and a pipe plant is more of a tonnage mill than the really high-class specialty foundry it should be. Every time, therefore, that the demand for pipe is strong new shops spring up, only to close when the demand has ceased, but the financial damage to the more permanent plants has been done. Both the South and the North have had abundant experiences of this kind, and when recently a northern Public Service Corporation gave its order to France, the pipe plants thus adversely affected were content to have this occur rather than see-a plant started to supply the surplus demand.

Jan 9, 1924

INSTITUTE MEDALS AND PRIZES ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows The Robert W Hunt Medal, The Hadfield Prize, The J E Johnson Jr , Award, The Lewisohn Platinum Prize to senior members, and the President's Prize to junior members ROBERT W HUNT MEDAL The partners of Robert W Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules, 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to, the younger men, rather than the medal 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee consider¬ing the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improve¬ment of production and quality of material 3 A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the award subject to approval 4 The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute 5 The recipient of the award shall be designated "The Hunt Medallist "

Jan 1, 1923

By V 7. 0 / 300 dpi

WHEN the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick -was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of all average sample of this quartz is: SiO2,, 96.7; Fe203, 0.3; Al203, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then clumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the. material would not be plastic enough to mold. After a few minutes' grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected

Jan 9, 1913

5. The medal committee may invite nominations from the membership of the Institute, such nominations to be accompanied by an argument in favor of the award and details sufficient for a proper citation to be drawn. This medal has been awarded as follows: 1927—David William Brunton. 1929—John Hays Hammond. 1928—Herbert Hoover. 1930-Daniel C. Jackling. Miscellaneous Prizes Many of the Local Sections have established or administer prizes for the best paper presented within the year by any junior member. Annual Lectures Howe Memorial Lecture The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated: 1924 What is Steel? By Albert Sauveur. 1925 Austenite and Austenitic Steels. By John A. Mathews. 1926 Twenty-Eve Years of Metallography. By William Campbell. 1927 Alloy Steels. By Bradley Stoughton. 1928 Significance of the Simple Steel Analysis. By Harry D. Hibbard. 1929 Studies of Hadfield's Manganese Steel with the High-power Microscope. By John Howe Hall. 1930 The Future of the American Iron and Steel Industry. By Zay Jeffries. Institute of Metals Lecture An annual lectureship was established in 1921 by the Institute of Metals and it has come to be one of the important functions of the Annual Meeting. A number of distinguished men from this country and abroad have served in this lectureship. The roll is quoted below: 1922 Colloid Chemistry and Metallurgy. By Wider D. Bancroft. 1923 Solid Solution. By Walter Rosenhain. 1924 The Trend in the Science of Metals. By Zay Jeffries. 1925 Action of Hot Wall: a Factor of Fundamental Influence on the Rapid Corrosion of Water Tubes and Related to the Segregation in Hot Metals. By Carl Benedicks. 1926 The Relation between Metallurgy and Atomic Structure. By Paul D. Foote. 1927 Growth of Metallic Crystals. By Cecil H. Desch. 1928 Twining in Metals. By C. H. Mathewson. 1929 The Passivity of Metals, and Its Relation to Problems of Corrosion. By Ulick R. Evans. 1930 Hard Metal Carbides and Cemented Tungsten Carbide. By 8. L. Hopt.

Jan 1, 1930

By T. Sterry Hunt

In my address on the " Geognostical Relations of the Metals," delivered before the Institute on the 20th of February last (Vol. I Transactions, p. 331), I spoke of the rocks in the vicinity of Thunder Bay, Lake Superior, where I indicated two series of uncrystalline rocks resting upon the Huronian schists, the lower one consisting of dark-colored argillites and sandstones overlaid, apparently in slight discordance, by nearly horizontal red and white sandstone and marls, which were compared with those of Sault Ste. Marie, and those of the Portage Lake district, on the south shore. These latter sandstones, according to Brooks and Pumpelly, overlie uncomformably the Keweenaw series of copper-bearing amygdaloids, sandstones, and conglomerates, and are in turn overlaid by the Trenton limestone. I then proposed to call this lower series of Thunder Bay, that is to say, the dark-colored argillites and sandstones which are traversed by the silver-bearing lodes of that region, the Animikie group. Shortly after the publication of that address I received an abstract of a paper on the geology of that region by Professor Robert Bell, read before the Montreal Natural History Society, February 24th. He there confirms the statement made in my address that the gold of Lake Shebandowan occurs in the Huronian, which is also seen to be cut by the silver-bearing lodes just mentioned. Professor Bell, in this paper, proposes to designate both what I have called the Animikie group, and the overlying red and white sandstones, by the name of the Nepigon group, for the reason that the upper series is best displayed about Lake Nepigon. This latter series is by Logan supposed to be overlaid by the copper-bearing amygdaloids with conglomerates and sandstones of the north shore (apparently identical with those of Keweenaw); and the whole together, inclnding the Animikie group, constitute his Upper Copper-bearing group. These copper-bearing strata are by him supposed to be overlaid by the red and white sandstones of St. Mary, which are apparently the same with those sandstones which, according to Brooks and Pumpelly, overlie unconformably the similar cupriferous rocks of Portage Lake, and are, in their turn, overlaid by the Trenton limestone. Thus the sandstones which at Thunder Cape overlie the Animikie group are by Logan placed in the midst of the Upper Copper-bear-

By T. Sterry Hunt

IN my address on the " Geognostical Relations of the Metals," delivered before the Institute on the 20th of February last (Vol. I Transactions, p. 331), I spoke of the rocks in the vicinity of Thunder Bay, Lake Superior, where I indicated two series of uncrystalline rocks resting upon the Huronian schists, the lower one consisting of dark-colored argillites and sandstones overlaid, apparently in slight discordance, by nearly horizontal red and white sandstone and marls, which were compared with those of Sault Ste. Marie, and those of the Portage Lake district, on the south shore. These latter sand-stones, according to Brooks and Pumpelly, overlie unconformably the Keweenaw series of copper-bearing amygdaloids, sandstones, and conglomerates, and are in turn overlaid by the Trenton limestone. I then proposed to call this lower series of Thunder Bay, that is to say, the dark-colored argillites and sandstones which are traversed by the silver-bearing lodes of that region, the Animikie group. Shortly after the publication of that address I received an abstract of a paper on the geology of that region by Professor Robert Bell, read before the Montreal Natural History Society, February 24th. He there confirms the statement made in my address that the gold of Lake Shebandowan occurs in the Huronian, which is also seen to be cut by the silver-bearing lodes just mentioned. Professor Bell, in this paper, proposes to designate both what I have called the Animikie group, and the overlying red and white sandstones, by the name of the Nepigon group, for the reason that the upper series is best displayed about Lake Nepigon. This latter series is by Logan supposed to be overlaid by the copper-bearing amygdaloids with conglomerates and sandstones of the north shore (apparently identical with those of Keweenaw) ; and the whole together, including the Animikie group, constitute his Upper Copper-bearing group. These copper-bearing strata are by him supposed to be overlaid by the red and white sandstones of St. Mary, which are apparently the same with those sandstones which, according to Brooks and Pumpelly, overlie unconformably the similar cupriferous rocks of Portage Lake, and are, in their turn, overlaid by the Trenton limestone. Thus the sandstones which at Thunder Cape overlie the Animikie group are by Logan placed in the midst of the Upper Copper-bear-

Jan 1, 1874

By R. J. Murphy, N. J. Grant, J. W. Dowding

A large number of blast furnace slag-metal tests were examined to determine if the manganese reduction could be used as a primary indicator of the degree of oxidation or reduction of the slag and of its desulphurizing power. Slag basicity and temperature were also evaluated. Two laboratory heats were made and sampled prior to reaching equilibrium to check blast furnace data. IN a recent investigation of the factors affecting desulphurization in the blast furnace, is was evident that manganese reduction appeared to parallel the course of desulphurization. Grant, Kalling, and Chipman1 pointed this out in a series of time studies utilizing closely controlled laboratory melts. Fig. 1 is a composite plot of sulphur removal and manganese reduction as a function of time under two slags of different basicity. Manganese reduction appears to approach equilibrium at approximately the same rate as does sulphur. It was also demonstrated that the addition of oxygen to the slag, as manganese oxide, caused a sharp reversal of sulphur from the slag to the metal.' It has been shown that "Excess CaO" was a primary factor in measuring the degree of desulphurization under ideal reducing conditions,1,2 the following reaction being representative of the process: CaO (slag) + S + C (solid) = CaS(slag) + CO (gas) It was also evident that a second reaction could drive the sulphur from the slag into the metal. A suggested reaction was' CaS (slag) + 0 = CaO (slag) + S Any change in the oxidizing power of the system would thus affect both the sulphur and the manganese without causing any change in the calculated basicity of the slag. "Excess CaO," "Excess Base," and other similar basicity values, under such oxidizing conditions, would therefore not be the best measure of desulphurizing power; instead, as was shown by and Chipman" he oxygen content of the slag at low oxygen levels would be the controlling factor. Unfortunately, the extent to which FeO is reduced in the blast furnace makes it difficult to utilize slag FeO as an accurate indicator of the degree of oxidation. By comparison, manganese reduction in the blast furnace proceeds more slowly and is generally only about 40 to 70 pct complete. manganese, which is present in significant amounts and is readily analyzed, offers an opportun-

Jan 1, 1954

Discussion of the paper of H. M. WARREN, A. S. BIESECEKER and E. J. POWELL, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 181 to 193. R.. V. NORRIS, Wilkes-Barre, Pa.-For many years the power requirements of breakers designed in the Anthracite. Region have been based on calculations made from indicator diagrams taken during operation, with various sections of machinery idle; these, while giving reasonably accurate figures, gave no intimation of the peak loads which have been shown so clearly in the paper. The high-speed flywheel for breaker rolls is new and shows a remarkable saving in peak power required, besides eliminating the stalling of the rolls from overload. The figures given are so far in advance of anything previously published that they will undoubtedly be used as a basis for future breaker design. It is to be hoped that the authors will continue this investigation and extend their paper by a description of the motors found best suited for this work. WILLIAM KENT, Montclair, N. J.-I notice on p. 187 reference is made to one of the difficulties being the starting torque, and it is proposed to use roller or ball bearings in order to decrease the high starting torque. I suggest that. before the roller or ball bearings are put in, an investigation be made as to the amount of the starting torque, as shown by wattmeter measurements and as to what the starting torque ought to be, theoretically, according to the energy formula; that is, how much starting torque is required to accelerate the rotating mass in a given number of seconds up to full speed. Having secured this information it may be found the amount to be saved by roller bearings is not very great. If it appears that roller bearings will not greatly decrease the starting torque, the next thing to be done is to have a special design of motor in which there is a field that can be made very strong at the start, by the use of extra poles or other means, and the next thing that may be done is to increase the speed from 10,000 r.p.m. to 25,000, which can be done with wire-wound flywheels, especially if the wires are made of vanadium steel.

Jan 5, 1916

Discussion of the paper of E. L. deGolyer, to be presented at the Colorado meeting, September, 1918, and printed in Bulletin No. 137, May, 1918, pp. 987 to1000. J. A. UDDEN,* Austin, Tex. (written discussiont).-I have read Mr. E. L. deGolyer's paper on The Theory of Volcanic Origin of Salt. Domes, with a great deal of interest. It seems to me a very able summary and discussion of the various theories set forth to account for the origin of our salt domes on the coast. It has always appeared to me that what we need is more observations on the facts involved and I regret very much that so far we have not been able to devote much time to the study of our salt-dome fields on the coast in this State. One feature that I do not find mentioned in Mr. deGolyer's paper is the so-called "cap. rock" overlying the salt. The nature of this rock seems to vary from a coarsely crystalline limestone to a fine-grained limestone containing sand and in which the limestone seems to be intersticially introduced material. We should be prepared to accept, if necessary, "more than one theory. To my mind, the igneous theory and the artesian theory, if I may so call it, may very well both be true. The "squeeze" theory and the artesian .theory may,, it seems tome also, jointly explain the phenomena. Neither the volcanic nor the salt "squeeze" theory explains the presence of the cap rock. The latter certainly does not explain the extensive sulphur deposits which occur in association with the cap rock. Whichever additional theory will be found best to explain the salt-dome structures, when we shall know them better, it seems to me that the theory first advanced by R. T. Hill and later elaborated by G. D. Harris, is not likely to be entirely replaced. Whatever cause has first set into action an upward circulation of gases and liquids in our salt domes, it seems to me that to a gentle circulation of the kind postulated by their theory is to be ascribed the uppermost and the later phenomena in our salt domes on the coast, with which we are most familiar; such as the cap rock, the sulphur, and the gypsum and anhydrite deposits.

Jan 7, 1918

By Ellen H. Richards

It is of importance to analysts to have a ready means of detecting the presence of small quantities of titaninm in iron ores and in certain fluxes and slags. The method given in Elderhorst's Blowpipe Analysis (fusion with potassium hydrogen sulphate) requires considerable practice, in order so to regulate the heat that the titanium oxide shall become soluble. In Brash's Determinative Mineralogy is found a method which, at least in inexperienced hands, has given better results, i. e., fusion of the substance to be tested with sodium carbonate on charcoal in the reducing flame. The solution in hydrochloric acid of the bead thus obtained, boiled with tin or zinc, gives the characteristic violet color; but when the mineral contains less than four per cent. of titanium oxide, long boiling and consequent concentration is necessary. In fact the test would seem to be much less delicate than is generally supposed. In the course of some analyses I quite accidentally found that a peculiar color is given to turmeric paper by solutions of titanium chloride. This color is hard to describe, being modified by the quantity of ferric chloride present in the solution ; but it is neither the orange of zirconia nor the red of' boron. It is rather a dull shade of purple, arid is easily recognized when the paper is dried, although the color fades in a few hours. By this means a solution containing .015 per cent. of titanium oxide can easily be tested. The same solution, treated with tin, required to be concentrated to one-tenth its bulk before a decided color could be obtained. The color given to turmeric paper is intensified after the solution has been treated with tin. This and some other indications show that the best shade of color is given by the titanons chloride rather than by the titanic chloride, and no other salt of titanium than the chloride has been found to give the color. Another peculiar property of titanium salts has come tinder my observation. When titaniferous minerals are soluble in nitric acid, and the solution is subjected to the action of the battery, the soluble titanium salt is converted into the insoluble oxide and appears on the electrode, in some cases, as a white coating; this

Jan 1, 1883

By Jorge Munoz Reyes, Guillermo

The new entity, Yacimientos Petroliferos Fiscales Bolivianos, created in 1936 for the development and exploitation of all petroliferous zones of Bolivia, including those formerly belonging to the Standard Oil Co., is doing its utmost to bring about rapid development and by this means to create a new source of revenue for the State. With this in view, Y.P.F.B. has opened a new field in the Samaipata region, on the main road between Cochabamba and Santa Cruz. Installation of machinery has begun for the drilling of several wells on the five anticlines that occur in this region. Work has also begun in the Saipuru field, on the Santa Cruz-Charagua highway, which was discovered by the Standard Oil and temporarily abandoned. In this new field, a topping plant will be installed, to supply gasoline and kerosene to Santa Cruz. Explorations are also being made on the neighboring structures of Saipuru. At the end of 1937, the committee that is to study the region of the Chapare in the northeastern part of Cochabamba, was organized. The structures were studied 10 years ago by Kirtley Mather and other geologists. It is hoped that by March 1938 this camp will begin work, as this zone gives promise of being valuable. Development The capacity of the refinery at Camiri has been enlarged in order that it may supply all the needs of that region. In order that the supply of crude may be adequate, several wells that had been almost abandoned by the Standard Oil are being cleaned out. New wells have been located at this camp following the principal anticlinal structure, and during the first half of the year 1938 several wells will be drilled. The same program is being followed in Sanandita but on a greater scale, as the nearness of this district to the Argentine border, which is the best market for the Bolivian petroleum of the south, allows immediate sale of the petroleum. Possibly a new refinery will be installed at this camp, as the one now in existence is only a rudimentary distillery. At the Bermejo camp, which is farther south, intensive work is being done to bring the wells into production. The Standard Oil produced limited quantities several years ago, but since 1927 the wells of this dis-

Jan 1, 1938

By David Keys

APPLIED geophysics is the youngest child of that old branch of learning, that has been known from Aristotle's time as physics-the constitution and laws of nature. The mother science, with the help of mathematics, has given birth to many children, who, on becoming of age in the scientific sense, wedded more practical applications which later became known as electrical engineering, physical chemistry and acoustical engineering. Some vigorous sons still retain the family name, among which the most recent to take its place as a division of science is geophysics, which deals with the physics of the earth. Geophysics in its broad sense has many departments-meteorology, oceanography and seismology, to mention only three. Within the past 20 years, however, a special interest has arisen in the application of physical principles to, problems in geology, mining and civil engineering, with the consequent rapid growth of what has now been called "applied geophysics." Applied geophysics in this narrower sense is the application of experi-mental and theoretical physics to determine variations: and discontinuities in underground structures that cannot be ascertained from surface inspec-tion. It seems evident, then, that the physics department is the natural place in a university where the principles and methods involved should be taught and developed, for the physicist will also have had the requisite training in mathematics that the proper understanding of many methods now used will require. A knowledge of the procedure and principles, however, is not sufficient for the successful application of geophysical, methods. One may know the dynamics of flight of golf balls and of impact and yet not play a par game of golf ! The proper selection and use of the right club to suit the circumstances of the lay of the ball and an acquaintance with the possibilities and limitations of the strokes as well as the practical execution of the play is essential to a successful game. So, also, in the application of geophysical methods, it is important for the geophysicist to use the best device under the conditions presented, to know the limitations of the conclusions deduced from his physical measurements and to make the proper interpretation of the results. A knowledge of geology will be of great aid in coming to the correct con-

Jan 1, 1938

By C. F. Willis

The time is no longer when a man can act as an independent unit; the appreciation of the interdependence of one man upon another has emphasized the importance of the social unit. Epidemics have made us recognize that even a man's health is not distinctly his own to control as he pleases. The physical examination of workmen previous to employment started with an effort to prevent the spread of tuberculosis, for tuberculosis may be detected in its early stages and cured. But it was soon found that many other diseases were detected and the saving of lives made possible. The physical examination does not mean the elimination of the unfit—on that basis it would utterly fail—but rather the measuring of a man's physical fitness and placing the man where he can do the best for himself, his fellow worker, and the company. Industry as a whole cannot expect to live up to the standard of physical examination set for the army, nor should it expect to do so, for in all branches of industry there are types of work that do not require the same amount of endurance as does army work, and the lacing of men with physical limitations in the work for which they are capable permits a higher average of physical fitness for the work requiring physical excellence. Objects of Physical Examination The objects of physical examination are: The early detection of illness, particularly at a time when a full restoration of health is possible; the protection of employees from infection caused by working in contact with contagious diseases; the discovery of a man's physical limitations, in so far as his possibility for rendering good service is concerned; assistance to the safety movement by eliminating association in hazardous occupations with men whose physical condition renders them likely to accident to themselves and others; and the lessening of time lost by sickness. Statistics issued by the United States Department of Labor show that 22.54 per cent. of idleness is caused by sickness, with an average number of 7.71 weeks idle; whereas only 1.66 per cent. is caused by acci-

Jan 1, 1920

To the American Institute of Mining Engineers: The committee appointed at the February meeting upon Railway Resistances would respectfully report: That one person has been constantly employed in calculating the results of the data taken prior to March 1st, 1876. Also to complete the data taken upon the Lake Shore and Michigan Southern Railway, a diagram was taken upon a through freight train from Cleveland to Chicago, and one from Chicago to Cleveland. So that now we have diagrams from Buffalo to Chicago and return, which, when fully worked up, will give results of the utmost importance in determining the cost of transportation of freight. These data will be of much importance in determining the proper methods of equating grades and curves, which is so essential in the location of new lines. The calculations show that instead of our attempting to formulate results from data obtained on one road, it will be best for the interests of transportation to enlarge the scope of our inquiries, and to extend the experiments so as to include all of the more probable causes which affect the cost of transportation. Were the details of railway equipment constructed alike, much work, which is now necessary, would be saved. It is not uncommon to find upon the same road 10 to 30 different patterns of something in construction to subserve the same purpose, which more or less modifies the friction of the cars. Take the majority of our trunk lines, with this diversity of construction, together with the varying conditions of track and manner of operating, and it will be at once seen that the labor and time to do the work and arrive at correct conclusions will occupy from two to three years. The results already attained in the short time in which they have been carried on, wholly by private enterprise, simply show what may be expected when the aid necessary is given to render them of the highest value to the great industries of the country. That the information may be general and of the greatest importance to our railway interests, the committee deem it advisable to secure, so

By R. P. Rothwell

THE milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I have thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value and interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern ; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a wet stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulphides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80-stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is man¬aged in a skilful and economical manner, though the necessity for * Read at the Montreal meeting, September, 1879.

Jan 1, 1880