Search Documents

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

By R. W. Raymond

In my former paper (Bans., xii., 410) I quoted the ruling of Judge Hallett, of Colorado, in the "Iron-Smuggler" case, tried before him in June, 1882. Under his charge, the jury in that case found for the defendants, practically declaring that the deposit on the outcrop of which the Iron Silver Mining Company's claim was located was not a " lode," or else that the portion of it within that claim was not the apex. The case was appealed, and the decision of the Supreme Court, given in February, 1886, is reported in 116 U. S. Reports, p. 529. It simply declares that there is nothing in the charge of Judge Hallett to warrant the setting aside the verdict. The definition of a legal lode given in that case, and quoted in my paper at the page above-named, is perhaps the best of several which Judge Hallet has pronounced. That is to say, his earlier definition, that " a lode or vein is a body of mineral, or mineral-bearing rock, within defined boundaries in the general mass of the mountain," is here accompanied with further explanations, which relieve it from the requirement on one hand, that the body shall be continuously ore-bearing if it he only well-defined, and, on the other hand, that the boundaries shall be well-defined if the ore-bearing body be proved to exist. So far as this particular case is concerned, the approval of this ruling by the Supreme Court merely prevents any re-hearing as to the face. Undoubtedly, the evidence was conflicting; and the jury chose to believe, for the purpose of that occasion, the " experts " who

Jan 1, 1887

By Harold Cook

THE purpose of this paper is to state briefly the inspection requirements of the Bureau of Ordnance, the specifications governing the inspection, and the physical and chemical properties of the steel used in the construction of ordnance for our Navy. It would be of interest to evoke discussion on points in these specifications which do not tend to insure the production of the very best material for the purpose intended. In other words, what requirements of our specifications are useless and also in what manner are our specifications deficient? It might be well at the, start to answer the first criticism of this paper which will probably be made, and that is that the title does not agree with the subject matter. Considering metallographic work as covering only the macroscopic and microscopic examination of metals, this paper will have gone beyond the subject; but it is believed that a broader definition of metallography is that it is the study of the relation of the internal structure of metals and alloys to their composition and to their physical and- other properties. The internal structure of steel is dependent on its physical and its chemical properties. These physical properties are dependent on the chemical composition and the mechanical and thermal treatment of the steel. So it seems that this subtitle would not be entirely necessary and that the title "Metallography of Steel for Ordnance Purposes" would cover a study, not only of what we can learn of macroscopic and microscopic examination, but broadly of the whole subject of the specifications, the fulfillment of the requirements of which produce the structural conditions revealed by macroscopic and microscopic examination. .

Jan 2, 1916

By Waldemar Lindgren

Jan 1, 1905

By George Young

DURING the spring of 1910 I visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and, even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. The principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories.

Jan 2, 1916

By M. Sagheer

This paper gives a report of the laboratory work investigating the fundamental flotation characteristics of chromite and its commonly associated mineral, serpentine. Floatability curves, showing floatability of chromite at different concentrations of sodium oleate and pH, were obtained by pick-up method. One of the difficulties encountered in flotation of chromite in presence of serpentine has been attributed to dissolved metal ions. The influence of metal ions, dissolved in pulp filtrate, on floatability of pure chromite and serpentine has been studied and it has been shown that Mg, Ca and Fe ions depress chromite. A considerable amount of work applying bubble pick-up method was carried out to counteract the depressing action of metal ions. Various methods and reagents were applied in this connection. Validity of each method and reagent has been discussed. Probably due to the abundance of high-grade chrome ores, very little has been published concerning the flotation of chromite. As improvements in mineral beneficiation are realized, more attention is being directed to low-grade ores previously considered unusable. Currently, gravity concentration is the principal process applied to upgrade chrome ores, but this cannot be used for finely disseminated ore because of the substantial losses in the fines,1,2,3 To avoid these losses, flotation can be applied to material which is too fine for satisfactory gravity concent ration, and it is probable that a combination

Jan 1, 1967

By I. G. Grettum, Eugene A. Stephenson

The flooding process was originally the result of accidents to casing and tubing, but it has gradually passed from an accidental condition to a definite engineering procedure. In spite of the general sheetlike char-acter of the major sand body, the position of shale bands, their thickness, the size of the grain and variations in effective porosity all give the sand different characteristics in different layers and in different places in the same layer. This condition has an important influence on the movement of flood oil and water, and on the yield per acre, as well as a bearing on what shall be considered the best method of handling flood wells. . A valuation takes into consideration six factors: (1) Flooding methods, of which four have been in common use, as follows, in order of effective recovery, (a) circular flood, (b) line flood, (c) five-spot and (d) five-spot with delayed drilling; (2) recovery per acre, which is definitely related to the oil content, the porosity, the method of flooding, the spacing program, and the continuity of the water supply; (3) the rate of production per well per day, which is definitely related to the mcthod of flooding, the oil content and the porosity of the sands; (4) the operating cost of the well, including royalty, overhead, taxes, etc. (Operating costs are usually expressed as unit cost per barrel.); (5) the expected price per barrel. It is safer to use the average price over a number of years than to attempt to forecast future price fluctuations. The discount factor (the sixth factor) used in appraisal of Bradford flood properties should be less than that commonly applied to other properties, because the hazards of operations have been reduced almost to those of a manufacturing industry.

Jan 1, 1930

By Charles C. Hall

The following procedure in estimating mineral oil when mixed with vegetable or animal oils, is the result of a long series of cxperiments based on the method suggested by Sir William Thompson and Mr. A. H. Allen, in a paper read before the Royal Society.* Four to five grams of the oil under examination are weighed out into a porcelain capsule of 75 C.C. capacity. Thirty C.C. of a 10 per cent. solution of potassium-hydrate in alcohol are added, and the capsule covered with a watch-glass is placed in a water-bath heated to about 93' C. The mixture of oil and alkali should be stirred frequently, and after three-quarters of an hour it is boiled with stirring. This will secure the complete saponification of all the vegetable or animal oil. After the boiling has been continued some time, and most of the alcohol is expelled and a thick scum of soap forms on the surface, a little bicarbonate of soda is added to convert the excess of caustic alkali into carbonate. When the contents of the capsule have become pasty an equal bulk of fine, clean sand is stirred in. This makes the soap granular, and facilitates the removal of the last traces of alcohol. The capsule is now heated for two hours more on the water-bath. After cooling, the contents of the capsule are transferred to a short-necked funnel, having a thin plug of asbestos, and washed with petroleum-ether, or some other light petroleum spirit. The ether dissolves out the mineral oil from the soap, and is best collected in a quarter-liter flask having a short neck. The ether can be applied conveniently and effectively by a small washbottle. Care must be taken to effect a complete removal of the oil

Jan 1, 1883

A. 0. ASHMAN, Palmerton, Pa. (written discussion *.).-Mr. Newcomb's paper has interested me greatly, as I have had numerous experiences along this line. I do not think enough emphasis can be put on his warn-ing to keep platinum couples free from contact with quartz tubes, as silica shows a tendency to alloy with platinum to a surprising degree even at low temperatures. I have frequently had evidence of silica contamination in a perfectly good tube, in which there was seemingly no possibility of a reducing atmosphere. This is rather important as it seems to be common practice to insulate, as well as protect, the wires by means of- capillary silica tubing, thus allowing the entire wire to be in contact with the silica. The best way to mount a couple in a silica protecting tube is by means of double-bore porcelain insulating tubes, the protecting tube being slightly longer than the couple so as to leave a space between the couple and the end of the tube. In this way there is no possibility of contamination from silica. In no case should silica capillary tubes be used to insulate platinum wires. Mr. Newcomb states that there is still much to be desired in pyro-meter protecting tubes; this is in keeping with my experience. From a practical standpoint there is not a satisfactory pyrometer tube on the market for high temperatures; with all clue respect to the many improve-ments and good work recently done in this line. I believe that the whole future development of pyrometry is dependent on the development of suitable refractories. With suitable refractories, for example, Darling's1 work with liquid couples could be developed to a practical basis, making possible the use of base-metal couples to replace platinum.

Jan 12, 1919

The entire War Minerals Relief Commission heard the case of the Chas. T. Pyrites & Chemical Company of Georgia on April 15 and 16. The Commission insisted on great detail with regard to the entire enterprise, although the main questions seemed to be of the amount involved. It is considered by the Commission that this claim comes unquestionably under the Act, it is one of the best examples that has been brought to the attention of the Government thus far. Testimony showed that operations were done on the property late in 1916 without request from the Government. Preparations were made to work the pyrites deposit on a comparatively small scale but , following a visit from a representative of the Secretary of Interior and a personal interview of the principal owner of the property and Secretary Lane, operations on a much larger scale were begun. The amounts expended prior to this interview were carefully separated from the expenditures thereafter. Testimony showed that it was the intention of the owners to transport their product by motor truck to the railroad-13 mi. away. This limited shipments to about 50 tons daily. Under the enlarged plan taken against the better business judgment of the owners, a railroad spur at a cost f nearly $200,000 was built to the mine. The operation included a concentrating mill with a capacity f 600 tons daily and an expensive dam to make possible the use of waterpower. With these improvements, the company was just beginning, operation under its enlarged program when the armistice was signed. This resulted in a greatly decreased demand and consequently lower prices, with all prospects indicating that the property could not operate profitably when Spanish pyrites begin to move.

Jan 6, 1919

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4O10(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. SOURCES At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This

Jan 1, 1940

By H. W. Hitzrot

THE new 4800-ton fine-grinding plant at the Hollinger Consolidated Gold Mines property at Timmins, in the Porcupine district of northern Ontario, went into operation in November 1937, and represents the culmination of an experimental program. The plant is a moderately low rectangular building of hollow tile on a steel frame, large enough to house four 7 by 15-ft. ball mills, with a 12 by 27-ft. classifier beside each mill. At one end is space for the addi-tion of another mill and classifier or a mill and classifier for the regrinding of table concentrates. This regrinding is now done in the old grinding department of the main mill building. Also within the new building are the four 6-in. sand pumps for lifting the product from the low-dis-charge ball mills up to the classifier feed launders and the containers and appurtenances of a complete dust-collecting system. Together with the usual overhead crane, these constitute the major units of equipment within the new plant. The location is at the lower end of the main mill buildings toward the old tailings pond, now so neatly leveled off and sodded to rival the very best of our own W.P.A. projects. Close by the new grinding plant is a large dome-shaped structure-the new fine-ore bin designed and built by Mr. Longmore and the Hollinger milling and engineering staffs. There are four separate automatically loaded inclined belt conveyors leading up from the bottom of the bin to the grinding plant. Each belt is equipped with a recording weightometer, in the grinding building. The whole structure and the machinery within it give the impression of permanence and a carefully integrated design with close attention to details, giving the operators every advantage for consistently good work.

Jan 1, 1939

ABIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has three major awards to make annually and one special prize for excellence in technical papers, as follows. The Robert W. Hunt Medal and Prize, The J. E. Johnson, Jr., Award, the James Douglas Medal, and The Lewisohn Platinum Prize to senior members. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting' ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules ? 1 The award shall consist of two prizes, first of a gold medal, second of a sum of money, a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2 The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material

Jan 1, 1923

By J. E. Warren

To clarify the specific questions raised by J. E. Warren's discussion, the following remarks are offered. 1. It is correct that stratification is assumed in the application of the statistical zonation technique, but this does not constitute a limitation. If, in fact, the reservoir is not stratified the zonation technique will show it. The reservoir is then considered as one zone with a particular distribution of permeabilities. 2. The statistical zonation technique was intended as wells may not be an adequate measure of the lateral permeability changes; e.g., if the data presented in Table A-4 of the subject paper are evaluated on the basis of two crossed classifications with interaction, the variation between zones is significant with a probability greater than .99; however, the variation betwen wells is also significant with a probability greater than .87. It is apparent that the technique suggested by the author can be generalized to provide a powerful method for describing petroleum reservoirs. This generalization can be achieved by treating the core data as a two-way classification to determine the between-zones and the between-wells variations; then, the build-up permeabilities can be analyzed, perhaps on at least-squares basis, to establish the probable distribution of the permeabilities within the zones associated with the individual wells. an additional tool for the reservoir engineer to use together with other techniques and all available information. If pressure build-up permeabilities are available, they should certainly be included. Pressure build-up tests were not available for the reservoir considered in the paper. 3. The proposed correlation of zones between adjacent wells was the best of the techniques that I examined. It is not so much a "measure" as an indication of lateral permeability changes, regardless of whether they are seemingly random or form an obvious trend.

By H. H. Campbell

In the extending employment of open-hearth steel for structural purposes, it is a matter of prime importance that the test-piece shall represent with practical accuracy the characteristics of every portion of the heat from which it comes. In ordinary practice this homogeneity is assumed; but inasmuch as leading exponents of the revolving-hearth system have claimed that a reasonable uniformity could be obtained by their method alone, it may be pertinent to offer a few facts on the subject. The following heats made by the Pennsylvania Steel Company, for bridge-work, were tested by casting two four-inch ingots, one being taken during the first third and the other during the last third of the cast. Test-pieces obtained from these small ingots usually give results inferior to those obtained from larger sizes; but for purposes of cornparison they are equally conclusive. Many of the tests were made for experimental purposes within a few hours of the time of rolling, and before sufficient time had elapsed for the usual molecular redistribution necessary for the best results. All the tests were made on 3/4-inch rounds just as they left the rolls and without annealing; the results, therefore, are subject to the errors caused by variations in the diameter, and in the temperature at which the bar was finished. The tests from any one heat, however, were always nude as nearly as possible under the same conditions; and inasmuch as these data include the results of every heat so tested, and inasmuch as the errors could not by any chance always support any single theory, we may be certain that the unanimons testimony of the experiments indicates a valid conclusion.

Jan 1, 1886

By A. D. David

The object of this paper is to reduce to the simplest possiblc discussion the recent developments in refinery technology without resorting to detailed technical descriptions of the various items. During the year 1929, the most noteworthy tendencies have been towards the installation of more flexible plants, more unified operations, more balanced performance and greater fuel economy. In no other year in the history of petroleum refining has the industry witnessed to as great a degree the crystallization of so rnany developments in almost every phase of the art. Economic pressure has been the controlling factor, supplemented however by a market demand for more volatile anti-knock gasoline and higher quality of lubricating oils, resulting from the extended use of high-compression motors. Catalytic Hydrogenation Possibly the outstanding achievement during the year has been the beginning of construction of plants by the Standard Oil Co. of New Jersey for the catalytic hydrogenation of the so-called heavier and inferior petroleum oils to produce therefrom not only high yields of anti-knock gasoline, but also lubricating oils equal in quality to the best grades obtainable. It is reported that the plants will operate at a pressure of 4000 lb. or higher and temperatures in excess of 900" F. will be used. The hydrogen required for the conversion will be produced from refinery gases. This type of processing will doubtless be an important factor in balancing future operations; in other words, it can be used to eliminate present waste products and permit production of high-grade products from low-grade crude. Improvements in Lubricating Oils Another important development during the past year has been the extended use of vacuum stills, making possible the production of lubricating oils from what was formerly classed as "fuel-oil crude," or crude from

Jan 1, 1930

By Eckley B. Coxe

SINCE our last meeting, the Institute has lost, by the death of Mr. Gowen, one of its most distinguished members. I shall only attempt in this place to give a brief account of his many accomplishments and achievements; but our records would certainly be incomplete without a recognition of the important influence which he exerted upon the mining and metallurgical industries of this country, and a testimony to his private virtues of character. Although Mr. Gowen was best known as a great lawyer and as the head of a great railway corporation, he began his career, before he was of age, as the manager of a small anthracite blast-furnace at Shamokin, Northumberland County, Pennsylvania. He left this position, to engage on his own account in the mining of anthracite coal at Mt. Laffee, near Pottsville. This proved an unprofitable business, and, after the panic of 1857, he began the study of the law. As soon as he was admitted to the bar, he at once entered upon the active practice of his profession, and soon achieved an extraordinary success. In 1869 he was made President of the Philadelphia and Reading Railroad Company, and he afterwards organized the Pliladelphia and Reading Coal and Iron Company, the largest coalmining corporation in the world. He became a member of. this Institute during the first year after its organization, and remained a member until his death. He always took a deep interest in the work, and was prompt to co-operate by all means in his power in furthering the objects of the Institute. Mr. Gowen was one of the first to recognize the great importance to both miner and consumer, of the proper utilization of the small

Jan 1, 1890

By B. F. Fackenthal

For the past year we have had in use at the Durham furnace a set of hollow pig-patterns made of iron, which have given such satis factory results that I think a description of them would be of interest to the members of the Institute. Before the introduction of these iron patterns, we used the ordi nary wooden patterns, made in the usual way with straps of iron along the sides to protect the corners from wearing off. The size and shape of these wooden patterns are shown in Fig. 1. When the patterns were new, the pigs weighed about 130 pounds each, and were uniform in size, and the moulding was clean. But constant use soon wore the patterns away; and at the end of a few months, the pigs had become, in consequence, so much lighter that the moulding, daily, of several additional beds was necessary to accommodate the same quantity of iron. As the patterns wear away, the moulding becomes ragged and the pigs rough. Moreover, wooden patterns are often destroyed by fire. I have known an entire set to be destroyed by a break-out of iron. The iron pattern which I have designed is free from all the objections to the wooden pattern, being not only more durable, but, in the long run, far cheaper. The iron pattern having the same shape and size as the wooden one, is made of the best flange-iron, of No. 13 gauge. After the sheets have been cut to the proper size, three heats are required for the flanging. At the first heat, each piece is stamped in a cast-iron form, which gives the proper shape to the bottom part of the pat-

Jan 1, 1889

Members whose deaths were reported from Apr 9, 1921 to Apr 7, 1923 Elected Died 1876 ABADIE, E R. 1923 1906 ADAMS, ARTHUR K 1920 1902 AHLES, ROBERT L 1921 1876 Akerman, Richard 0000 1884 ALEXANDER, CURTIS 1921 1918 ALLEN, CARL A 1923 1880 ALMY, WILLIAM F 0000 1893 AMSDEN, 0. B 1923 1917 ARGALL, P. H 1922 1917 ARNOLD, E C 1921 1914 ASANO, K 1921 1920 AUGUSTINE, ALBERT BEARSS 1922 1906 BAIRD, GEORGE A 1921 1921 BALDWIN, GEORGE P 1922 1920 BASKERVILLE, CHARLES 1922 1915 BENSEL, J A 1922 1890 BENSON, A J 0000 1912 BEST, WILLIAM NEWTON 1922 1892 BILHARZ, OSCAR M 1923 1890 BLACKSTONE, RICHARD 1922 1921 BLOOM, GEORGE BARNETT 1921 1905 BOSTWICK, WILLIAM A 1922 1884 BRANNER, JOHN C 1922 1920 BRIDGE, SAMUEL D JR 1921 1893 BROWNE, ARTHUR, 1922 1871 BUCK, STUART M 1921 1897 BURGER, C C 1922 1882 BURT, CHARLES S 1921 1921 BUTZ, Louis N 1922 1917 CAMPBELL, DONALD G 1921 1915 CAPLES, JAMES WATTS 1919 1892 CARLETON, JAMES G 1922 1914 CARUTHERS, A WAYNE 1922 1911 CHASE, FRED M 1921 1892 CLEMENT, F H 1922 1922 COAN, WALTER ERLING 1923 1872 COGSWELL, WILLIAM B 1921 1881 COLVIN, VERPLANCK 1920 1882 COOLIDGE, WALTER G 1922 1907 CORKILL, FREDERICK 1922 1912 COX, Guy H 1922 1883 CUNNINGHAM, JAMES S 1921 1873 DAGGETT, ELLSWORTH 1923 1916 DAULTON, THEODORE M 1921 1888 DICKERMAN, ALTON L 1921 1902 DIEFFENBACH, H M 1921 1911 DUNSTAN, SIMON P 1920 1917 DYNAN, ALAN E 1922 1920 EASTWICK, THOMAS H A 1922 1876 EDWARDS, J WARNER 1921 1914 ELDER, ROBERT B 1923 1885 EMMONS, ARTHUR B 1922 1911 ENGEL, GEORGE W 1920 1887 FERNOW, B E 1923 1879 FIRMSTONE, H1922

Jan 1, 1923

By Otto F. Pfordte

The great advance of the last twenty years in the specialization, delicacy and efficiency of ore-concentrating apparatus calls for a finer system of testing both the qualities of ores and the operations of machines in this department. In amalgamation, lixiviation and smelting, the daily employment of physical and chemical tests has been recognized as necessary, and the cost of the necessary laboratories and employees is cheerfully paid. But while much progress has been made in concentration (due, in a large degree, to the study of the subject in our technical schools), it is still too common in actual practice to follow the loose old method of roughly estimating, once for all, that a given ore " concentrates x tons into one," and resting on this assumption so long as that ore continues to be treated, while assays of the tailings from concentration are made from time to time, without exact determination of their quantity. The first step toward accuracy of control must be a more frequent and precise measurement of the quantity of concentrates from a given operation. This should be expressed in pounds per unit of one ton; and the variations shown in frequent determinations will furnish a constant check upon the character of the ore and the performance of the apparatus. But this is only a part of what should be constantly and systematically done to insure the best work upon a material which must vary continually, even though it come from one mine only. If, in any mill, appropriate laboratory-tests were made at least once a week, the labor and expense involved would be amply repaid by increased knowledge and control of the current operations. A small testing-laboratory, provided with a few gold-pans;

Jan 1, 1902