Search Documents

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult's law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult's law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.' One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys' revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult's law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.' Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.' This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By S. G. Gibbs, A. B. Neely

Jan 1, 1967

By R. H. Adams, A. M. Khan

The Huntington Beach oil field is on the Pacific Coast, southeast of the City of Los Angeles (Fig. 1). It lies both onshore and offshore. Most of the onshore section is operated by Standard Oil Co. of California, WOI. The Tar reservoir is of upper Pliocene age, about 200 ft thick, and consists principally of fine-grained, unconsolidated, somewhat shaly sand, with thin inter-bedded shale stringers throughout (Fig. 2). The reservoir is a broad, highly faulted, elongated anticline, with an areal extent of about 370 acres. Most of the faults bisecting the structure are normal, trend north-south, and are the main cause of reservoir discontinuity (Figs. 3 and 4). From 1964 to Dec., 1967, 259 steam stimulations were performed on a total of 125 Tar sand wells. Eighty-six new wells were drilled and steam stimulated. Of the total, 96 have been stimulated twice, 34 three times and 3 four times. During this same period, a two-injector steam drive pilot has been in progress. The response obtained from this project has been compared with the response to cyclic stimulation. This paper presents an analysis of the field observations for the two methods of thermal recovery. History of Development Drilling to the Tar pool commenced in 1924 with an initial well production of 40 to 50 B/D of 12o API gravity oil. Complete primary development of the pool has been spread over several years. Approxi- mately 40 wells were drilled during the first phase of development, which was completed in 1945. The subsequent primary development started in 1960 with initial well productions of 30 to 40 B/D oil. Thirty-seven wells were completed in the Tar pool during this phase. For the most part, slotted, gravel flow packed liners have been used in the wells in this pool. A cyclic steam stimulation pilot was initiated in March, 1964. Based on the very successful stimulation in the pilot area, the cyclic stimulation project was expanded to include all of the Tar pool wells producing at the end of 1965 (Fig. 5). Also, a development drilling program was begun at this time. To date, 86 new wells have been drilled under this program. The number of wells drilled each year in this secondary phase of development is also shown in Fig. 5. New Well Completion Practices Most of the new wells have been completed to produce from both the Upper and Lower Tar zones. Generally, a casing stub is cemented from the top of Lower Tar to the base of clean Upper Tar sands to exclude intermediate water-bearing sands. The water string is then cemented from the top of Upper Tar to about 1,500 ft with neat cement and 30 percent silica flour. The annulus from 1,500 ft to surface is then filled with a petroleum-based gel through a high-temperature port collar. Once again, a history of sand-free production dictated the use of 60-mesh gravel flow packed liners. The Upper and Lower Tar

Jan 1, 1970

By J. B. Clark

In multiphase ternary diffusion studies, plots of the variation bf the composition on the isotherm constitutes one of the most effective methods of presenting experimental results, especially if such plots are made in a manner which relates the composition path on the isotherm with the diffusion layer structure in the couple. Unfortunately, if different conventions for plotting are used serious misinterpretations occur readily, causing apparent disagreement between investigators who actually share the same viewpoint. A common convention for mapping these diffusion paths is needed at this time because with the increasing use of the electron-probe X-ray microanalyzer, a much greater number of ternary diffusion studies can be expected in the near future. In an effort to prevent unnecessary confusion in the future litera- ture, a convention for these plots is proposed, as outlined below. A hypothetical example of the use of these conventions is given in Fig. 1 where the path of composition through the diffusion structure of the 100 pct A/50 pct B, 50 pct C couple is plotted on the appropriate isotherm of the ABC system. The lower case letters relate the region in the diffusion layer structure to the appropriate composition on the ternary isotherm. 1) The diffusion path is plotted on the isothermal section corresponding to the diffusion temperature of the couple. 2) The terminal compositions of the plotted diffusion path are the initial compositions of the couple halves—provided infinite boundary conditions are maintained. If, in either couple half, infinite conditions are not maintained, then the path terminates at the composition of the exterior surface of the couple. If, at this surface, the composition varies with time or if the plotted path is time dependent, then the diffusion time should be noted beside the plotted path. 3) A solid line crossing a single phase field (e.g., line a-b in Fig. 1) denotes an existing layer of that phase in the diffused couple. 4) A dashed line crossing a two-phase field parallel to the tie lines (e.g., line g-h) represents an interface between the two phases with interfacial compositions designated by the ends of the tie-line. The line represents no spatial extent. 5) A solid line crossing a two-phase field so as to cut tie lines (e.g., line b-c or line j-k) represents a locally equilibrated columnar two-phase layer. The solid line should cut those tie lines which correspond to the lateral interfacial equilibria along the columnar

Jan 1, 1963

[ ]

Jan 1, 1938

By Cyril Wells, Paul E. Busby, Donald P. Hart

EARLY workers in the field have established that the diffusion of nitrogen follows normal diffusion laws. Concentration-penetration data from layer analyses of reasonably pure iron specimens nitrided in an atmosphere of CO-NH, are given in the literature,' and were utilized to calculate diffusion constants for nitrogen. The diffusion of nitrogen in y-iron may be represented approximately by the equation D - 1.07x10-' e-:".'m'"'r The diflusion coefficients, D, given by this relation represent mean values, since carburization occurred simultaneously with nitriding. The rate of diffusion in a-iron has been determined from calculations based on data obtained by measuring the internal friction of samples at each of several frequencies and temperatures.' The expression for the diffusion of nitrogen in a-iron derived from these experiments is D= 1.4x10-1 e-it tudent Increasing carbon content decreases the diffusion of nitrogen in a-iron.3 Oxygen, either dissolved or combined, has been shown' to exert a marked influence on the diffusion of nitrogen from a nitriding atmosphere. D values increase rapidly with increasing amount of dissolved oxide in the metal, but diffusion is completely inhibited if preliminary oxidation has produced the slightest trace of iron oxide on the surface. Diffusion coefficients have also been calculated from permeability and solubility data,' but these values are of questionable accuracy since the boundary conditions assumed may not actually exist. Experimental Method The method selected for determining the diffusion coefficient of nitrogen in a-iron in the present investigation was the so-called fractional saturation method. This method consists of heating the specimen in an atmosphere of H2-NH8 mixtures of known composition for a predetermined time. Following this treatment, the specimen is analyzed for nitrogen; and the diffusion coefficient is calculated from a known relationship of the fractional saturation, time of diffusion, and dimensions of the specimen. This relation is based on a solution of Fick's second law and assumes that the surface of the specimen immediately reaches a given concentration which remains constant during the diffusion anneal. Tabular solutions are available4-5 and provide the relationship between fractional saturation and the quantity \/Dt /a, where D is the diffusion coefficient in cm2 per sec, t is the time of the diffusion anneal in seconds, and a, in the present experiments, is the half-thickness of the slab specimen in cm. The method is adequately discussed elsewhere.9-10 Material The material for this study consisted of 3/32 in. thick (0.24 cm) carbonyl iron plate. The major impurities in this iron are oxygen and carbon, which are readily removed by long time high temperature treatment in an atmosphere of purified hydrogen. In order to reduce the diffusion anneal time for saturation runs, some of this material was rolled to a thickness of 0.015 in. (0.038 cm) prior to the hydrogen treatment. Hydrogen treatments were carried out in a hydrogen-purified Armco iron tube heated in a global

Jan 1, 1957

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard's and Dundrova's theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.' In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By Curtis Wilson

FROM the results of his investigation of the hardenable copper-nickel-silicon and copper-cobalt-silicon alloys, M. G. Corson1 explained the dispersion-hardening effect by assuming the precipitation of the inter-metallic compounds nickel silicide and cobalt silicide, and on this basis he constructed diagrams for the pseudobinary systems copper-nickel silicide and copper-cobalt silicide. A consideration of these diagrams and of the factors that exert such an important influence upon the rate of precipitation, such as degree of supersaturation, nucleus number and rate of diffusion, leads to the expectation that the rate of precipitation of the silicides on reheating the quenched solid solutions at temperatures below the alpha-phase boundary should increase continuously as the reheating temperature is raised. The present investigation shows that while this rate does increase with the reheating temperature in a general way, it does not do so continuously. Supplements to Corson's diagrams are offered, showing the discontinuities, and slight modifications in the solubility curves are suggested.

Jan 1, 1933

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By Stanley J. LeFond

Brazil is one of the most outstanding examples of economic development of our time. Its amazing growth record is substantiated by a GNP which has increased at an average rate of 92% for the period 1968-1970 and estimates for 1971 range from 11.7-12.5%. Hence, this growth, coupled with a more relaxed attitude of the Brazilian government towards foreign participation in business opportunities and the remittance of profits out of the country, has caused many exploration companies to reevaluate the potential of Brazil. Despite recent press notices and publicity, Brazil is still not a mining country in the tradition of Canada or Australia. It is still basically an agriculture and manufacturing country.

Jan 11, 1973

By C. M. Young

THE following paper has been prepared with the object of placing on record in the Transactions some facts concerning the present condition and future prospects of the coal industry of Illinois. In presenting it, the writer wishes to say that a considerable amount of the material contained is taken from the publications and records of the Illinois Coal Mining Investigations, the annual Coal Report of the State Mining Board, and the work of the State Geological Survey. Coal Beds and Mining Methods According to the latest maps of the State Geological Survey, there are only 19 of the 102 counties of the State some portion of whose territory is not within the borders of the coal measures. If outlying areas in Calhoun and Whiteside Counties are considered, the number is reduced to 17. This does not mean that all of the 85 counties that are partly or wholly underlain by coal measures will become producers, as there are some portions of the State in which the coal does not occur in beds of such thickness as to warrant the hope that it can be mined. The mining of coal is widespread, however, for in 1916 there was production from 51 of the 102 counties of the State. There seem to be no cases in which operations will be limited by depth, as none of the coal measures lie at depths much greater than those at which it has been proved that coal may be profitably mined in this field. In fact, the deepest shaft reaching a bed of bituminous coal in the United States is located in this State at Assumption, where coal only 3 ½ ft. (1.07 m.) thick is worked at a depth of 1004 ft.. (306 m.) The coal beds occur in the form of a basin which is deepest along a line extending through the central part of the State and bearing a, little west of north. The northern, western and southern borders of this basin lie within the boundaries of the State, but on the eastern side the Illinois field is continuous with the Indiana field. The glacial drift covers all except the extreme southern end of the State and the visible outcropping

Jan 9, 1917

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957