Search Documents

By J. J. Frawley, W. J. Childs

PREVIOUS studies have shown that if a supercooled liquid metal was perturbed by vibration the probability of nucleation is is During a recent investi- gation to determine quantitatively the amount of energy needed to cause nucleation in a given supercooled liquid specimen, it was found that at low-energy values in the megacycle range, below the threshold energy value for cavitation, the amount of dynamic supercooling was greater than the amount of static supercooling. That is, if a specimen had a given amount of thermal supercooling under static conditions, its thermal supercooling could be increased by the addition of low-energy sound waves. The material used in this investigation was high-purity bismuth. This material was chosen because of its low melting point and the high degree of supercooling which could be easily obtained. The sound gener- ator employed in this work was a commercially built Sperry ultrasonic testing unit. This unit was equipped with a barium titanate crystal as a piezoelectric transducer. These sound waves were transmitted to the supercooled melt by a Pyrex rod, as shown in Fig. 1. The transducer was coupled to this Pyrex rod wave carrier by motor oil. The Pyrex wave carrier was approximately 1.5 ft long to prevent damage to the transducer by heat. The diameter of the Pyrex wave carrier appears to be critical. In the initial tests a wave carrier of 0.5 in. in diam was employed. However, the sound waves had no effect on the amount of dynamic supercooling. When the diameter of the wave carrier was increased to approximately the inside diameter of the Pyrex crucible, the sound waves were more effective. Approximately 200 g of metal was melted under a stannous chloride flux in a 30-ml beaker by induction heating. The temperature was recorded by a Pyrex-encapsulated chromel-alumel thermocoule which was placed in the beaker after the bismuth melted. The Pyrex wave carrier was immersed slightly below the surface of the liquid bismuth and the specimen was reheated to about 500°C. It was observed that the amount of supercooling depends on the amount of superheating the specimen receives; therefore, for meaningful results the amount of superheating was the same for all heating cycles. The specimen was allowed to cool in air and the change in temperature was continuously monitored with a potentiometric strip-chart recorder.

Jan 1, 1969

By R. G. Davies

WeERTMANI has shown that the high temperature steady state creep rate, i, in lead and indium-base alloys obeys an equation of the form where AH is the activation energy, o the applied stress, n the stress exponent, and R and T have their usual meanings. He observed a variation in n from 4.5 for pure metals to 3 for concentrated alloys, which he interpreted as due to Change in creep mechanism from the climb of dislocations in pure metals to a micro-creep mechanism in the alloys. The Cottrell-Jaswon microcreep mechanism of the moving dislocation taking its impurity atmosphere with it was considered to be the most likely process, although short-range order and the segregation of solute atoms to a stacking fault will also give a stress exponent of 3. Steady state creep has been investigated in a Au - 27 at. pct Cu alloy at temperatures above 1/2 TIM where TIM the absolute melting temperature. As the oxidation resistance of this alloy is excellent all tests were carried out in air with a furnace built to give a temperature variation of less than 1°C along the 60 mm gage length. A lever-arm arrangement applied the stress with a load being adjusted between each creep test to maintain a constant stress. As each test produced less than 0.5 pct creep strain, the variation in stress during the test was negligible. The creep strain was measured by a transducer at the end of one of the alloy-steel grips, with the out of balance potential being finally recorded on a variable speed chart recorder. A typical creep curve is shown in Fig. 1. The results, Fig. 2, confirm that n is nearer to 3 than to 4.5; the creep mechanism could be any of those given above. The activation energy, AH, which is independent of stress, is consistent with a diffusion controlled process; the activation energies for the self-diffusion of gold and for the diffusion of gold into Copper are both -45 kcal per ml., There is now considerable evidence, that, when the steady state creep is dependent upon diffusion, irrespective of the actual creep mechanism, the activation energy is independent of the stress. The author would like to acknowledge the financial assistance provided by the International Atomic Energy Agency, Vienna, and the Argentine Atomic Energy Commission.

Jan 1, 1962

By Enid C. Plante

To extend our knowledge of the flotation behavior of sulphide minerals, the response of the following minerals to ethyl xanthate as collector was studied by captive bubble and cylinder flotation tests: antimonite (Sb2S3), arsenopyrite (FeAsS), covellite (CuS), rnarcasite (FeS2), orpiment (As&.), pyrrhotite (FeS) and tetrahedrite (4CU2S, Sb2S3). Lollingite (FeAs2) was also exarnined to determine if its behavior could be correlated with that of pyrite or rnarcasite (FeS2. Experimental Method Mineral for Flolation and Contact Tests Mineral was prepared in the manner a1ready described1 and its behavior both freshly ground and "oxidized" was studied. Tests in which the mineral was allowed to oxidize for various periods showed that a uniform response to xanthate was reached in two days or less. Oxidation Products The soluble oxidation products from most of the above minerals were measured and their effect on the flotation of the mineral studied. The mineral samples were wet ground to minus-52 mesh and deslimed, and 20 g of this material placed in 200 ml of distilled water of a measured pH value, and CO2-free air bubbled through each suspension at a constant rate (about I bubble/sec) for 5 days. It has been shown1 that the size of the mineral is unimportant in the rate of formation , oxidation products and that probably the supply of oxygen to the mineral is the rate-determining step. At the end of 5 days the pH value of the 'supernatant liquid was measured again, the mineral filtered off and the soluble products determined. Methods for estimation of sulphur acids, ferrous and ferric iron and copper have already been described.l No satisfactory method was found for antimony. Arsenic was estimated as the arsenate.2 Flotation of "Unoxidized" Minerals with Ethyl Xanthate as Collector Fig I to 3, 4. 6, show the effect of alkali and cyanide as depressants for the minerals with 25 mg potassium ethyl xanthate per liter as collector at 35°C. Wark and Cox8 have shown that with ethyl xanthate as collector, galena, pyrite and chalcopyrite show a greater tolerance to cyanide and hydroxyl ions at room temperature than at 35°C Covellite (Fig I), marcasite (Fig 2) and pyrrhotite (Fig 3) behave similarly. The independence of the curves for pyrrhotite at 35°C with respect to cyanide

Jan 1, 1949

By David J. Mack

A survey and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CalculatioX oP YouNg's Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess'enden4',~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

There were two official representatives of Foreign Governments as guests at the Chicago Meeting. One was Frederick Goransson, managing director of the Saudvikens Steel Works, who represented the Jernkonteret, the Iron and Steel In-stitute of Sweden, and who came to this country especially for our meeting. The other distinguished guest was Commander Toublet, who repre-sented the French Embassy. Commander Toublet delivered a most polished address at the Banquet, dealing with the felicitous relations existing between this country and France for the last 150 years. Com-mander Toublet was accompanied by Mrs. Toublet, who won the hearts of all the ladies present, whose guest she was.

Jan 11, 1919

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By John C. Long

The advantages of firebrick regenerative hot-blast ovens being thoroughly appreciated by those engaged in modern blast-furnace practice, the important question now is to obtain the best and most efficient apparatus. The apparatus invented by the writer, and described in this

Jan 1, 1885

By E. Peters

As in other fields of Extractive Metallurgy, Hydrometallurgy is preoccupied with separation processes and with oxidation-reduction processes. The physical chemistry of each type of process can be described in terms of thermodynamic equilibria and in terms of reaction kinetics. Reaction kinetics are much more important at the low temperatures limiting hydrometallurgical processes than in com- parable pyrometallurgical operations and the number of cases in which the kinetics can be described by simple liquid-phase mass-transfer models are sharply limited. It is convenient to subdivide the applicable rate phenomena into processes in which (a) interface reactions control the rate,(b) mass transfer processes control the rate, (c) solid state process affect the rate, (d) thermodynamically predicted phase changes or molecular reactions fail to take place, (d) metastable substances or supersaturated phases persist, and (elchomogeneous reactions in solution affect the chemistry and the kinetics. Examples are drawn from the unit steps of leaching, cementation, hydrogen reduction, and electrowinning.

Jan 1, 1973

By Kent W. Pilz

Wet dust suppression can be achieved by 1) confinement of the dust within the dust producing area with a curtain of moisture, 2) wetting of the dust by direct contact between the particles and droplets of moisture or 3) the formation of agglomerates too heavy to remain airborne, or too heavy to become airborne, by combining small dust particles with each other and with the droplets of liquid. From the standpoint of economy, availability and safety, water is the ideal fluid; however, it is not as effective for dust suppression as when small percentages of specially formulated dust control compounds are blended with it. Performance of dust control com pounds is related to surface active agents and surface activity. In all liquids there is an attractive force between molecules which varies inversely as the sixth power of the distance between molecules. Thus, in the liquid phase where molecules are crowded together, the intermolecular forces are powerful; whereas in the liquid-vapor phase where the molecules are relatively far apart, these forces diminish rapidly. In the body of a fluid there is an uneven distribution of forces resulting in an inward pull called surface tension. The force which keeps two surfaces apart or causes them to coalesce is termed interfacial tension. Fluids of high surface tension exhibit poor wetting, spreading and penetrating qualities. Water has the unusually high surface tension of 72.75 dynes per cm at 20°C.

Jan 7, 1972

By Edward L. Vickers

The Pacific rim countries, comprising more than half the globe, represent a complex mix of developed and developing nations. The area comprises a large segment of the industrialized world. Within its boundaries are also found many of the world's greatest mineral resources largely concentrated in the less developed countries. The conflicting objectives of these developed and developing nations are giving rise to changes in the traditional patterns of world resource development. Powerful political and socio-economic factors affecting the world today are having a great bearing on natural resource developments in the Pacific basin. New forms of partnerships have been emerging in developing nations which have had a great impact on the mining com- munity, lending institutions, as well as political relations. The United States and Japan have been substantially responsible in the past for the development of natural resources in this area of the world. Their role, however, is undergoing significant metamorphosis. The rapidly changing economic and social environment in the developing countries is producing new tensions which affect future collaboration between producers and users of natural resources. To understand current problems, I believe, it is worthwhile to examine historical trends in this area which may help defining alternatives facing us in the future. In modern times the United States was the first country in the Pacific basin to start development of resources on a massive scale. It began with the major exploration of the mineral-rich west of the United States and extended significantly later into Latin America and Australia. In the early 1950's, Japan became a significant

Jan 1, 1976

By Arthur L. Walker

In June, 1893, while I was with the Old Dominion Copper Co. at Globe, Ariz., I received an offer to take charge, as manager, of the Baltimore Electric? Refining Co. which had recently built a plant at Baltimore, Md., having a capacity of about 1200 tons of electrolytic copper per month, using the Hayden series system. This was a very large output, for in those days the plants were small and the art was in its infancy. At the beginning of 1893 there were 11 electrolytic refineries in the United States, most of them using the multiple system. The Hayden series system was used at Baltimore and Bridgeport and the Smith series system was in operation at the Electrolytic Copper Co. at Ansonia, COM., and at the Pennsylvania Salt Co. at Philadelphia. In the latter system the plates were placed in a horizontal position, but the operating difficulties were so numerous it was soon discarded. The total production of these 11 plants in 1892 was very small; I have not been able to discover reliable figures of production. There were about thirty electrolytic copper refineries in the world that year, according to Titus Ulke, and the entire production of these

Jan 1, 1932

By J. J. Rutledge

FULLY 60 per cent of the serious and fatal accidents in Maryland coal mines are due to falls of roof and side. Usually, the victim of the fall sustains a broken back, sometimes not only the vertebrae being fractured but the spinal cord also being severed. When the spinal cord has not been severed and yet the vertebrae have been broken or injured, it is often possible to rehabilitate the victim of the broken back. - Such accidents are classed as Permanent Total and the victim receives a certain compensation from the State Industrial Accident Commission; sometimes the amount is awarded in a lump sum, but usually it is paid weekly. When the amount allotted to the victim of such an accident has been expended, either in a lump sum or weekly payments, the victim of the accident is dependent on public charity. Some efforts have been made to physically rehabilitate the victims and make them at least partly self-supporting before the expiration of their compensation payments. The State Industrial Accident Com-mission has done some of this rehabilitation. The Maryland Bureau of Mines, in cooperation with R. C. Thompson, Supervisor of Vocational Rehabilitation, State Department of Education, and his assistants, has, through an informal cooperative arrangement, placed several of the victims in hospitals in Baltimore for treatment. Six years ago, through the efforts of the Maryland Bureau of Mines, a dozen or more broken-back victims were examined by an orthopedic surgeon and report was made to the Bureau regarding such cases and the possibility of their rehabilitation. This paper details the result of such examinations.

Jan 1, 1936

By W. R. Ingalls

THE bases of the work by the committee whereof I am chairman were (1) the abolition of extra-lateral rights and (2) the preservation of the maximum of the existing laws. The matter of extra-lateral rights had been under prolonged discussion among mining men and up to the time when our com-mittee began its work (in 1917) the expression of opinion in every way whereby it could be made known -and those ways were extensive-was only a little short of being unanimous that extralateral rights ought to be abolished. I have not observed important evidence indicating a change of opinion on the subject since 1917. ABOLITION OF DISCOVERY LOGICAL Now, when it be decided that extralateral rights ought to be abolished, there can not be merely a simple change to that effect, but it is found that consequential changes are necessary all the way through the existing laws. Abolition of extralateral rights implies abolition of discovery as a prerequisite to location, for otherwise there would be no legal means for locating claims on the dip of a vein. Quite apart from this consideration, abolition of discovery as a prerequisite to location is supported by other good reasons. Among these are the occurrence of orebodies with no exposure on the surface and which often are hidden at great depth. A prospector who has reason to suspect the occurrence of such an orebody must have legal means for the location of a claim within which to explore, and obviously he may. not be able to make any discovery on the surface sufficient to locate and hold legally such a claim under the terms of the law as it stands at present. As a matter of fact, discovery as a prerequisite to location was abolished by common consent many years ago, not only for the reasons that I have given here-inbefore but also for others. It is highly desirable to revise the mining law in this respect, so that it will conform to the conditions of practice and not require people to perjure themselves in making locations, even if it be for praiseworthy purposes.

Jan 6, 1922

By P. G. Shewmon, W. M. Robertson

The derivative of the surface tension with orientation, ??/??, for copper has been measured over the entire unit triangle. This derivative or torque term was determined from the variation of the dihedral angles at the intersection of twin boundaries and free surfaces. High-temperature anneals in graphite with a hydrogen atmosphere gave torque terms of 0.097 at (111), 0.066 at (100), and 0.0257 at (110). A variation from -36oto +23oC in the dew Point of the H2 had no effect on these values, nor did a change from 99.98 to 99.999 pct Pure copper. The removal of graphite from the system decreased ??/?? slightly. Considering the surface near a low-index plane to be smooth except for occasional steps, the free-energy increment per cm of step is calculated, and it is shown that the observed variation of ??/?? is consistent with a random distribution of steps and an interaction energy between steps. Integration of ??/?? gave the relative values of y at (100), (110), and (111) as comPared to ymax: (Y111/Ymax) =0.974, (Y110/Ymax) =0.996, (y100/Ymax) = 0.983. The ratio of the surface tension of coherent twin boundaries to the surface tension of the free surface was found to be (yT/ys) = 0.027 * 0.011. In a crystalline solid the surface tension y (surface free energy per unit area) depends on the orientation of the surface relative to the crystallographic axes of the crystal. Measurements of this variation of y with surface orientation have been reported for metals only within the last few years. Consider the grain boundary groove shown in Fig. 1. Here the three surfaces are all normal to the plane of the paper, and each has a different surface tension, y1, y2, and y3. If the system is at equilibrium, the total surface free energy must remain unchanged for a slight vertical displacement of the intersection (points A, B, and C are kept fixed). As shown by Herring,' the following equation is obtained:

Jan 1, 1962

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

I. MCLAUGHLIN, R. P.-Protecting California Oil Fields from Damage by Infiltrating Water. Discussed by M. E. Lombardi, A. F. L. Bell, A. C. McLaughlin, R. P. McLaughlin, William A. Williams, Mark L. Requa, C. D. Keen 2413 BEST, W. N.-Petroleum as Fuel Under Boilers and in Furnaces. Discussed by William A. Williams, Hennen Jennings, David T. Day, Mark L. Requa, A. F. L. Bell, W. N. Best 2420 JOHNSON, ROSWELL H.-Sliding Royalties for Oil and Gas Wells. Discussed by William A. Williams, A. C. McLaughlin, A. F. L. Bell, Roswell H. Johnson 2423 BELL, ARTHUR F. L.-Important Topping Plants of California. Discussed by William A. Williams, David T. Day, A. F. L. Bell 2426 LOMBARDI, M. E.-The Cost of Maintaining Production in California Oil Fields. Discussed by C. D. Keen, Mark L. Requa, H. M. Bacon, M. E. Lombardi 2427 HUNTLEY, L. G.-Oil, Gas, and Water Contents of Dakota Sand in Canada and United States, Discussed by E. W. Shaw 2428

Jan 12, 1915

By E. W. Lithgow, E. G. Williams, R. R. Holbrook, B. R. Wilson

The mineralogy and geochemistry of Pennsylvanian shales and underclays were studied to determine their suitability for lightweight aggregate and refractory ladle brick. Eighty percent of the variation in bloating of shales and clays was explained by the variation of Si02, A1203, and fluxes (Fe203, MgO, CaO, Na20, and K20); 60% by variation in quartz, kaolinite, illite, and chlorite. The best bloating was exhibited by marine shales, whereas freshwater shales and underclays experienced little or no expansion. Regional paleogeographic maps o f Pottsville and Allegheny shales permit bloating to be geographically predicted. It was found that clays meeting the specifications for refractory ladle bricks were obtained from underclays having over 34.5% mica, over 40% kaolinite and less than 15% quartz. Underclays of this composition are confined to the lower Allegheney outcropping along the near-margins of the coal basin. The best clay is that underlying the Lower Kittanning coal. Porosity of the first fired brick was found to be inversely correlated with reheat expansion.

Jan 1, 1975

By D. Geiselman, A. G. Guy

Single cvystals were grown from high-purity magnesium containing known amounts of nitvogen in the range 0.0008 to 0.0048 wt pet. Crystals of known ovientation were tested in tension in an Instron ma chine to determine the yield strength and to obsevue wheather a yield point occurred. Slowly cooled crystals or those given a solution heat treatment did not show a yield point. However, crystals that were aged following a solution treatment showed a yield point for all of the nitrogen contents studied. It was concluded that nitrogen caused the yield point by the Cottrell mechanism. NITROGEN has been shown to produce sharp yield points in single crystals of cadmium, zinc,2'3 ß-brass,4 and iron,5,6 as well as in polycrystalline iron7 and molybdenum.8,9 Since magnesium has a structure similar to zinc and cadmium, it seemed reasonable that magnesium should also exhibit a sharp yield point provided it contained sufficient nitrogen. Bobalek and Shrader10 reported a total nitrogen content of 0.002 to 0.0065 wt pct in com- mercial magnesium alloys, an amount well in excess of that required by theory. However. magnesium differs from cadmium and zinc in that it forms a stable nitride, Mg3N2, which has a standard free energy of formation of -95,480 cal per mole at 25" c." If rather than being in solid solution, the nitrogen were predominantly combined as the nitride, it could not act to produce a yield point. This type of behavior is the basis for the elimination of strain aging and a yield point in steel by the addition of strong nitride formers such as titanium,12 columbium,13 aluminum,14 vanadium,15 and boron.16,17 Thus, there appeared to be factors both favorable and unfavorable to the production by nitrogen of a sharp yield point in magnesium, and the purpose of this investigation was to determine the actual behavior of magnesium crystals containing known amounts of nitrogen.

Jan 1, 1960

By WILLIAM WATERS

L HISTORY. THE Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively recent date, were carried out in the neighborhood of the vil¬lage of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E-W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposed to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Nov 1, 1908

By R. I. Jaffee, F. C. Holden, H. R. Ogden

ECENT papers dealing with the properties of unalloyed iodide titanium have been directed primarily at the determination of base-line properties for alloy investigations. Early work was limited to a few tests because of the limited availability of iodide titanium at the time. In the results of papers by Campbell et al.,1 Gonser and Litton,2 Jaffee and Campbell,3 inlay and Snyder,4 and Jaffee, Ogden, and Maykuth, data on mechanical properties are presented for unalloyed iodide titanium in the annealed and cold-worked conditions. Data are presented in this paper which show the effects of heat treatment on the structure and mechanical properties of commercially produced iodide titanium. Correlation is made between microstruc-tural variables and the mechanical properties. Experimental Procedures Melting Stock: The melting stock used was as-deposited iodide titanium, produced by New Jersey Zinc Co. The furnished analysis showed the following range of impurities: N, 0.004 to 0.008 pct; Mn, 0.005 to 0.013; Fe, 0.0035 to 0.025; Al, 0.013 to 0.015; Mo, 0.0015; Pb, 0.0045 to 0.0065; Cu, 0.0015 to 0.002; Sn, 0.001 to 0.01; Mg, 0.0015 to 0.002; and Ni, 0.003. Hydrogen content as determined by vacuum-fusion analysis was 0.0091 wt pct (0.44 atomic pct) after arc melting and fabrication. Nitrogen analysis on the arc-melted and fabricated titanium showed a content of less than 0.002 pct N. The average hardness of the furnished stock was Rf 70, or approximately 85 VHN. Melting Procedure: The as-deposited rods were rolled, sheared, and degreased in preparation for arc melting. The charge was arc-melted with a tungsten electrode in a water-cooled copper crucible under a positive pressure of high purity (99.96 pct) argon. The final ingot was approximately 2 in. in diameter and showed no increase in hardness over that of the initial stock. Fabrication: Heating for fabrication was done in air. It was begun by forging the ingot into a 3/4 in. diam rod, at an initial temperature of 1600°F. Scale was removed by sandblasting. The rod was then swaged to 1/4 in. diam at room temperature through a series of 20 dies, with approximately 10 pct reduction in area between each die. An anneal of 1 hr at 850 °C in air was given after the 1/2 in. die, such that the final cold reduction was 75 pct. Sections cut from this rod were used for test and microstructure specimens. Heat Treatment: Heat treatments were carried out in resistance tube furnaces with stainless-steel linings, under an atmosphere of gettered argon. As further protection against contamination, the specimens were packed in titanium turnings in a titanium sleeve. Control experiments have shown negligible hardness increases with this method, indicating that contamination from oxygen and nitrogen is slight. Three cooling rates were employed in this work; these have been designated as water quenching, argon cooling (to simulate air cooling under a controlled atmosphere), and furnace cooling. The cooling rate for an argon cool is 100°C per min for the first minute, with an average cooling rate of 35°C per min over a 15-min period. A furnace cool requires about 10 hr, with an average cooling rate of 3.6oC per min during the first hour, and an average cooling rate of 1.2°C per min over the 10-hr period. Microimpact Test: The specimen adopted was based on the cylindrical Izod Type Y specimen (ASTM, E23-41T). All dimensions were reduced to half scale, including the notch radius. Specifications are shown in Fig. 1. The specimen is held vertically in an adapter and broken as a cantilever beam. Impact tests were run on a constant-velocity (11.34 ft per sec) Tinius Olsen impact testing machine with a total available energy of 100 in.-lb. Tests were made to determine the correlation between this microimpact and the standard V-notch Charpy impact test. Curves showing impact energy as a function of temperature for both impact tests are plotted in Fig. 2. Transition temperatures, when they occur, are about the same for both impact tests. All three titanium-rich materials have the same conversion factor, 10. Tensile Testing: Tensile tests were conducted on Baldwin-Southwark testing machines using the 600, 2400, or 3000 1b range. Specifications for the test specimen were taken from the 1948 edition of the ASM Metals Handbook, and are shown in Fig. 1. Strain measurements were made using an SR-4 resistance gage (Type A-7) cemented to the reduced section in conjunction with a lever-type extenso-meter. Readings on the SR-4 strain indicator were

Jan 1, 1954