Search Documents

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

By J. C. Gerdeen

It is of upmost importance to keep the size of the program to a minimum for the computer being used. One way is to reduce the size of the data bank by adjusting the large common array A in the main program (page, line 32) and the statement following the assignment of A. The current value of A is 35001 and is optimized for the UNIVAC computer with 5,000 words of useable storage. Another way to reduce the required storage is to overlay the program. That is, to have in the computer only the subroutines which are being used. In large finite element codes, overlays or segmentation of the program is a necessity. The code presented here has three levels of segments and are presented graphically in the tree in Figure D-1.

Jan 1, 1976

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

By L. P. James, W. W. Atkinson

Utah has produced about one billion troy oz. (31.7M tonnes) of silver, more than any U.S. state except Idaho. Several very high grade ore systems, now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These Utah mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham porphyry mine has also yielded more byproduct silver than other porphyry copper-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcano sedimentary rocks. Thick permeable latest-Proterozoic basement meta quartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d’Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to porphyritic plutonic rocks.

Jan 1, 2000

By Chester M. F. Peters

The opportunity to make a close study of the available geologic data existing along the line of the California Aqueduct crossing of the Garlock fault in the Tehachapi Mountains was brought about first by my involvement in the prebid examinations, and later with contractors' claim cases. The California Aqueduct crosses through the western end of the Tehachapi Mountains and cuts across the Garlock fault zone at a location about 9 miles east from its junction with the San Andreas fault zone. This is about 65 miles northwest of Los Angeles and 38 miles southeast of Bakersfield (Fig. 1) (1). This map was published after the tunnels were started and shows the corrected geology. At the crossing the fault has north and south branches which extend northeastward for about 22 miles before converging. In the vicinity immediately east of the tunnel line the north branch of the fault starts to converge toward the west. After crossing the line it passes under the upper plate of the apparent easterly extension of the Pastoria thrust fault, so the actual junction with the south branch is obscured. The aqueduct design called for the expected active slip zone of the north Garlock fault branch to be crossed by the 2,800 foot long Pastoria siphon, which connects with the north portal of Tehachapi Tunnel No. 3. The tunnel would extend through the western end of Genghus Ridge which lies between the north branch and the main south Garlock fault zone in Beartrap Canyon. Here again the

Jan 1, 1997

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By J. Vance Batty

The Permian Red Bed copper deposits of the South Central States are a potentially important resource. Only the higher grade, near-surface ores are now exploited because conventional froth flotation does not recover oxidized copper minerals which comprise 10 to 15 percent or more of the copper content of typical ore. Laboratory-scale beneficiation studies were initiated to devise a method capable of recovering both sulfide and oxidized copper mineral. Testing established that the high clay and gypsum content of typical ore prevented effective flotation of the oxide mineral using sulfidizing, fatty-acid, or oil emulsion techniques. A modified leach-precipitation-flotation (L-P-F) procedure recovered over 90 percent of the copper, compared to a recovery of 77 percent obtained by conventional sulfide flotation. The higher costs of the L-P-F method would reduce the increased revenue from higher copper recovery. An increase in copper price and/or an increase in oxide copper content of the ore would make the L-P-F process comparatively more attractive.

Jan 1, 1970

By H. E. Thomas

[The Bureau of Mines has conducted a field hydraulic fracturing experiment to determine the preferential orientation of induced fractures in oil shale at a depth of about 400 feet in the Green River Basin of Wyoming. The hydraulic fracturing treatment was performed by injecting extremely viscous water-base gel and 8- to 12-mesh sand into the oil shale through straddle packers set in an impermeable section of smooth-walled, 6-1/4-inch-diameter open hole. An impression packer proved that a horizontal fracture, which has an average width of about 1/2 inch at the borehole, was induced. A corehole drilled 100 feet from the fractured well intersected the fracture and confirmed its horizontal orientation. Because a horizontal fracture was successfully initi¬ated, it is inferred that the creation of multiple, closely spaced horizontal fractures may be feasible in Green River Basin oil shale.]

Jan 1, 1972

[ ] ALVA L. SMITH RMCMI PRESIDENT 1989-1990 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 86th Regular Meeting and Convention to be held June 24, 25 and 26, 1990 at Sheraton Steamboat Steamboat Springs, Colorado

Jan 1, 1989

By Charles Steed

The design of pillars in room and pillar operations is always a compromise between factor of safety and ore recovery. In actively mined and accessed areas the stability of pillars must be sufficient to support the roof, providing safe working conditions for men and equipment, while optimizing ore recovery. As a reserve is mined out, and if conditions are favourable, pillars are often removed to increase recovery. Considerations for pillar removal include value of the ore, the effect on immediate and overall mine stability and the safety of the mining operations as well as the consequence of disruption of overlying strata and surface infrastructure as the support of the pillars are removed. Many parameters influence pillar strength and the contribution of the pillar to ground support. These include seam height, seam depth, seam inclination, room span, quality of rock, time, etc.. Empirical, analytical and numerical modeling methods are commonly used to optimize pillar sizing and placement and predict influence of pillar extraction or reduction on ground stability. Practical examples for pillar design and optimization in low seam gypsum mining operations and optimizing sequencing of pillar extraction in thick seam metal mining operations are outlined.

Jan 1, 2003

By James M. Spear

The U.S. Bureau of Mines and the U.S. Geological Survey conducted a mineral survey of the Elk Creek RARE II area during the summer of 1981. The study area encompasses 18,900 acres [29.5 sq mi (7,680 ha)] along Elk Creek, 18 mi (30 km) southeast of Covello, California. No mineral resources were identified by the U.S. Bureau of Mines during this survey. Assay results of samples taken in this area indicate only trace amounts of manganese and chromium. No radioactive or fluorescent minerals were detected. No oil and gas, coal, or geothermal leases have been recorded for the study area.

Jan 1, 1982

By George J. Karcas, Raimo Kuusisto, Pertti Pekkala

Ongoing Outokumpu development in Solvent Extraction and Electrowinning Technology, involving all aspects of process chemistry, equipment and control, extends over a period of close to 30 years. The development in SX started with molybdenum and rhenium, continued with zinc, manganese, cobalt and nickel and is now focusing on copper. The OutoCompact VSF? SX concept, which has been recently introduced, is a honed version of earlier VSF? technology. The Outokumpu VSF? ("Vertical Smooth Flow") SX package includes the DOP ("Dispersion Overflow Pump") units, the Spirok Mixers, the OutoCompact Settlers including their DDG ("Dispersion Depletor Gate") fences and tank farm equipment such as the LOS ("Loaded Organic Scrubbing") tank as well as the CEP ("Copper Electrolyte Purifying") tank. Although the VSF? SX package can be implemented according to several optional lay-outs, the so-called Track version has lately been introduced to the advantage of new plants. The new OutoCompact SX technology decreases the footprint of future VSF? plants. The lay-out, including plant size flexibility, have further been improved by Outokumpu?s new OutoReverse settler technology. Two of several SX plants currently under construction rely on reverse settlers in order to maximize their performance. The Outokumpu EW technology includes process know-how as well as proprietary equipment. The copper EW package consists of permanent stainless steel cathodes based on wax-less technology and lead anodes utilising polymer concrete cells with the double contact bus bar system and ventilation hoods fitted for efficient mist control. The lifting of cell hoods, as well as cathode washing, is done by the cathode pulling crane. Proper electrolyte flows and matching current density further ensure high productivity of LME grade copper cathodes.

Jan 1, 2005

By Filipe Sathler

Mediante efeitos de sazonalidades do mercado Siderúrgico, períodos de crise, aliados às necessidades de reparos de equipamentos, os Altos Fornos são, eventualmente, submetidos ao desligamento. O procedimento específico mais utilizado é o Blowdown, com o abaixamento de carga até nível de ventaneiras, facilitando posterior limpeza e reparo. Para sucesso deste procedimento, é essencial um planejamento adequado das atividades. Informações técnicas e experiências operacionais permitiram o embasamento teórico e a execução do Blowdown do Alto Forno 03 da ArcelorMittal FCSA (Tubarão). Como preparação, foi efetuado o aumento do fluxo periférico (remoção de cascão) e o aumento da permeabilidade do Cadinho (maior circulação de líquidos, limpeza e drenagem). Realizou-se também a preparação de equipamentos específicos e controle dos parâmetros operacionais. O abaixamento de carga foi devidamente realizado conforme planejado, até o nível de ventaneiras e permitindo paredes internas livres de cascões.

Aug 16, 2017

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By D. C. Dahlin, W. K. O’Connor, G. E. Rush, C. A. Summers, S. J. Gerdemann

The Albany Research Center (ARC) conducted studies of mechanical activation by conventional and ultra-fine grinding techniques to enhance olivine reactivity in mineral carbonation reactions. Activated olivine is one of several solid feed materials used at ARC in reactions with carbon dioxide to form carbonate minerals. This paper compares grinding techniques via energy demand data and product characteristics, including particle size distributions, surface areas, full width at half maximum (FWHM) XRD analyses, and particle morphology by SEM analyses. Reactivity was gauged by percent conversion to carbonate in subsequent carbonation tests.

Jan 1, 2004

By Gang Chen

This paper explores the possibility of using short-term time-dependent plate loading tests to estimate the elastic and viscoelastic parameters of the weak floor strata typically associated with coal seams in Illinois. Plate loading tests with incremental loads, similar to incremental creep experiments, were conducted until the floor failure occurred. For each increment, the load was held constant for a period ranging from 1-4 hours until a constant deformation rate was achieved. The deformation-time data were analyzed for viscoelastic parameters of weak floor strata assuming its behavior to be adequately represented by the standard Burgers model. The analysis required development of mathematical equations for the time-dependent deformation of the standard Burgers material under a three- dimensional state of stress. Time-dependent pillar settlement data at one mine were also analyzed for elastic and viscoelastic parameters of the weak floor strata using the developed equations. These parameters were compared with similar parameters estimated from plate loading tests.

Jan 1, 1990

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By A. A. Cochran

The purpose of this Bureau of Mines research was to investigate the theoretical and practical aspects of using ionizing radiation to promote chemical reactions that are of interest to metallurgists, and to carry out a radiation study of a suitable reaction. The effect of 44,000 roentgens per hour of 120,000-volt X-rays on the chlorination of highly pure mixtures of rutile, carbon, and various catalysts at temperatures up to 540° C. is described. At these low temperatures, recoveries were very low; however, in the eight different systems studied, an increase in yield due to X-rays was statistically significant in two instances and was of borderline significance in a third instance. In the other five systems, the differences in yield were not significant. Impurities and added catalysts caused relatively large variations in the yield of TiC14 from the reaction. Although the catalysts employed were reported in the literature as positive catalysts for the reaction, most of them were negative catalysts for the highly pure system studied. With only one exception, each increase in the purity of the charge resulted in a decreased yield of TiCl4. The experimental results indicate that many substances catalyze the reaction studied and suggest that the differences in reactivity of the charge stocks may be due to their various contents of positive and negative catalysts.

Jan 1, 1962

By Martina Cadorin

Activated nanoporous biocarbon (aNBC) was prepared using E. grandis wood as a precursor material. Oxidated activated nanoporous biocarbon (ox-aNBC) sample was obtained from the aNBC by oxidation with nitric acid. The samples were tested as Pt nanoparticles catalysts support for ethanol oxidation reaction and as electrode materials for supercapacitors. The porous structure, chemical properties, and the structural and morphological characteristic of the materials were correlated with their electrochemical behaviour. Biocarbon materials showed similar high specific surface area. The oxidation treatment increases the content of the oxygenated and nitrogenated surface functional groups but without appreciably change in the nanostructure characteristic. The aNBC supported Pt nanocatalyst has better electrocatalytic performance for EOR. Oxygenated functional groups have a marked effect on the supercapacitors electrode behaviour, increasing the total electrical capacitance by pseudocapacitive contribution, but with a negative effect on the cell electrical resistance and cell response time.

Oct 30, 2017