Search Documents

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982

By Robert H. Ridgway

Chromite has been produced commercially for slightly more than a century. Developed, at one time, chiefly as a chemical pigment raw material, it has subsequently found extensive application in other chemical industries - as a refractory material for furnace linings and as the sole source of the metal chromium. For some years prior to 1914, its use as a refractory predominated; but post-war development in alloy steels, principally stainless steels, enhanced the metallurgical demand in the form of ferrochrome with a consequent increase in the demand for chromite. More recently direct reduction of chromite in alloy-steel manufacture has been applied to a limited extent. Alloy steels containing varying amounts of chromium, with or without other alloying elements, now find extensive use in a ride variety of ways - in structural material, machines, industrial equipment transportation by land, sea, and air, sanitary equipment, food preservation, and a multitude of other uses. In recent years chromium plating has had wide application and has become important. industrially, but the amount of raw material consumed

Jan 1, 1936

By C. F. Jackson

This paper describing the mining practices at a mine in the Southeast Missouri district is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The conditions, operating methods, and practice described in the following pages arc those obtaining at a property in the Southeastern Missouri lead belt, St. Francois County, Mo. This property is the eldest in the county and is a consolidation of a number of separate mines originally opened up as individual operations many years ago. Present-day operations have necessarily to be adapted to suit the older levels, stones, and pillars, and also the recovery of ore from worked over areas which was considered too low grade to mine in the earlier days constitutes a different problem than that of development and mining in virgin ground.

Jan 1, 1929

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By R. A. Vik

The influence of thermal treatments on the grindability of low-grade hematitic iron ores from Michigan and Minnesota was examined in bench-scale tests. Treatment factors were roasting temperature, roasting atmosphere, and ore cooling conditions. Bond ball mill grindability and work indices were used as response indicators in evaluating the condition of the ore. Of the three treatment factors evaluated, roasting atmosphere, which brought about the con version of iron oxides to magnetite, had the most significant effect; roasting temperature had the next most important effect; and cooling condition had the least effect. Optimum grindability was obtained with reduced-quenched products of both ores at 650° C, near the alpha-beta phase transformation of quartz.

Jan 1, 1971

By Paul Russell, M. M. Kimberley, Erick F. Welland, Louis Cope, C. C. Mosher, William M. Shepard, William C. Larson, Graham Closs

Exploration activities in 1980 felt the effects of unstable economic conditions and oscillating metal prices. In the cyclical, boom-or-bust precious metals and uranium markets, precious metals activity flourished and uranium was definitely in a slump. By November last year, the price for vellowcake was down nearly $20 from two years earlier. Many mining and milling operations closed, particularly in Wyoming, New Mexico, and Colorado. Decreasing emphasis on nuclear power continued to impact the market, as did the Three Mile Island accident of 1979. Earlier forecasts estimated that 10 to 12 reactors would be ordered per year by US utilities throughout the 1980s, but current forecasts suggest that it may be 1983 or 1984, or even later, before any new US plants are ordered, according to Thomas A. Boyden, vice president of Nuclear Exchange Corp. "Without those new plants, the consumption loss to industry is 4 to 5 million pounds (1.8-2.3 kt) of uranium per year. The cumulative loss to the industry is currently estimated at 25 to 30 million pounds (11.3-13.6 kt)," Boyden said in a May 1980 presenta¬tion. Despite the plunging market, there were a few notable uranium explora¬tion programs: •Exxon expanded uranium exploration in New Mexico, where the company reportedly took preliminary steps toward acquiring mineral rights to a 22-km2 prospect, 19 km south of Santa Fe. • Mountain States Resources began the second phase of an exploratory drilling program on its Sinbad/ Solo prospect in Utah. • Also in Utah, Cotter Corp. drilled its first exploratory hole in the Dirty Devil River district. Exploration for precious metals in 1980, however, appeared to tend toward the opposite extreme. High prices sparked near feverish searches in Alaska, California, Colorado, and Nevada. Numerous mines abandoned years ago were revived with some signs of success. Significant gold finds were reported in California and Nevada: • Homestake Mining Co. announced a gold discovery in California estimated to contain over 5 Mt with an average grade of about 5.8 g/t. Because the deposit consists of finely disseminated particles not visible to the eye, many speculate that prospectors bypassed the area during the 1849 California gold rush. • Newmont Mining Corp. discovered two gold ore bodies-Maggie Creek and Gold Quarry. Maggie Creek reportedly contains an estimated 13.7 t of gold in 4.3 Mt of ore, and Gold Quarry contains about 31.1 t of gold in 9 Mt of low grade ore and 2.3 Mt of higher grade ore. Highlights of this year's exploration review include articles on the modest growth recorded in geophysical activity, technical developments in exploration geochemistry, the variety of new instruments being tested or made available for exploration, and a state-by-state exploration review for the year.

Jan 5, 1981

Uranium mining remains controversial in many parts of the world, especially in a post-Fukushima context, and often in areas with significant uranium resources. Although nuclear proponents point to the relatively low carbon intensity of nuclear power compared to fossil fuels, opponents argue that this will be eroded in the future as ore grades decline and energy and greenhouse gas emissions (GGEs) intensity increases as a result. Invariably both sides fail to make use of the increasingly available data reported by existing uranium mines through sustainability reporting ? allowing a comprehensive assessment of recent trends in the energy and GGEs intensity of uranium production, as well as combining this with reported mineral resources to allow more comprehensive modelling of future energy and GGEs intensity. In this study, detailed data is reported for numerous uranium mines around the world, including production, energy and GGEs intensity and reported mineral resources. An important aspect included ? arguably unique and never before published ? is the relationship between ore grade and recovery, which is crucial in future projections of uranium mining. Overall, the paper shows the importance of continuing to improve reporting by the uranium sector as well as the ability to analyse key trends and future projections in energy and GGEs intensity of uranium production.

Aug 1, 2013

By R. H. Estrada-Ruiz

This work analyses a new approach to estimates bubble size distribution of froth surfaces using artificial neural networks (ANN).Also, the robustness of ANN to interpret images with illumination perturbations, produced by light problems or dirt attached to the window of the video camera is evaluated. The experimental work was carried out in a laboratory flotation column, instrumented with an image acquisition system. The images were processed making use of a perceptron model with a hidden layer, sigmoidal transfer function and unitary bias, and the ANN trained with a back propagation algorithm. The results of validation show that ANN are reliable for learning and producing generalized predictions of the froth mean bubble diameter and bubble size distribution, when the model is trained using a database that contains information on the illumination intensity. Keywords: image analysis, neural networks, bubble diameter, bubble size distribution.

Jan 1, 2009

By T. Bertke

This document assesses the environmental aspects of a preliminary design for processing kaolin clay as the domestic resource for recovery of alumina by a hydrochloric acid leach-HCl gas induced crystallization process. The report covers waste sources, control measures, and potential environmental and health effects applicable to the process technology.

Jan 1, 1980

The Determination of Sound Exposures (DOSES) software was developed by the National Institute for Occupational Safety and Health (NIOSH) specifically for use by mine management and safety personnel. DOSES simplifies the record-keeping and analysis associated with time-motion studies and worker noise exposures, making it easier to identify and solve noise problems. The software relies on a time-motion study that profiles the worker?s daily activities. At the same time, noise measurements are collected with a dosimeter or sound level meter (SLM). Observations about the worker?s location and tasks or other activities are recorded along with times and durations so they can later be matched up with the noise data. After the completion of a time-motion study of the worker?s daily tasks and locations (possible noise sources), which measures the worker?s noise exposures during the recorded events, the information is entered into DOSES. The program then displays information about the worker?s accumulated noise dose over time.

Jan 1, 2009

By Syd S. Peng

Mountaintop removal (MTR) mining started in West Virginia nearly 30 years ago. This surface mining method can extract multiple coal seams as thin as a few inches in whole and minimum rock dilution in very steep mountainous terrain. MTR is highly efficient, even if coal seams are in close proximity and small in a real extent. Consequently, MTR has been widely used in the Central Appalachian coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impact on the surrounding area. During the past two years, however, the debate over MTR mining has grown quickly and has become very intense. This article describes chronologically issues raised by various parties, legal actions, impacts on mining permit applications and research projects developed to address the issues.

Jan 1, 2000

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By F. G. Miller, H. C. Miller

Petroleum technologists and progressive operators constantly are striving to increase the percentage of oil that may to recovered from reservoir rocks through wells. The exhaustive studies that have been made of the function of natural as in the production of oil, for example, have aided operators greatly in increasing the quantity of oil recovered from reservoirs. Natural gas dissolved in and otherwise associated under pressure with oil in reservoir rocks, however, is not the only source of energy available for moving oil through sands to wells. In becoming "reservoir—energy conscious" engineers have learned that in many petroleum reservoirs the edgewater flanking the oil accumulation constitutes a potential source of energy capable, through proper control, of increasing oil—recovery efficiencies materially. No longer is the encroachment of water into the oil— and gas—filled tart of the reservoir considered as an evil to be combatted by devious methods but rather a natural consequence, incident to the withdrawal of nil and as from the wells, that may be used advantageously in lengthening the flowing life of wells and increasing the economic recovery of oil and gas.

Mar 1, 1938

By G. W. Grove

The wearing of self-contained oxygen breathing apparatus, although relatively safe if proper precautions are taken, is dangerous if defective apparatus -is worn, if men with inadequate training, experience, and physical requirements are used, or if improper procedure is followed. This is proved by the fact that at least 26 men are known to have lost their lives while wearing-oxygen breathing apparatus since its introduction in this country about 35 years ago. Self-contained oxygen breathing apparatus, commonly called "mine rescue apparatus" and sometimes improperly referred to as "oxygen helmets," is the only equipment that can be used for respiratory protection against poisonous mine gases, regardless of concentration or against an atmosphere containing little or no oxygen.3/ Apparatus of this type was introduced in this country in 1907, and since that time it has been widely used in conducting rescue and recovery work after mine fires and explosions and in some other work. All oxygen breathing apparatus used in this country before 1918 was imported from Europe, and although this equipment provided safer, more rapid means of conducting recovery work after mine disasters, there were many mechanical deficiencies in the apparatus which resulted in the death of some of the wearers. This led to the research and experimental work by the Bureau of Mines that resulted in the development and manufacture of more reliable and efficient types of apparatus in this country.

Jan 1, 1944

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

By Felix duBreuil

The present sampling procedure for evaluating the rock dusting conditions in a coal mine is time consuming. This study considers means by which this procedure could be simplified. Surveys were conducted in six coal mines in Pennsylvania to determine the in¬combustible content of the deposited dust. Some 2,000 samples were analyzed and statistically evaluated. It is suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error.

Jan 1, 1972

A mobile vacuum sweeper to remove loose coal and coal dust from underground coal mine workings was designed, built, tested, and evaluated. The design was based on an extensive test program. Pick up and conveying rates vs. air volumes, velocities, and nozzle shapes were determined for coal rubble in a laboratory pneumatic handling system. A gas/solids separation system was developed and tested in the laboratory capable of separating the solids loading from the vacuum system air stream to the very high degree required to preclude degradation of the ambient (mine) air. Two designs were made, one for belt conveyor and one for general district cleanup. The belt cleanup machine was chosen for test and demonstrated in an underground coal mine performing cleanup work in belt haulageways and on ribs.

Jan 1, 1975

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006