Search Documents

By S. E. Phillipson

During the course of evaluations by the Mine Safety and Health Administration’s Roof Control Division, the controls on ground instability were investigated at surface and underground limestone mines throughout the eastern and southern United States. Structural geologic features, including joints and faults, were identified by basic geologic mapping as primary controls on highwall and back instability in surface and underground limestone mines. By comparing the spatial orientation of discontinuities and internal angle of friction with the orientation of highwalls on a stereonet, the potential for sliding, toppling, and raveling failures was evaluated in a semi-quantitative fashion. Structural geologic mapping identified faults and joints, which dismembered the back and were associated with ground instability, in underground mines. This paper documents the importance of recognizing structural geologic controls on ground stability in limestone mines, advocates basic geologic mapping as a critical component of ground control programs at surface and underground limestone mines, and provides examples of simple stability evaluations using the stereonet method.

Jan 1, 2006

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By W. W. Adams

The United States Bureau of Mines, in cooperation with the National Send and Gravel Association conducted a safety contest in 1929 Among producers of sand and gravel. Only 26 plants were enrolled, as the contest was late getting under way. It is hoped that a ranch larger number of plants will be represented in the safety competition of 1930. Two trophies, both of which were provided by Rock Products magazine, were awarded at the end of the contest; one trophy was given for the best safety record among plants working 100,000 or mare man-hours during the year and the other for the beat record among plants working less than 100,000 man-hours. The trophies were presented to representatives of the winning, companies on January 29, 1930, at the annual convention of the National Sand and Gravel Association at Memphis, Tenn.

Jan 1, 1930

By Paul Richardson

This paper will review several projects completed during the period from 1976 through 1984 which have been carried out utilizing big hole drilling concepts. The projects discussed will be from various industries to demonstrate the extent that big hole drilling methods are being used along with the current state of development. There will be a discussion of projects planned for the future where big hole drilling methods are the only technology being considered. Also included in the discussions will be an overview of the most recently completed heavy oil recovery project. During the next decade, big hole drilling methods will be used more and more in all industries where underground access is required. The safety, speed and economics associated with shaft sinking using drilling methods are becoming more and more recognized and the technology is rapidly becoming an accepted shaft sinking method.

Jan 1, 1985

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By J. M. Goris

"Researchers at the U.S. Bureau of Mines are conducting research on cable-type ground supports to assess their material and support properties and to provide design criteria for implementing cable supports as a workable roof control system under various underground mining conditions. Much of this work involves laboratory assessment of the material and support properties of cable supports using both conventional and birdcage steel cables. Included in this assessment are single and double cables, effects of changes in embedment length on support strengths, water-cement ratios, use of breather tubes, and pumpability and water-bleeding properties of grouts.IntroductionSince cable supports were introduced in the early 1970s, considerable research has been conducted in laboratories and at mine sites to understand their behaviour. The U.S. Bureau of Mines began a laboratory evaluation project in 1985 at the Spokane Research Center (SRC) to study the behaviour of cables supports under uniaxial loads so that the effects of various cable support components, such as grout and breather tubes, could be identified. Other objectives were to compare the behaviour of various types of cables and grouts and to collect meaningful data for numerical analyses. Pull tests were conducted to determine how cables supports reacted under uniaxial loads and how they failed when ultimate loads were exceeded. Such data are essential for the development of numerical models for analyzing rock mass behaviour when the rock is supported with cables.Test ProgramBecause each cable support can be composed of either single or double cables as well as a breather tube, pull tests were designed to include a variety of samples containing these components. A series of samples containing a single conventional cable, a neat cement grout having a water-cement ratio of 0.45, and no chemical additives was selected as a standard (Table I). Then one component in the system, such as the presence of a breather tube, was changed, and results of tests compared to results obtained for the standard samples to determine what influence that component might have on the behaviour of the support system. If significant changes in test data occurred, they could be attributed to that one component. To control the quality of the samples, the physical condition of the cables and tubes were monitored closely, and compressive and tensile strengths as well as flow properties were determined for the grout used in each test series."

Jan 1, 1991

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By Jorge Madias

A Aceros Arequipa é a maior siderúrgica do Peru. A empresa opera uma planta em Pisco, com uma aciaria para 850.000 t anuais de aço líquido, e uma capacidade de laminação de 1.250.000 t anuais de produtos longos. Um projeto de integração vertical incluindo coqueria non-recovery, sinterização e alto-forno foi considerado. Como parte do projeto, um forno piloto de coqueificação foi instalado, com o intuito de testar carvões próprios e importados e obter a máxima participação de carvão local nas misturas. Foram testados sez carvões peruanos e antracito. Os carvões importados escolhidos foram três da Colômbia e quatro dos Estados Unidos. Levando em conta as baixas propriedades dos carvões próprios, foi introduzida a estampagem da carga. A máxima participação dos carvões locais, mantendo a qualidade requerida, foi obtida com 80% de carvão peruano, e 20% de um carvão columbiano. Pode-se usar até 10% de antracito, junto a 60% de carvão peruano e 30% de carvão colombiano.

Oct 30, 2017

By R. Blickensderfer

The sparking and gas-igniting tendency of steels and alloys were evaluated my measuring the radiance of spark showers produced by grinding a sample on an abrasive wheel in air, the time required for a spark shower generated on an abrasive wheel to produce an ignition in an explosive gas mixture, and the energy and speed required for impacts between various materials to ignite an explosive gas mixture. Mixtures of air-methane were found quite resistant to ignition by showers of sparks. A mixture of air-9.S pct hydrogen was used to increase the sensitivity of the tests and to thereby extend the range of materials that could be evaluated. The results of the spark-shower tests indicate that carbon steels and the alloy steels found in coal-cutter tools are among the most sparking and most incendive of any materials tested. Stainless steels, nickel alloys, and tungsten carbide are among the least sparking and least incendive. The brightness of the spark showers depended upon the degree of oxidation of the abraded particles. Impact tests against hard rocks such as solid quartz and sandstone, showed that high-carbon steel was more inc endive in the hydrogen mixture than were the softer steels or the alloy steels found in coal cutters. Ignitions were found much less likely to occur at speeds somewhat lower than the speeds currently in use in continuous mining machines.

Jan 1, 1972

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By G. R. Moulder

A device was developed that measures dynamic stress (ultrasonic energy) transfer through installed rock bolts, a measure that is directly proportional to the degree of grout bonding of the bolt to the mine roof structure and thus the ability of the bolt to bear static stress. The rock bolt bond tester (RBBT) is a hand-held portable device that shows three ranges of bolt bond condition; i.e., one-third (Bad bond), two-thirds (marginal), or fully bonded. These are shown respectively by a red, yellow, or green light that displays for 4 s. RBBT performance was verified with 2 1/2-to 8-ft bolts installed in various types 0f mine roof structures (sands tone, shale, and boney coal-mud), and 15 now being tested by the Bureau of Mines in mines across the United States. The unit is about the size of a five-battery flashlight and contains the transducer electronics, and battery pack. The RBBT is designed for extreme ease of operation, requiring only manual contact with the bolt and signal read-out. The batteries are rechargeable and the package is designed for durability in a mine environment.

Jan 1, 1983

By G. St. J. Perrott, G. W. Jones

"In the course of its investigations pertaining to the promotion of safety the Bureau of Mines is actively engaged in investigating all promising materials that may be of value in rendering methane or other combustible gases, vapors, or solids less inflammable.Added substances are of value if such additions narrow the limits of inflammability, raise the ignition temperature, lower the speed of propagation of flame, or reduce the maximum pressure developed. Of major importance is the effect of added materials on the limits of inflammability, because methane is the chief combustible s liberated in mines, considerable work has been done with extinguishing agents on methane flames. For obvious reasons, a substance to be of value for the extinction flames should be a gas, or a liquid having a sufficient vapor pressure to give concentrations of the vapor in sufficient amounts to extinguish the flames or markedly narrow the limits of inflammability. The substance should be nontoxic, cheap, and noncorrosive and must be incombustible. Solids, such as rock dust, are undesirable and of little value for combustible gases because they soon settle out of the atmosphere, and their flame- extinguishing value is thereby lost. There are at present only a few gases and vapors-for example, nitrogen, carbon dioxide, and carbon tetrachloride-which meet these requirements.The extinction of methane flames by nitrogen, carbon dioxide, and argon has been reported by Coward and Hartwell 4; the extinction by water vapor by Coward and Gleadell 5, and the extinction by helium and carbon tetrachloride by Coward and Jones 6."

Oct 1, 1930

By A. Ouellette, E. Nilsson

"Preventative maintenance is a burden for equipment users but a demand from the machine suppliers to ensure performance. Machine availability depends on preventative maintenance being followed.Mining equipment is becoming more and more sophisticated and productive, yet less and less time is available for preventative maintenance. Manufacturers invest in reducing costs, simplifying operating requirements, and lowering maintenance requirements, but it is the users who must invest more heavily in the advanced maintenance systems to keep the units operating.IntroductionPreventative maintenance has been, and still is a key factor in avoiding disturbances in production due to equipment downtime. Manufacturers ask for it in extensive maintenance schedules, check lists, programs, etc. often with a ""threat"" that, if not performed, the machine guarantee will not be valid. Modern mining and construction machinery has become sophisticated, like all other machinery, with elaborate hydraulic, electric and electronic systems and computerized controllers. Maintenance organizations within the mining industry have grown to heavy cost centres just to keep up the availability of the equipment.It is difficult for machine manufacturers to have maintenance programs that suit every user. International suppliers have to deal with different cultures, education levels, environments, organizations, etc. Maintenance programs recommended by manufacturers often do not meet some user's needs while they are ""overkilling"" to others. Preventative maintenance schemes recommendations of what to do, in what frequency, etc.) usually fit mechanical components in the equipment, e.g. wear measurements, crack indications, lubrication, oil changes, etc. But how does one perform preventative maintenance on huge hydraulic systems, electrical and electronic systems and computers? Failures in these systems usually occur without any warning and are more or less impossible to predict. Another difficulty in creating effective preventative maintenance programs for these kinds of systems is the relatively low volume of mining and construction equipment that is produced per year. For example, although Atlas Copco is one of the largest manufacturers in the world of underground blast hole drilling machines, the company still does not produce more than a few hundred drilling jumbos per year. These are made in more than 10 different models, with different systems and components, and very often are custom adapted to the end user's requirements."

Jan 1, 1992

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1982 (October 1, 1980 -September 30, 1981) under its Minerals Health and Safety Technology program. Contingencies may require that a significant port ion of the program be deferred into fiscal year 1983. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau's overall goal of providing the systems technology required to create a healthier and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1981