Search Documents

By John R. Bartels

This report discusses an improved method for rerailing underground railcars devised in a joint effort by the Bureau of Mines and Hoesch MFD. This improved method utilizes a lightweight hydraulic ram with hand-pump activation to move a bridge-mounted roller carriage in conjunction with steel-reinforced air-lift bags. This method provides a lightweight portable system in which only two workers are required to perform the mine car rerailing operation. Because of the very narrow confines in underground mines, use of overhead cranes and other surface rail techniques is not possible. This new system is designed for very low profile work, and provides the necessary lifting force from light- weight compressed-air bottles.

Jan 1, 1985

By V. E. Edlund

As part of a research program for recovering alumina from domestic nonbauxitic resources, the Bureau of Mines investigated a lime-sinter, caustic leach technology for anorthosite. This report discusses the unit operations--feed preparation, sintering, and leaching. Acceptable pellets for the bench-scale sintering studies were prepared from mixtures of minus 200-mesh anorthosite and limestone using water alone as the pelletizing agent. Heating pellets at 1,270° to 1,360° C for periods of 0.5 to 2 hr, followed by a 15-min soaking period at 700° C and cooling to room temperature, produced a sinter that dusted to more than 90 pct minus 65 mesh. The weight ratio of limestone to anorthnsite was critical in producing sinter exhibiting good dusting and leaching characteristics. A ratio of 2.0 was optimum for the bulk samples of anorthosite and limestone used in this research. Leach solutions from lower ratio sinters were unstable; gelation became progressively more severe with higher ratio sinters. Leaching the dusted sinter with 10-pct Na2CO3 at 60° C extracted 85 to 90 pct of the alumina in a product solution containing about 50 g/l A1203. Leach residue in contact with pregnant solution tended to set up as a rigid gel as a result of cementation, comp action, and gelation. The presence of a calcium-sodium zeolite [(Cn,Na2)6?(Al2Si04)12?27-3OH20] in the ungelled residues seemed to be the main difference between gelled and ungelled residues.

Jan 1, 1982

By E. L. Garton

Michigan is becoming one of the important oil-producing States of the country. The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 19935.4/ The Bureau of Mines method of crude-oil analysis and classification-indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the t- me amount of kerosene and gas-oil combined, 7.2 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue or about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in 9 counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By D. D. Bush

Based on the results of this study, the underhand cut and fill stoping method, with mass destressing, is an effective method for controlling rock bursts and falls of ground for deep mining in the Coeur d'Alene Mining District. The procedure can be utilized to pull highly stressed pillars by converting from conventional overhand stoping methods or used as a primary recovery system. During the demonstration, only one minor rock burst occurred, with no injuries. The system facilitates accurate placement of vertical boreholes for effective mass destressing. Each mining cut is filled with cemented sandfill overlying a timbered mat that forms the back for the succeeding cut. For this demonstration, a cemented fill was mixed on the surface and piped to the stone. Costs for pillar recovery by this method are comparable and are considered cost effective over conventionally timbered overhand mining as a pillar recovery method.

Jan 1, 1982

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

By G. R. Smith

Critical and strategic metals are often present in small quantities in low-grade domestic ores. When these ores are leached, the resulting solution usually contains the metals in very dilute quantities. Selective electrowinning from dilute electrolytes was investigated by the Bureau of Mines. A metal deposit containing 84 pct nickel was electrowon from the leach solution of a complex domestic ore bulk flotation concentrate originally containing approximately 2 wt-pct nickel. Key to achieving accelerated deposition rates, in the case of dilute solutions, is the rapid movement of the electrolyte through the electrowinning cell. Pure, synthetic nickel electrolytes were used to establish deposition parameters, and to optimize electrolyte velocity or mass transfer rates. Hydrodynamic and electrodeposition parameters for both the synthetic and leach electrolytes are presented and the experimental research described. Selective electrowinning appears to offer a viable alternative to physical separation methods to obtain separate metal "concentrates" from low-grade ores.

Jan 1, 1983

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By D. Bogunovic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices, and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents a result of research work on development of an integrated data environment system for analysis and control of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where, and how much energy is being used. This developed system represents a framework for efficient management of energy consumption. Key words: surface mining, coal, energy consumption, Information System.

Jan 1, 2009

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability o mine safety management personnel to apply analytical techniques to Injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the application of the quantitative procedures to mine-specific accident/injury experience data is discussed in detail in the form of case studies. The accident data from three mines are analyzed, and recommendations for training are proposed for each of the mines on the basis of this analysis. The procedures to apply cost-benefit analyses are described along with the cost benefit ratios for the training program/policies for the mines.

Jan 1, 1993

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term 'mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937

By M. C. Ruiz, M. E. Godoy, J. B. Rivarola, M. W. Ojeda

The amount of Pd recovered from an exhausted olefin hydrogenation catalyst was found to depend on mixing technique, particle size, carbon percentage, chlorine flow, reaction time and temperature. Pd extraction was total when a sample in the 125-175 micrometre particle size range was chlorinated for 60 min at 723 K with 20 cm3 Cl2/min, for 60 min at 748 K with 30 cm3 Cl2/min and for 30 min at 773 K with 30 cm3 Cl2/min. No C addition was needed; the initial C content of the catalyst was sufficient for total recovery. Pd extraction was also affected by heat treatment in different atmospheres before chlorination. Treatment with O2, N2 and N2 with traces of O2 led to different degrees of oxidation of C and permitted the formation of oxidised Pd species. Thermal pretreatment in N2 with traces of O2 was most conducive to Pd extraction

Jun 21, 1905

By Ian Hooper, Alan Winter, Stefan Sadokierski, Craig Covil

The existing Tappan Zee Bridge was built in the late 1950s and has been working over its design traffic load for some time now. A new project, which is being jointly sponsored by the New York State Thruway Authority and Metro-North Rail Road, is looking at new alternatives to provide new road and rail crossings of the Hudson River. These include 2 to 5 mile and potentially longer tunnel crossing options that include hardrock TBM and EPBM opportunities. The paper describes the project needs and tunnel concept design work done on some of the alternatives. It also relates to the current EIS process for the project and talks about a possible double-stacked tunnel option. It also talks about the geology and environmental constraints relating to tunneling and provides and introduction to the tunnel ventilation work necessary for tunnel crossing of this magnitude. It does not report on the bridge engineering options being evaluated.

Jan 1, 2005

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915