Search Documents

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By G C. Bolton

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCl in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

A new method, localized uniform conditioning (LUC), was proposed in 2006 for modelling grades of small blocks of ore when data spacing is too broad for their accurate modelling by the linear regression based techniques, such as kriging (Abzalov, 2006). It represents a modified uniform conditioning (UC) technique that calculates the grade distribution functions for the large panels. LUC uses partitioning of the panels onto the small blocks and then ranks them in increasing order of grade. Based on the block ranks, a single grade value can be deduced for each block from the UC model of the gradetonnage relationships of the corresponding panel. After being first presented in 2006, the LUC method has been implemented in ISATIS© (commercial software) and became one of the common approaches for grade estimation when data spacing is broad in comparison with the estimated block size. Several years of study on the LUC method and its application to different geological environments, have allowed identification of the strengths and weaknesses of the method, which are as follows: ? The method produces accurate grade-tonnage functions, which are in a good accordance with a volume-variance relationship principles ? An initial ranking of the selective mining unit (SMU) blocks can be made by direct kriging from the sparse data grid. Therefore, the LUC method can be particularly useful at the early stages of exploration and mining project evaluations when sparsely distributed data is often the only available information ? Accuracy of the local estimation depends on the SMU ranking techniques. When ranking performed by direct kriging of the SMU blocks their spatial distribution is approximate. When the variogram of the studied variable is characterized by a large nugget effect, the block ranks produced by kriging can significantly differ from their ?true? distribution ? Block ranking can be improved using auxiliary data, either geophysical or geochemical. This allows use of the LUC method for integrating different data sets. In particular, LUC can be used for grade control in open pits by integrating resource definition data (e.g. drill-hole assays) and blast-hole assays. The latter are used for the block ranking.

Jan 1, 2014

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

By Ronald W. Schaefer

This report describes operations at the Rosiclare Fluorspar Works of the Aluminum Co. of America at Rosiclare, Hardin County, Ill. The works include the Fairview mine, the fluorspar mill, and related facilities. The publication covers exploration, development, mining and milling practices, mine-drainage problems, and other activities and is presented as part of the Bureau of Mines series of publications on mining and milling practices in various parts of the United States. The Rosiclare fluorspar area, for its size, has been the largest producer of high-grade fluorspar in the United States and probably in the world. The vein system in this area is over 5 miles long and 1/2 mile wide, and ore has been found as deep as 900 ft.

Jan 1, 1961

By Violeta Vigo, Raúl Arévalo

La Municipalidad Provincial de Cajamarca y la Empresa Prestadora de Servicios de Saneamiento de Cajamarca (Sedacaj) han generado una alianza público-privada con Minera Yanacocha para mejorar el abastecimiento de agua potable limpia y segura en una ciudad que carece del servicio de manera continua. Esta intervención consta de 11 proyectos orientados al desarrollo de capacidades, educación sanitaria y construcción de infraestructura moderna, con una inversión de US$ 13.4 millones a cargo de minera Yanacocha.

Sep 20, 2019

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

By William J. Karwoski

To improve rock-burst control in deep vein mining, a field demonstration has been carried out by the Bureau of Mines to test a new rock-burst control concept--rock preconditioning in advance of mining. The procedure is to fracture the major rock-burst-prone zone during the development of each level before production mining. This allows initial mining to begin in a preconditioned zone and later mining from the level below to end in a prefractured or preconditioned pillar zone that is relatively burst-free. This full-scale field demonstration was carried out On the 7700 level of the Hecla Mining Co.'s Star-Morning mine. An expected burst-prone zone along the main vein between 7 and 10 crosscuts, some 250 feet long by 40 feet above and below the level, was preconditioned by blasting a fanlike ring of drilled holes from each crosscut. The drill holes, up to 100 feet long and 4 inches in diameter, were loaded with high explosives and shot. About 4,550 feet of drilling and 9,000 pounds of explosives were involved in the effort. Comparison of preshot and postshot data from monitoring instrumentation indicated that the blasting did fracture the rock in the planned zone and did result in an immediate stress decrease and softening of rock. The field data compared favorably with predicted results from a finite-element computer model simulation of the destressing. Based on observations made during mining and on the data from the Hecla rock-burst monitoring system, there is no doubt that this preconditioning in advance of mining demonstration resulted in much-improved rock-burst control during first-floor mining. It was also concluded that preconditioning the vein was more effective than preconditioning the wall rock.

Jan 1, 1979

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

By Timo Kankaanpää

Keywords: Solvent extraction, dispersion, phase separation, CFD The liquid-liquid dispersion phases are separated by gravity in a solvent extraction settler. This separation step is made more effective by picket fences. The picket fence geometry and its physical placement have a significant effect on the separation process, because the purpose of a fence is to smoothen and control organic-aqueous dispersion flow in the first part of the settler and achieve a deep and dense dispersion layer in the front end of the settler resulting in a clean phase separation. In this study, physical phenomena in the solvent extraction process and phase separation in a solvent extraction settler with and without picket fences have been examined using a commercial CFX software package. It can be concluded that the used CFD-approach proved to be a complementary tool for optimizing and designing the solvent extraction settler.

Jan 1, 2005

By R. E. Gilchrist, R. F. Nielsen

When a gas is displaced by mother in a porous medium, and there is a relative immobile liquid present. there is a transition zone in which the gas composition varies from essentially that of the original gas to that of the injected gas. The change in extent of this zone with time may be governed by a mixing process in the direction of flow and by the rate of establishment of gas-liquid equilibrium, if the gases are appreciably soluble in the liquid. The relative importance of these two factors in deterri~ining the growth of the transition zone is discussed, with appropriate equations and experimental data. INTRODUCTION The various solution methods of oil recovery involve a transfer of the components of a mixture, whether within a single phase or between a liquid and gas. The similarity of a natural porous medium to systems used in separation and chromatographic processes makes it seem reasonable that certain concepts used by chemical engineers in "mass transfer" might be applicable to petroleum reservoirs. One approach, the HETP (height equivalent to a theoretical plate), involves a distance or length of time over which equilibrium might be con. sidered as established. Another approach involves direct use of a rate of mixing or rate of establishment of equilibrium. The latter approach has been preferred in relation to production problems. DISCUSSION AND PROCEDURE When a gas or liquid in a porous medium is displaced by one of different composition but miscible with it there will be set up a transition zone in which the composition varies from cssentially that of the original fluid to essentially that of the injected fluid. If the fluid being displaced is a gas, and there is a relatively immobile liquid present, the transition zone may be

By Wade A. Narin, James K. Mitchell

Hydroblasting is considered a distinct soil improvement technique from explosive compaction, though the blast designs for the two techniques are similar. Hydroblasting is a three step process developed for densifying unsaturated, collapsible soils, especially loess. The required steps are: prewetting the soil to an adequate saturation, placing and detonating the explosive charges, and consolidating the soil (squeezing the water out of the pore spaces between the soil particles under gravity) to a denser state.

Jan 1, 1995

By S J. Loach

Geological reconciliation is an indispensable part of BHP Billiton’s Western Australian Iron Ore (WAIO) operations. Since 2009 our reconciliations have been calculated in a single, centralised sequel-server database. This system draws data from across our operations and calculates a hierarchical sequence of reconciliation factors that span the company from the smallest grade control (GC) block to the whole of WAIO. It then presents the results using sophisticated graphical reporting tools.The initial motive for developing WAIO’s reconciliation system was to meet corporate compliance and public reporting requirements. The ability to validate our resource and reserve models by comparing their estimates of tonnes and grade with production figures remains the system’s principal function; however, as the system has matured, we have significantly developed its ability to support the improvement of various technical activities within the business. For example, the system can now calculate and report reconciliation factors for different resource classifications, short-term planning models and geometallurgical estimates.More recently, great emphasis has fallen on the system’s ability to detect and warn of possible geological issues that may pose a risk to either production schedules or product quality. We envisage a future where automated analysis of our large historical data set will enable high-risk conditions within future mine plans to be detected and highlighted.In all of these ways geological reconciliation plays an important role in contributing to this company’s financial and operational resilience.CITATION:Loach, S J, 2017. The development and future of BHP Billiton’s Western Australian iron ore geological reconciliation system, in Proceedings Iron Ore 2017, pp 415–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Pierre Filiatreault, Brian Straight, Stephanie Thibeault, Devin Castendyk, Londie Cameron

"Working on or near water at active, closed or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the U.S. Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at U.S. metal, non metal and coal mines (MSHA, 2000). Openpit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including: a) drowning, b) hypothermia, c) falls to the ground from the top of high walls, d) collapse of unstable access roads, e) rock falls and avalanches from pit walls, f) avalanchegenerated tsunamis traveling across the lake surface and g) rapid degassing events.Some pit lakes are simply not safely or easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on a regular basis is needed to monitor the evolution of water quality over time, verify the accuracy of numerical predictions and, ultimately, manage lake water chemistry and ecological risks. For pit lakes with surface water discharge, regular monitoring is used to appropriately design and adjust water treatment plants in order to produce acceptable site discharge water quality.As a product of these risks and the need for water samples, mining companies spend considerable expense on pit lake safety as part of monitoring programs. This includes training personnel for on water duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices and cold-water clothing called mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface and employing spotters who can directly communicate with emergency medical services to watch sampling activities because cell phones and radio signals can be blocked by pit walls. Some sites utilize redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires two boats on the water during pit lake sampling events, with a third boat on the shoreline, gassed and ready to go. In addition, water samplers are required to hold Marine Emergency Duties training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel in the event of an accident."

Jan 7, 2017

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Lewis Stansfield

A rotary displacement method was used to install permanent steel casings for bored piles through an asbestos tip. This method was chosen in preference to alternative driven systems because it was quieter and more versatile if obstructions were encountered. New equipment was designed and made specifically for the project, and stringent health and safety regulations had to be observed.

Jan 1, 2000