Search Documents

By C. J. Badenhorst

Oxides of sulphur are corrosive and are produced when sulphur-containing fuels are burned. Sulphur dioxide (SO2) is a colourless gas with a characteristic, irritating, pungent odour. Exposure routes to the human body are mainly through inhalation and skin and/or eye contact. Symptoms of exposure to SO2 may include irritation of the eyes, nose, and throat; rhinorrhea (discharge of thin nasal mucous); choking; cough; and reflex bronchoconstriction. To protect employees against the ill health effects of SO2 exposure, they are often required to make use of respiratory protection whenever entering areas were the SO2 levels exceed the statutory limits. The use of respiratory protective equipment should always be a last resort and should be considered only after other control measures have failed to reduce occupational exposure levels to below the occupational exposure limit or whilst other control measures are being investigated or implemented. Whenever the use of respiratory protection equipment is considered, it should always be used as part of a comprehensive respiratory protection plan. It is also extremely important that all potentially exposed persons are adequately and comprehensively informed and trained.

Jan 1, 2007

By I. R. Hanby

A simple solution to the problem of whether to round the calculated number of trucks up or down to the nearest whole number is to adopt as criterion the minimum cost per unit volume/mass moved, assuming all trucks in the fleet are of the same type. When the effects on journey time of varying haul-road slope are calculated for several rolling resistances, it is shown that the optimum angle of 7.5 degrees is moderately independent of both rolling resistance and height climbed; the lower the resistance, the lower the sensitivity to ramp angle, but if haul-road gradients do not exceed 1 in 10 (5.7 degrees) for safety reasons then travelling time will never be more than 7% greater than its theoretical minimum. Further calculations result in a graph of the maximum payload values to incur the minimum cost, for different values of total effective resistance

Jan 1, 1991

By K. W. John, L. Mueller

The rock mechanics approach to stability problems of steep rock slopes dealt with in this article has particular reference to the concept and methods of analysis developed by the Salzburg, Austria, school of rock mechanics. These theories are based on the principal postulate of the anistropy of the technological properties of in-situ rock masses. The present approach, which is more in line with geological engineering concepts, differs distinctively from the soil mechanics and engineering geological concepts commonly practiced in the United States. PRINCIPAL ENGINEERING APPROACH TO GEOTECHNICAL PROBLEMS AVAILABLE ENGINEERING CONCEPTS At the present time two different concepts are available for engineering analysis of underground structures and foundations in different earth material: soil mechanics and rock mechanics. Of these two branches, soil mechanics is, after 40 years of initially revolutionary and more recently evolutionary development, well established. Its principal concept of replacing in-situ soils or rock masses by perfectly homogeneous substitues has resulted in many practicable methods of analysis which, if applied with judgement, have resulted in successful applications throughout the world. Conversely, rock mechanics is still in the early stages of revolutionary development. Few, if any, standard concepts or methods of analysis have been established. Opinions vary widely. At present the professional background of an investigator very often determines the engineering concept to be applied to a particular problem, rather than its actual requirements if considered objectively. This paper stresses the rock mechanics or geological engineering point of view advocated by the Salzburg group. A review of the soil mechanics concepts is considered beyond the scope of this paper. THE "SALZBURG APPROACH" TO ROCK MECHANICS The rock mechanics concept as outlined here was initiated by Stini, based upon work by sander.1 Since

Jan 1, 1963

By E. A. Metz

Ergonomics is the art and science that tries to understand the complex interrelationships among employees, their work environment, equipment, work methods and job demands. Coal and metal/nonmetal miners are exposed to a higher number of ergonomic risk factors than in non-mining occupations. In addition, studies have shown that these miners experience more degenerative disc disease and osteoarthritis than comparable industrial populations. A general discussion of the risk factors that cause overexertion injuries and disorders will be presented. In addition, the basic principles of ergonomics will be discussed with specific cases to show how successful programs have been developed. A successful ergonomics program should simultaneously improve health and enhance productivity.

Jan 1, 2002

By Paul D. Klipfel

Introduction Mineral exploration interest, principally for gold, in the south-western Pacific has surged to new proportions. This is primarily due to the application of epithermal exploration concepts in the Australian-Oceana region. Other factors that have contributed to the high level of exploration interest include governmental policies supportive of mineral exploration, along with relative ease of tenure access and a relatively short bureaucratic process. This paper highlights exploration and development activities in the North Island of New Zealand, Fiji, Vanuatu, the Solomon Islands, and Papua New Guinea (Fig. 1). It provides a framework to understand the overall recent enthusiasm that has been brought to the south Pacific by explorationists. Through these recent developments, it is clear that the south Pacific region will become a significant gold producing area and thereby worthy of attention and study. Papua New Guinea alone is the free world's seventh largest producer (Table 1). And, with the addition of production from deposits presently being developed, this status is likely to be raised. History Gold was first noted on various Pacific islands in the late 1500s by Spanish explorers. They thought they had reached the legendary King Solomon mines. Since then, the history of prospecting in the southwest Pacific has coincided with the colonization of the region. Settlers in New Zealand extensively mined alluvial and lode gold deposits starting in the 1850s. The spread of European colonization to the more remote Pacific islands from 1880-1940 was accompanied by varying degrees of prospecting activity by planters, traders, and settlers. Some were successful, others may have been successful, but never returned due to hostile indigenous peoples or disease. In general, records of such prospecting activity are meager and exploration leads are, in some cases, gained through local village folk memory. Most early discoveries were alluvial finds. These led to placer operations, particularly in New Zealand, the Solomon Islands, and Papua New Guinea. Continued prospecting located lode deposits such as the Morobe Gold-field of Papua New Guinea, the Coromandel Peninsula of New Zealand, and the Emperor of Fiji. Some areas were prospected thoroughly. Yet others, such as Vanuatu, remained relatively unexplored until the present exploration surge began. During World War II, interest in minerals was diverted. It was renewed significantly until the middle 1960s and early 1970s when regional porphyry copper exploration was conducted.

Jan 10, 1987

By L. W. Burger

The need to establish and harmonise methodologies to quantify air emissions, atmospheric dispersion and the consequences of air pollutants (especially hexavalent chromium) from the ferrochrome industry became important aspects with the increasing demands for comprehensive impact assessments. The paper includes a synthesis of current knowledge on the following aspects: ? Locally and internationally accepted methodologies for the quantification of chromium emissions, including sampling methods and emission factors; ? A compilation of recognised and accepted air quality sampling and laboratory analysing techniques; and, ? Dispersion modelling and impact assessment tools. Depositing and removing materials from the chromium ore stockpile and wind erosion of exposed stockpiles result in mainly chromite emissions unlikely to contain significant amounts of hexavalent chromium. Pre-treatment processes such as drying, crushing and screening also produces chromium emissions, but mainly as trivalent chromium. The smelting of chromium is the major source of chromium emissions - open furnaces have the highest uncontrolled chromium emissions, followed by semi-closed and closed furnaces, respectively. Based on the current knowledge on emission rates, interim emission factors for particulate, total chromium and hexavalent chromium releases are provided. Ambient sampling and analytical methods to determine environmental exposure of the general public require that hexavalent chromium needs to be quantified in very low concentrations. Suggested sampling and analytical methods for both source characterisation and ambient monitoring are provided. The selection between dispersion models needs to be based on the size of the modelling domain and the complexity of the terrain. The discussion on dispersion models includes the US EPA?s Industrial Source Complex Model (Version 3), the AERMET/AERMOD suite of models and the CALMET/CALPUFF suite of models. Guidelines are also proposed for environmental exposure assessments including cancer and non-cancer health effects.

Jan 1, 2004

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

Waitemata Tectonic Event(25 Ma ago) created a subduction system from the northeast of Northland, causing: (1) the emplacement of the Northland Allochthon (24-23 Ma) which provided argillaceous limestone and serpentine to Northland, and minor copper to both there and East Cape (located off Northland then); and (2) Northland volcanism (from 22 Ma), which lacked economic mineralisation. The Kiwitahi Tectonic Event (1714 Ma) caused: (1) a realignment of volcanism - from coastal western Northland, to west of the Hauraki Plains (Kiwitahi); (2) a start to the migration southwards from Northland of (a) the Alpine Fault System towards Marlborough today, (b) subduction towards Cook Strait, and (c) volcanism towards Taranaki-to-Bay of Plenty (initially through Coromandel, Kiwitahi, and offshore west coast); and (3) a start to rhyolitic volcanism & associated hydrothermal activity. The latter caused epithermal mineralisation, providing in Coromandel the best known North Island metalliferous deposits. Andesitic volcanism has been active in both of these two contrasting, subequal belts since 22 Ma. Rhyolitic volcanism and hydrothermal activity was wholly restricted to the eastern Marshall Belt, with an abrupt limit to economic mineralisation at the Volcanic Divide (within Hauraki Plains) and a major change there to basaltic volcanism of the western Searle Belt. The Kaimai Tectonic Event (5-1.5 Ma) caused: (1) a temporary reversal in volcanic migration in the Searle Belt, and a duplication of rhyolitic & hydrothermal activity at Waihi (Marshall Belt); (2) the rotational rifting of both the Central Volcanic Region (by 30¦) and the Hauraki Rift (10¦), causing major curvature of the North Island and New Zealand, and the transfer of the offshore subduction system from Coromandel to East Coast; and (3) an effective end to Coromandel mineralisation. Post-Kaimai Volcanism (1.5-0 Ma) included: (1) andesitic volcanism in the Searle Belt, yielding the western coastal titanomagnetite deposits; and (2) andesitic, and rhyolitic & hydrothermal activity in the Marshall Belt - the latter providing geothermal energy, sulphur, and pumice/perlite deposits. Post-Subduction (Intraplate) Volcanism (10-0 Ma) developed in a steadily expanding northwest region of relative tectonic quiescence, as subduction and its volcanism migrated southwards. Intraplate volcanism was predominantly basaltic, providing excellent aggregate; but less common rhyolitic & hydrothermal activity provided geothermal potential and mercury at Ngawha and at Puhipuhi, and halloysitic clays of extreme brightness elsewhere in Northland. This volcanism has reached as far SE as Mayor Island, providing an early New Zealand mineral resource - obsidian.

Jan 1, 1997

By Thomas M. Barczak

The U.S. Bureau of Mines has been conducting research to optimize the design and utilization of mine roof support systems. An objective of these efforts is to evaluate the mechanical and structural responses of various mine roof support systems under simulated load conditions in the Bureau's mine roof simulator. Underground studies are also made to evaluate the in situ behavior of support structures. The purpose of this report is to document practical applications for longwall face and gate road supports that have resulted from these studies. This report is not intended to be an all-inclusive manual on every aspect of support utilization, but it does provide a comprehensive assessment of practical considerations relating to the mechanical and structural behavior of these support systems. Forty-six recommendations are made to provide assistance to mine operators in the testing, selection, and utilization of longwall face and gate road supports. Many of these recommendations offer innovative solutions to everyday problems faced by mining personnel in the control of ground in longwall mining.

Jan 1, 1989

By Evans E. C.

At first sight, the extinction of a mine fire by the action of some such gas as carbon dioxide would appear to be quite a simple and practicable operation. From a consideration of the theoretical aspects only of the question, it becomes evident that the matter is not so simple as it appears to be at first sight. The fire at the Senghenydd Colliery occurred as the result of the disastrous explosion of October 14th, 1913. This explosion was confined to the west side of the colliery; and as a result the timbers in the main intake on this side were set on fire; but these were soon buried beneath falls, and the tire continued under them. Attempts were made to extinguish it with water, with the aid of chemical extinguishers, and by digging it out; hut these had to he abandoned, and ultimately the fire-zone was sealed off by “ bashings” (stoppings). By December, progress in the decrease of combustion was so slow that it was decided to try the effect of inert gas. The installation, control and operation of the carbon dioxide plant and associated water-gauge are described in detail and conclusions drawn for the extinguishing of mine fires by CO2

Dec 1, 1916

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By Esher Hsu

Keywords: Recycling, Consumer Battery, Fee rates On November 11, 1999, all types of spent consumer batteries are proclaimed to be collected in Taiwan. Under current recycling system, all producers and importers of consumer batteries have to pay a collection/recycling fee to the Recycling Management Fund (RMF) of EPA based upon the rate approved by EPA. Collectors and recycling plants receive subsidies from RMF according to the collected and treated amounts audited by an independent auditing organization. Collected spent consumer batteries only reached 923 tons in 2002 equivalent to 10% of the total quantity sold at the same year. How to increase the collection efficiency of used batteries becomes an important issue for EPA in Taiwan. The objective of this study is to explore current recycling system of spent consumer battery in increasing collection efficiency. Results provide some suggestions to Taiwan EPA regarding recycling route, recycling system, recycling rates, and recycling subsidies.

Jan 1, 2005

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By W. J. Spat

Political risk is an integral part of the mining business in northern Andean countries. Peru, Ecuador, Colombia and Venezuela all have a higher than average political risk compared with other South American countries. Successful operations require good political-risk information, a thorough political-risk-management plan and a strategy to deal with political-risk perception on the part of the investing public. Colombia is perceived as about the riskiest place in the world to do business. A selection of recent headlines reads: “Colombia on the brink” (Economist, 1998), “Colombia’s ship of state is sinking” (Insight on the News, 1998), or simply “Bad news” (US Catholic, 1998). The World’s Most Dangerous Places rates Colombia as “currently the most dangerous place in the Western Hemisphere, and perhaps the world” (Aral and Pelton,1998). And many prospective investors and analysts say to Greystar Resources: “Yes, we love your results, but Colombia?”

Jan 1, 2000

By John R. Sturgul, Elizabeth Yost

The number of Native Americans presently working as mining engineers is extremely low-perhaps three in the entire US. At the New Mexico Institute of Mining and Technology, it was felt that introducing high ability students to mining engineering at the high school level would encourage more to consider mining engineering as a career. New Mexico Tech, in Socorro, NM, has initiated a continuing summer college program for Native American high school students. The program, which began in the summer of 1980, is designed to introduce participants to college life, enrich their high school curricula, and expose them to the problems and challenges of a career in mining and related engineering fields. Students From reservations throughout New Mexico with a demonstrated aptitude for science and mathematics were encouraged to apply for admission. Preference was given to high school sophomores and juniors since it is hoped that students will want to return for a second year before graduating from high school and beginning university studies. The program seeks to impress upon the students the need fir Native Americans in the fields of seience and mineral engineering.

Jan 7, 1981

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely: codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage like nuclear power generation where international cooperation is eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit their mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2003

By Fernando Generoso Neiva Ferreira

O aumento crescente dos requisitos de segurança a serem atingidos pela indústria automotiva vem cada vez mais exigindo a utilização de aços com maior conteúdo tecnológico, que é o caso do aço bifásico (“dual-phase”), que são caracterizados por uma microestrutura ferrítico-martensítica. Neste trabalho, estudaram-se, em escala laboratorial, os efeitos das temperaturas de encharque intercríticas (750, 800 e 850°C) e distintas taxas obtidas por dois diferentes meios de resfriamento (ar e ar forçado) na obtenção de microestrutura bifásica a partir de dois aços laminados a frio “full-hard” (produzidos industrialmente), com micro-adições de Nb e Mo e diferentes teores de C e Mn. Utilizando ensaios mecânicos de tração, microscopia óptica (MO) e eletrônica de varredura (MEV), observaram-se as influências da temperatura de encharque e da taxa de resfriamento sobre as microestruturas resultantes e as influências da presença de ferrita encruada, dos carbonetos não dissolvidos e da morfologia da segunda fase sobre as propriedades mecânicas das amostras estudadas.

Aug 16, 2017

By A. B. Hooker, L. C. IlsLey

"The last previous Bureau of Mines publication relative to details of permissible electric mine lamps is Bulletin 332, which describes 16 lamps approved prior to May 1930. Some of the lamps have become obsolete through the development of improved models which, with several new types, make it desirable to supplement the Bureau's published data relative to permissible electric mine lamps.In the following descriptions, lamps approved since May 1930 and prior to July 1, 1935, are placed in the three following groups: (1) Electric cap lamps, (2) electric hand lamps, and (3) lamps for miscellaneous applications,ELECTRIC CAP LAMPS APPROVED UNDER SCHEDULE 6B1. Edison model J lamp, approval no. 24. - The features that distinguish this lamp from earlier models of Edison electric cap lamps are:(a) The battery consists of two F-2 cells of square cross section and about 1-1/4 inches higher than M-14 cells in the model H lamp, making the battery narrower and higher than any of the earlier models of Edison cap lamps.(b) The cells are insulated from each other and the Monel-metal casing by enclosure in vulcanized-rubber baglike enclosures. Both cell terminals are insulated from the cell jar.(c) The battery is equipped with rubber-tube Bunsen-valve-type gas vents.(d) The battery casing is secured by a new-type magnetic lock.(e.) The battery and cover terminal clips have been redesigned to give a wiping contact."

Jun 1, 1936

By C. G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX/EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to copper concentrates and ores will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of chalcopyrite concentrate treatment with this unique industrially proven process will be delineated.

Jan 1, 2001