Search Documents

Detachment of Particles from Bubbles in a Stirred Cell

Sep 13, 2010

By Frank Rausche

Since the early 1980s, when the Road Construction Authority of Victoria authorized the dynamic proof testing of roughly 100 drilled shafts of 1.5 m diameter and typically 60 m length in Melbourne Australia, dynamic load testing has been applied worldwide for quality control of drilled shafts. Today, test capacities of 4000 tons or more are not unusual. On numerous occasions the authors have been involved in similar tests in the United States and test engineers from other countries have reported on experiences in many different countries. Without doubt, generating high test loads is most economically accomplished by dynamic load testing and this method is particularly well suited for testing piles founded in rock because of the rocks low energy dissipation. However, deep foundation professionals have on occasion expressed reservations about subjecting a drilled shaft to impact loadings fearing, for example, a degradation of the shaft ? rock interface properties or potential error sources due to uncertain concrete properties or shaft geometry. This paper will present numerous case studies, demonstrating the performance of rock socketed drilled shafts under dynamic loads. It will discuss the mechanics of the dynamic tests and the method of data interpretation, addressing the concerns stated above and investigating the limitations of the test method. The paper will formulate a set of recommendations for the design and execution of these tests.

Jan 1, 2006

By Paul S. Fisk, Arne Fareth, Julie Frietas, Francis Lo, Fidel L. Mallonga

INTRODUCTION This report describes the inspection of parts of the New Croton Aqueduct (NCA)undertaken for the New York City Department of Environmental Protection (NYCDEP)by Parsons Brinckerhoff Quade & Douglas, Inc., (PB) in association with Montgomery Watson Engineers of New York, P.C. (MWH). Support for the inspection was provided by AFC Enterprises, Inc., under Construction Contract CRO-333, “WM-11 New Croton Aqueduct Rehabilitation and Inspection Program.” The scope of the inspection work under CRO-333 included assessing the condition of the 10.3 km (6.4 mile) long, pressurized section of NCA and inspection of shafts, head houses and blow-off structures in both the pressurized and gravity sections. The CRO-333 inspection continued investigation work begun under ContractCRO-196, which ran from 1993 to 1997. The CRO-333 inspections were conducted from November 2004 to September 2005. Background The New Croton Aqueduct was put into service in 1891 to deliver water from the Croton River Watershed in Westchester County to consumers in New York City. Figure 1 shows the location plan of Croton Water Supply System. The design flow into Jerome Park Reservoir was 12.7 m3/s (290 mgd) and into the135th Street Gate House, further south, was 10.9 m3/s (250 mgd). The NCA has been operated as a gravity conduit from Croton Lake to Gate House No. 1, just north of Jerome Park Reservoir, since its original construction. The length from Gate House No. 1to 135th Street, which includes a major siphon under the Harlem River, has been operated under pressure. Croton Lake gate house, the north end of the alignment lies at Station 4+75; Shaft 33, the south end of the alignment lies at Station 1628+05. The diameter of the tunnel is 3.2 m (10.5 ft) in the siphon and 3.7 m (12.3 ft) in the Bronx and Manhattan sections. The pressurized sections, constructed in rock, consist of a brick lining surrounded by a mortared and grouted rubble backing. Figure 2depicts a typical tunnel cross section. The objective of the shaft and tunnel inspections was to locate and document defects, such as leaks, deterioration of lining material, cracks, spalls, delaminations,

Jan 1, 2007

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler's performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of -43 per cent (LHV basis). This operating unit has also proven the use of the world's first FW/BENSONTM vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 x 1000 MWe solid fuel power block.

Jan 1, 2012

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By H. P. Hermance

Preliminary examinations of the Parker and Webb deposits were made by E. E. Maillott, Bureau of Mines engineer in July 1942. The chemical and spectrographic analyses included in this report wore made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision successively of S. M. Shelton and of Paul M. Tyler, formerly regional engineer, Eastern Region. Beneficiation tests were conducted under the supervision of Frank D. Lamb. The mineral exploration was under the general supervision of J. D. Bardill, formerly district engineer. Acknowledgment is gratefully made to the St. Joseph Lead Co., in particular to John S. Brown and P. J. Mechin for their assistance. Special acknowledgment is made to the American Metal Co., Ltd., ,Ind to T. C. Moore for furnishing core-drill and assay data; to the Universal Exploration Co. and P. B. Jennings; and to the Northern New York Mining Corp. and C. H. Sprague for their permission to publish the core-drill dta. Excellent cooperation was given by Dr. W; M. Agar and C, L. Rogers of the Geological Survey.

Jan 1, 1949

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By R. L. Grayson

In 2010, MSHA began holding hearings on a new coal mine respirable dust rule, which proposes a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the ?hot spots? where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines? compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, seam height, and selected ?hot spot? counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications on the need for better dust control methods.

Jan 1, 2012

By P Hunger, H Günter, F Heinicke

High pressure grinding rolls (HPGR) have been used for more than 20 years to grind iron ore pellet feed. Besides coarse comminution (crushing), where HPGR are installed upstream of the ball mill, there are numerous flow sheets where HPGR are used after ball milling and dewatering for re- or finish grinding.There is a clear growing interest in grinding of pellet feed with HPGR during the last few years. In addition to their known advantages of low specific energy consumption, high availability, low steel consumption and improved pelletising processes the lower environmental load (reduced or no water consumption) became a strong driving factor for the application of HPGR in pellet feed grinding.This growing demand increases the interest in better understanding of the HPGR grinding process with fine iron ore concentrates. One of the most important process parameters is the moisture content of the feed material which influences the performance of the HPGR enormously. The HPGR can react to fluctuations of the fresh feed properties to a certain degree by adjusting grinding force and roller speed. Nevertheless, there are limitations by the physics of the compression process and the capability of water absorption by the concentrate. The capability varies for different concentrates and different specific surface areas. This fact has to be considered during engineering of the beneficiation plant.The paper focuses on the influence of feed moisture content on the HPGR performance in view of throughput, increase of Blaine number and process stability on the basis of numerous pilot plant tests, modelling results and industrial experiences.CITATION:Heinicke, F, Günter, H and Hunger, P, 2017. Influence of feed moisture on high pressure grinding roll pellet feed grinding, in Proceedings Iron Ore 2017, pp 187–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Safe underground mine backfilling with hydraulic fill requires efficient fill drainage and stable fill retaining walls or bulkheads. If any or both the above two requirements are not satisfied, such a backfilling operation creates unsafe conditions and may lead to backfill retaining wall failures. Mine backfill retaining wall failures are always associated with economic losses, fatalities and interruption to mine production. Mining industry wants to either reduce or eliminate these fill retaining wall failures. The fill retaining wall failures could be effectively avoided through the use of fibre reinforced shotcrete fill retaining walls and engineered drainage systems through the retaining walls. This paper presents the experience of the author in developing, implementing, and monitoring several hundred fibre reinforced shotcrete fill retaining walls at a mine in Australia with the highest safety standard. The details on the mine backfill drainage system and fibre reinforced shotcrete fill retaining wall designs are also presented.

May 1, 2007

By N E. Whitehead

An application to mine an ilmenite-rich sand deposit in Westland led to public concern about potential radioactive hazards should the ore be further processed to recover zircon or monazite. A review recommended that any material involved in the heavy mineral sand industry containing more than 0.05% thorium, uranium or their mixture should be considered a radioactive substance and, for mining purposes, a notifiable product. Safeguards for those occupationally exposed would operate via the Radiation Protection Regulations. The major safety requirement would be the minimisation of dust in certain operations.

Jan 1, 1993

By Richard A. Watson

A frequency-shift keying (FSK) modulator-demodulator (modem) network has been devised for the Bureau of Mines mine-monitoring systems. This network permits an unlimited number of remote stations to communicate with one central station over the same pair of wires. The network operates at a speed of 4,800 Bd at distances up to 5 miles. This report describes the development and operation of the modems. The theory of operation, schematic diagrams, and printed circuit board layouts are provided. Although the modems were built for a specific application, a more general use is discussed whereby the network would operate with a typical serial channel format.

Jan 1, 1985

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

I would like to thank The Australasian Institute of Mining and Metallurgy for inviting us to share with you some of our experiences in the handling, storage, and transportation of industrial minerals in North America. Cometals, Inc. is a wholly-owned subsidiary of Commercial Metals Company, headquartered in Dallas, a public corporation whose shares are traded on the New York Stock Exchange. Sales exceed one billion dollars. Cometals, Inc. is located in New York and specializes in marketing of chemicals as well as raw materials used in the manufacture of steel, refractories, abrasives, glass and ceramics. This makes us one of the larger regular shippers of industrial minerals. Many people are aware that industrial minerals need to be viewed and judged on the merits of their chemical and physical characteristics. In addition you are surely aware that close attention must be paid to the economics of these minerals to determine the appropriate value and competitiveness of the minerals or products delivered at the doorsteps of the consuming work. You may, however, not be aware that the handling and transportation of the mineral is of crucial importance, in fact, the transportation and handling costs of industrial minerals frequently are a major component of the value of the ores marketed and, therefore, it is only natural that close attention should be paid to them. Many of the industrial minerals require special handling to assure that the material reaches the consumer without being contaminated and without getting wet. I invite you to accompany me through the various steps involved in "delivering the goods" to the consumer.

Jan 1, 1989

By M. Grodner

Ground Penetrating Radar (GPR) is an electromagnetic geophysical reflection technique that maps reflections associated with a change in electric properties of the target medium. It can thus be used to map the geometry of geological features and fractures as these can have different electromagnetic properties to intact rock. GPR was used successfully to determine the position and nature of the fractures in the tunnel sidewall, in the area of the simulated rockburst experiment. By comparing the radar scans acquired before with those acquired after the blast, it was possible to determine which fractures were reactivated by the blast and where new fractures were developed. It was found that the mining-induced fractures that formed during the development of the tunnel were re-activated by the simulated rockburst, as indicated by their increased reflectance on the radar scans. In addition, several new tunnel sidewall parallel fractures developed in the area of the blastholes. GPR thus clearly shows how and where the fracture pattern changed as a result of the blast and contributed to the understanding of the mechanisms of damage associated with the blast, and perhaps rockbursts in general.

Jan 1, 2001

By Gordon M. Matheson

The factors which control chimney subsidence sinkhole development in weak rock were assessed by analyzing the characteristics of approximately 3000 chimney subsidence features along the Colorado Front Range. The area of study included features developed over abandoned mines in the Colorado Springs Coal Field, the Boulder Coal Field, and the Foothills District. The approximate locations of the areas studied are shown in Figure 1. Data were collected for sinkholes occurring over both room and pillar, and retreat mining areas in coal seams with a wide range of dips. The location, size, and approximate time of development of each sinkhole were documented. From these data, relationships were developed which describe the time rate of observable sinkhole development and the relative location of sinkhole development with respect to mined height, overburden thickness, and type of mining for relatively flat-lying coal seams. In addition, the observed locations of sinkhole development over steeply dipping coal seams were assessed for portions of the study area.

Jan 1, 1986

Apr. 9, AIME, Chicago Section, Chicago Bar Assn., 29 S. La Salle St., Chicago. Apr. 11-12, Geological Society of America, Cordilleran Section, annual meeting, University of Arizona, Tucson. Apr. 15, AIME, Morenci Subsection, Longfellow Inn, Morenci, Ariz. Apr. 15-17, AIME, South West district meeting, Jefferson Hotel, St. Louis, Mo. Apr. 17, AIME, Utah Section, New House Hotel; Salt Lake City. Apr. 21-22, American Zinc Institute, annual meeting, Hotel Statler, St. Louis. , Apr. 21-23, Chemical, Metallurgical, and Mining Society, and Diamond Drilling Research Laboratory, symposium on diamond drilling, Johannesburg, South Africa. Apr. 22, Assn. of Consulting Chemists & Chemical Engineers, Inc., general symposium, Hotel Belmont Plaza, New York. Apr. 25-26, AIME, New England Regional Conference, Kenmore Hotel, Boston. Apr. 26-May 11, Liege International Fair, Liege, Belgium. May 4-8, Electrochemical Society, Inc., Spring meeting, Benjamin Franklin Hotel, Philadelphia.

Jan 1, 1952

By Virginia E. Gleason

In this report, recommendations are made for programs to develop workable techniques to stop or prevent acid mine drainage formation in those underground coal mines where acid production could take place. These recommendations include development of mine closure technology, development of surface water infiltration control procedures, study of the effect of roof collapse on mine water characteristics, evaluation of the long-term effects of flooding underground mines above drainage, investigation of the effectiveness of section sealing in active mines, development of a simple model for predicting mine water quality and quantity, preparation of a manual on mine drainage abatement procedures, and development of a program to disseminate information on mine drainage abatement to the coal industry. These recommendations are based on an in-depth evaluation of information acquired over years of research on acid mine drainage formation, on numerous laboratory and field studies of methods of preventing or minimizing acid mine drainage formation, and on review of the geological, hydrological, and mineralogical factors involved. There are 772 references.

Jan 1, 1978

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996