Search Documents

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By A. B. Hooker, Ilsley. L. C.

"Several writers have called attention, in the technical press, to the possible failure of flame safety lamps in coal-dust laden atmospheres. Such writers question the safety or a flame lamp that has been proved only in atmospheres containing methane, believing that the resistance of the lamp to explosion would be lessened it coal dust constituted a part of the explosive mixture.If this be true, it follows that any series of tests devised to prove the safety of flame lamps for use in gaseous and dusty coal mines should not only embrace tests in mixtures containing various proportions of methane, but also in some of the tests the effect of adding coal dust to the explosive gaseous mixtures should be investigated.Some attention has been given this question by investigators, but the more common practice has been to make all tests in gas and air mixtures only, using methane when it was readily available. Apparently the English Accident Committee (1879-1886) who conducted tests upon 250 different lamps did not use coal dust in their tests. The first British requirements for the testing of safety lamps, issued as a result of the Coal Mine Act of 1911, made no mention of tests with coal duet.The Austrian Fire-damp Committee (1890) conducted a series of tests in which coal dust was used in some of the tests. In certain tests, the addition of coal dust apparently lowered the resistance of the lamp 1 meter per second. The Belgium investigators, Messrs. Watteyne and Stassart, conducted a series of tests in 1904 in which coal dust was used in a few tests without any marked difference in safety."

Dec 1, 1920

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

ON mineral lease 38 of the Sulphide Corporation Limited, Broken Hill, a shaft was sunk in the early days Ior prospecting purposes and at the present time it is accessible as far as the 1000-ft. level where a connexion exists with the main workings of the Corporation's Central Mine, mineral lease 9. About the year 1895· a crosscut was driven east from this shaft at the 1330-ft. level cutting the Central Ore-body in mineral lease 9 and the shaft is supposed to extend a further depth of 25 ft; but no records of any of this work are in existence, the whole of the evidence being based on hearsay and memory:Fig. 1 shows the position of the Extended shaft in relation to the main workings. The shaft filled with water to the 1000-ft. level where it overflowed through the crosscut to the main shaft and was pumped to the surface, but when the South drive on the 1300-ft. level was pushed to the southern boundary, it was deemed advisable for safety, to tap the water at this level and so relieve the...

Jan 1, 1919

By Philip Dubbeling

Conventional dynamic sheetpiling techniques are ill-suited to urban development because of the emission of excessive noise and ground vibrations. Drilled shafts and slurry walls alleviate some of these environmental concerns but add additional problems due to large bulky machines, reliance on dusty concrete plants and urban trucking grief. To solve these problems, pre-fabricated sheetpiles are hydraulically jacked-in by reaction principle using a compact and lightweight press-in machine, a so called the "Silent Piler". Through scientific analysis, definition and systemization of press-in machines and methods, new construction concepts such as the one-step approach, implant structures, functional design and life cycle design have been developed to comply with new basic construction principles.

Jan 1, 2006

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By A. U. Miller

Definite progress has been made in accident prevention in Illinois during the past few years; the State Department of Mines and Minerals is receiving excellent cooperation from coal companies and employees, the companies are making greater effort to maintain their mines in good condi- tion, and the employees are eliminating more unsafe practices. As a result, some coal companies have made commendable safety records that prove that coal can be mined with a comparatively low accident rate. However, there is need for further improvement, as the accident rate of the State as a whole is much higher than it should be. During the 55-year period 1882-1936, in- clusive, reports of the State Department of Mines and Minerals show a total of 7,005 (an average of 127.36 per year) men killed in and around the coal mines. Of this number, 6,425 (91.7 percent) were killed underground, 346 (4.9 percent) in the shaft, and 234 (3.3 percent) on the surface. Of the fatalities underground, 3,300 (51.3 percent) were killed by falls of roof, sides, or face coal, 1,167 (18.1 percent) by haulage, 639 (9.9 percent) by handling explosives, 579 (9 percent) by explosions, 151 (2.3 percent) by electricity, and 589 (9.1 percent) by other means. Of the fatalities in the shaft, 171 men (46.5 percent) were killed by falling down the shaft, 14 (41.6 percent) by the cage, and 31 (8.9 percent) otherwise. On the surface, 113 (48.2 percent) of the fatalities were due to railroad cars, 51 (21.7 percent) to machinery, and 70 (29.9 percent) to other causes. The fact that 7,005 lives (an average of 127.36 per year) were lost during 1882-1936 is sufficient evidence that in the past too little interest has been taken in safety by either the management or workers. A realization of this deplorable loss of life should act as an incentive to the industry to make greater effort to prevent accidents in the future. After an accident occurs, the facts pertaining to it become history, and anything that may be done afterward cannot change in any way the damage that has already been done, such as loss of life, personal injury, and destruction of property. The main benefit that can be derived from an acci- dent is that suitable procedure may be adopted and some lesson may be learned to aid in preventing a similar accident in the future. All accidents, par- ticularly serious ones, therefore should be investigated and an effort made

Apr 1, 1938

By Q Johnston

Since its inception in 1990, improved metallurgical processing technologies, coupled with mine planning enhancements and improved geological knowledge, have sequentially enabled better efficiencies and economies of scale at the Macraes Gold Project. Over a period of 11 years, processing enhancements have been achieved by: +        increasing mill throughput, from one million tonnes per year, to current throughput of 3.9 million tonnes per year; +        improving recovery rates, from 70 % to approx 84 %; and +        performance enhancement through innovation, eg the use of kerosene to combat ClL pregrobbing. Future processing improvements have been identified in optimising the ore feed and processing flowsheet. The introduction of the autoclave has transformed the process flow form a traditional 'mill headgrade and tonnes milled' operation, to a 'sulphur/gold ratio and sulphur tonnes oxidised' operation.

Jan 1, 2001

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By Ernest J. Conway

This report presents engineering drawings for six material handling devices for underground coal mines. The devices were designed under a U.S. Bureau of Mines program to reduce injuries from material handling during mine and equipment maintenance. The six devices are (1) scoop-mounted 1411: boom, (2) swing-arm boom, (3) heavy-component lift-transport, (4) mine mud cart, (5) container-workstation vehicle, and (6) timber car. Each device is described briefly, and recommendations are made concerning the design of new devices.

Jan 1, 1989

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

My selection of the Australian coal industry as the theme of this Presidential Address arose from the fact that it is one of our most important mineral industries. The industry is presently prospering.M.ore coal, mostly of better quality (except for certarn power-house types), is being produced more cheaply in terms of real money than at any time in the past, and exports overseas are currently at a highlevel.In. spite of this, concern has been expressed in certam quarters about the future of some phases of the industry; for example, there has been some public comment on the selling price of our coking coal to Japan, the possible over-export of our coking coals from New South Wales, the introduction of foreign capital to develop large-scale mining ventures in Queensland, and the proposed export of substantial quantities of coking coal from the same State.Furthermore, proposals for the introduction of atomic power plants into several States well endowed with reserves of coal have given rise to comment, and recently the Department of National Development(1968) warned that insufficient attention is being paid to "orderly development and careful husbanding of the nation's coal.To reach a balanced judgment on whether these views are well founded it is essential to make a broad survey of the present position of the coal industry in the Australian economy. I therefore propose to deal briefly with several aspects, and to comment, in particular, on the important subjects of exploration and research in progress at present on Australian coals.Detailed descriptions of the Australian coalfields are to be found in existing technical publications (e.g.. Andrew, 1965; McLeod, 1965) and the data on coal reserves have been progressively revised as more accurate information has become available. In New South Wales detailed knowledge of the coal reserVes is limited to under 20 per cent of the sur...

Jan 1, 1969

By M. D. Balen

The U. S. Bureau of Mines has undertaken the development of mineral industry cost escalation factors to enable the estimation of mineral development and extraction costs for mineralized sites in Alaska throught the use of the Bureau's Cost Estimating System v2.0 (CES 2.0). For the purposes of this document, all calculations are based on, and reflect the economic environment in Alaska in July 1992. The greater cost of mining in Alaska as compared to the contiguous-48 States can be estimated for Alaskan mining operations through (1 ) the analysis of capital and operating costs for analogous mine and mill plants in operation in the contiguous-48 States; (2) the hypothetical relocation of mine and mill plants from their actual location(s) to Alaska by making engineering modifications to the mine and mill plant design as required by the Alaskan site characteristics; (3) calculation of the cost of the required engineering modifications and; (4) the escalation of all costs to a level representative of the economic environment in Alaska at some specific point in time.

Jan 1, 2011

By Jason M. Ryan, T Michael LeBlanc, John H. Heiiig

Drill trajectory deviation is a recurring problem in the Mining Industry retreat stoping operations. As a result of this deviation, it is quite concevable that 60 kg (165 mm 0) and 103 kg (203 mm 0) explosive charges are detonated beyond the hanging wall contact. Consequently, there follows a reduction in hanging wall stability and an increase in ore dilution.

Jan 1, 1995

By J. C. Cawley, G. T. Homce, M. R. Yenchek, H. K. Sacks

As in many other industries, such as construction and agriculture, overhead electric power lines are a serious hazard at mining and mining-related operations. Even when excluding injuries that occur during electrical maintenance work, over one fourth of electrical fatalities in the mining industry are due to accidental overhead line contacts, and for each fatality nearly two serious non-fatal injuries occur due to such contacts. In incidents involving high-reaching mobile equipment, many of the victims touched the equipment after the fact, unaware that the machine frame had become energized by the line contact. MSHA data for accidents involving overhead power line contacts in the mining industry between 1980 and 1997 reveal that in 57% of the cases personnel were unaware of the accidental line contact until after one or more workers touched the equipment or a hoisted load and were injured. The situation is similar in the construction industry, where according to the National Institute for Occupational Safety and Health (NIOSH) data at least 20% of such victims are unaware of the line contact. This suggests that a device that alerts workers when a power line has been contacted could help prevent many of these injuries. Such a device would not prevent power line contacts, yet if widely employed could yield a significant reduction in the number of resulting injuries. Researchers at the NIOSH Pittsburgh Research Laboratory are attempting to develop such a device. The approach being investigated is based on measuring electric current flow to ground through a machine during a line contact. The specific technique being tested involves the diversion of some part of this current through a shunt cable mounted on board the machine, to provide a point at which to install a current sensor. Experiments thus far indicate that this approach is feasible. Ongoing research is better defining electric current flow through mobile equipment, refining techniques for measuring this current, and identifying factors that could limit the effectiveness of the proposed alarm.