Search Documents

By R. E. Wilmot

This paper is based on the experiences, over many years, on the part of numerous authors in the South African mining industry and that of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a practical example; ?case history? where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions to be encountered in a new mining operation (now 10 years on) and concludes with two follow up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2006

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By C. R. Edwards

"The Cigar Lake project will develop the world’s second largest high grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the high grade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2005.INTRODUCTIONThe Athabasca Basin in northern Saskatchewan hosts a number of large uranium mining and milling operations, including Cluff Lake, Key Lake, McArthur River, McClean Lake and Rabbit Lake. (Edwards 1988, Edwards 1992, Fielder 1998, Edwards and Oliver 2000, Edwards 2001) The latest project in the Athabasca Basin is the Cigar Lake project."

Jan 1, 2002

By John J. Henn

An economic evaluation was made of the Bureau of Mines incinerator residue separation process to update the one published in 1971 to a mid-1.974 cost basis. This evaluation includes a modification of the glass-recovery operation used In the original plant design as well as a unit to bale the ferrous scrap product before shipment. Products from the plant are ferrous metal, aluminum and copper-zinc scrap, and a mixed-color glass cullet. The estimated capital and operating costs for four plant sizes are as follows : [ ] The operating costs do not include credits for recovered metals and glass.

Jan 1, 1975

By Luis-Fernando Contreras, Juliano Maran, Richard LeSueur

A risk study was carried out at the Cerrejon coal mine in order to assess the impacts of pit slope failure in terms of safety of personnel and destruction of equipment with economic consequences. Results of the assessment enabled the definition of risk treatment requirements and the identification of key aspects to consider in a risk treatment plan. The approach included the following tasks: (1) Assessment of the total probability of failure (POF) representative of the stability conditions of typical footwall and highwall slopes. For this purpose, stability analyses were carried out to define the Design POF, which accounts for the variability of strength parameters and represents the normal conditions considered for slope design. Strength parameters for highwall slope analysis were derived from borehole data obtained with a geotechnical drilling campaign. The Total POF was estimated through the use of Source Response Diagrams (SRD) in order to incorporate other sources of uncertainty not accounted for, like changes in geometry, variability of rock conditions due to geological or operational factors, changes in groundwater conditions and occurrence of seismic events. (2) Assessment of the consequences of footwall and highwall slope failure on safety of personnel. The assessment was performed through the use of event tree analysis to establish the probability of fatality caused by slope failures, from the Total POF defined in the previous task. This analysis required the evaluation of personal exposure to slope failures. Also, the assessment included benchmarking of acceptability criteria in terms of probability of fatality and the evaluation of options of risk mitigation to comply with these criteria. (3) Assessment of the consequences of footwall and highwall slope failure in terms of economic losses associated with impact on equipment. The analysis included the evaluation of equipment exposure to slope failures, and it was performed through event tree analysis to establish the probability of an economic loss associated to total or partial lost of equipment, from the total POF value defined in the first task. The magnitude of the economic losses was estimated from the costs of damaged equipment, lost production and site restoration. Options of risk mitigation were also examined in terms of economic losses. The risk assessment process applied to the Cerrejón mine showed how the system can be applied to evaluate the consequences of failure in terms of personnel safety and economics and to identify the more adequate risk mitigation options. The system can be an extremely powerful tool in the mine design process and provides the opportunity to rationalize the geotechnical information requirements, once the risk criteria have been defined by management. The main purpose of this paper is to present the process; therefore, the emphasis has been put on the methodology followed rather than on the actual results obtained.

Jan 1, 2006

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By Roger L. King

Working in gassy ground conditions is an everyday occurrence for the U.S. coal mining industry. As tunneling operators begin to venture into projects that expose them to the additional hazard of potentially explosive atmospheres, lessons learned by the mining industry over years of experience should be transferred into this industry. This paper will present practices developed by the U.S. coal mining industry for dealing with the problem of excavating material in potentially explosive atmospheres. Procedures will be discussed that can be used to detect and quantify gas prior to mining that have application to the construction industry. Degasification or drainage practices, including predrainage from vertical and horizontal boreholes, will be discussed. Also, ventilation practices commonly used in the mining industry will be presented.

Jan 1, 1985

To date Iron Monarch is the most important Australian source of iron ore and since HH5 has produced about 84 million tons of direct shipping ore containing 62 per cent iron and 3 per cent manganese.Previous geological work, mainly by Rudd, Edwards and Miles is reviewed and the results of later exploration by quarrying and drilling are discussed and modified interpretations of both stratigraphy and structure are advanced. Renewed study of the mineralogy of the iron ores is advocated.The Iron Monarch orebody lies on the up-thrown side of a major transcurrent fault that truncates it on its northern boundary. The nearby Iron Knob orebody is believed to occupy a horizon that is some thousand feet stratigraphically above Iron Monarch.The origin of the ore cannot be explained by any simple theory; development probably took place over a long period of time from Lower Palaeozoic to Tertiary.INTRODUCTIONIron Monarch orebody has supplied the Australian iron and steel industry with the greater part of its ironstone requirements since the establishment of the Newcastle steelworks in 1915. Annual production of direct-shipping ore has exceeded three million tons but declined slightly after 1956 when Iron Prince was brought into production. Total production of ore from Iron Monarch to the end of 1962 is about 84,000,000 long tons containing some 55,000,000 tons of metal.The deposit (Lat. 32°44'30"S : Long. 137°08'30"E) is 34 miles north-west of Whyalla, on the western shore of Spencer Gulf. A 42 in. gauge railway connects Iron Monarch and its associated small town of Iron Knob with Whyalla (Fig. 1).For the purpose of this paper Iron Monarch includes Iron Knob and the intervening jaspilite hill known as Substation Ridge, and the description of the general geology necessarily 'Assistant Chief Geologist, The Broken Hill Proprietary Co. Ltd.This paper was presented at the Annual Conference of The Institute, 14-24th August 1968.

Jan 1, 1964

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016

By A. Livingston

This paper on mining practice at the Fresnillo silver mines is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Two classes of ore are produced at Fresnillo. A low-grade oxidized silver ore; end a complex-base sulphide are containing gold, silver, lead, zinc, and copper. This paper is confined to a discussion of operations relating to the production of oxidized silver ores. To date, more than 10 Million tons of this ore rave been mined. The present (June, 1931) daily production is 2,000 tons of ore, and approximately 600 men are employed in the mining operations.

Jan 1, 1932

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By Arthur A. F, MacKenzie I. H

Copper in zinc/lead sinter charged to the Imperial Smelting Furnace operated by Sulphide Corporation Pty Limited at Cockle Creek, New South Wales, concentrates in a complex lead dross which forms as the bullion is cooled to around 400°C. The 0.35 mm portion of this dross, containing approximatelY 67 per cent of the total copper, is treated via a hydrometallurgical route to produce 5000 tonne/yr of CuSO4 5H2O crystal.Around 3000 tonne/yr of copper-lead dross containing 49 per cent copper is leached at 55°C in continuous leach reactors with ammoniacal ammonium carbonate leach liquors to convert copper to soluble copper amine complexes. Leach ettlciencies of 80-85 per cent are obtained. Leach residues are repulped with ammoniacal liquid diluents from the plant and heated in a four stage steam distillation unit to reduce ammonia levels to between 0.5 and 1.0 g/Iitre. The resultant slurry is directed to an effluent treatment plant for final treatment, and separation and return of solids to the sinter plant.Copper is extracted from leach liquor by solvent extraction techniques based on the use of L1X 54 diluted 3:1 with Shellsol 2046 to give a nominal copper loading of 30 g/litre. The loaded organic is contacted with a sulfuric acid solution of pH 5 to remove the bulk of ammonia and zinc, then stripped at 55°C with a 60 g/Iitre H2SO4 95 g/Iitre copper solution to yield a 15 g/Iitre H2SO4 125 g/Iitre copper solution.This liquor is fed to an adiabatic vacuum crvstalliser operating at 35°C and 5 kPa vacuum where crystals of CuSO4 5H2O are formed. Crystals are separated from mother liquor and washed in a two stage pusher centrifuge, then dried in a hot air rotary drier. The crystal product obtained is of a high chemical purity and readily conforms to both Australian and overseas standards.

Jan 1, 1983

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy's law for fluid transport, can be written as:

Jan 1, 1967

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By M Begbie, R J. Norris, D J. MacKenzie

The Otago Schist is crossed by numerous deformation zones that formed in the latter stages of metamorphism and uplift of the metamorphic belt. These deformation zones are long (tens of km) linear features at the regional scale, and are generally narrow (km scale or less). Many of these structural zones separate schist domains with different rock types and structural/metamorphic histories. The Hyde-Macraes Shear Zone is one such deformation zone, and this zone hosts the active Macraes gold mine. The Rise & Shine Shear Zone, 80 km NW of Macraes, is also enriched in gold and has been mined historically. Mineralisation in both these shear zones occurred during the transition from ductile to brittle deformation as the schist belt was uplifted from greenschist facies metamorphic conditions. Recrystallisation of quartz and micas in the early stages was overprinted by cataclasis, with sulfide and gold precipitation throughout. Many of the other late metamorphic deformation zones formed under similar greenschist to sub-greenschist facies conditions, with similar overprinting of recrystallisation textures and folds by more brittle textures such as breccias. Under these conditions, originally regionally pervasive deformation at the highest metamorphic grades was evolving towards more focussed high strain zones at lower temperatures and pressures. Shear zones initially focussed fluid flow along microshears and mineral grain boundaries, resulting in 1 to 100 m scale alteration and replacement in the host schist, with only local development of quartz veins. Fluid flow was not controlled by open fractures, and the rate of fluid movement was probably slow and pervasive. After uplift into the brittle regime, the schist belt underwent tectonic extension. Extension was accompanied by development of swarms of steeply dipping veins, with localised mineralised normal faults. Hydrothermal fluid flow throughout this uplift history was a normal consequence of late stage devolatilisation of the metamorphic belt. Hence, all late metamorphic deformation zones should be considered prospective for gold accumulation.

Jan 1, 2005

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By Stephen C. Tadolini, Steve Bessinger, James Pile, Christopher Mark

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan’s geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro-active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

By Ralph M. Foecking

The disposal of the phosphate slimes produced by Florida beneficiation operations is perhaps the biggest single problem of the phosphate mining industry. This is an old problem which has not been solved and which is becoming increasingly severe. In a typical phosphate mining operation, the phosphate rock mined is initmately mixed with sand and clay, constituting what is known as matrix. During the beneficiation, the clay and other fine materials are separated usually at -150 mesh, and washed from the phosphate rock in a form of diluted slurry known as phosphate slimes. The quantity of slimes solids and their composition vary considerably with the location but usually represent from 25 to 35% of the ore mined. Because of the affinity that clays have for water, large volumes of water are required to separate the granular material in the matrix forming a dilute slime suspension (1.5 to 3% solids) of colloidal material, which settles very slowly, and thus requires immense impounding areas, which never becomes totally usable land. These ponds also contain about 25 to 35% of the total P205 values mined. The magnitude of the problem represented by the slimes can be appreciated better if we realize that there are around

Jan 1, 1971