Search Documents

By Alvin J. F

Tin in ores containing 0·025 to 1·5 per cent tin can be determined polarographically by the reduction of the chlorostannite ion at the dropping mercury electrode in 2M hydrochloric acid solution containing 15 per cent ammonium chloride. The tin is separated from interfering elements by distillation as the tetrabromide and collected from the distillate by co-precipitation with aluminium hydroxide. The method can detect 0·01 per cent tin in ore.INTRODUCTIONAn iodimetric method, suitable for routine analysis of titrating tin in concentrations down to 1 per cent, has been available for some years (Low, Weinig, and Schoder, 1939).As concentrations fall below 1 per cent tin, there is increasing difficulty in obtaining a distinct end point due to large amounts of iron and silica normally present after fusion of the ore. Since concentrations of tin down to 0·02 per cent are significant in ore dressing products it was necessary to examine methods to determine such low concentrations, and to adapt these to tin ores containing a wide variety of other minerals.EXPERIMENTALDigestion and separationCassiterite, the principal tin mineral, is refractory but readily attacked by a sodium peroxide flux to yield soluble sodium stannate. In a recognized procedure, a sample of ore is mixed with up to 15 g of sodium peroxide in an iron crucible and swirled over the full heat of a Meker burner for 7 min. The fusion is leached with water and acidified.This solution then contains tin, silica, and other soluble...

Jan 1, 1962

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

On-stream determination of xanthate concentrations can be made by photometric measurements at 313 nm.A simple double-beam instrument was developed for this purpose. A mercury lamp is used as the light source and a composite filter of UGll glass and chromate solution is used to isolate the required spectral region. The light beam is split into two components of approximately equal intensity. One component is passed through a reference cell containing water to a photo detector; the other component is passed through the xanthate solution to a second photo detector. The reference signal controls amplifier gain to eliminate effects of lamp intensity changes and the amplified sample signal can then be used to measure xanthate concentration.Plant trials showed that provided a clear solution free of air bubbles was obtained from an on-stream filter, the instrument indicated the xanthate concentration and operated satisfactorily for long periods.

Jan 1, 1973

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

The only economically significant deposit of dolomite in New Zealand is at Mount Burnett, in north-west Nelson. The dolomite, associated with marbles and schists, is complexly deformed, and is of Paleozoic age.A very large quantity is present, although the recoverable amount is to some extent limited by the difficult terrain.Physically the quality of the dolomite is excellent. It is a tough, durable, fine grained rock. Chemically it is a little more variable. The range and frequency o~ the more important impurities are illustrated by hlstograms, as is the "dolomite factor"-a measure of the amount of the mineral dolomite in the rock. lbe dolomite factor averages 84 per cent, the remainder of the rock consisting largely of calcite. Quarrying, milling, production, and uses are described. In 1966 production reached 13,250 tons.

Jan 1, 1969

By John J. Sammarco

Mining has one of the highest annual average fatality rates among major US industries. Health and safety dangers have been inherent to mining since the early days of picks and shovels. Even though miners’ health and safety has improved over the years, mining is still one of the most dangerous occupations. Mining was traditionally a low tech industry. It is now driven by competitive pressures to go high-tech by using programmable electronics (PE) for machine control, atmospheric monitoring and material processing. The industry’s experience with the functional safety of PE is limited compared with other industries. Thus, PE is an emerging technology for mining that can potentially create or worsen hazards.

Jan 1, 1999

By Lewis PJ, Halfpenny R, Craighead GA

Exploration drilling by Joint Venture partners CRA Exploration Pty Ltd and Elders Mining PNG Pty Ltd has discovered a signif- icant copper and gold deposit at the Wafi River prospect, 60km WSW of Lae in Papua New Guinea. An indicated resource of 18Mt at 2.5g/t Au using a lg/t cutoff has been delineated in Zone A. No estimate has been determined for the separate copper occurr- ence at Rafferty's Zone but the copper will be significant to the project. Metallurgical studies on the gold indicate that the primary ore is refractory to direct cyanidation giving a highly variable and inadequate response. All conventional refractory ore oxidation techniques perform well on both ore and pyrite concentrate and oxidation occurs rapidly. No metallurgical studies on the copper mineralisation have been undertaken. Hypogene covellite and chalcocite copper mineralisation is associated with an intensely quartz-stockworked, and quartz and alunite-altered intrusive. Economically significant gold mineralisation occurs in distal subhorizontal lenses, within a sedimentary host, that plunge toward the intrusive. These lenses are sandwiched between overlying quartz and alunite-altered zones and underlying quartz and smectite zones in a mixed zone of quartz, dickite, kaolinite and illite alteration. The alteration and mineralisation is classified as a high sulphidation, epithermal style resulting from the influx of hot, acid magmatic fluids. Preliminary land ownership, road access, power supply and mine infrastructure studies are in progress. The project is currently at an advanced exploration stage.

Jan 1, 1991

By M. Schreiner, J. Brune, D. Theisen, C. S. -J. Tsai

This study reports that routine mining activities could produce a high number of nanometer sized particles which have not been well characterized and may represent an unacknowledged exposure present in the mining environment. A preliminary survey of the particle emission from the feed-leg drilling activity was conducted in the excavations of an experimental mine. The level of particulate exposure was monitored by real time direct reading instruments include a NanoScan scanning mobility particle sizer (measurement range 10-420 nm) and an optical particle sizer (measurement range 0.3-10 μm). Particulate morphological and structural examination was conducted through transmission and scanning electron microscopy and x-ray dispersive analysis of samples collected by a thermophoretic sampler, and a novel nanoparticle sampler. The real time instrument data revealed high concentrations (> 3.5 x 106 particles/cm3) of ultrafine/nanoparticles generated from the drilling activity. Analysis of particle sampler specimens with energy-dispersive x-ray spectroscopy showed a large amount of submicron silica, spherical primary particles and agglomerated soot particles rich in carbon. Exposure to particles in the nanometer size from various sources within the mining environment may be associated with the poorly understood rise in respiratory and systemic disease among miners. INTRODUCTION Exposures to mine dust have been measured and evaluated for decades. Exposures to aerosolized dust such as coal or silica particles can cause lung and other diseases (1-7). One way that The Mine Safety and Health Administration (MSHA) characterizes inhalation exposures within the mining environment is through measuring the respirable dust mass concentration within the breathing zone of workers (8). Respirable particulate matter (RPM) is of great concern due to its ability to deposit in the alveolar region of the lungs (9-10) where it can affect respiratory function. Interventions championed by MSHA have greatly reduced the prevalence of coal workers pneumoconiosis (CWP) and progressive massive fibrosis (PMF). Although great progress has been made, the prevalence of CWP and PMF appears to be trending upwards and the measured increase in prevalence is not elucidated in RPM measurements (11-12). Though the presence and risk associated with ultrafine particles such as emission from diesel engine within the mining environment has been previously established (13-14). There is suspicion within the mining industry that this resurgence of lung disease may be due to very fine particulate matter from various source that is not properly characterized by current sampling methods. Nanometer sized particles, in the range of ultrafine particles, fall within the RPM size range and have been found to deposit in all regions of the respiratory tract (15). Nanoparticles are commonly accepted as particles that are greater than 1 nm in two or three dimensions but smaller than 100 nm (16). Once in the lungs, nanoparticles can enter the blood stream (17) and selectively affect other target organs such as the heart, liver, bone marrow, lymph nodes, spleen, and brain (15,18-19). The size of nanoparticles has been shown to correlate with their translocation behavior on secondary target organs (20-21). There is strong evidence that the clearance mechanisms used to rid the lungs of particulate matter are not as effective on nanometer sized particles, leading to a greater fraction of never-cleared particles which may enhance disease development (20). Research has demonstrated that nanometer sized particles have unique properties (22) whose adverse health impact is greater than what has been found with micrometer sized particles of the same type (23-26). The large ratio of surface area to mass compared to larger particles is believed to make nanoparticles a greater hazard. Utilizing mass to measure these types of exposure will be very difficult to accurately characterize the quantity of

Jan 1, 2019

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By Joseph L. Margin

From a stubborn start to record setting performances in little over a year, that is the story of the English Running Tunnel Boring Machines. The program to transfer technical information on these highly advanced machines from builder to user will be discussed as a vital link to this accomplishment. Some interesting features of these machines will be covered as well as a recounting of the various conditions that were encountered during these drives and how they were resolved.

Jan 1, 1991

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By J. Allan Tice

In the past fifteen to twenty years, the use of drilled piers to support high capacities in coastal plain deposits has become more and more common. With improved construction techniques and better understanding of pier behavior, drilled shafts with capacities of 200 to 500 tons are not unusual. The purpose of this presentation is to review several drilled pier installations from North Carolina to north-east Florida as a means of illustrating the different types of design concepts and installation techniques which are presently being used. ACKNOWLEDGEMENTS The information in this presentation was obtained from work performed by many individuals and companies. The section on limestone socket caissons in South Carolina is an abridged version of a paper prepared by Rob Smith and Neil Gilbert of Law Engineering's Charlotte, North Carolina office, and is used with permission. The section on pier installation in northeast Florida is an abridged version of a paper prepared by Kirk Mcintosh, Tom McDaniel, and Randy Knott of Law Engineering's Jacksonville, Florida office, reprinted here with permission. Additional data discussed in this presentation has been obtained from Farr Foundation Company, McKinney Drilling Company, and Peterson Drilling Company.

Jan 1, 1988

It is now five years since the advent of gold-dredging in Australia, the State of New South 'Wales, or colony as it was, being the first to adopt this system of gold-getting, and the credit of its introduction rests with a member of this Institute, Mr. Chas. L. Garland, who commenced operations with his dredge on the Macquarie River, at the junction of the Muckerawa Creek, in the month of March, 1899. In this paper it is intended to give a brief history of the career of the gold dredge in New South Wales from that relate up to the present time, during which period the writer, as a designer of many dredges, has been constantly in touch with the subject in all its phases in this State; the points noted are the outcome of his observation in a general way, and to a great extent are apart from the design proper.Gold-dredging in New South Wales up to the present moment can hardly be designated an unqualified success...

Jan 1, 1904

By N. A. D. Parlee, M. M. A. El-Naggar, G. 8. Horsley

The apparatus was of a modified Sieverts type1&apos;2 with a reaction tube designed to function also as the cell component of an oxygen pressure gage. The reaction tube assembly is shown in Fig. 1 and described in Table I. The main body is a 1-in.-OD 15 mol pct calcia-stabilized zirconia tube. The ground-glass joint, g, the male part of which carried a prism for optical pyrometer use, was connected to the remainder of the Sieverts apparatus. The calibration of the cell (at its 1000°K operating temperature) for internal oxygen pressures (PO2in) in the range 0.2 to 10 9 atm was made against internal air pressures measured by mercury manometer and McLeod gage. At very low po2in values down to l<Tn atm the performance was checked by comparing pQ calculated from electromotive force measurement when the apparatus was filled with a) pure CO gas and b) a CO-CO2 mixture of the ratio CO-CO2 = 1:0.398, with Po, values calculated from the equilibrium constants of the following reactions at 1000°K:

Jan 1, 1968

The recovery by flotation of some complex uranium minerals such as brannerite and davidite is described. Anionic reagents used for flotation of iron and titanium oxides&apos; are suitable. If care is taken, to emulsify the reagents the slime fractions may be satisfactorilytreated.INTRODUCTIONUranium ores are usually treated by direct leaching with acid or alkali according to the nature of the gangue materials. Concentration of the uranium minerals prior to leaching is not commonly practised because of the earthy nature of most uranium minerals and the difficult mineral dressing problem they pose. Some of the harder complex oxides such as davidite and brannerite are amenable to flotation. This is fortunate since they usually require an expensive, strong acid treat~ent to dissolve the uranium. Flotation tests were commenced in 1949 by officers of the South Australian Department of Mines stationed at Adelaide, first in the School of Mines, then in the University of Adelaide and finally in Departmental mineral dressing laboratories at Thebarton. Separation of daviditefrom Radium Hill and Mount Victoria ores, brannerite from Crocker&apos;s Well ore, and secondary uranium minerals from Myponga ore was attempted.The development of the flotation reagents to separate the oxides from silica and the silicates is first described, then some of the results obtained are presented as tables.DEVELOPMENT OF FLOTATION REAGENTSThe davidite at Radium Hill is associated with iron and titanium oxides, qu;a,rtz and biotite as replacement deposits in shears. The davidite, rutile,&apos; ilmenite and hematite usually occur in segregations from nut size to masses of several pounds. They are associated as a complexity of...

Jan 1, 1955

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By Hans von Michaelis

"INTRODUCTIONThe renaissance in gold and silver recovery technology has continued to unfold and it is appropriate to review some of the useful new technologies as well as try to identify some of the industry's future needs and frontiers.The remarkable strengthening in the US dollar has resulted in a relatively low gold price in US Dollars of around $310/oz at the time of writing and silver at $6.25/oz. This general softening in the dollar prices and the recent confusion as to environmental compatibility of cyanidation tailings and effluents, has led to a slowdown in announcements of new operations. Another reason for the slackening off in the USA is that in the past few years a large part of the capital has come from oi I and gas companies that now seem to be losing interest in mineral ventures, and foreign investors for whom the dollar is becoming out of reach. In the author's opinion this represents an unprecedented window of opportunity.Elsewhere in the world where local currencies have weakened, the price of gold is at or close to its all time high.For example, in South African Rands, the gold price was R571.00/oz when the rand was US$1.47 and the gold price reached US$800. Now at US $309/oz and with the Rand at US$0.51 = Rl .00, the local gold price is R600. The price of si Iver in Mexican pesos is not much less than it was when silver reached US$50/oz. Gold, and silver prices in local currencies outside North America are still buovant and at levels where additional investment in new projects is more encouraging.Even in Canada where the dollar is worth about US$0. 75, this provides a smaller but significant cushion compared with US operations. Considering the present strength of the US dollar and even the Canadian dollar relative to many other gold producing countries, there should be significant investment opportunities at today's prices. Mining companies have started to descend on Brazil, for example, where in a matter of just a few years annual gold production has increased from 10 to 70 tons. In South Africa, a Canadian company backed by Swiss financing has been able to take over a Witwatersrand gold mining operation and is installing a huge new tailin9s retreatment plant to process about 1 million tons per month of tailings."

Jan 1, 1985

By L Matthews, D O’Dea, P C Hayes, J Manuel, B Monaghan, T Honeyands, D Pinson, J Leedham

Many different approaches have been used in the past to characterise iron ore sinter mineralogy to predict sinter quality and elucidate the impacts of iron ore characteristics and process variables on the mechanisms of sintering. Characterisation techniques include optical image analysis and point counting, X-ray diffraction and scanning electron microscopy. Each technique has its advantages and disadvantages depending on the objectives of the measurement. It is generally acknowledged that silicoferrite of calcium and aluminium (SFCA) is very important to the quality of the sinter produced; however, strict definitions of the phases and textures of SFCA are not generally agreed. This paper summarises the state-of-the-art in sinter characterisation applied in Australia by both academics and industrial researchers. The results from various techniques are compared and the relationships between the measurement results are discussed.CITATION:Honeyands, T, Manuel, J, Matthews, L, O’Dea, D, Pinson, D, Leedham, J, Monaghan, B, Li, H, Chen, J, Hayes, P C, Donskoi, E and Pownceby, M I, 2017. Characterising the mineralogy of iron ore sinters – state-of-the-art in Australia, in Proceedings Iron Ore 2017, pp 49–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015