Search Documents

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

It is estimated that the tailings dam of the Mouteh Gold Mine, in Iran, contains more than 770 kg of gold. Microscopic analysis reveals that sulphide minerals and active carbon are the main sources of the gold in the tailings residue. Flotation and cyanidation tests on the samples of tailings were conducted. Flotation concentrates, containing around 87.79% of the gold, which were associated with sulphide minerals, were recovered. By regrinding, roasting, and cyanidation of the flotation concentrate, the gold dissolution recovery was in the range of 87.8 to 98.4%. The carbon-in-column method was used to recover 98% of the gold from the solution. Keywords: gold ore, pyrite, flotation, roasting, cyanidation

Jan 1, 2009

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

NATURE OF ORETHE Edna May ore consists mainly of clean quartz of a moderately hard and tough nature. The gold content is "free" and fairly coarse, so that a large percentage is recovered by amalgamation. The ore is practically free from metallic minerals.GENERAL OUTLINE OF PLANT AND TREATMENTThe ore, received from underground in trucks, is broken by a jaw breaker, then stamp-milled, follow~d by partial filie-grinding in pans. Mercury is used both in the mill boxes and pans. The pulp, on leaving the pans, passes over amalgamating tables and is then elevated by tailings pulp to cone classifiers and separated into a sand and slime product, each product receiving a separate cyanide treatment-sand by leaching in vats and slime by agitation and decantation in a "Trent" plant. Gold solutions from both sand and slime are precipitated together by zinc shavings in the usual type of precipitation boxes. Accumulated slime is trucked from the dam to a vortex mixer and from this point receives with the cement slime the same treatment.ORE BREAKING AND TRANSPORTThe ore is trucked from the brace of the shaft along an overhead line to the breaker station. Hence it is, by means of a "kick-up" dumped upon a grizzly, set with 2-in. spaces, the oversize being broken by a 15 x '9 Fraser and Chalmer jaw...

Jan 1, 1919

By R. Mensah-Biney

The NC State University Minerals Research Laboratory (MRL) and Waste Reduction Partners (WRP) of the Land of Sky Regional Council joined efforts in 2000 to initiate a technically sound and practical program for the management of high-volume coal combustion by-products (CCBs) in North Carolina. The accumulation of CCBs from coal burning boilers throughout the state of North Carolina posed a substantial storage problem, and the area was overripe for an effective management program, which would be environmentally sustainable. In particular, the public utility generators had filled storage ponds on their properties, and the storage overload had grown to critical proportions. Much the same situation existed for paper mill biosolids, which were stored on site in landfill cells along with daily output of CCBs from the mill boilers. A conversion process via the patented pyro-process12 (US Patent No. 5,342,442) to produce synthetic light weight aggregates (LWA) from CCBs and paper mill sludge was conceived to process large quantities of both these waste materials. MRL and WRP initiated and formed a consortium that brought together academia, private industry and state agencies to evaluate the production of LWA by the pyro-process. The industry partners included representatives from the power companies, industrial ash generators, expediters for coal ash products, as well as concrete block manufacturers. It was important to welcome interested parties from not only the western North Carolina area and other parts of the state but also from neighboring states including Tennessee, South Carolina and Georgia. Membership of this consortium evolved during the intervening years to include the following participants and supporters: Progress Energy Carolinas; Duke Energy; Santee Cooper; Full Circle Solutions; Land-of-Sky Regional Council; NC Department of Pollution Prevention and Environmental Assistance; Ecusta Business Development Center; Blue Ridge Paper Products; Jackson Paper and Manufacturing Company; Miller Perlite; Appalachian Products; General Shale Brick; Metromont Materials; Small Business Technology Development Center of the University of North Carolina system and North Carolina State University The initial development program conducted at the Minerals Research Laboratory (MRL) was to formulate an acceptable LWA product, which fulfilled user specifications for light weight concrete block and structural concrete application. Support work and program coordination efforts were furnished by retired technical volunteers in WRP. The work advanced steadily, using proven technologies well established in the mineral industry, to generate a very satisfactory LWA. The consortium then concluded that a more comprehensive CCB conversion program would have more appeal for full scale manufacture and commercialization, if a variety of products from CCB separation were generated. This product assortment would include bottom ash, low carbon fly ash, recovered carbon of high purity, as well as the synthetic LWA. The bottom ash would serve the concrete block market, the fly ash was in demand for ready-mix concrete, and the high carbon product could be pelletized and used as a fuel for reburn or by the steel industry, and the LWA was a sought-after component for light weight concrete applications. After scouting all these potential markets and finding them to be viable, the consortium then inaugurated an integrated pilot plant program for the CCB separation and conversion. The plan was organized in three (3) parts: (1) Phase I ? bench scale evaluation studies (2) Phase II continuous pilot plant evaluation and (3) Phase III ? conceptual commercial plant design including marketing efforts and attraction of business entrepreneurs to build a full scale manufacturing plant. Phase II would serve to validate the process in a continuous mode and produce substantial quantities of products for preliminary marketing efforts and for demonstration-of-use purposes. The consortium agreed to the name, CAROLINA ASH PRODUCTS, (CAP), for the integrated pilot plant program. The products generated might be designated with the CAP label as: bottom ash would be named CAP Granules, low carbon fly ash would become CAP Ash, recovered high carbon product would be CAP Carbon, and LWA would have the name CAP Stone. Phase II of the program processed 20 tons (18 t) of ponded ash from Progress Energy storage at a rate of 600 lb (271 kg) of raw ash per hour with favorable results. PRELIMINARY STUDIES Prior to committing laboratory research and development effort as well as support and coordination activities to this program, it was necessary to determine (1) the level of need for a freshly launched CCB reutilization program in this state and (2) what degree of versatility was necessary for such a process. State agency records and a survey of recent boiler operations indicated that in the state of North Carolina at least 77 facilities manage CCBs from their boiler operations. Despite continuing development efforts in more eastern parts of the state, the use of CCBs for commercial applications has not increased to a level which alleviates the need to store vast quantities in private monofills on the generator?s property. More than 1.25 million tons (1.13 million t) of CCBs are landfilled in NC annually, with 300,000 tons (271,985 t) per year generated in western NC alone. Many different boiler types, which span both very old units and those that are modern and efficient, were to be found. These included stoker-fired units, pulverized coal boilers, slag-tap furnaces, and fluidized bed combustion boilers covering a range of sizes. Any systems designed to separate CCB components from all these sources and convert them to useful secondary products would need broad processing latitude and flexibility. Up to the present there has been a paucity of research done in the western part of the state to find productive alternatives to storage in landfills. With tipping fees in our largest landfill now approaching $40 per ton ($44 per t) and escalating transportation fees (about $200 per truckload up to 40 tons, traveling a distance of 25 miles), the problem has become urgent both economically and ecologically. A well-designed, integrated wet process for CCB separation into value-added products had much potential to be less expensive than landfilling as well as to provide saleable materials with acceptable profit margins. These preliminary investigations also revealed that other major waste streams, in particular paper mill sludge and municipal and animal waste biosolids were important candidates for priority attention. Since these biosolids could furnish the organic component of a synthetic LWA product, they could be consumed as part of the same program. This added interest value to a growing list of partners to support and participate in the program.

Jan 1, 2009

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to develop a mathematical model of cable bolt support systems. Part 1 described laboratory studies of the support properties of conventional steel cable bolts. Part 2 describes the strength characteristics of conventional cables with steel buttons, single and double birdcage cables, and epoxy-coated cables.

Jan 1, 1991

By David C. Girard, Larry Williamson, Leonard R. Benson, Ronald E. Bizzarri

On the east side of Washington DC, the DC Water & Sewer Authority is developing a Facility Plan for the Anacostia River CSO Control Projects, including 8 to 12 miles of CSO storage/conveyance and flood relief tunnels and associated facilities. The project includes major technical and non-technical challenges, including: completion under a Federal Consent Decree schedule; large diameter (estimated 25 to 35 ft) soft ground tunnels and shafts up to 200 ft depth; operations without use of active flow control systems; and close coordination with several major public and private construction and development projects that are being advanced in the project area.

Jan 1, 2007

By L. M. Adams

Experiments in reclaiming acidic surface-mined coal lands with raw fly ash from bituminous-coal-fired powerplants were conducted by the Bureau of Mines at two sites in northern West Virginia. Plots at both sites were treated with varying tonnages of fly ash from three area powerplants and were planted with a variety of grasses, legumes, trees, and shrubs. Eight grasses and seven legumes were investigated. Greatest promise for growth under harsh soil conditions was shown by Kentucky 31 fescue, rye and red top grasses, and birdsfoot trefoil, a legume. Survival of trees and shrubs was negligible. Addition of fly ash to the spoil increased the pH to a range tolerable to some types of plant growth, improved the texture of the soil, and increased the available water of the resulting mixture.

Jan 1, 1971

By H Saw, M Cordova

Cemented rock fill (CRF) is often used to support open stope voids. This allows for the full recovery of ore while achieving global mine stability. In such cases, the exposed CRF masses require adequate compressive strength and stiffness to resist the forces and limit the displacement associated with movements in the rock mass surrounding the excavations. The CRF material preparation often involves the use of large particles, either from crushed rock or development mining waste. This means that conventional laboratory samples cannot be readily used to determine the laboratory strength. Consequently, a research project was undertaken to determine the influence of sample size on uniaxial compressive strength. This paper presents the results from CRF samples that were prepared using the same mix design and then cast into moulds with diameters of 150, 240, 300 and 400 mm. The laboratory testing also allowed a better understanding of the effect of particle size distribution upon the overall strength of a rock fill mass. The laboratory results were compared to a database of large-scale results from the testing of fill masses from a number of mine sites.CITATION:Cordova, M, Saw, H and Villaescusa, E, 2016. Laboratory testing of cemented rock fill for open stope support, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

Early strategic mine planning includes decisions over the organisation of work and workforce accommodation. These decisions involve significant commitments that affect not only employee quality of life but also the impacts and relationships with existing local communities. Strategies for workforce accommodation are characteristically community-based (either as purpose-built company towns or integrated within existing local communities) or commuter (fly-in, fly-out) mine camps. The quality of accommodation underpins the fulfilment, morale and motivation of employees. This is not only relevant to productivity and safety, but also to recruitment and retention, particularly with the current onset of a significant human resources crisis. In the event that communities exist in proximity to a proposed mine then the accommodation strategy selected can influence the value-adding potential for the sustainable development of such communities. This early planning is particularly challenging where mine locations are isolated and/or face significant economic, social and political adversity. This paper draws upon a case study review of five large mining projects implemented in three South American countries, selected to cover a range of scenarios and accommodation strategies. The review aims to advance our understanding of the complexity of the underlying planning issues. Each scenario considered the prevailing environmental, social, economic and political situation, together with the adopted accommodation strategy. The case study review aimed to identify lessons learned and to make recommendations for advancing mineworkersÆ accommodation planning practice.

Jan 1, 2006

Ore from the "Staimite" lode in the Oonah mine, Zeehan, has a complex composition and contains an exceptional number of elements. Its chemical composition has been indicated by the following published figuresà

Jan 1, 1931

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By S Speed, N Corlis, A Goldstone, G N. Browne, M Fitzpatrick

In 2005, Solid Energy New Zealand Limited obtained non-notified consent for the disposal of 1Mt of coal ash at the Rotowaro minesite, forming part of a coal supply agreement with the Huntly Power Station. A non-notified resource consent was sought which necessitated that environmental effects be shown to be æless than minorÆ, and resulted from robust science and a pragmatic approach to design. As part of the assessment of environmental effects, there was a need to understand the effects of boron concentrations on aquatic organisms (ie algae, plankton, plants and invertebrates) in the receiving environment. Boron is a naturally occurring element that is found in the form of borates in the oceans, sedimentary rocks, coal, shale, and in some soils but Waikato coals and ashes have particularly high boron content. Boron is an essential micronutrient for higher plants with interspecies differences in the levels required for optimum growth. As aspects of the ANZECC (2000) derived boron limits are based on toxicity of aquatic algae and plants to boron it was important to assess these components in the environment. The effects on the receiving environment of the Awaroa Stream were assessed using predicted water chemistry and comparing actual boron concentrations in a comprehensive and multifaceted reference-condition approach of catchment ecological indicators. In addition a toxicological-based assessment of boron and a re-calculation of the ANZECC trigger levels were undertaken and applied to the ecological indicators. The reference-condition approach revealed that habitat and overall water quality attributes at and between sites was more influential in determining the aquatic biotic communities than boron concentrations alone. There was no evidence of any gradient of changes in ecological indicators with changing boron concentrations, nor evidence of any residual effect of high historic boron concentrations on the aquatic biota.

Jan 1, 2006

By Frederick G. Clapp

SINCE oil journals commenced to feature the progress of Iraq pipe-line developments and since newspapers undertook to follow the discussions between a certain large oil company and an Asiatic nation, I have repeatedly been asked questions that are only answerable by setting forth the essential geographic and historical facts of concessions in that part of the world. In so doing effort will be made to correct erroneous statements made in various quarters: and mistakes herein are being kept as low in number as possible. Perhaps the best-known concession in the Middle East is the one of the Iraq Petroleum Co., covering the greater part of the portion of the kingdom of that name- lying east of the Tigris River. West of the stream is the concession of the British Oil Development Co., which takes in all presumed petroliferous areas in western Iraq. No other important oil concessions exist in that country, except for the lands of the Khanikin Oil Co., which operates in "Transferred Territories" on the border of Persia. East of and continuous with the Iraq fields are those of Persia where the Anglo-Persian Oil Co. holds the well-known D'Arcy concession comprising three-quarters of the country, omitting the five northern provinces. This is the only valid existing concession in Persia, so far as known, except certain old firmans that permit development at Semnan in central Persia and possibly also certain regional grants to a French banking syndicate in eastern Mazanderan Province.

Jan 1, 1933

By H. Ipek

Industrial grinding machines used in the mineral processing industries are mostly of the tumbling mill type. These mills exist in various types: ball, rod, pebble, autogenous, and semi-autogenous. Balls and rods are traditionally media shapes used in the tumbling mills. In resent years, as an alternative to balls, grinding charges with various shapes are being used. Cylpebs are slightly tapered cylindrical grinding charges with length equaling diameter, and all the edges being radiused. Cylpebs of equal diameter and length have 50% greater surface area and 45% greater weight than balls of the same material. In addition, they have 9% higher bulk density than steel balls, or 12% higher bulk density than cast balls. An important advantage of cylpebs over balls is that cylpebs produce narrower granulometric distribution due to their shapes. However, some discrepancies were found in the literature regarding the milling performance of cylpebs in comparison with balls (Chi, 2004). In recent studies, Chi (2004) has provided detailed information on cylpebs and has compared these to balls in relation to media mass, size distribution, surface area, and input specific energy. Ipek (2006) has investigated the effects of cylpebs and balls with equal mass and surface area on the breakage rate of quartz, using cylpebs and balls separately. Similarly, Lameck and Moys (2006) have investigated the effects of balls and worn balls on breakage rate of material using worn balls as grinding environment. However, no study has attempted to investigate the effects of grinding environment other than balls on the brekage distribution. As indicated by Prasher (1987), the breakage distribution function is independent of the following variables in ball mills: hold-up (Mika et al., 1967; Kelsall et al. 1969), mill speed and ball load (Herbst and Fuerstenau, 1972), media load and ball density (Kelsall et al., 1973), mill diameter (Malghan and Fuerstenau, 1976), and powder charge (Shoji et al. 1980). The aim of the present paper is to compare the effects of cylpebs and balls on the breakage distribution function of quartz with respect to same mass and same surface area. BACKGROUND Comminution as a rate process is called kinetic approach. Studies on the kinetic approach are reviewed by Oner (2001). Oner states that grinding kinetics are based on studies by Kolmogorov in 1941 and that Robert (1950) is the first to suggest this approach. Later, Melzak, Loeveday, and Reid have improved the grinding kinetics equation; and, Austin and Lynch have conducted two basic studies on the analytical solutions of these equations. Considering the results of studies comparing the size reduction mechanisms, it has been accepted that breakage constitutes of two operations. These two basic operations, first defined by Epstein (1948), are those of selection of material for breakage and the distribution of breakage material to particle sizes smaller than the initial size (Lynch, 1977). Epstein defined the two operations as: ? Pn(y), the probability of breakage of a particle size in the nth step of the breakage process. ? F(x,y), the cumulative distributions by weight of particles of size x<y arising from the breakage of a unit mass of a size y. Probability of breakage is called a selection or a breakage-rate function (Si). Characteristics size distribution after breakage is called a breakage distribution or appearance function (Bi,j). Due to the difficulties in representing particle size distributions mathematically and constantly, the batch equation based on particle size fraction is suggested. Thus, as is the case in breakage distribution and specific rate of breakage, the breakage parameters were defined by batch grinding experiments conducted in laboratories (Oner, 2001). When effective breakage occurs in the mill, the breakage of material with single feed size fraction usually fits first order grinding kinetics and the specific rate of breakage values can be calculated through the slope of semi-log plot. The values of the breakage distributions are deduced from the size distributions at short grinding times where there is mainly size 1 material breaking and only small amount of smaller sizes to rebreak (Austin et. al., 1984). B values can be calculated by using BII. [ ] where j is the top size of the charge, Pi(t) is the cumulative percent undersize of i th size interval at the short grinding time which gives no more than about 30% broken out of the top size interval. Cumulative primary breakage distribution, Bi,j, is also defined in an empirical form by [ ] where xi is the top size and Bi,j is the weight fraction of primary breakage products. The parameters F, ? and ß define the size distribution of the material being ground. On plotting size versus Bi,j on log scale, the slope of the lower portion of the curve gives the value of ?, the slope of the upper portion of the curve gives the value of ß, and F is the intercept as in Fig.1. [ ]

Jan 1, 2009

THIS has been a much-neglected branch of engineering. With the majority of industries labour is the chief item of trouble and expense. Anything that will reduce trouble and increase efficiency is well worth considering. It is only of recent years that any attempt has been made on a scientific basis to improve conditions sporadic attempts having been made from time to time, privately and by law. Some have been successful, others unsuccessful not necessarily the fault of those who initiated the ideas, though naturally mistakes were made in some cases for want of experience, but those whom it was desired to benefit were not always prepared for the change, and by their distrust hampered schemes instead of assisting them.Man power is generally more expensive than machinery, though there are exceptions, such as when a small amount of work has to be done in a place where machinery does not exist, and it would not pay to instal any or where labour is cheap, and skilled workmen are scarce as in some tropical countries. When machinery is first introduced it generally causes the suspicion that it will deprive men of their work. It may cause men to vary the conditions of their work, and in some individual cases, when men are unable to conform to changed circumstances it may result in a certain amount of hardship; but, after all, the less competent must not hold back progress for the general good. Besides, changes as a rule do not take place suddenly, so old hands can generally find work at their particular calling &apos;till nature requires them to retire. In cases where men take to machinery, they not only find that they are relieved of the...

Jan 1, 1918

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By Kennedy G. L, Evans D. G

The development of the carbonization of brown coal briquettes to produce a hard char suitable for use in place of imported hard coke has continued in Victoria, and an experimental carbonization plant has recently been commissioned at Morwell by the Gas and Fuel Corpora.tion to assess the prospects for the commercial production and marketing of hard char in Victoria. The char offers advantages in its very low ash content and its uniform lump size, while the indications are that it could be marketed at a price competitive with that of imported hard coke. The hard char is unique amongst metallurgical fuels in combining a high reactivity with high physical strength, and research by the University of Melbourne into its utilization in foundry cupolas for melting iron has shown how modifications could be made to take advantage of these properties. An 18 inch experimental cupola has been built to test in practice the predictions made from this fundamental research.INTRODUCTIONSteady development has continued in Victoria from the promising laboratory researches at the University of Melbourne which were reported to the 1955 Annual Conference of The Institute (Worner, 1956). This work had shown that a hard lump char could be produced by the high temperature carbonization of standard industrial briquettes by careful control of the heating conditions, and that the special briquetting techniques adopted in Germany were unnecessary with Yallourn brown coal. Continuation of this research has led to the refinement of carbonization techniques and has increased the strength of the char until it has equalled that of conventional metallurgical cokes.

Jan 1, 1960