Search Documents

By Glenn C. Waterman

The use of stream sediment and soil sampling as an aid in exploration has markedly increased in recent years as more and more attention has been directed to areas that are generally geologically favorable for mineralization but show little outcrop. Numerous ore deposits and many hundreds of mineral deposits that have no surface exposure have been found associated with anomalous geochemical patterns. Sophisticated techniques have been developed to "wring out" of geochemical data subtle information that is pertinent in defining areas of exploration interest. Variations in metal patterns in soils and sediments as they are affected by pH, Eh, weather, topography, etc., are pretty well known. Field studies have determined the variations and controls of metal ion distribution in the several soil horizons and the contributions to metal concentrations made by different types of vegetation. Less well known is how to interpret geochemical data since thickness of soils over bedrock varies in an unknown fashion and, particularly, where glacial debris of unknown thickness is piled on top of soils or scoured bedrock.

Jan 7, 1975

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By B Crossley

Self-cleaning fluidised bed heat exchangers have demonstrated unparalleled performance internationally for the implementation of indirect heat transfer in severely fouling fluid environments. Recent advances in equipment design have increased the scope of application to include indirect heat transfer in slurry environments, including fouling, scaling and viscous slurries. The ingenious configuration of recirculated cleaning particles through the tubes of vertical shell and tube heat exchangers provides the ability to solve heat transfer problems that arise as a consequence of tube-side fouling during indirect heat transfer to process fluids or slurries. In most cases, the cleaning particles consist of chopped metal wire, however other process-specific materials may be used.

Jan 1, 2004

By O Pasca, B Hogg

Consistent slag blow end point detection remains one of the challenges in the Peirce-Smith converters at Mount Isa MinesÆ Copper Smelter. Under blowing results in foaming on copper blow and carry forward of oxide skims to the anode furnace. Over blowing results in high copper losses to the slag. Both present safety issues and contribute to lower copper production. The end points of the slag making phases are assessed by inspection of a bar sample. A bar sample is a thin accretion layer that adheres to a steel bar when it is inserted into the tuyere while the converter is blowing. This method is biased and subjective, so there is heavy reliance on operator experience. The Semtech Optical Process Control (OPC) system was installed in early 2002 for converter slag blow end point detection. Initial plant trials did not improve all aspects of converter operations, and uptake by operators was poor, so the system was not used. In early 2005, the Semtech OPC system was re-visited and another short trial was conducted to evaluate the permanent use of the system for slag and copper blow end point detection. During this trial, the Semtech OPC method was found to be superior to bar sampling for slag blow end point detection. The implementation and refurbishment of the Semtech OPC system has resulted in plant improvements and given a better insight into converter operation during blowing. Oxide skim generation carried forward to the anode furnace has been shown to decrease with increasing compliance with Semtech OPC. Some of the expected improvements to converter operation were not found to be significant. Semtech OPC is now well received and utilised by converter operators. Individual paper available only. Not included in book or CD ROM Proceedings.

Jan 1, 2005

By T Soares, P Esteves, C Senna, V Souto, E Dias

Steinert provides a wide portfolio of Sensor Based Sorting (SBS) technologies, including the possibility to combine different sensor data in the development of the separation applications. This multi sensor approach provides a larger applicability and extensive flexibility for the technology. This effect is emphasized for mining applications, once every ore body presents its own features that can also comprise a large material variability. In this sense, every sorting application is customized and comprises a personalized solution. This means each project development includes a test work stage that approaches from the project discussion, test definition, up to test outcomes and processing development. In relation to very complex and large projects, a sorting pilot scale plant has become a crescent tendency. By having a pilot plant stage can represent a chance to test larger amounts of material from different mining areas, different mining projects, such as to consider different processing targets and application approaches. Based on that, a better understanding about the technology application can guide a more assertive development of large and complex ore sorting projects. The aim of this paper is to provide information about the applicability of the Steinert multi sensor technology at different pilot plants in South America. It consists in a compilation of laboratory test results, plant design and operational results. For that, a chromite, an IOCG deposit and a sulphide gold ore projects are presented. Additionally, the paper discusses the application of different sensor technologies combinations such as various processing targets, thus providing a wider understanding about sorting applications and flexibility.

Nov 10, 2020

By J. H. Qian

China is one of the countries with comparatively wide distribution of soft soil. In the wake of the rapid developement in the national economy and construction, the improvement technique of soft soil foundation has been perfected gradually. At the present, an integrated system of soft soil improvement has formed, features of such a system are shown by the variety of improvement methods, the complement of theoretical study to project practice. This paper summarizes mainly the following methods: lime column, vertical drain, vibroflotation and dynamic consolidation.

Jan 1, 2010

By Jifan X, Yongyu W, Liangjing L

Shallow interception of groundwater is a special dewa- tering form in the specific geological and hydrogeological conditions. It has an economic and technical effect. The roof of the Fankou Lead-zinc deposit is the Hutianqun aquifer made up of the limestone of the upper Carboniferous system. - A "water-bearing basin" is surrounded by the aquifuge and the aquitard below ¦0 m level at the Shiling Hill section in the Hutianqun aquifer. Based on the natural conditions, an interception gallery is excavated at -40 m level out of "the water- bearing basin", the other gallery excavated at ¦0 m level in the poor water-bearing zone of the Jinxing Hill. During 20 years of experience, the better interception effects have been gained.

Jan 1, 1988

By Gang Chen

This paper explores the possibility of using short-term time-dependent plate loading tests to estimate the elastic and viscoelastic parameters of the weak floor strata typically associated with coal seams in Illinois. Plate loading tests with incremental loads, similar to incremental creep experiments, were conducted until the floor failure occurred. For each increment, the load was held constant for a period ranging from 1-4 hours until a constant deformation rate was achieved. The deformation-time data were analyzed for viscoelastic parameters of weak floor strata assuming its behavior to be adequately represented by the standard Burgers model. The analysis required development of mathematical equations for the time-dependent deformation of the standard Burgers material under a three- dimensional state of stress. Time-dependent pillar settlement data at one mine were also analyzed for elastic and viscoelastic parameters of the weak floor strata using the developed equations. These parameters were compared with similar parameters estimated from plate loading tests.

Jan 1, 1990

By D. P. Venter

When Oryx Mine down-scaled in 1994, focus was placed on development, with the primary aim being the exposure and proving of ore reserves. In order to achieve this aim, development ends had to be advanced to reef at the maximum possible rate. This in turn called for support methods which could keep up with the advancing faces, taking up minimum space and time for installation, while providing on the face a real coverage and effective long-term support. In the majority of the development ends which were located in fairly competent ground, the grouted rod development support proved to be adequate until such time as secondary support in the form of meshing and lacing could be installed. The ends developing towards the eastern boundary of the mine, especially in the ?C? block, encountered extremely adverse ground conditions due to the presence of smectite zones within the footwall quartzites. Smectites are a group of montmorillonite clay materials, mainly composed of hydrous aluminosilicates. They occur as minute platy crystals in the rock mass and are especially notable for their ability to absorb liquids. Generally, the zones are found in between the bedding planes of the host rock, and may vary considerably in thickness over short distances. Wherever the smectites were exposed by the development blasting, the rockwalls weathered as the smectites absorbed water and the condition of the tunnel rockwalls deteriorated rapidly. When the smectites were left exposed and allowed to weather, it became almost impossible to install secondary permanent support such as meshing and lacing at a later stage. To minimise the exposure time and subsequent deterioration of the smectite zones, it was recommended that all development ends encountering smectites be shotcreted as soon as possible after blasting. In developing a shotcreting support methodology, both a drycreting and wetcreting system were investigated. The situation at the time ruled out the use of a wetcreting system on the basis of the extensive and costly infrastructure required, as well as its limited manoeuverability. Instead, it was decided to opt for as maller scale but more manoeuverable drycreting system. The system utilized a number of portable drycrete machines with pre-bagged cement, which could support several development ends in close proximity. Initial trials using normal 30 MPa shotcrete on 19level proved successful and the system was implemented.

Jan 1, 1998

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By A K. Ghosh

"Inrush of water is always an issue, especially for mines located in heavy rainfall areas. Nowadays, mining companies and research institutes have developed many advanced technologies for study and analysis of hydrological processes. In this paper, an advanced method is introduced, which uses the Shuttle Radar Topography Mission Digital Elevation Model (SRTM DEM) data in the Geographical Information System (GIS) platform to simulate the stream distributions around two specific mines: Super Pit and Griffin coalmine in Western Australia. The impact of this approach is important because it reduces the time and economic cost by creating a high spatial resolution hydrological map in the specific areas. The study identifies the flow path of the run-off water, which helps in adopting a suitable water management plan surrounding the case study mines. The results match with the ground reality. Based on the results, the stream structure around Griffin coalmine is more complicated than that of Super Pit. The bifurcation ratio and drainage density are computed to estimate the subsoil permeability characteristics of the two mines. Recommendations have been put forward to prevent and reduce the potential risks of water accumulation around the open pit mines.Citation:Ghosh, A K, 2016. Application of Shuttle Radar Topography Mission Data in Hydrological Analyses of Super Pit and Griffin Coal Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 162–169 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Charles H. Bucknam

A gold sampling optimization study was carried out in support of open pit gold mining operations for the Newmont Gold Company Bootstrap-Capstone deposits in Northeastern Nevada. Six bulk samples were tested using fire refining techniques at field particle size, to determine coarse particle heterogeneity of the ores, and by gravity .concentration methods at 10 mesh particle size, to observe any particulate gold liberation. An overall sampling model is presented for the deposit based on the pooled test information, to reconcile the results of coarse particle heterogeneity testing and the fine particle 'liberation testing. The sampling model is used to recommend procedures to control the variability of gold grade estimation due to the fundamental error (nugget effect) during sampling, sample preparation and assaying of the ores and other fundamental variances. The technique of simplified quantitative risk analysis (SQRA) is used to provide an economic justification for implementation of. recommended improvements to field sampling practices.

Jan 1, 1999

By Katherine Hynard, Colin Eustace

Suboptimal decisions introduced during the mine planning process are generally a consequence of both a myopic view of planning objectives as well as time and resources available to convert longer-term plans into execution plans. Erosion of strategic mine plan value in conversion to execution plans is likely to amount to billions of dollars each year. When integrated with operations data feeds, simulation and optimization tools can be used to preserve the value in the strategic mine plan. Optimization models are capable of both automating production of execution plans and improving performance. This reduces the manual burden of revising plans while improving alignment with long-term production objectives. Simulation models can also support the process of developing effective execution plans by providing forward visibility of mine operations performance. They can also be used to test the robustness of optimized execution plans and response to operational variability and disturbances.

May 1, 2025

By N. Kuroda

A realistic simulation model has been used for designing longwall mining, especially for solving operational problems. This paper describes background, development, validation and some applications of the simulation model for mining people who are unfamiliar with O.R. or computer technique, as a simple planning tool. The following items were established: logical analysis and algorithmic design for practical longwall mining, structure of hypothesis behavioral organism, input parameters, using practical knowledge and operational statistics of the mechanized longwall system experienced for many years.

Jan 1, 1982

By Mahoney BK

The development of simulation models to reflect accurately the operations of a port and its associated transportation systems can be an expensive and time consuming process. However the complexity of such operations leaves little choice for other than simulation techniques since analytical methods are rarely appropriate. The development of suitable software has now reached the stage that these techniques can be used with confidence. Types of simulation models and their requirements are discussed together with the results from some recent applications to the planning and management of bulk terminals.

Jan 1, 1983

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By M. A. T. Cocquerel, J. G. Eacott

"Simulation techniques may be used to optimize existing processes and plant operations, and in plant design at the engineering study stage of a project . This paper describes the latter application, using a computer, to optimize the concentrate stockpile requirements of a modern copper smelter.A large open-pit mining operation is envisaged and it is assumed that copper concentrate is smelted in two flash furnaces. The proposed mining plan gives rise to metaffurgical considerations in smelting which dictate that concentrate blending is carried out in the early years of operation in order to eliminate wide variations in the grade of concentrate charged to the furnaces . Stockpiling facilities are therefore necessary for blending purposes and also to provide a strategic reserve of concentrate to ensure continuity of concentrator and smelting operations.The objective of the study is to determine the optimum size of concentrate stockpile required to take account of both metaffurgical and strategic considerations. Two separate simulation models are developed to achieve this objective. The first model is used to determine the minimum size of stockpile necessary for blending purposes to smooth out variations in concentrate grade between 15 - 60% Cu, with associated 34 6% Fe, respectively, and ensure that the concentrate fed to the furnaces does not faff below 12% Fe, which is considered a minimum for good smeltability.The second simulation model covers a projected three-year operating period and indicates the maximum size of stockpile which is likely to develop during scheduled and unscheduled shutdown periods in the concentrator and smelter.Covered storage volume and conveying facilities for the optimum size of concentrate stockpile can be designed based on the results generated by the simulation models."

Jan 1, 1980