Search Documents

By C. V. Millikan

New developments in air-gas lift practices in the Mid-Continent area since our Pall meeting in Fort Worth have done much to increase the efficiency of installations, and thus bring within economic limit of air-gas lift many wells which could not have been flowed profitably before. After the gas-lift had so thoroughly demonstrated its value in the Seminole field, its use spread to other areas and many installations were made of which the economy could be questioned. In the Seminole area, when production began to decline it was necessary either to increase the efficiency of the air or gas-lift or to put the wells on the pump, and pumping was not a process of lifting oil to which any operator looked forward with confidence. These conditions have resulted in the development of many practices which increase the efficiency and permit wells to be flowed with air or gas which earlier could not have been flowed economically, and wells which have been flowing to continue to a lower rate of production. The practices which have come into more common usage in the Mid-Continent area recently are mostly revivals of and improvements on practices which have been known in air-lift work for several years. Many arc peculiar to the individual well on which they are used. Intermittent Flowing Some interesting results are being obtained in Seminole and other districts by intermittent injection of gas. Gas is introduced during per-iods iods of 3 to 5 min. at a rate considerably over that necessary to acquire the production at a steady rate of injection, and is then cut off for a period of 3 to 15 min. Two to five wells are run from the same group of conlpressors. The total volume of gas required is sometimes reduced as much as one-third of that required when it is introduced at a constant rate, without changing the amount of oil production. The maximum pressure required is usually higher, but the average equal to or lower than that required for constant rate of flow. The effect on the wells is usually an irregular rate of flowing which may cause inconvenience where recycling is practiced. It would seem that this increase in efficiency is due to less slippage when the gas is introduced intermittently than when it is intro-

Jan 1, 1928

By A. H. Bell

The general principles of the gas-lift will not be described in this paper. Only specific details that have not been fully discussed in previous papers, or results that do not fully coincide with conditions previously described, will be dealt with. The principal points to be emphasized and for which supporting data are furnished are as follows: 1. Gas-lift installations usually have comparatively high efficiencies as compared with standard pumping equipment, when reduced to a basis of barrels produced per horsepower installed. 2. Advantages of high-pressure plants from the standpoint of operating efficiency and for the application of the gas-lift early in the life of flowing wells. 3. Evidence of increased ultimate yield through conservation of gas by the gas-lift. 4. Possibility of development of new equipment to increase efficiency of the gas-lift. 5. Indications of the advantages of repressuring as a means of stabilizing gas-lift wells and as a means of increasing ultimate yields. TyPes of Installation The gas-lift installations of the more important companies in California have been of the central-plant type wherever field conditions would permit. This has resulted in greater flexibility and lower installation costs per well than could be obtained with individual well units. In general discussions of the gas-lift method of production, the installation costs are frequently referred to as being too high for economical operation. If the field conditions are carefully analyzed and the plant designed with the idea of obtaining high operating efficiencies, the installation cost per well can be lowered sufficiently to compare favorably with individual well-pumping units, when the operating advantages are considered. Much greater production per horsepower can be obtained with the gas-lift than is possible with pumping equipment. Table 1 shows the unit sizes and costs of gas-lift installations of three companies in the Los Angeles basin. The cost of walking beams, rods,

Jan 1, 1928

By Cyril S., Smith

THE phenomenon of air-hardening is well known in connection with special steels. It occurs when the rate of decomposition of austenite to marten- site is so retarded that it takes place on free cooling in air rather than on more rapid cooling in a quenching bath. If an air-hardening steel is quenched sufficiently rapidly it will remain in the soft austenitic state, while if it is cooled very slowly it will again become soft owing to growth of the carbide particles. It depends on a critical adjustment of the decomposition velocity and diffusion rate, and such alloys are rather rare, especially in the non-ferrous field. In carrying out some experiments on some copper- rich copper-cobalt alloys, the author found that these possess very marked air-hardening properties. The alloys are covered by a patent issued to M. G. Corson (1,723,022-1919), which states that an alloy containing between 2 and 5 per cent cobalt is hardened by simple quenching from above 850° C.

Jan 1, 1930

By James W. Lower

IN developing the orebody on lower levels of the Star mine at Burke, Idaho, Hecla Mining Co. is faced with a serious problem in driving raises. Levels are at 200-ft intervals. As a raise is being driven between levels, at points about 70 and 130 ft from the sill, heavy pressure arches develop and the raise becomes extremely hazardous. Eventually, following a blast, caving occurs, making it impossible to recover the raise. In February 1957 it was decided to attempt sinking a small winze on the vein from the 5500 to the 5700 level. This shaft (winze-raise No. 2) was to be used as a raise prior to stoping. It was assumed, and correctly, that the heavy ground pressure could be controlled by timbering close to the bottom after each advance.

Jan 7, 1958

By O. B. Horne, R. O. Morgan, C. E. Anderson

"Air-photo interpretation and photogrammetry are two of the most effective and versatile tools available to the petroleum industry. The techniques have proven successful in providing solutions to many of the problems encountered in the design and construction of oilfield projects.Although most technical personnel are aware that air-photo interpretation and photogrammetry are useful in the selection of routes for roads and pipelines, few realize the true scope of the techniques or the wide variety of areas in which they are applicable.This paper briefly describes the principles involved, and reviews a number of typical applications of particular interest to petroleum companies. Excessive detail is avoided, rather the emphasis is placed upon the wide spectrum of possible applications. It is stressed that on-the-ground examination generally is a necessary adjunct, and that there are certain limitations to the techniques discussed.Properly applied, however, air-photo interpretation and photogrammetry can offer significant advantages in terms of time, flexibility, secrecy and economy."

Jan 1, 1968

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By Fan Shaogang

In this paper, the airbags' structure and technical characteristics and its applications in China are described. Based on the practice of the airbags in mining thin seams, the effects on ground control are discussed. This paper also analyzes the interaction mechanism between the airbag and surrounding rocks.

Jan 1, 1997

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By Duane Skidmore, Francis Otuonye, Calvin J. Konya

Proper stemming not only affects the rock breakage process, but also controls the unwanted side effects of blasting such as airblast, ground vibration, and flyrock. Little research has been conducted on the behavior of borehole stemming material under high pressure loading conditions. The methods of selecting stemming particle size and necessary stemming length were previously determined only by trial and error in the field.

Jan 1, 1982

By L. A. Schutz

Personnel of the Bureau of Mines have conducted investigations in the principal asbestos mines and mills in the United States, to determine the concentration of airborne asbestos fibers in the workplace, and to establish the exposure of workers to such fibers. 'The surveys were conducted using the sampling and evaluation method recommended by the National Institute for Occupational Safety and Health. The method consists of collecting the air-borne sample on filters and, after appropriate sample preparation, counting the fibers utilizing phase contrast microscopy. The results of the investigation show that fiber concentrations are low in the asbestos mines but high in the asbestos mills, ranging well above 5 fibers/ml of air based on a count of fibers greater than 5 urn in length.

Jan 1, 1973

By J H. J Holtzhausen

Never has there been more focus on the health, safety, and well-being of our employees at the workplace. Ever evolving expectations of individuals, companies and clients are shaping regulatory reviews and advancing standards across the world in the drive to zero harm. The technology is advancing at a rapid pace, which is now allowing continuous real-time monitoring of contaminants to take place in the harshest of environments.

Oct 12, 2022

By J. Partyka, J. S. Stachulak

Dust produced during blasting in a copper/nickel based mine was studied and characterized. A stope utilizing the crater blasting technique, or the vertical retreat mining (VRM method), was examined. Two dust monitors were used to measure an airborne dust produced during blasting operations. The data collected in situ was primarily used to formulate the boundary value problem for a generalized equation that describes the transportation process of airborne dust from all places where dust is produced by the VRM mining method. The field data was also used to define the analytical forms for the initial and boundary conditions, to provide a simple and reliable equation for flow of dust in a stope vicinity, and to identify the non-measurable constants. The effects of the amount of blasting material and of the ventilation system in use on dust concentration are also discussed.

Jan 1, 1995

By Steven J. Page, John A. Organiscak

Airborne dust generation is one of the byproducts of coal mining, processing, and handling. The amount of airborne total dust (ATD, respirable size and larger) and airborne respirable dust (ARD) generated is of primary interest for designing the level of engineering controls needed for adequate dust abatement. Laboratory crushing experiments were conducted in a wind tunnel with a roll crusher to identify relationships among crushing parameters, product size, coal rank properties, and airborne dust generation. Through the first series of experiments, the effect of primary and secondary breakage processes on both product size and airborne dust generation was examined. Through a second series of experiments, the effect of coal rank properties on product size and airborne dust generation was studied using a uniform crushing process with secondary breakage. Laboratory results indicate that secondary breakage of a particular coal notably increases the specific amount of ATD generated, while negligibly impacting the specific amount of ARD generated. A strong positive relationship was identified between the specific amounts of ATD and ARD generated during the primary breakage process (with minimal secondary breakage), but a negligible relationship was observed between the same two variables when secondary breakage was introduced into the crushing process. This indicates that most of the ATD and ARD is generated from the primary breakage, while secondary breakage has a more of an influence on generating additional amounts of larger sized ATD. Additional experiments involving the uniform crushing of eight different bituminous coals showed that the coal rank, expressed as the inherent moist fuel ratio (MFR = fixed carbon =(volatile x inherent moisture)), had diverse relationships between the product size created and the amount of airborne dust generated. As bituminous coal rank or MFR increased, the amount of coal product fines < 250 gm increased while the mass percentage of ATD and ARD liberated from these < 250 µm product fines decreased. Air dry loss (ADL) moisture in the coal was found to be inversely related to the dust cloud electrostatic field, influencing dust liberation from the coal product fines. Since the MFR was directly related to the dust cloud electrostatic field, opposite the ADL-electrostatic field relationship, the diverse relationships between the product size created and the amount of dust liberated from the < 250 µm product fines were explained. Finally, 12 to 14 times more ATD was generated as compared to the ARD generated during these experiments. These results should provide a fundamental basis for initial estimation of the airborne dust loading requirements of engineering control methods for coal crushing.

By Hans Lundberg

An electric survey from a &apos;plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the &apos;plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the &apos;plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the &apos;plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the &apos;plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the &apos;plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By N. R. Paterson

"More than a dozen AEM systems are currently being used in the routine exploration for massive sulphides. The systems differ from one another in minor respects, but fall into four main categories: rigid-coupled in-phase/quadrature systems; towed-bird, single-component systems; differential systems; and passive systems.Although field tests are important in demonstrating the performance characteristics of the AEM/airframe assembly (noise-levels, coupling effects, etc.), more meaningful evaluations can be made through physical or computer modelling. The latter approach has been used to compare the response of twelve AEM systems to both vertical and horizontal sheets, simulating a large orebody and a con-ductive overburden respectively. The effects of height changes are also studied.The results demonstrate that each AEM system has its own particular advantages and disadvantages. The relative importance of these is a matter for the geophysicist to judge, on the basis of specific geological and environ-mental information. Data currently available on AEM systems are adequate to permit an objective evaluation of the systems for a particular exploration program."

Jan 1, 1971

By Ronald R. Hartman

I can recall a time 10 or 12 years ago when I spent a pleasant Sunday afternoon driving to Jim Thorpe, Pennsylvania to see a carnotite deposit that had recently been discovered. The announcement of the discovery stated that it was in the Pottsville conglomerate in a road cut along the highway. To my surprise, the highway was lined with cars and every weekend prospector for 100 miles had come to see the ?big uranium deposit of the east?. I literally had to stand in line to make a measurement with the scintillation counter I had with me. The thought at first occurred to me that this is evidence of how thoroughly the surface of the United States must have been prospected, more likely, perhaps it points out quite the opposite. A lot of time and energy was being spent in tracing the footsteps of others and a lot of time was spent looking for the obvious occurrences. The point is, that in the early days a tremendous amount of uranium exploration was carried out but few systematic surveys were made. Thorium anomalies were usually discounted after cursory surface field checks. Conversely, in airborne surveys - anomalies due to elevation changes or thin over- burden on hilltops were often investigated more thoroughly than smaller indications on hillsides and valleys. An adequate supply of uranium was nevertheless found due to the ingenuity and persistence of the geological profession and the public in general. This ?adequate? supply, like so many estimates for raw materials turned out to be far too low.

Jan 1, 1967

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By Rizzi Homestake Mining Co.

Geophysical methods of discovering new mineral deposits have long been routine with both the petroleum and mining industries. Experience has shown that most subsurface structures and mineral deposits can be located, provided that detectable differences in physical properties exist. The main properties exhibited by the more common rocks and formations are: density, magnetism, electricity, electrical conductivity, and radioactivity. This entails five major geophysical methods: gravitational, magnetic, seismic, electrical, and radiation. Applications of radioactivity measurements in geophysical exploration are concerned with location of concentrations of radioactive rocks and materials, such as uranium. The search for uranium ores and minerals has been carried on for more than 50 years, ever since the first atomic breakdown from uranium to radium was discovered. However, the comprehensive search now being made throughout the world for radioactive materials is a direct result of the first atomic explosion and the subsequent development of new and more sensitive portable equipment to detect radiation.

Mar 1, 1956

By R Miller

The enrichment of magnetite to haematite and haematite-goethite leads to a coincident magnetic low and gravity high within the banded iron formation. Palaeochannel deposits of pisolitic limonite can be expected to provide a relative magnetic high and gravity low in a sinuous geometry. Detrital iron deposits of conglomerate, scree or ‘canga’ might have indistinct magnetic response but will usually have a relative gravity high.These signatures provide clear discriminators detectable by a joint gravity and magnetic survey.The combination of airborne gravity gradiometry and magnetometry is particularly powerful in detecting and discriminating targets, as well as mapping lithologies and structure, across a wide variety of iron ore deposit styles. It provides detection capabilities in a platform capable of rapid, complete coverage with minimal access issues. This approach has been used in FALCON™ airborne surveys for iron ore exploration in the Great Lakes, USA; the Middleback Ranges, South Australia; and the Hamersley Basin, Western Australia.The complex magnetic properties of iron formations (particularly remanence, anisotropy and depth of weathering) prevent this approach from being simple. The use of vector residual magnetic intensity (VRMI), calculated from the measured total magnetic intensity (TMI), assists by reducing the complexity due to the different directions of the remanent and induced magnetic fields.Estimations of the density to magnetisation ratio via the pseudo-lithology calculated from the VRMI and gravity gradients provide a useful method of capturing the discriminatory power of joint magnetic and gravity gradient data.

Jul 11, 2011

By John H. Ratcliffe, Hans T. Lundberg

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravimeter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque produced in a wire spring. The instruments employed are sensitive to the slightest movement; they cannot be used on a moving platform unless velocity is kept strictly uniform.

Jan 8, 1959