Search Documents

By Ning Wang, Bing Xie, Hong-Yi Li

"Compared to traditional sodium roasting, calcified roast inhibits chlorine pollution. A vanadium extraction technique based on a calcified roast is especially suitable for vanadium slag with high calcium content. In this report, V205was extracted from vanadium slag by calcified roast followed by acid leaching and hydrolysis precipitation. In optimized conditions, the high silicon low vanadium slag was roasted at 850'C for 2 hours without CaO addition. The roasted materials were leached with 35 % H2SO4 in liquid/solid ratio of 5:1 (mL/g) at 95OC for 4 hours. The extraction of vanadium was as high as 97.66 %. These results are instructive to V2O5 production in industry.IntroductionVanadium slag is produced in converter, sodium salt roasting is the commonly used technique to extract vanadium. In sodium salt roasting, vanadium slag is roasted with sodium salts including sodium chloride and soda as additives, followed by leaching with acidic or basic solution [1]. However, in this process chloride reacts to produce corrosive gases including HC1 andCl2- SO2 and SO3 can also corrode equipment severely and are also an environmental contaminant. The low melting point of sodium salts leads to fusion agglomeration, which blocks vanadium oxidation and thus decreases the extraction rate of vanadium. A large amount of sodium salts consumed as roasting additives increases the production cost. Moreover, sodium salt roasting requires low CaO content in vanadium slag. When the CaO content increases to 1%, V2O5 extraction can amount to 4.7%-9% [2]. For vanadium slag with high CaO content, the sodium salt roasting technique leads to low vanadium extraction rate."

Jan 1, 2012

By M. Wu, A. Kharicha, J. Bohacek, A. Ludwig

"During the horizontal spin casting of rolls, vibrations and mould deformations seems to have a significant effect on the final quality of the product. Sources for vibrations can be found in the poor roundness and a static imbalance of the chill itself. The bending of the mould axis is also considered. Both, vibrations and axis bending, are used as an input for CFD simulations of the flow dynamics of the liquid metal inside the rotating cylinder. The aim is to study the feedback of the free surface behavior in terms of wave propagation and various wave shapes. Introduction The horizontal spin casting process (HSC) is a casting process that has several advantages over the traditional gravity casting processes. Centrifugally cast products have a high degree of metallurgical purity and homogeneous microstructure. A significant gain is observed for the rupture strength, the rupture strain, and the Young modulus. These properties naturally depend on the centrifugal force and thus, the best mechanical properties can be found at the largest distance from axis of rotation. However proper selection of the angular frequency has to be done in order to prevent the so-called ""metal rain"" i.e. metal droplets can fall down from the upper part of the cylinder due to a too weak centrifugal acceleration. In the same time excessive speeds can lead to the appearance of longitudinal cracks caused by the hoop stress in the initially solidified layer. From empirical knowledge other parameters have important influence on the casting products, it includes the pouring temperature, the pouring rate, the mould coating etc. Recently the presence of natural or forced vibrations have been identified as possible additional factors to be taken into account [1-2]."

Jan 1, 2012

By J. M. Tourre

1995 have seen a continuation of a positive trend in the Rare Earth industry The availability of a greater diversity of Raw Material has brought additional flexibility to the Producers permitting better economics China remains the major raw material source; Chinese concentrate producers have increased capacity in 1995 (Baotou, Sichuan, etc) China's role in the Rare Earth industry will continue to evolve; the acquisition of a majority equity position by San Huan/CNNC will have a significant impact on both the Rare Earth and Magnet markets Chinese producers are increasing the quality of their products and realize their true values Chinese market, itself, is also changing as the internal needs for separated rare earth's grow Already already producer of Lamps, Loudspeakers, Magnets, and TV tubes, China is in an unique position where the potential of its internal market might be more promising than the prospects outside China 1995 has also seen the application market become more diverse and complex. There are new applications growing at a very strong pace (such as battery alloy), applications that are now penetrating their target markets with significantly increased growth rates (such as bonded NdFeB), and some applications that became more complex requiring much more sophisticated products (such as catalysis). Rare Earth producers have to spend significant ressources in order to monitor the market trends in order to predict the demand and then adjust their raw material mix. Even though there is a greater diversity of raw material available, there is still some Rare Earth elements that are in excess, while other are just in balance. As a consequence rare earth producers invest heavily in R&D in order to develop new applications for these excess elements.

Jan 1, 1997

By Markus A. Reuter, Antoinette van Schaik

"Product design engineers select from a wide range of materials and combine them into multimaterial product designs. These include various materials (metals and non-metals) which are complexly integrated (e.g. welded, glued, alloyed, layered). The recycling/recovery rate of consumer products are determined by the different materials and alloys used, but also by the particle size and multi-material particle composition after shredding (combination of materials due to design). Eco-design (for recycling) and Design for Recycling (DfR) can only be conducted if the interconnectivity of material/metal in various unliberated materials is accounted for and its effect on material and energy recovery can be linked back to design. This paper will discuss the basic principles of these DfR models and it is shown how these tools (i) are linked Computer Aided Design (CAD) and Life Cycle Assessment (LCA) software, (ii) affect conceptual design specifications of products, (iii) integrate the complex detail of the recycling system and recyclate quality and hence (iv) make recycling an integrated part of the product system. Furthermore, it is shown how these assessment tools and models can be applied for benchmarking of the recyclability and environmental damage created by the recycling of end-oflife consumer goods in order to e.g. (i) provide the (original) equipment manufacturer with knowledge and solutions to support product stewardship and Extended Producer Responsibility; (ii) create awareness of the consequences/benefits of design, products and recycling systems to manufacturer, designer, legislator, recycler etc.; and (iii) assist the consumer in their choice of consumer goods from an end-of-life point of view.IntroductionA first-principles basis is required in order to be able to simulate and predict the recycling/recovery behaviour of products facilitating Design for Recycling (DfR) and Eco- Design. This links recycling technology and the environmental consequences of recycling directly to product design."

Jan 1, 2008

By O. Tiitu

Drying is a unit process that has numerous applications in metallurgical process industry. Kumera Technology Center is a worldwide equipment and process supplier, who has expertise on both direct and indirect drying. In a conventional direct heated dryer, the required energy is obtained from combustion of fossil fuels emitting a considerable amount of off-gases. However, thermal energy can be already available in some metallurgical plants such as modem copper smelters where steam is produced by waste heat boilers of flash smelting furnaces. The total volume of off-gases, and especially the amount of harmful gases, released into atmosphere can be remarkably reduced when using steam as an indirect energy source for drying. Kumera Technology Center has developed a new type of steam dryer for drying of, for example, abrasive copper concentrate with silica sand. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the existing steam dryers and the rotating drum dryers. In the design, special attention has been paid to overcoming the reported problems of excessive wear and clogging of steam tubes and to reducing the required maintenance operations. The Kumera Steam Dryer, having a patented flexible steam tube arrangement inside the rotating shell, has a high effective heating area - drum volume ratio without leading to problems with build-up and clogging. It can also be easily scaled up so that a single dryer can dry all of the feed for a large flash furnace. In this paper, we will present the operational and maintenance experiences from two years operation of the first full-scale Kumera Steam Dryer at Norddeutsche Affinerie Aktiengesellschaft in Hamburg, Germany. We will also provide an overview of the future developments with respect to construction and scale up as a response to market demands.

Jan 1, 2002

By Adam Powell, Soobhankar Pati

"Solid Oxide Membrane (SOM) Electrolysis is a new energy-efficient zero-emissions process for producing high-purity magnesium and high-purity oxygen directly from industrial-grade MgO. SOM Recycling combines SOM electrolysis with electrorefining, continuously and efficiently producing high-purity magnesium from low-purity partially oxidized scrap. In both processes, electrolysis and/or electrorefining take place in the crucible, where raw material is continuously fed into the molten salt electrolyte, producing magnesium vapor at the cathode and oxygen at the inert anode inside the SOM. This paper describes a three-dimensional multi-physics finite-element model of ionic current, fluid flow driven by argon bubbling and thermal buoyancy, and heat and mass transport in the crucible. The model predicts the effects of stirring on the anode boundary layer and its time scale of formation, and the effect of natural convection at the outer wall. MOxST has developed this model as a tool for scale-up design of these closely-related processes.IntroductionSolid Oxide Membrane (SOM) Electrolysis is a variation on the Hall-Héroult process for molten salt electrolysis of oxides which promises to solve many of the problems of its predecessors. Magnesium in particular is both soluble in molten salts and highly reactive, such that it migrates to the anode and reacts with the oxygen or C02 anode product, reducing current efficiency to as low as 10-20%. But a zirconia solid electrolyte between the molten salt and anode blocks this reaction, boosting current efficiency to at least 90%. Separating the anode from the molten salt also opens up anode material selection to liquid metals and SOFC cathode materials such as Lai.xSrxMn03 (LSM) and YCr03. And zirconia's selectivity makes the oxygen by-product very pure."

Jan 1, 2012

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By David Bequette, Ray D. Peterson, Cynthia K. Belt

"With a need to cut production costs in the metals industry, cost savings from energy efficiency improvements are critical. Opportunities can be found by reviewing furnace systems and practices so that the melting and holding processes operate at the highest energy efficiency. Many of the changes can be implemented with a minimum of expense or capital investment. This paper will review several low cost methods to optimize energy efficiency on reverberatory melting or holding furnaces. These five methods (furnace utilization, idle procedures, fire rate, controls, furnace pressure) will be explained and information given to implement these changes. Included are several rules-of-thumb and benchmarks for aluminum reverb furnaces.IntroductionEnergy can be a significant portion of the total manufacturing costs for metals and materials manufacturing involving thermal processing such as heat treating, melting, and high temperature processing. Natural gas prices have dramatically varied over the last few years. While no one can foresee the future, prices are expected to increase from the current low prices. More recently, emphasis is being put on the reduction of greenhouse gases with the potential of additional costs to industry.One of the first steps in an energy management program is to measure the energy usage of the process [1]. The results are typically understood in relation to the mass melted in kWh / mT [BTU / lb]. For the purposes of this paper, furnace energy efficiency is calculated over a month or even a year and thus includes hold times. This efficiency is typically different from the values quoted by furnace manufacturers. Those values are for limited short term tests at highutilization.Once you know the performance for your furnaces, these should be compared to industry benchmarks. For aluminum melt furnaces with cold air burner systems, a benchmark value or goal is 1800-2000 BTU/lb [1160-1290 kWh/mt], though some of the best have reached 1600 BTU/lb [1030 kWh/mt]. Furnaces with regenerative burners can attain 1100-1200 BTU/lb [710- 775 kWh/mt]. There are some designs of multi-chamber furnaces or oxygen furnaces that have improved on these numbers, perhaps as low as 950 BTU/lb [615 kWh/mt]. Typically, as the degree of sophistication and energy efficiency of the furnace increases, so does the cost."

Jan 1, 2010

By T. T. Natarajan, Nagy EI-Kaddah

"Numerical simulation of electromagnetic confinement systems generally requires large CPU time due to the strong coupling between the electromagnetic and the free boundary problems. The present paper examines the accuracy and the computational efficiency of the most common numerical schemes used in modeling such systems. Levitation melting was taken as a test case. In this study, a comparison was made between the finite element and surface integral methods for electromagnetic field calculations. The computational efficiency of Lagrange and the modified Hestenes methods for solving the free boundary problem were investigated. The convergence of the Lagrange method was found to be much faster than the modified Hestenes method. It was also found that finite element method not only gives accurate solutions, but faster convergence to the final equilibrium shape than the surface integral method. The applications and the limitations of these techniques in modeling electromagnetic confinement systems will be discussed.IntroductionIn recent years there has been a growing interest in the use of electromagnetic forces for confinement of molten metals as a means to eliminate molten metal contamination during melting and to improve surface quality of cast products. Continuous casting of metal without contact of a mold is now a reality, and is being commercially applied for casting of aluminum slabs /1/, and copper rods /2/. New applications of electromagnetic confinement in melting and casting include containerless melting (Magnetic Suspension Melting) /3/, edge containment in twin roll casting, and meniscus shape control in continuous casting of steel /4/.Modeling of confinement systems involves the determination of the electromagnetic field and the equilibrium shape. These two problems are strongly coupled due to the dependence of the field on the shape of the melt. While significant advances have been made in computational electromagnetics /5/, the application of developed computational techniques to electromagnetic confinement problems is not a simple task. The principal difficulty in using these methods is that the solution domain is not known a priori. due to coupling between the electromagnetic field and the free boundary problems. These two problems have to be solved simultaneously, leading to an iterative solution procedure. As a result, numerical simulation of electromagnetic confinement systems are computationally intensive with computational time at least an order of magnitude larger than the fixed domain problems."

Jan 1, 1994

By Freddy Syvertsen

"During the past two years the Association of Norwegian Foundries in Norway has been running a project in evaluation of CAD/CAM systems for foundries.In this work we have had a closer look to the various steps from drawings to the finished castings. On this background we have made a specification of the special needs in the foundry process. The main content of this paper is a presentation of this specification.Some CAD/CAM sytems have been compared with the specification and a summary of the result is presented.In the project we have also had a closer look at some systems where we actually have tried the user interface and some of the possibilities in the systems. In this way we have gained a more detailed knowledge of the systems and we have also got some experience in NC-machining from the systems.IntroductionThe development of CAD/CAM systems has taken place with almost no interaction with the foundry business. This becomes clear when you are having a closer look at the systems. Most of them have not the possibility to describe the complex sculptured surfaces that is often found on castings. The people developing the software, have paid little or no attention to the problems arising when a geometry is going to be transformed for the casting process. Among the problems are the decision of where to place the parting line and to adjust the draft angle. These problems must be solved properly to be able to withdraw the model from the sandmould. In die casting the problems must be solved to be able to get the casting out of the die.In Norway some companies have been developing CAD/CAM systems for several years, with limited interest in foundry problems till 1983. To present the special foundry problems to them a specification of the needs was made that year. Another reason for making this specification, was to compare it with the CAD/CAM systems on the market (1).Design of castingsGeometry transferThe foundries in Norway are small units with almost no design of their own casting products. They are subcontractors receiving paper drawings and limited informations about the product from the mechanical industry both in Norway and in other European countries. This is going to change, and in the future the geometry will be transferred by magnetic tape or by a network of computers."

Jan 1, 1986

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By Bing Hu, Zhu-Cheng Huang, Guang-Bin Xia, Hu Peng, Hua Wang

"The temperature rising characteristics and reaction of the reduction of iron oxide pellets with anthracite fines were studied using a MW-L0316V microwave oven and Leica-DM-RXP polarizing microscope. The results show that iron oxide pellets and anthracite fines have good microwave absorbing properties, and high temperature and reducing atmosphere in a relatively short time for reduction of iron oxide pellets can be achieved. The reduction reaction, which follows the unreacted core model, is rapid and the metallization increases from 13.41% to 56.57% as the reduction end point temperature increases from 850oC to 950oC. The iron is formed, fine grain crystals of iron are transferred and the contraction of metal phase occurs firstly at the surface of pellets, which hinders the reduction reaction at the center of pellets. The rate of reduction reaction increases slowly as the reduction end point temperature increases from 950oC to 1050oC.IntroductionIron ore direct reduction can be divided into gas-based reduction and coal-based reduction. Owing to the effect of the resource and the related economic benefits [1, 2, 3, and 4], the development of gas-based direct reduction technology is restricted, but the development of coal-based direct reduction supported by the relevant industrial policy has very good prospects for application.As a source of clean energy, in China microwaves have been applied in many fields [5, 6, and 7]. Chen Jin studied the reduction of carbon pellets under microwaves, and has made some progress on reduction kinetics and reaction mechanisms. Other countries also have related research in this field [8 - 15], for example, Kotaro Ishizaki and Kazuhiro Nagata have done research on the reduction reaction of carbon magnetite heated by microwaves. The research shows that Fe3O4 is deoxidized to FeO at about 800oC, and FeO is deoxidized to Fe at 1000oC-1025oC. Due to the very good heat absorbing properties of iron oxide pellets and anthracite fines, the selective and rapid heating of microwaves can rapidly raise the temperature of pellets and anthracite, and the iron oxide pellets can be rapidly reduced. In order to provide enough theoretical basis for direct reduction by microwave heating, this paper studies the temperature rising characteristics, behavior of the reduction reaction and the changes of the iron oxide pellets and anthracite in the microwave field."

Jan 1, 2011

By Y. Huang, P. B. Prangnell

"An Al-0.1Mg alloy was firstly deformed at room temperature by ECAE to a true strain of 10, where a steady state deformation was established and further processing had little effect on grain refinement. The ECAE samples, with an average grain size of ~0.55µm, were then compressed in a channel die at 77K- 473K to various reductions. Microstructures were characterized by electron backscatter imaging and EBSD in a FEGSEM. Grain refinement to the ECAE submicron structure occurred during deformation at cryogenic temperatures of 77 – 213K, whereas coarsening took place during deformation at elevated temperatures. A steady state deformation was observed at all temperatures where a constant grain structure was developed and maintained upon further straining due to dynamic recovery. The mechanisms of dynamic recovery during steady state deformation at cryogenic temperatures are discussed.IntroductionSevere deformation processing (SDP) has been successfully used to produce submicron grain structures, and in some cases nano-scale crystallite sizes, in a wide range of alloys. However, the rate of grain refinement becomes increasingly inefficient at high strains as a steady state grain structure is approached [1-3]. Steady-state grain sizes have also been reported in other ultra-high strain deformation processes, like cryogenic ball-milling [4]. There is thus a minimum grain size achievable in a material by a given SPD process under constant deformation conditions.It is well documented that a steady state subgrain size is observed in warm deformation of metals due to dynamic recovery (e.g. [5]). In severely deformed alloys a constant grain size at ultra-high strains has similarly been attributed to dynamic recovery [1-3]. Mechanisms have been proposed, for rapid deformation induced grain growth including stress driven boundary migration and breakaway from solute pinning [2]. However, as pointed out by Humphreys et al. [2] the restoration processes are currently poorly understood, particularly at low temperatures, where the boundary migration rates required to maintain a constant grain size are orders of magnitude higher than can be satisfactory explained from diffusion controlled migration. Similar to the subgrain size, the steady state grain size obtained during SDP is generally related to the temperature compensated strain rate [2, 6]. Thermally activated restoration processes are thus expected to be suppressed by lowering the deformation temperature and a smaller steady state grain size can be achieved."

Jan 1, 2012

By E. Ilgar

"Deposition studies were conducted in acid copper electrolyte to determine the influence of chloride ions on cathode morphology. A statistically designed screening test was carried out in the absence and presence of 20 ppm CI- using a three factor, two level factorial design, in an electrolyte containing 36 gl'! Cu2+ and 150 gl-! H2S04, The independent variables evaluated were agitation; current density and temperature and their influence on surface roughness was determined. The copper deposited at current densities where activation was the primary control mechanism appeared similar in morphology whether stirring was used or not. The addition of 20 ppm CI- to the electrolyte gave rougher deposits under the same conditions. In the mixed control regions, considerably rougher, dendritic deposits were obtained when CI- was present. Agitation was effective in reducing the copper surface roughness both in the apparent activation and mixed control regions in the presence ofCI-. The results of this study showed that 20 ppm Cl- polarized the copper deposition at low overpotentials but caused depolarization at higher overpotentials.IntroductionChloride ion is inherently present in copper electrolyte, either as an additive or from other sources such as make up water. The behavior of the chloride ion is well documented in electrorefining operations, but its role in copper winning is less obvious. However in both cases there is evidence that cathode growth and solution chemistry are strongly influenced by its presence. The mechanism and electrochemical action of the Cl"" have been shown to be very complex, therefore a better understanding of its influence on electrocrystallization is essential for improved cathode deposit growth control. It was proposed that Cl"" polarizes the copper deposition reaction at low concentrations due to CuCI formation but depolarization occurs at higher concentrations due to the formation of a soluble CuCI2"" complex [1,2]. Franklin [3] reviewed the mechanism of additives in the electrodeposition process and proposed that the Cl"" complexed with copper, adsorbed on the cathode as an induced anion leading to an increase in the reduction rate. At cathodic overpotentials less than 100 mY, lppm NaCl had a polarizing effect, i.e. an increase in impedance of the charge transfer step. At higher Cl"" concentrations up to 100 ppm, depolarization occurred as evidenced by a decrease in impedance, which was attributed to soluble cuprous complexes [4]."

Jan 1, 1997

By Zhongliang Tian, Yun Cheng, Yexiang Liu, Ming Jia, Yanqing Lai

"A fundamental electrochemical study of Si ions in Na3AlF6-LiF melts and electrolysis using liquid cathodes was conducted. Cyclic voltammograms (CVs) clearly showed the depolarization of silicon deposition on liquid cathode by forming chemical complexes with the liquid solvent metals. Besides, co-deposition of Al and Si is possible when Si ions are insufficient in the molten salt. Based on the electrochemical results, silicon diffusion into liquid cathode is modelled and evolution of Si activity with concentration is deduced by a mathematic approach. Electrochemical study using liquid metals as working electrodes, can be used as an alternative approach for the acquisition of basic data on alloy behavior. Galvanostatic electrolysis showed that liquid cathodes are appropriate to collect the deposited solid silicon and the highest collection efficiency is almost 85%.IntroductionRecent years have witnessed an increasing demand for solar-grade silicon (Si) by the photovoltaic industry [1-4]. The preparation of high-purity metals through electrolysis and electrorefining offer many advantages such as low cost, low-energy consumption, and environment-friendly process, and thus has been widely used worldwide. From the perspective of electrochemistry [5-7], by utilizing the electronegativity difference between the impurities and Si and controlling the relevant process parameters, it is possible in principle to electrodeposit monatomic Si from a Si4+-containing compound melt. Moreover, because the carbon content of the high-purity Si obtained through electrolysis can be effectively controlled and used as a very ideal raw material in the preparation of electronic-grade and solar-grade Si, the preparation of high-purity Si through electrolysis has received widespread attention [8,9]. Monnier et al. [9] used a graphite electrode to obtain high-purity Si (99.9 %-99.99 %) from Si02/Na3AlF6 system through electrolysis; however, because the Si was precipitated in a solid form and showed poor conductivity, the deposition rate was too slow. Olsen et al. [10] obtained high-purity Si films via electrodeposition in K2SiF6/KF-LiF system by selecting electrode materials with high surface quality (such as Ag and graphite). However, in order to ensure the film quality, the deposition current density must be relatively low (10-50 mA/cm2), resulting in a low current efficiency and low deposition rate, which are not conducive to reducing energy consumption and applying to practical use"

Jan 1, 2014

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By K. Morsi, S. K. Kassegne, K. S. Moon, A. Numula

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based manufacturing of macro, micro and possibly nano-scale features and shapes. CATS enables the selective sintering of powders by localizing current activation conditions through an electrically conducting small tip (either in the stationary or moving mode). This paper presents preliminary experimental results on the CATS of reactive mixtures of Ni/Al powder to form nickel aluminide intermetallics. Preliminary investigations on the effect of current on the reaction characteristics are discussed.IntroductionSpark Plasma Sintering (SPS) has been the subject of intense research over the past decade [1,2, 3,4,5,6]. The process boasts remarkable advantages which include ultra fast heating rates (hence by-passing low temperature non-densifying sintering mechanisms), considerably lower sintering temperatures and shorter sintering times than achieved in conventional sintering. The process is however limited to the generation of simple geometries on the macro-scale. Recently three of the authors conducted work on a novel process ""Current-activated tip-based sintering (CATS)"" [7], where electric current is passed through a conducting tip that is placed or allowed to travel over a powder bed/compact to locally sinter powders. lD, 2D and 3D micro-scale sintered shapes can be generated with the possibility of 3D rapid prototyping on the macro/micro or nano-scale. Although CA TS of single phase powders has been conducted, the CATS of reactive powders has not yet been investigated.The Ni-Al phase diagram contains five intermetallic compounds, AhNi, AhNh, AlNi, AhNi5 and NhAl. Out of these intermetallics, NiAl and NhAl have received the vast majority of scientific and industrial interest [8]. NhAl can be formed by reaction synthesis, where nickel and aluminum reactant powders are heated to a reaction ignition temperature at which the reactant powders are converted to the intended intermetallic product. The reaction is exothermic which gives rise to considerable compact self heating, thus instantaneously raising the compact temperature by several hundred degrees which facilitates sintering [8]. Applying and electric current locally would not only provide for a rapid local reactive sintering, but would generate a number of intriguing scientific investigations. For example, of interest would be, how would the reaction propagation and microstructural/phase evolution be affected by the temporal and spatial temperature and current distributions."

Jan 1, 2011

By N. Mizutani, S. Harada, Z. Asaki, T. Tanabe

"The development of lead-free solders is urgent in view of environmental standpoints. In this -work the wettability of tin-bismuth- silver solders on copper was studied. Three kinds of fluxes were used. The wettability of conventional eutectic tin-lead .solder exhibited an excellent level over the other solders of tin-bismuth systems. Poor wettability of the tin-bismuth solders may be caused by the growth or dendritic copper-tin compounds at copper/solder interface, in contrast to the case of tin-lead'· solder. The wettability was improved by the addition· of silver in the solder. In this tin bismuth- silver system, silver was abnormally concentrated at the copper I solder interface even in the initial stage of contact. The wettability of the solder and the thickness of compound formed on the copper have a good correlation; the solder containing 2% silver exhibited the best wettability and the formation rate of copper-tin· compound on the copper was slowest.IntroductionSocial demand to avoid lead use in the industrial fields has been recently promoted· (1) because of the environmental protection of water resources. Especially the lead-bearing solders have been widely used in electronics and automobile products, and it is urgent to replace them with nontoxic materials (2)-(4). Thus the development of lead-free solders becomes an indispensable subject to the new generations and many works (5)(6) have already been carried out on the research and development of new solders. New lead-free solders are expected to have some requirements, for example, moderate melting temperature, proper strength and integrity, and lower prices, as compared with conventional solders. There have been already several alloy systems developed. Among ·these alloy systems, tin-bismuth binary or tin-bismuth-silver ternary alloys have great advantages such as having a wide range of soldering .temperature by controlling con:ipositions, though they have such disadvantages as ""lift-off"" (7)-(9): It is said, on the other hand, that a frequently overlooked property of solders, or one that is typically ignored by the research scientist as an ""issue"" for the manufacturing or product engineer, is wettability (10), although a ·work on the wettability has recently been published (11). In this Work, therefore, the authors selected Sn-Bi-Ag solders and focused mi the effect of Ag-addition to wettability of the solder."

Jan 1, 2000

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Viviane Tavares Moraes

"The development of mobile phone technology has increased the replacement of outdated equipments for more modern models, transforming disposal of such devices into a serious environmental problem. Recycling appears as an attractive alternative to minimize the environmental impact of disposing such large quantities. Recycling can be accomplished by treating the printed circuit boards of used mobile phones by using the same techniques used in ore treatments with hammer mill; magnetic separation, electrostatic separation and grain size range. Before performing the recycling process a PCB characterization was performed to identify the fraction with the higher metals concentration/content. This study demonstrated that the electrostatic separation was not the best metals concentration of PCB aiming the recycling, while the non-magnetic residue had presented a more significant metal concentration. Furthermore, after the magnetic separation was possible to separate the following metals: iron and nickel.IntroductionPortable electronic devices have gained increasing acceptance over the last decades. Mobile phones sales in Brazil, for instance, have reached 104 million in 2007, and 128 million in 2008. It is estimated that, around the world, 100 million mobiles are thrown away every year, either because of loss of functionality or because newer models are launched in the market [1,2, 3]. Printed circuit boards in mobile phones are made of many materials, with approximately 83% in weight being metals and fiber-glass, and the balance being plastics pl. Several metals can be recovered from the electronics waste, such as copper, tin, iron, lead, nickel, titanium, aluminium as well as some precious metals such as gold, silver and palladium [4, 5, 6, 7, 8]. Concurrent with the increasing world demand for copper, there average metal content in ores has been decreasing. Economically interesting copper mines used to have 4% metal content, whereas presently, such content is around 1%, i.e., for every 1 ton of ore extracted, only 10 kg are copper [9, 10]. Approximately 33% of printed circuit boards (PCBs) composition is copper, that is, for every 1 ton of PCBs waste, 330 kg are copper [1]. Research in recycling PCB waste focuses on mechanical, electrometallurgy, pyrometallurgical and hydrometallurgical processes [3, 8]. Collecting and recycling obsoletes electro-electronic equipments is very important these days, in order to, not just preserve the non renewable natural resources but also to keep the environment and the population safe from the pollution caused by the toxic materials and heavy metals present in this kind of waste."

Jan 1, 2011

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013