Search Documents

By F. J. Tavera

The column flotation technology, at first developed for application in mineral dressing, has received special attention in processing of non-mineral dispersions as a result of its low cost, high efficiency and relatively simple operation. This paper presents the results from the operation of a laboratory flotation column for the separation of vegetable oil and soap from aqueous industrial effluents, The flotation system was operated under continuous countercurrent conditions without and with additions of a cationic collector. The experiments show that it is possible to separate about 80% of the organic phase in a rougher flotation stage. These results suggest that the recovery of the organic phase is highly dependant on the dispersion characteristics (i.e. bubble size, gas holdup and bubble surface area flux) and the existing an optimum bubble size from which either smaller or larger, the recovery of the organic decreases.

Jan 1, 2003

By Kang-In Rhee

A series of processes to recover the gold from electronic scrap which contains initially about 200-600 ppm Au have been developed. First, mechanical beneficiation including shredding, crushing and screening was employed. Results showed that 99 percent of gold component leaves in the fraction of under 1 mm of crushed scrap and its concentration was enriched to about 800 ppm without incineration. The scrap was leached in 50% aqua regia solution and gold was dissolved completely at 60°C within 2 hours. Other valuable metals such as silver, copper, nickel and iron were also dissolved. This resulting solution was boiled to remove nitrous compounds in the leachate. Finally, a newly designed electrolyzer was tested to recover the gold metal. More than 99% of gold and silver were recovered within an hour in electrowinning process.

Jan 1, 1995

By H. Kaffash

Ferromanganese is a ferroalloy with high manganese content which finds many uses for example as deoxidizer in steelmaking industry. However, there is very little data on the dissolution rate of carbonaceous materials in Mn containing metals. In this paper, the kinetic analysis of carburization reactions is investigated for Mn–Fe alloys. Dissolution rate of graphite in pure iron and four different alloys with 10 wt%, 40 wt%, 60 wt% and 85 wt% manganese at 1823 K was studied. Results showed that the dissolution rate of carbon from graphite increased with increasing time for all alloys. The dissolution rate constant increased with the increasing manganese content from 6.5 × 10−3 cm/s for 0%Mn to 23.6 × 10−3 cm/s for 85%Mn.

By Ricardo Melamed

Metallic mercury has been extensively used for gold recovery. Although the solubility and mobility of metallic mercury is low, this metal can undergo many transformations, leading to mercury contamination in humans. The complexity of Hg chemistry in the environment reflects its different possible oxidation states and species, with different physical-chemical properties. The interaction of Hg in the terrestrial system, as well as in the aquatic environment, is important to understand the mercury cycle. This paper reports data on the adsorption of Hg onto an Oxisol soil. Results show that the interaction of Hg(II) at the soil-solution interface depends strongly on ligand concentration in solution, which can affect Hg mobility. The presence of the chloride anion in solution increases the mobility of Hg(II) through the soil, due to a relative lower affmity of mercury chloride at the oxide surface. In the absence of chloride, Hg(II) form strong complexes with the surface, and its adsorption behaviour is similar to the adsorption of other hydrolizable cations.

Jan 1, 1996

By Guangshi Li, Xionggang Lu, Xueliang Xie, Xingli Zou, Yuyang Bian, Hongwei Cheng, Kai Zheng, Changyuan Lu

The corrosion resistance and corroded microstructure of MgO-C refractory in molten slag are investigated by immersion test in muffle furnace at 1600 °C . The microstructure and chemical compositions of the specimens after erosion experiment are characterized by scanning electron microscope (SEM) and energy dispersive X-ray (EDX). The results confirm that the oxidation of graphite is the most important degradation mode of MgO-C refractory. The structure of the refractory material is damaged due to the decrease of graphite, as a result, the periclase substrate reacts with the molten slag directly. The corrosion process is controlled by the dissolution of the refractory materials into slag, low melting point oxides are therefore generated which lead to the damage of MgO-C refractory finally.

Jan 1, 2015

By Luísa Maria Abrantes

Environmental control is becoming more and more stringent. As conventional processes for zinc production are pollutant routes, alternative methods have become an important subject of research. In this regard, the leaching processes have aroused a considerable interest, namely the electrochemically induced approach. The behaviour of zinc concentrate ore in the leaching processesses is influenced by several parameters. Chloride concentration and leaching solution pH, time and temperature of reaction were studied in order to evaluate their influence on the zinc recovery. The efficiency of the leaching process for zinc extraction is performed by factorial design. The experiments were carried out by 23 and 22 factorial designs of the factors. Results show that all factors, except for the time of reaction have a significant influence on the optimisation process, within each experimental region.

Jan 1, 2001

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By P. G. McCormick

The refining of rare earth metals by the direct solid state reduction of their respective chlorides during mechanical alloying has been studied. Erbium and gadolinium were synthesised by milling their respective chlorides with calcium. The mechanical alloying of SmC13 with calcium resulted in partial reduction of SmC12. Examination of the milled powders using X- ray diffraction and analytical electron microscopy has enabled characterisation of product structure and morphology. The synthesis of Fe17Nd2 by the mechanical alloying of NdC13 and Fe with calcium has also been studied. The Fe17Nd2 phase forms during heat treatment of the mechanically alloyed powder.

Jan 1, 1992

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By D. I. Davidov, D. A. Shishkin, M. B. Rigmant, E. P. Romanov, N. N. Stepanova, N. V. Kazantseva

The Co-19 at.%Al-6 at.%W alloy was prepared by two methods of casting. We used arc melting under an argon atmosphere with casting into a copper water-cooled casting mold and induction melting furnace with casting into a ceramic Al2O3 mold. According to the X-ray and SEM analyses, phase compositions depend on the cooling rate of the ingot after melting. After arc melting, the cast alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co3W (DO19) type. After the induction melting, the alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co7W6 () type. All phases in the investigated ternary alloy at the room temperature are ferromagnetic. Curie temperatures of all obtained phases were defined. It is shown that the magnetic properties of the studied alloy are typical for soft magnetic materials.

Jan 1, 2015

By Roberto Parra

The selective reduction smelting of Cu2O in Cu2O-FeOx-SiO2 melts has been studied at laboratory level, using as a feed a dead roasted calcine from a copper concentrate. The purpose of the study was to evaluate the kinetic and mechanisms of the indirect reduction with CO and the direct reduction with graphite from 1260°C to 1350°C. The reduction rate by CO was found to be 10-2 to 10-1 mole Cu2O m-2s-1. The graphite reduction macrokinetics for FeO and. Fe2O3 containing melts, was found to be a first order reaction with respect to the Cu2O concentration, with a kinetic constant of 104 to 10-3 s-1. The reduction rate was not sensitive to temperature nor to stirring, in the range studied. The measured reduction rate is almost one order of magnitude larger than the observed rate for the direct reduction of FeO.

Jan 1, 1999

By Marisa Di Sabatino, Michael Phan Knudson, Mari Juel, Eivind Øvrelid

"A p-type Czochralski silicon ingot doped with boron was characterized for resistivity, minority carrier lifetime, interstitial oxygen, and metallic impurities. Analyses show a peak in resistivity and a dip in lifetime both occur 5 cm from the top of the ingot crown. This peak in resistivity deviates from the expected trend based on Scheil's equation for boron distribution. High concentration of interstitial oxygen in this area suggests that other oxygen-related defects, such as thermal donors and precipitates, may also be present here, and the observed peak in resistivity and dip in lifetime could be attributed to such defects. The low lifetime of 15-30 µs at minority carrier density of 7.5 x 1014 cm-3 is likely due to copper contamination.IntroductionSolar energy resources vastly exceed all other alternative energy resources, ensuring that solar power must play a crucial role in the evolving energy market. The economic viability of solar power in competition with other energy resources depends upon finding efficient, cost-effective, reliable, and controlled methods for solar cell production. In this regard, minimizing waste (such as material with unsuitable electrical properties that hinder solar cell performance) is a vital component of making solar cell manufacturing cost-effective. Impurities affect electrical properties of solar cell silicon in different ways (i.e. [1, 2, 3, 4, 5, 6]). In this work we focus on the role of oxygen and metallic impurities. Understanding oxygen impurities in silicon is critical to solar cell development because oxygen has been attributed with influencing critical electrical properties including resistivity and minority carrier lifetime and thereby potentially hindering solar cell performance or rendering material unsuitable for solar cells.[1, 2] Furthermore, oxygen is a common impurity in the standard type of solar cell silicon, Czochralski (CZ) silicon, due to diffusion of oxygen from the silica crucible into the melt during crystallization. [7] This study investigates the effects oxygen impurities have on the electrical properties of p-type CZ silicon."

Jan 1, 2013

By Wenjun Duan, Kun Wang, Qingbo Yu, Qin Qin

"A novel oxygen production technology noted chemical looping air separation (CLAS) was introduced and properties of Cu-based oxygen carriers used were investigated. The oxygen carriers were prepared by mechanical mixing. Al2O3, Fe2O3, ZrO2, TiO2 and SiO2 were used as binders during the preparation. XRD patterns show that spine! oxides are formed using Al2O3 and Fe2O3 as binders. Phases of CuO and binders keep stable using ZrO2, TiO2 and SiO2 as binders. BET values of oxygen carriers increase in the order of ZrO2>TiO2>SiO2>Fe2O3>Al2O3. The effects of temperatures, binders, particle sizes and flow rates on reduction/oxidation reaction rates were studied in TG experiments. The reduction reaction rate increases in the order of ZrO2>TiO2>SiO2. The effect of binders on the reactivity of oxidation is not obvious. The reduction and oxidation reaction rates both have the tendencies of increasing with the temperature increasing and with gas flow decreasing. However, the effects of gas flow and particle size are little.IntroductionChemical looping air separation (CLAS) is a novel oxygen production technology. The oxygen carriers used in CLAS release oxygen in reduction reactor and regenerate in the oxidation reactor. Selecting suitable oxygen carriers is the key for CLAS. Oxides of CuO, Mn2O3, Co3O4, Pb3O4, CrO2, SrO2, PdO2 and CeO2 have the property of releasing oxygen at suitable temperature and oxygen partial pressure [1]. Among these oxides, CuO, Mn2O3, Co3O4 are the most common compositions used to prepared oxygen carriers for chemical looping combustion (CLC) or chemical looping with oxygen uncoupling (CLOU) [2-5]. Moreover, thermodynamic calculations and preliminary experiments were carried out on oxides of Cu (CuO/Cu2O), Mn (Mn2O3/Mn3O4) and Co (Co3OJCoO) by Moghtaderi to ascertain their feasibility for CLAS process [6]. CuO has the highest oxygen transport capacity (0.1 g 02/g CuO compared to 0.03 g 02/g Mn2O3 and 0.06 g 02/g Co3O4). However, agglomeration is the biggest issue for copper oxides used at high temperature because of its low melting point (l 450°C for CuO, 1235°C for Cu2O and 1075°C for the mixture of CuO and Cu2O) [7]. In order to improve the capability of anti-sintering and stability ofCuO, binders (ZrO2, MgAl2O4, TiO2, SiO2, Fe2O3, Al2O3, cement) are added during the preparation of Cu-based oxygen carriers [8]. In this paper, the Cu-based oxygen carriers were prepared by mechanical mixing method. TiO2, Al2O3, Fe2O3, ZrO2 and SiO2 were selected as binder. XRD, BET and SEM were used to analyze the phase, surface area and surface morphology of oxygen carrier prepared. The reactivity of oxygen reduction and oxidation of oxygen carriers prepared were investigated in STA409PC thermal analyzer."

Jan 1, 2014

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Masatoshi Ogasawara

Saganoseki smelter & refinery operated two flash smelting furnaces, producing a combined 330,000 metric tons per year (hereinafter mtpy) of copper. In 1996, however, it successfully shifted to a single furnace operation while maintaining production at the same level. Since then, the production capacity has been further increased to the present 470,000 mtpy by technological improvements. Also, in order to reduce the converter load which represents a bottleneck in efforts to increase production, the matte grade was gradually increased and currently runs at 65 to 66% attaining the low copper content in the slag (hereinafter slag loss) of 0.7 to 0.8%. This paper introduces some improvements, recent operation results and thermodynamic analyses.

Jan 1, 2003

By Chao Li, Hongxu Li, Yang. Xie, Meng Wang, Xiangxin Hao

"With the development and utilization of resources of gold, high quality gold mine resources gradually exhausted, and refractory gold ore has become the main raw material for gold smelting, while the smelting pollutants impacting on the ecological environment is growing, in recent years there have appeared several methods of green extraction of gold such as bio-oxidation. In this paper, the life cycle assessment models about three different gold extraction technologies have been put forward. Material consumption, energy consumption and emissions during each gold production process are analyzed by using GaBi 6 software, and the environmental impact of each process is also evaluated by means of CML2001 methodology. Calculation and analysis results show that the energy consumption and material consumption are the main factors causing the environmental load; and the environmental impacts of the production process mainly attribute to the category of greenhouse effect, resources consumption and environmental acidification. Based on the evaluation, some optimization tips are proposed.IntroductionOver the past decades, as the industry policy environment continues to improve as well as gold exploration and mining smelting capacity continues increasing, gold production shows a prospecting tendency. With the wide use of gold, the demand for gold is growing, while easy smelting gold mine resources become exhausted and refractory gold ore has become the main raw material for gold smelting. In addition, pollutants impact on the ecological environment is also growing year after year.LCA (Life Cycle Assessment) makes evaluation of product “from cradle to grave” as its whole process, up to finding the sources of environmental impacts and solutions, to comprehensively account the use of resources and lower emissions. In the industrial field, life cycle can compare different technologies from different aspects of resource use, energy consumption and environmental emissions [1]. In recent years, using LCA to evaluate metallurgical industry process also has more development. The paper mainly uses LCA and scenario analysis for the gold metallurgical process by GaBi 6, to investigate the environmental impact of three different technologies of gold extraction metallurgical process. The established three evaluation models include the hydrometallurgical, pyro-metallurgical processes and bio-oxidation pretreatment methods respectively. Several environmental indexes would be selected to evaluate the environmental impact in order to find which process has smallest environmental load and some suggestion of reasonable way gold resource utilization."

Jan 1, 2014

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"A novel approach for foam glass preparation, namely vacuum-aided powder sintering technique, was preliminarily investigated in the present communication. The key point of which was to prepare foam glass at a negative pressure. Compared to normal powder sintering process, the new approach could benefit the foaming process by shorting the holding time, reducing the amount of foaming agent and especially decreasing relative density of the product. Optimum conditions were 750 °C, 1000 Pa, 5 min and 1 wt.% foaming agent, respectively.IntroductionFoam glass represents a highly valuable solution for thermal and acoustic insulation, since it possesses a generally higher mechanical, chemical and thermal stability than other foams'1'. The first industrial processing for foam glass production, the direct introduction of gases (""blowing"") into the special molten glass, can be dated back to the end of 1930s'2'. At present, almost all foam glasses is prepared by powder sintering technique instead of blowing,3 since it reduces the temperature by several hundred degrees. Moreover, as fine glass powders or similar powders can be used to substitute corresponding glasses by this technique, considerable attention has been focused on the production of foam glass by considering fully recycled glasses, coal fly ash, or other solid wastes as raw materials,4 especially CRT glasses'3' 5', on the point of environmental protection.In a previous report'6', when discussing the lead removal and recovery from CRT funnel glass by a pyrovacuum process, we found that foam glass could be prepared at a negative pressure. Therefore, in this communication, the similarities and differences between the powder sintering process for foam glass at normal and negative pressure was preliminarily discussed."

Jan 1, 2011

By Honggang Zhong, Tan Yi, Qijie Zhai, Zhao Dan, Xinping Mao, Huigai Li

"The influence of superheat degree on the distribution and volume content of inclusions were studied in 65Mn thin slab produced by compact strip production(CSP) in Zhujiang Steel in China, The results showed that the diameters of inclusions are mainly less than 5µm. Most of the inclusions gathered at the 1/4 thickness direction for the thin slab of 27? superheat degree, compared with the center position for that of 37?. There are more inclusions larger than 50µm in the low superheat samples, which is caused by the short floating time. In addition, the inclusions were observed and analyzed by metallurgical microscope, SEM and EDS in order to ensure their composition, type and further find their source. It was find that the types of these inclusions mainly are Al2O3, SiO2,CaO and their composites, a few of them are TiN and MnS.IntroductionIt is well known that inclusions have a great impact on the strength, plasticity, fracture toughness, cutting performance, fatigue property and corrosion resistance of steels. Especially, with the demand for thinner slab, the cleanness is increasingly becoming more significant as a quality criterion[1]. High manganese and carbon steels not only demonstrate high strength but also proper plasticity. There are many problems unsolved for 65Mn steel as a result of the low solidification rate, bad thermal strength, crack sensitivity and low casting temperature[2,3].The superheat of the molten steel has a great impact on the erosion of refractory lining, molten steel fluidity and non-metallic inclusion behavior[4]. The serious erosion situation of ladle lining, nozzle and casting tundish will give rise to more inclusions at a high superheat. Meantime higher superheat will make second dendrite arm spacing coursing and element segregation which lead to inclusion, bubble formation and shrinkage cavity. On the contrary, it is hard for non-metallic inclusions to float up with a low superheat value. Inclusions of 65Mn steel, which produced in different superheat condition by CSP, were studied for the sake of higher slab properties including statistics and EDS analysis."

Jan 1, 2012