Search Documents

By Karl Jr. Zipf

The famous Homestake gold mine in Lead, SD. closed recently alter 125 years of operation. However, the mine may receive a new lease on life as a National Underground Science Laboratory (NUSL) supported by the National Science Foundation (NSF) and dedicated to high-energy physics experiments involving neutrinos. These experiments require the construction of many large underground chambers tells of meters wide at depths of over 21 18 m. Construction of such large openings at such extreme depths has few precedents m civil-engineering-type construction. The Spokane Research Laboratory has a long history of ground control research at the Homestake Mine and has supported NSF and the physics community in their efforts to develop a NUSL at I Homestake or other suitable location. This paper will summarize underground science and describe proposed underground science laboratories ill the United States, in particular tile proposed NUSL at Homestake. Next, the paper describes an empirical design approach using the Q system of rock mass classification for these large Openings. .M initial site investigation that produced three good case histories is described. The actual support system used at the three sites agrees well with support recommendations from current support design charts, giving credibility to estimates of the classification parameters and Q. Feasibility of, and support requirements for, 25-, 50-, and 100-m spans arc estimated in the anticipated rock mass. This analysis indicates that 25- and 50-m spans are probably feasible, but a stable 100-nn span may be unachievable. The empirical predictions are then compared to detailed numerical analyses. The paper concludes with preliminary support recommendations and necessary site investigations needed to make a proposed NUSL a successful reality. These studies have been important input to NSF for their decisions on the technical feasibility of developing the proposed NUSL. If NUSL is developed, it could enable scientific experiments in areas beyond high-energy physics. 'the laboratory could also enable research in rock mechanics. ground water hydrology. mining engineering, nine safety and health, and ground control.

Jan 1, 2002

By Andre Cezar Zingano

"The objective of this paper is to estimate the coal seam strength and the pillar safety factor for low coal seams using back analysis and rock mass characterization. The coal seam strength is very important to estimate both pillar capacity and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the boreholes cores; and (ii) by back analysis from pillars successes and failures, or some in-situ tests. For low coal seams (1.2 m, or 47 in.), the confinement of the center of the pillar is very important to defining global pillar strength because the low seam height increases the confinement of the pillar core, even in small pillars. We used in this case study one underground coal mine in the Parana State where the coal seam thickness is 0.8m the pillar height is 1.3m, the entry width is 5m and seam depth is 130m. A panel test was prepared to study the pillar behavior for use of the retreat mining method. The designed pillar size was 6x5m and 1.3m high with a predicted safety factor of 1.0 based on the Hoek and Brown failure criterion is 5.3 MPa. Once no pillar failure was observed, the pillar safety factor was assumed at 1.0 and the coal seam strength was backcalculated. The back analysis estimated the coal seam strength to be 6.2MPa. The confinement of the pillar center directly affects the coal pillar strength, and also the coal seam strength estimated by back calculation.IntroductionThe coal seam strength is very important to estimating pillar strength and mine section design. There are two approaches to estimating coal seam strength: (i) by geomechanics characterization of the coal seam using borehole cores; and (ii) by back analysis from pillar successes and failures, or some in-situ tests like panel test or ultimate pillar capacity (Salamon and Munro, 1967; Maleki, 1981; Peng and Dutta, 1992). For the first approach, lab tests (mainly triaxial tests) and borehole geomechanics descriptions (quality and quantity of the discontinuities) determine the coal seam strength by the Hoek and Brown failure criterion (Hoek and Brown, 1997). For the second approach, a panel test to study the pillar behavior can be built to define coal seam strength by back calculation. The safety factor for the pillars in the test is 1.0, based on the estimated coal strength from the geomechanics characterization. In this case, the probability of failure is 50%. If some pillar failure occurred, and the real pillar size was measured, the back analysis could be applied to define pillar strength and the coal seam strength."

Jan 1, 2015

By Zhang Hongzhen

The fast convergence of boundary is a major problem of probability integral method, especially for the prediction of mining under thick alluvium, abandoned mine goaf, etc. To solve this problem and improve the accuracy of probability integral method, a modified model is constructed for surface movement and deformation based on theoretical analysis. In which, three weighted values i.e. 1, -1/t1, 1/t2 are set for the mining movement and deformation of three different major influence radius i.e. r1, R1, R2, respectively, then the parameters are selected as following: (1) Parameters are inversed based on the observation data, in which the subsidence factor q, deviation of inflection point s, displacement factor b are considered as generic parameters, the tangent of major influence angle tanß is modified as tanß2, that is the major influence radius r is modified as r2. (2) Inversion parameters of tangent of major influenceangle tanß or major influence radius r, based on the observation station edge data which beyond major influenc eradius distance from work-face mining boundary. The inversed tanß and r will be used as tangent of major influence angle tanß1 and major influence radius r1, respectively. (3) Other relevant parameters i.e. t1, t2, R1, R2, are calculated with the algorithm of this paper. A comparison experiment between the traditional and modified models has been conducted using the observation data from a observation station, the results show that in its central area, 58.6 percent of observation points accuracy is improved and 36.6 percent is decreased, while in its edge area, 61.5 percent is improved and 15.4 percent is decreased, totally, 68.6 percent is improved and 30 percent is decreased. Therefore, we can draw the conclusion that our modified model can improve the prediction predication accuracy, in particular, the boundary region.

Jan 1, 2014

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By Weijia Guo

With the exploitation of coal resources, a large area of land had been affected by surface subsidence, causing conflicts between man and land to become more conspicuous by the day, affecting the life of general public, and constraining further development of the land. This paper predicts the subsidence areas according to the 10-year mining plan of the Jibei mining district as an example. A plan of environmental management was developed based on sciences and practical economics.

Jan 1, 2006

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Liang Dong, Jinxuan Liu, Biao Qiu, Jing Chai

"The Cenozoic unconsolidated strata in the east area of China are composed of clay, sandy clay, fine sand, hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged in various degrees since 1987. The main reason for this disaster is the vertical additional stress on shaft caused by the subsidence of the thick unconsolidated strata. In order to monitor the subsidence deformation of the unconsolidated strata, a sensing network system with multiplexed Fiber Bragg Grating (FBG) for monitoring settlement deformation of the unconsolidated strata in deep borehole is proposed. The field monitoring results show that, soil layers settle or expand with decrease or increase in ground water levels. The thick hardpan generates the main compressive deformation. This FBG strain monitoring method can take place of traditional ground water measuring method. This system is stable and reliable, and the monitoring results can show the subsidence deformation of different layers, which has significance for the predictive maintenance of the shafts.INTRODUCTIONSince 1980s, a specific geologic hazard has occurred frequently on the coal mine shafts in eastern China: non-mining-induced shaft deformation, involving up to 100 shafts located in Jiangsu, Shandong, Anhui and Herran province, distributed in Xuzhou, Datun, Huainan, Huaibei, Yanzhou and Yongxia coal fields. This kind of geologic hazard can lead to shaft wall deformation, water infiltration, cage stuck, water-sand burst or shutting down of coal mines, which seriously risks the coal mines. Zhangshuanglou coal mine, Haizi coal mine and Linhuan coal mine shut down for 2-8 months due to this hazard (Chen, 1997; Cui, 1998). The main reason for this geologic hazard is the subsidence of the super thick unconsolidated strata (Liu et al., 2007; Xu et al., 2006).An innovative structure health ·monitoring and damage estimation method has been developed in recent years, i.e., optical fiber smart material and structure (Nobuo, 2002; Wang et al., 2000). A Fiber Bragg grating (FBG) sensor is a device that can transfer the change of the measured strain or temperature to the change of Bragg wavelength. One of the most important applications of FBG sensors is to monitor the internal stress and strain distribution of material and structure (Philipp et al., 2000; Ansari et al., 1998). Compared to traditional electrical sensors, FBG sensors have many advantages; they are adaptable to harsh environments, abrasion resistant, immune to electrical magnetism (EM) interference, safe and reliable. They also offer integrated sensing and transmission on a single fiber, have simple structure and are convenient to use, which satisfies the requirements of long distance, distributional and long term use in monitoring mining and geotechnical engineering structure. Due to such advantages, the FBG sensor has already been applied in petroleum engineering (Kersey, 2000), rock mechanics testing (Cornelia et al., 2003; Yang et al., 2007; Wei et al., 2008), physical simulation experiments (Chai et al., 2007; Chai et al., 2006; Zhu et al., 2008; Li et al., 2008; Chang et al., 2008), strain sensor (Li et al., 2007; Chai et al., 2008) and construction structure damage diagnosis (Dong et al., 2004; Kerrouche et al., 2008; Whitten et al., 2001)."

Jan 1, 2010

By Hongwei Zhang, Sen Yang, Shimin Liu

"This laboratory study investigates the damage evolution of sandstone specimens under two types of cyclic loading conditions through monitoring and analyzing the variations of elastic moduli and ultrasonic velocities. We adopted the rigidity degradation method for evaluating the damage accumulation through the rock dynamic ultrasonic velocity measurements. Compared to the ultrasonic test, the method of rigidity degradation shows deficiencies in the detection of damage development. The cyclic loading within the elastic limit led to a stiffening trend for the loading process but a softening trend for unloading process. The method of rigidity degradation was unable to describe the damage accumulation in this situation, while P-wave velocity clearly reflected the damage development. Moreover, a simplified model is established for interpreting the behaviors of the modulus variations and ultrasonic velocity. The cyclic loading within elastic limit enhances the anisotropy of rock, which causes a denser packing pattern in the direction of axial stress. The persistent damage accumulation under the cycling with an increasing upper limit is the consequence of the tensile failure in the microstructure of sandstone. INTRODUCTION The damage accumulation due to dynamic (cyclic) loading is highly detrimental in many engineering structures, such as mine openings, petroleum and natural gas boreholes, tunnels, rock foundations, and underground chambers. The sources of cyclic or repetitive loadings can be roughly divided into two types: (1) periodic operation, including drilling, blasting, and mining; (2) random vibration, including earthquakes and traffic loads. The repetitive loading-unloading process opens and closes the micro-pores and micro-cracks within the rock, further inducing the growth of cracks. As expected, the accumulating damage becomes a potential factor to trigger the rapid and violent failures of large-scale engineering rock structure."

Jan 1, 2017

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By WenFeng Li

Comparing to the coal seams in Eastern China, the coal seams in Western China usually have better geological conditions. Therefore, changes in the conventional gateroads layout are required for the Western longwalls. A case study based on a Western coal mine (LiMin) was presented to discuss the feasibility of an innovative gateroads layout. Based on the geological conditions, a 5m wide pillar between the adjacent two longwall panels, 09112 and 09113, was proposed in order to increase the recovery rate. More importantly, the entry supporting strategy of panel 09113 headgate needed to be determined and verified carefully since only 5m wide pillar was left to separate the entry from the panel 09112 gob. Three strategies with different supporting intensities in the panel 09113 headgate were evaluated by numerical modeling. The model outputs indicated that roof and rib boltings plus single hydraulic props were essential to maintain the gateroads stable. Field observation showed that under the proposed entry supporting strategy, the total roof-tofloor and rib-to-rib convergences were only 360mm and 460mm, respectively, during the service life of the panel 09113 headgate, which indicated that the innovative gateroad layout proposed in this paper is suitable for longwalls with similar geological conditions in Western China.

Jan 1, 2013

By Zbigniew Lubosik, Stanislaw Prusek

"The main elements of hard coal extraction systems in the Polish mining industry, including the characteristics of gateroads, are described, followed by several dozen underground measurements of gateroad roof sag performed in different geological and mining conditions in Upper Silesia Coal Basin.Based on the analysis of the roof sag measurements, an attempt to describe the gateroad roof sag process using a geometrical model was made. To build the model, it was assumed that the roof sag curve could be described by three straight lines. The first line describes the roof sag ahead of the longwall face; the second line, the sag at the longwall-gateroad junction zone; and the last line describes the zone behind the longwall face. Determining the intersection points and inclination angles is essential for the model. These model parameters depend on the geological and mining conditions in the gateroad.Using the statistical computations and analysis, the dependencies between the characteristic points of the gateroad roof sag model and the selected geological and mining parameters were defined. The STATISTICA computer program by StatSoft was used for computation.This paper presents a simple form of the geometrical description of roadway roof sag progression that is very useful during the gateroad support design process.INTRODUCTIONThe longwall system with caving is the dominant method in European mining in cases of hard coal seam extraction. For instance, in Poland, in 2009, 117 longwalls were driven, with total production of 77.5 million tonnes. In roughly 95% of the longwalls, mining operations were conducted using longwalls with roof caving; the remaining 5% used the hydraulic stowing system. The average mining depth was about 700 m (2,297 ft), and average daily output per face was approximately 2,600 tonnes per day. When using the longwall mining system, gateroads play an important role. These principal roadways transport materials, mine crews, and output. In addition, they impact ventilation of the extraction area, affecting, among other things, the climatic conditions or methane hazard. Unfortunately, difficulties often appear in maintaining an adequate size for the gateroads, due to the face line, which causes origination zones with stress concentration around the gateroad, resulting in rock mass movements in the form ofroofsag, floor heave, or horizontal convergence (Figure 1)."

Jan 1, 2010

By Enguang Zhu, Kangning Zhang, Yang Li

"Due to the use of outdated mining technology or room and pillar mining process in small coal mines, the coal recovery ratio is only 10% - 25%. In many regions of China: the damage area caused by the small coal mines amounted to nearly one hundred square kilometers. Therefore, special mining techniques must be taken to reclaim the wasted resource in disturbed coal areas. This paper focuses on the different mining methods by analyzing the longwall panel layout and abandoned gateroad (AG) distribution in in the abandoned area of Cui Jiazhai Coal Mine in northwestern China. On the basis of three-dimensional geological model, FLAC- 3D numerical simulation was employed. The abutment pressure distribution was simulated when the panel face passed through the disturbed areas. The proper angle of the inclined face was analyzed when the panel face passed through the abandoned gateroads. The results show that the head end of the face should be 13-20m ahead of the tail end. The pillars on both sides of abandoned gateroads had not been damaged at the same time, and no large-area stress concentration occurred above the main roof. Therefore, the coal reserves of disturbed areas can be successfully recovered by using underground longwall mining. INTRODUCTIONDuring the 70-90's, there were a lot of small coal mines in China. Due to their disordered mining, most of the small coal mines left a great many abandoned gateroads (defined as AG in this paper) and a large area of damage coal seam. In these type of coalfields, there exist many mining risk issues, including nonuniform stress in the overburden, flooding and hazardous gases accumulated in the gob. So how to lay out a longwall panel and successfully mining under this type of abandoned small mines is a big issue nowadays in China.As mentioned above, longwall panel is being performed in the damaged coal seams in order to increase recovery of coal reserves (Wang, 2009). However, the abandoned geteroads intersect to each other all around the area. So a series of production issues arose while the panel face is passing through these AG. Gang and Gong (2015) analyzed the roof stability and abutment pressure distribution during the face was passing those AG that were parallel and inclined to the faceline. Xie, et al. (2015) proposed the ground control mechanism by passing the AG in top-coal caving longwall mining. He recommended to stop the face advance until the roof is over, using high strength bolts and cable bolts, and grouting consolidation. This paper studies the different mining methods by analyzing the longwall panel layout and AG distribution in damage coal seams. Theoretical analysis and field observation were conducted to determine the overburden movement when the face was advancing under the AG. The pillar between face and parallel AG changes from elastic to plastic and eventually to the residual supporting status. All these three status was combined with the roof structure to establish the theoretical model to calculate the shield support capacity. Numerical modeling was employed to simulate the pillar stability and determine the abutment pressure distribution as the face inclined to the AG during longwall mining."

Jan 1, 2016

By Feiya Xu, Syd S. Peng

"As a highly efficient and new surveying and mapping technique, 3D laser scanning technology has been gradually applied to surface subsidence monitoring in mining areas. 3D laser scanning technology was used to monitor the mining subsidence in a coal mining area in this paper. Based on the 3D laser scanning data obtained in March, May, and December 2016 in the studying mining area, the surface subsidence basin and points deformation were acquired. The 3D laser scanning data were compared with that of the conventional surface movement surveying method. The results show that the 3D laser scanning technology could obtain the data of the subsidence basin more efficiently and reflect the true shape of surface subsidence caused by mining. The maximum surface subsidence obtained by 3D laser scanning technology was 3.60m, while the conventional surface movement surveying was 3.56m; the relative observation error between 3D laser scanner and the conventional surface movement surveying was less than 10%. Therefore, it is feasible to apply 3D laser scanning technology to monitor surface subsidence in coal mines.INTRODUCTIONWith the over-exploitation of coal resources, the problem of surface subsidence has become the focus of attention (Peng, 2011; Guo Wenbing, 2012). Setting up observation stations for surface movement was the traditional method to study the characteristic of surface subsidence and its parameters. At present, hundreds of observation stations have been set up in longwall mining, and a large number of measured data have been obtained (Ministry, 2017). However, due to the length of time surveying requires, great workload in the field, the high cost of observation, and difficult protection for monitoring points, conventional observation stations for surface movement have not met the research on surface subsidence. Therefore, as a new surveying and mapping technique, 3D laser scanning technology has been gradually used for surface subsidence monitoring in mining areas (Ma Liguang, 2005). Li Qiu, Qin Yongzhi, and Li Hong (2006) first proposed 3D laser scanning technology in the application of monitoring surface subsidence in 2006. It was showed that the 3D laser scanning technology had obvious advantages in efficiency and accuracy of data acquisition than other methods of deformation monitoring technology of surface subsidence (such as total station, precision level technique, GPS, etc.). Subsequently, Zhang Shu, Wu Kan, and Wang Xiang (2008) and Chen Ranli and Wu Kan (2012) analyzed the feasibility and precision of 3D laser scanning in subsidence monitoring, concluding that the 3D laser scanning can be used to obtain the subsidence basin and the monitoring precision can reach millimeter. Hu Dahe, Wu Kan, and Chen Ranli (2013) introduced the data processing method of 3D laser scanning for surface subsidence in detail. On the basis of a case study, the subsidence basin in subsidence area was obtained, which reflected the shape of mining subsidence basin intuitively and comprehensively. Wang Qisheng, Wu Kan, and Zheng Ruyu (2010) carried out the research on prediction parameters of mining subsidence by using 3D laser scanning data and got the parameters of major influence angle and the offset distance of inflection point. Meng Wanli, Cai Lailiang, and Yang Wangshan. (2017) made a profile analysis for the 3D view of the surface subsidence using 3D laser scanning data and put forward a “Geomagic” method of surface subsidence prediction."

Jan 1, 2018

By Steve Signer

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining effected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

Jan 1, 2004

By Christopher Mark

Dr. Christopher Mark serves as Team Leader of the Rock Mechanics Section in the Rock Safety Engineering Branch of the NIOSH - Pittsburgh Research Laboratory. In this position he leads a multi-disciplinary team and conducts individual research directed towards fundamental ground control safety issues affecting miners. Dr. Mark is recognized as one of the country?s leading authorities on coal mine ground control. Through his research, he has made numerous important contributions to mine safety that have been widely adopted into mining practice. He is a highly original researcher, and has often developed new and innovative methods to tackle extremely complex problems in his field. In recent years Dr. Mark has also achieved wide international recognition. Five research projects in Canada, Australia, and South Africa have been based largely on his work.

Jan 1, 2007

By Gamal Rashed

Coal bump is a sudden manifestation of the release of strain energy stored in a coal pillar (Peng, 2008). It is a very serious mining hazard that adversely affects the safety and productivity of the mines. Several case histories in mining have described coal pillars or faces of coal failing violently with an accompanying ejection of debris and broken material into the working areas of the mine (Campoli, 1987; Osterwald, 1962; Peperakis, 1958; Garvey and Ozbay, 2013). These failures resulted in large losses of life and total collapses of entire mine panels (Chase, Zipf, and Mark, 1994; Zingano, Koppe, and Costa, 2004). There are questions in the literature about whether or not the coal itself plays a significant role in bump. Rice (1935) mentioned that structurally strong coal is one of the key factors for bump; however, the strength of the Pocahontas #3 coal seam is low, and it bumped. Moreover, it is not obvious in the literature whether the strength of the tested coal samples is the inherent strength or if it is influenced by the shape or the size of the specimen. The main objective of this paper is to answer the following question: To what extent does the mechanical properties of the coal have an impact on the potential for violent failure? The best approach to answer this question is to compare the mechanical properties of two kinds of coals from bump-prone (Utah coal-Sunnyside seam) and non-bump-prone (WV coal-Sewickley seam). This comparison includes uniaxial compressive strength, modulus of elasticity, shear strength (cohesion and friction angle), and the burst index.

Jan 1, 2014