Search Documents

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920's. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950's. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By K. -A. Björkstedt

INTRODUCTION Strassa lies in the central part of Bergslagen, a tradi¬tional mining district, on the eastern side of the Stora Valley at an elevation of about 200 m above sea level. A railway siding runs between the mine and the Stora railway station from which there are railway connections to the shipping port and iron and steel works in Oxelosund, about 224 km away. The distance to the provin¬cial capital Orebro is about 60 km. The climate is typi¬cal for this part of central Sweden and is illustrated by the diagram of monthly precipitation and temperatures for the years 1968-1975 (Fig. 1). HISTORY There is no certain information as to when the Strassa mine was first worked, but it is known from sur¬viving accounts of mine inspectors that there were smelt¬ing works in operation in nearby villages in the 12th century. An example is the Gusselhytta ore smelting works, 10 km south of Strassa, which dates from this period. Around the year 1540 there were two smelting works in Strassa, the Upper Karberg and Lower Karberg works. Ore for these smelters was probably taken from Strassa and from the adjacent Blanka mine. In the year 1624 Strassa is mentioned by the painter Jons Nils Krook in an account of the iron mines in the Linde mining district (Linde Bergslags Jarngruvor). Several mines were listed in the area, the deepest being about 30 m. An impressive power installation is mentioned in 1639, including a piston system of lashed poles for transmit¬ting power from the Stora River to the Strassa fields. Its length was 2670 m. Common ground comprising about 20.2 km2 (5000 acres) of forest was allocated in 1689 for the furtherance of mining operations. Until the beginning of this century only the rich cen¬tral parts of the ore body were mined and these yielded, after handpicking, lump ore suitable for smelter feed. An example of the ore grades from these early times is an analysis of ore from the "Big Mine" (Storgruvan) from the year 1873: 48.5% Fe, 0.008% P, and 0.06% S. This same year a total of about 18 000 t was ex¬tracted from the Strassa mine. OWNERSHIP The mine was owned and run until 1874 by a min¬ing association made up of 119 so-called "bergsman," who were homesteaders often engaged in agriculture and timber-cutting as well. In that year the Strossa Grufvebolag (Mining Co.) was founded. In 1906 it was con¬verted into a joint stock company, the Strossa Gruveaktiebolag. This was acquired in 1907 by Metallurgiska AB for the implementation of Gustav Grondal's beneficiating and briquetting methods, for which the Strassa ore was well suited. The same year saw the completion of a new ore dressing plant with an annual production of 46 000 t of ore concentrate. In 1911 the mine passed to new hands, and in 1913 it was purchased by an Austrian company. Extensive new installations were made and in 1915 a new dressing and briquetting plant was completed with twice the capacity of the old one. In 1917 the Strassa mine was acquired by Granges. Be¬cause of unfavorable business trends and technical diffi¬culties, mining operations were brought to a close in 1923. Pumping kept the mine free of water until 1933 but it was completely filled ten years later. Up to 1950 the surface buildings and installations remained intact but the large dressing and briquetting plant burned to the ground in that year. Today only the machine shop re¬mains from this earlier period of operation, now housing parts of the Mineral Processing Laboratory. The decision to take up mining operations again was made in 1955 and construction work began the follow¬ing year. Of the old installation, only the "southern shaft" could be used for some development drifting after it had been completed with a new headframe. Other¬wise, all the buildings and installations required for the operations had to be rebuilt. New installations ready by 1960 were office and personnel facilities, a new shaft and headframe, a sorting and concentrating plant, a macadam plant, settling basins, pump stations, and a railway and yard with transport equipment. The instal¬lation was completed with two plants

Jan 1, 1982

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By S. K. Kawatra, S. Valluri

With increased CO2 emissions from steel and coal industry, there is great opportunity to capture CO2 and utilize the captured CO2 for economic advantage. The primary goal is to develop energy-efficient processes that reductively couple CO2, an abundant and renewable carbon source, for the production of value-added chemicals such as methanol, ethanol, and oxalic acid. These chemicals can be used elsewhere in the refining process or sold as valuable by-products. Geological sequestration, in comparison, has no economic return. Current CO2 utilization research at Michigan Technological University focuses on electrochemical reduction of CO2. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. This paper will present different ideas and their viability to utilize CO2 as a feedstock to produce several value-added compounds. INTRODUCTION Carbon dioxide (CO2) emissions into the atmosphere will need to be drastically reduced to curb the various undesirable effects of climate change. The large contribution in total CO2 emission originates from coal or natural gas power plants, and a considerable amount from steel plants. Average CO2 emissions in the US from steel industry is 2.9t CO2/t steel (Global CCS Institute 2013). Capturing the available CO2 from the steel and coal industries for economic advantage is a win-win situation for the industry. This technology is not only important scientifically but is also vital for a sustainable future. The various ongoing investigations can be categorized as biochemical, thermochemical, photochemical, and electrochemical approaches. Among these, the electrochemical method shows the most promise as an efficient form of CO2 conversion technology, because of its many advantages like high reactivity under ambient conditions and good extensibility from small- to large-scale processes1 BACKGROUND Extensive research has been done on the chemistry of transforming carbon dioxide into more useful products. Methods are known to convert carbon dioxide into a wide variety of substances, including methanol, isobutanol, carbohydrates, methane, carbonates, urea, formic acid, oxalic acid, carbon monoxide, epoxides, formaldehyde, and so on. Several of these (carbohydrates, formaldehyde, isobutanol etc.) are primarily results from biological processes. The rest are results of strong reduction reactions or electrolytic reduction. In short, electrolytic reduction can be used to form methane, methanol, formic acid, oxalic acid, carbon monoxide from carbon dioxide2. CO2 reduces at the cathode in an electrolysis cell. These processes have the general form of generating the carbon dioxide anion radical (2⋅−) and allowing it to react with itself or the electrolyte3. Catalysts can be added to influence the formation of the anion radical or to suppress side reactions3. The electrolyte, catalyst, voltage, electrode material and CO2 content are all known to effect the reaction pathway. Table 1 shows the overall reactions and energy requirements for electrochemical conversion of CO2 to chemicals

Jan 1, 2019

By William A. Griffith

The recent recession has severely impacted the performance and results of virtually all of our natural resource companies. The depressing climate continues to linger and recovery maybe sometime away. Problems remain for resource companies in the steel and petroleum industries as well as the mining business. In February, at the AIME Annual Meeting in New York, an All-Institute session presented a variety of views on the situation. A. T. Yu, chairman of ORBA Corp., Mountain Lakes, NJ, organized presentations by top management personnel of four natural resource companies. This well attended session heard management strategems for the present and views for the future. A compilation and synthesis of these presentations, gathered by Dr. Yu, are presented here for ME readers. Leading off will be William A. Griffith, president and chief executive officer of Hecla Mining Co., Wallace, ID. Other speakers presented here include Wilfred P. Schmoe, executive vice president of Du Pont Co., Wilmington, DE; Frank W. Luerssen, chairman and chief executive officer of Inland Steel Co., Chicago, IL; and Adam H. Zimmerman, president and chief operating officer of Noranda Mines Ltd., Toronto, Ontario. First, then Griffith's remarks. Introduction The key to successfully managing a natural resource company in austere times is good management in good times. In other words, position the company during prosperous times to survive the times when the well dries up. Although we know how to manage properly, for various reasons we sometimes do not do it. We forget the lessons of history. We allow ourselves to be carried away by our egos. We fail to position our companies properly in good times. As a result, in bad times we find ourselves in deep trouble. We need constant reeducation in the things we already know. In the natural resource industries, proper positioning in good times involves becoming a low-cost producer, retaining the flexibility to pull in our horns, developing a lean and effective organization, and maintaining a healthy balance sheet. Nothing improves the chance of survival during austere times as much as being able to produce at a lower cost than your competitors. In our business, that means having low-cost mines - low cost because the ore bodies are high grade or favorably located, and because they are efficiently operated. It also means recognizing the competition. The key numbers are the cost to produce an ounce of silver or gold. Nothing else really counts. And our competition is every other precious metal mine in the world. Flexibility is important when one gets stuck with a high-cost operation, often because things do not work out as we expect. It is important to be able to shut down an operation quickly and easily, without high holding costs, and without disrupting the corporate organization. A lean and mean, effective organization of competent people is vital during bad times. A company will not have that if it is not developed and maintained during good times. Finally, a natural resource company has to develop a healthy balance sheet during good times if it is to survive the bad. Money in the

Jan 6, 1985

By S. K. Mishra

Introduction The history of the Australian coal industry is almost as old as the history of Australia after new settlement. The first cargo of coal was exported from Newcastle to India in 1799. Coal has been mined in Australia for almost two centuries. But there are indications that the first coal was processed in 1877 in the Newcastle area. This is nearly 50 years after the first coal processing in Europe. Processing on any significant scale began in 1944 at the Newcastle Steel Works. In Queensland, however, coal processing did not begin until the second quarter of this century. The dramatic growth of mining and processing of Australian coal since the mid-60s is primarily due to the expansion of the export market in Japan, Asia, and Europe. Australian coals Black coal occurs in most of the major sedimentary basins of Australia. The better known deposits of commercial importance are in the Sydney, Bowen, Oakland, and Gailiee Basins. Apart from the Collie Basin in western Australia, other coal deposits of the Arckinga Basin in South Australia, the Bonaparte Basin in Northern Territory, and the Tasmania Basin are basically unexploited. The Sydney Basin of New South Wales and Bowen Basin of Queensland remain the major producers of black coal in Australia. Currently exploited or potentially commercial deposits of black coal in Australia occur in strata ranging in age from Permian to Tertiary. Estimated black coal reserves are summarized in Table 1. Coals from different ages have significant differences in their petrographic characteristics. Many of the Permian coals are usually rich in inertinite. Jurassic and Tertiary coals are typically rich in vitrinite content. Typical petrographic and chemical characteristics of some important Australian coking coals are summarized in Tables 2 and 3. The reserves of coking coals are restricted in the main to the Permian coals of the Sydney and Bowen Basins. Coal deposits in the latter are at shallow depth. A high percentage of these are being strip-mined. On the other hand, in the Sydney Basin, the majority of the reserves of good quality coking coals are at significant depth. The mining cost of these deposits is substantially higher than those in the Bowen Basin. It is usually possible to make strong coke with Australian Permian coals of vitrinite content much lower than the other international coals. But there are many major Permian deposits in Australia where low vitrinite content presents problems. As they are classified as marginal coking coals, optimization of their pro¬cessing plays an important role in meeting the market specifications of coking coal. The major reason for processing Australian coal is to reduce the ash content. Compared with British and some American coals, Australian coals are of relatively high ash content. Unlike American coals, more than 99% of the Australian coal deposits have sulfur content less than 1%. Consequently, sulfur control has never been a major problem. The coking quality of coal is improved simply through the ash reduction in the marketable product. However, with the increase in intensive mechanization and multi-stage handling of coal be-

Jan 9, 1985

By Carl H. Eckert, James P. Berson

INTRODUCTION The demand for specialty metals in industrial applications is in it's healthiest state since the late 1970'8, and several specific markets are recording record sales. Such metals as gold, silver, zirconim., titanium, beryllium, gallium, germanium, the platinum group, and the lanthanides accounted for sales in excess of $2 billion in 1985 among the end uses covered in this report. Although specialty metals as a group have suffered the effects of recessionary pressures in the past, these metals have proved more resiliant than such large volume metals as copper and nickel. This is due to the unique physical properties they possess which makes the threat of substitution or replacement through technological development uneconomic. The outlook for these specialty metals is optimistic in electronics, catalysts, ceramics, and alloys, and their specialty status results .in a combined average annual growth in demand of 7% through 1990. WHAT MAKES THESE METALS SPECIAL? Such characteristics as electrical conductivity, corrosion resistance, catalytic activity, thermal stability, and optical properties allow the term specialty to be applied to these metals. More importantly, all of these metals possess more than one of these qualities, as shown in Table 1. [ ] These five major functions are important in the end uses for these metals, although the specific applications vary somewhat. Conductivity in term of low or high electrical resistance is of obvious importance to electronics manufacturers. Producers of circuit boards or semiconductors require such metals as gold, palladium, platinum, and gallium due to their low electrical resistivity. However, these producers also require such metals as beryllium in the oxide form for insulation components because of the compound's low electrical conductivity. Although the lanthanides' conductive characteristics are not particularly attractive in electronics, they are of great importance to alloy manufacturers producing permanent magnets for automotive and computer applications. Corrosion and wear resistant properties are extremely attractive to a number of end-use industries, particularly in view of the estimate by the United States Bureau of Mines that $10 to $50 billion in losses are experienced by U.S. industry due to equipment corrosion and $100 billion due to equipment wear. The strength of high purity titanium and zirconium make these metals the obvious choice for corrosion and wear resistance particularly in the chemical processing industry, where the ability to maintain integrity in corrosive environments is a must. Heat exchangers, nuclear control rods, and a number of parts in jet engines have benefited greatly from the use of these metals. However, such other specialty metals as beryllium, and the lanthanides also improve the wear or corrosion resistance in various products. For example, a beryllium-copper alloy contact maintains it's spring like character, and does not loose this character after repeated use, which could result in the loss of an electrical contact. Lanthanide, in the form of cerium oxide, is commonly employed in alloys used to produce catalytic converter casings for the purpose of reducing damage by corrosive road salt. In some instances, the catalytic activity of several of the specialty metals assists in the economic production of other materials. However, the importance of specialty metals in catalysts is most apparent in catalytic converters for emission control. Platinum, palladium, and rhodium are

Jan 1, 1986

By Norman Weiss

The design of an ore-processing plant requires a high degree of cooperation among the geological, mining and metallurgical engineers. The purposes of this section are to provide mill design information most commonly needed by the mine planners and management, and to summarize the kinds of information that must be supplied to the mill designer to enable him to provide a suitable plant. 28.1-BASIS OF DESIGN NORMAN WEISS 28.1.1-SIZE OF PROJECT The size of the project generally is expressed in tons of ore milled per day, but company policies differ widely in this respect, a few adhering to this set figure but many expecting the design capacity to be liberal. To some companies that follow the latter practice a 25,000-tpd milling plant that cannot reach 30,000 or 35,000 tpd without major additions is a disappointment. The engineers responsible for planning the operation must know what is intended. Equally important are operating schedules, particularly the number of operating days per week and shifts per day for ore delivery, crushing, grinding and processing. Hours per shift also are an important factor in design, particularly in the case of ore delivery, and the percentage lost time expected for maintenance, cleanup, inspection, preventive maintenance shutdowns, and many others, has to be taken into account. Frequently, the ore deposit will vary in hardness and grade to such a degree that the capacity of the mill will vary widely from year to year and cannot be expressed as a fixed figure. but rather as an average over a calculable period, such as 10 yr, or as a specific daily capacity over the first 2 yr, next 4 yr, etc., or some similar projection. A good example of this kind of situation is Asarco's Mission operation 15 mi southwest of Tucson, Ariz., described by Weiss and Vincent.' where the major rock types differed widely in hardness, so that a change in the proportion of these types in the mill feed could have imposed difficult design problems if a constant tonnage rate had been expected. 28.1.2-EXPECTED LIFE The life of a mining operation depends upon the size of the deposit and the rate of mining. The latter is a policy decision based on an economic analysis which, in turn, is based on many factors.' From the point of view of mill planning, the estimated life of the operation determines many criteria and affects many decisions on strength of structures and degree of protection of men and materials, the quality of the materials-handling and process machinery, the type of delivery systems for ore to the mill and concentrates to the smelter or market, and many others. Costly installations that may be excellent investments for a 20-yr project may be wasteful for a 5-yr operation. An example is the comparison of different methods of crushing or grinding. Take single- vs. multiple-stage grinding-the former may be found more economical for a 5-yr operation, and the other, more costly, method more economical for a 15 to 20-vi- life.

Jan 1, 1973

By R. H. Goodman

The development of techniques for separating minerals based on differences in their specific gravities is reviewed and their present applications in process technology outlined. Special emphasis is placed on the development, in Australia, of new models of the spiral concentrator. The mechanics of separation of spiral separators are stated, including the effects of operating parameters, Some of the traditional areas of spiral application are described, together with examples of new applications such as treatment of fine alluvials and tailings, separation of liberated minerals at coarse sizes and fine coal recovery.

Jan 1, 1984

By D. Watson

The Henderson mine has more than 20 years experience and has placed a combined total of more than 400,000 m3 (520,000 cy) of shotcrete and concrete. Over the last 20 years the mine has used a variety of equipment for placing concrete, wet shotcrete and dry shotcrete and is constantly trying to cut costs and increase efficiencies. Henderson has recently received a state of the art wet shotcrete placer, automated its batch plant, fabricated a mobile concrete form jumbo and is soon to receive a new concrete transport truck.

Jan 1, 1992

By R. Keith Evans

Potential large scale uses in secondary battery systems and fusion reactors together with a steady increase in demand for conventional applications, particularly in aluminum smelting, has resulted in an increasing interest in lithium and its compounds. Current world requirements are met from both granitic pegmatites and non-pegmatitic sources and although the emphasis in this short paper is on the pegmatitic minerals, and, in particular, on their "direct usage" applications, a short summary of other sources and requirements for chemical production is included for the sake of completeness.

Jan 1, 1977

By M. P. Miano

Matching the productivity gains of continuous mining machines with the ever increasing performance levels achieved by longwall units has required creative thinking to assure that development is completed in time for uninterrupted longwall production. By using management information systems to coordinate support operations, the most productive planning decisions can be made. This paper focuses on the role of computer technology tools in achieving improved productivity from both longwall and continuous miner sections. The primary emphasis is on the planning process and the methodology developed to guarantee the best allocation of management and manpower resources.

Jan 1, 1993

By Donald H. Dowlin

The design of a preparation plant for minimum maintenance and clean up requires both the skills of the Engineer and the practical experience of the Operator. From the initial flow sheet and preliminary design until the plant is completed and operating, each phase of the work must be thoroughly explored for simplicity, workability and high efficiency. It is the responsibility of the Designing Engineer to develop the plant around the basic flow sheet, selecting equipment and materials not only with regards to Initial cost but also required upkeep and repair.

Jan 1, 1962

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument's ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand for the material. This paper develops a general method of evaluating these needs and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can be projected to establish future requirements. This demand forecast is critical to the evaluation of a new source of supply, such as the graphite resources of upper Michigan.

Jan 1, 1989

By T. B. Jarboe

The 150 MWe circulating fluidized bed (CFB) power plant described in this paper is the product of recent Bechtel experience in the industrial power and steam market, where the economic feasibility of fluidized bed projects has been proven. The inherent ability of CFB boilers to burn low grade fuels makes it possible to also burn low ranking coals or coal wastes, including anthracite culm, coal mine rejects, and coal wash plant waste slurry. The impact of fuel characteristics on plant design is addressed. This includes solids handling, steam generation, sulfur capture, and auxiliary load requirements.

Jan 1, 1988

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By J. G. Russell

The valuation of known mineral re-serves entails the economic evaluation of the mining enterprise and the valuation of other assets employed, including mining and processing plant and intangible assets. A case study approach analyzes two reserve situations: ownership of reserves (phosphate rock), and leasing of reserve lands (kaolin). The appraisal of the physical property is outlined, along with the economic analysis of the operation. The discounted net cash flow approach is used to value the enterprise, leading to value of the reserves after correlation with other assets employed.

Jan 1, 1989