Search Documents

By J. Finch, J. Yianatos, N. W. Johnson, R. Espinosa-Gomez

A method of determining the maximum concentrate solids rate or carrying capacity is described for given column operating conditions. The method requires alteration of the feed rate of solids to the column at a fixed residence time by manipulation of the % solid of the column feed pulp or the bias rate. The carrying capacity was measured for five streams at the Mt. Isa Mines Pb/Zn and Cu concentrators. As a potential scale up parameter, the mass of solids per unit time per unit column cross section (Ca, g/min.cm2) is explored. Ca is tentatively related linearly to the 80% passing size (d80) of the concentrate. For d80 < 15 pm Ca was less than 4 g/min.cm2 (8 lb/min.ft2) which makes it a critical consideration in scale-up for such fine feeds. An alternative carrying capacity parameter, mass of solids per unit volume of gas Cg was not as useful as Ca since Cg varied inversely with gas rate.

Jan 1, 1988

By V. G. Papangelakis, G. P. Demopoulos

The high temperature (180-200 OC ) pressure oxidation (02 - HzSO4) process for the recovery of gold from refractory concentrates (FeS2/FeA8S) is simulated with the aid of a computer model. The model centers on the continuous operation of a multi-stage horizontal autoclave. In particular the effects of key process parameters controlling the autogenous operation of the autoclave are critically examined. The building elements of the model are (i) the continuous particle size distribution function of the concentrate, (ii) the residence time distribution function of the slurry and (iii) the shrinking core kinetics. Conversion is calculated on the basis of the segregated flow model. For the calculation of the particle size distribution at the exit of each compartment the population balance model is employed. The effects of feed rate, feed preheating, cooling, autoclave configuration and rate limiting regime (chemical reaction vs. gas-liquid mass transfer) on the autogenous steady state operation are discussed. Finally optimum reactor design and operation criteria are indicated.

Jan 1, 1990

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By Richard R. Klimpel

The author was the banquet speaker at the 48th Annual MPD meeting, sponsored by the SME Colorado Minerals Processing Section, May 14-16, 1998, in Colorado Springs, CO. Here are his remarks. It has been an exciting experience to have spent 34 years involved with the process of generating patented technology eventually leading to commercialization. In today&apos;s terminology, this process is called technology transfer. I have had the unusual experience of being involved doing basic research as an inventor while also being responsible for managing new product development and commercialization. In addition, I worked for 31 years before my retirement for a large research-oriented company, The Dow Chemical Co. In 1995, the company spent more than $1 billion dollars on research and development. The last three years of my career have been spent working with a research-oriented university, The University of Florida. And I have worked as a consultant helping several companies to optimize their products and processes. It is on this cumulative experience base that the preparation of this article is based.

Jan 1, 1998

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By J. N. Carras, N. W. Bainbridge

In order to further the understanding of spontaneous heating of longwall goafs a numerical model was developed, based on conservation principles applied to the transport of heat, water vapour and oxygen across the god Advective air flow into the goaf is caused by the differential air pressures across the god The air velocity field within the goaf area was computed using Darcy&apos;s law. The boundary and initial conditions concern air pressure, temperature and relative humidity. The oxidation rates and heat generation rates of the goaf materials required for the simulation were obtained from laboratory measurements. The main outputs of the model are temperature, oxygen and water contour maps, the rate of air leakage into the go4 velocity field and pressure distribution across the god. The model while still in its development stage, is able to simulate a heterogenous goafs constructed from different materials with different thermal and mass flow properties. Validation of the model by comparing its output with measurements from within goafs is required before the model can be used with confidence in a predictive sense.

Jan 1, 1995

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994

By Rimas Pakalnis, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

Jan 1, 2005

By Carlo Grandori

Foreword In loose ground and soft rock formations, mechanical tunnel boring is necessarily dependent on the adoption of shield machines and the application of adequate support or lining structures. These structures are erected either within or immediately behind the rear portion of the shield and provide the required reaction to the forward thrust. In competent rock formations where systematic support is not a requirement, hard rock tunnel boring machines generally advance by thrusting from a structure gripped against the tunnel walls. These machines may feature a more or less extended cutterhead shield or roof support, but when in weathered, fractured or otherwise weakened ground, or in fault zones filled with soft gouge, the gripper mechanism often cannot provide enough thrust reaction to advance the cutterhead. Under these conditions, early support of the arch and walls is generally required in the form of rock bolts, steel rings and laggings and some times of a primary concrete lining placed in the short section between cutterhead and grippers. Such tunnel support measures generally fail to produce an adequate increase in thrust reaction capacity, but

Jan 1, 1976

By Martha Caudill

When planning for the required amount of storage capacity at a proposed open-pit coal mine or determining when additional storage capacity should be added to an existing operation, the decision must be based on a breakeven- analysis relating the discounted cost of capital for storage capacity to the marginal costs incurred for additional crew call-outs on weekends and demurrage charges. The model developed in this paper uses simulation techniques applied to two coal mines in the Powder-River Basin to determine how much storage capacity is needed and when it is needed. The paper also generalizes the simulation model so that it can be applied to any type of open-pit mining operation. Two important results of the model are (1) all of the mines in the Powder River Basin have excessive amounts of storage capacity, and (2) management is provided with estimates of the total number of hours that crews will have to work on the weekends as annual tonnage increases, and the levels of demurrage costs incurred.

Jan 1, 1986

By C. Haycocks

In spite of the increasingly high capital investment required for longwall mining equipment, there continues to be a steady trend towards this form of mining. This move is caused in large part by improved productivity of longwall mining systems combined with greater percentage of coal recovered over room and pillar mining, reduced manpower requirements, and the inherent safety of the system. Longwall mining is most amenable to the greater depths experienced by many mining operations, particularly in the coalfields of the Eastern United States. Two primary problems in the installation of a longwall panel are determining whether a particular seam is suitable for longwall and, secondly, type and capacity of equipment required for such a mining operation. In addition, recent legislation has forced an evaluation of the surface effects of longwall mining with a view to determining what, if any, surface damage might result from extracting any particular panel. These factors must be determined using large and often complex quantities of geological, structural, mining, and surface data. This makes the problem most attractive to solution using the computer.

Jan 1, 1979

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson&apos;s equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By Felicia F. Peng, Wenguang Wang

The purpose of this research work is to predict the dust concentration distributions of different particle sizes on longwall faces. This Is necessary because the dust sources must be identified before dust control techniques can be recommended and applied correctly. The dust concentration data at longwall faces were determined by using Real-time aerosol monitors (RAM-1) and gravimetric monitors. However, these field data cannot explain the nature or the mechanisms of dust flow phenomenon on longwall face. Therefore, a mathematical model Is developed taking Into account the characteristics of airflow, the natures of dust generation and particles, the mechanisms of dust transport and deposition as well as the multiple dust sources on the longwall faces. In this paper, the identification of respirable dust sources on the longwall faces are determined. The dust particle size distributions In various longwall faces are analyzed and classified. The comparison analyses of field data and model predictions are presented. Specifically, the general trends of dust concentration on the longwall faces obtained at different positions and at various conditions are discussed.

Jan 1, 1991

By K. I. Cunningham, C. S. Spirakis

Two types of native sulfur deposits have been found in Lechuguilla Cave: thin late-stage crusts and massive early- formed deposits. Most, if not all, of the crusts appear to have formed by remobilization of native sulfur contained within gypsum and sulfur masses. The process is occurring today and is slowly converting the sulfur to gypsum. The absence of primary gypsum or reductants in the cave indicates that the early-formed massive sulfur deposits did not form by in-place reduction of sulfate, which is the process that formed the commercial sulfur deposits in the Delaware basin. Instead, it appears that H2S dissolved in basinal brines was oxidized by oxygen in near-surface ground waters in the cave. Fluid- inclusion data, which suggest the presence of both fresh water and saline water as the sulfur formed, support this interpretation. Although individual sulfur deposits in Lechuguilla Cave are no more than several tens of metric tons, the abundance of secondary gypsum (as much as 10 meters thick) indicates that native sulfur may once have been much more extensive.

Jan 1, 1992

By P. Somasundaran, Bruno Lartiges

Two different groups of mechanisms have been considered in the past to explain the effects of chemical additives on grinding. While one group of explanations is based upon alterations of surface and mechanical properties of the individual particles, the other group depends mainly on the arrangement of particles and their flow in suspensions. In this paper some of the past work on grinding aids is reviewed and attrition grinding of a commercially important ceramic material, zirconia (stabilized with yttria) with polyaaylic acid as grinding aid, is studied in order to determine the effect of the aid on the ground product itself. It was observed that even though polyaaylic acid did cause a drastic decrease in the viscosity of the pulp, it did not have any major effect on the grinding of zirconia at least up to 2000 ppm and only minor detrimental effect above it. Importantly, complexation by the polymer was found to cause extraction of yttrium into solution with possibly significant changes in the surface chemical composition of the product.

Jan 1, 1992

By Abdullah Arik

The resource classification methodologies have always been a topic of research and debate. There are both traditional and Geostatistical methods used in practice. Because of the uniqueness of each ore deposit, it seems almost impossible to have a single industry-accepted norm for resource classification. Therefore, some practitioners have adapted the methodologies to suit the deposits they are working on, but many simply use the methods they are comfortable with. Another reason for the existence of varying classification methodologies is the lack of an easy and established way to measure the confidence in the estimates. Therefore, their classification becomes a subject of debate. In this paper, a new approach is offered to classify the resources using a "Resource Classification Index." The approach using this index takes into account the local variation, the spatial data configuration around the block being estimated, as well as the traditional distance measures. A case study for a gold deposit is presented to demonstrate how this new index can be used to classify the resources. The results from this approach are compared to those from two popular classification methodologies.

Jan 1, 2002

By K. S. E. Forssberg, S. Subramanian, Hanumantha K. Rao

The dispersion characteristics of apatite and magnetite minerals have been assessed based on zeta-potential measurements, using various inorganic and organic reagents, namely sodium silicate, sodium tripolyphosphate, sodium hexametaphosphate and lignin sulphonate. These results highlight that apatite is dispersed to a greater extent vis-à-vis magnetite. Further, the dispersion efficiency of the phosphate reagents is better than that of sodium silicate or lignin sulphonate, for both apatite and magnetite. Batch flotation tests on a high phosphate magnetite ore from Kiruna indicate that higher apatite recovery with minimum phosphorous loss to the magnetite fraction can be achieved using sodium silicate as a dispersant. Although comparable dephosphorization can be attained with lignin sulphonate dispersant, the recovery of magnetite in the non-float fraction is lower, possibly due to the adverse synergistic effect of this organic reagent with the Atrac collector, resulting in the flotation of magnetite. The high intensity conditioning of pulp for up to 30 min resulted in better apatite flotation with <0.015% phosphorous in the magnetite product.

Jan 1, 2002

By Richard Crawshay, Duncan Hutchison

Continuous Mining Systems Limited have developed an efficient, high-capacity, in-line loading unit capable of handling shot rock in tunnel driveages at extraction rates up to 970 tonnes (1,000 tons) per hour. A smaller 408 tonnes (450 tons) per hour loader is also available These in-line loading units called "Osciloaders"® provide a continuous flow of material from the muck pile to an anciliary conveyance eliminating the cyclic or interrupted movement noramlly associated with gathering arm or bucket type loaders. The osillating lip fluidizes the material, reduces the penetration force required and facilitates and regulates the material flow onto the adjacent conveyor. The conveyor is wide and accommodates very large material with ease, transporting and elevating it to a height suitable for a waiting conveyance at the rear of the machine. The "Osciloader"® is currently being utilized for production mining by a major company in Sudbury, Ontario. Both truck and conveyor anciliary haulage are being utilized. The paper describes the development of the loader and how it may be applied in tunnelling applications.

Jan 1, 1987