Search Documents

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By C. J. Bise

Virtual reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced form of computer graphics. The images are generated based on where the user looks and how the user moves. As personal-computer-based (PC) instruction gains acceptance as an innovative approach to providing safety training, VR can provide a multisensory, rather than merely a multimedia, mode of presentation. New technology continues to be introduced into the mining industry to meet the productivity needs of coal and noncoal producers. There is also an increased need for more innovative training of mine workers. New technology and equipment designs often affect the basic causes of accidents. For example, the development of cabs and canopies for underground coal-mine equipment has reduced the number of accidents related to roof falls and rib rolls. However, safety-training specialists then had to focus on the machines themselves, because the modifications had the potential for causing "pinch-point" accidents. In fact, although the overall physical demands on mine workers have diminished, there has been an escalation in the concerns about trauma from repetitive physical activity. Thus, health-and-safety training specialists have shifted their atten¬tion to the recognition, evaluation and control of workplace hazards (Hancock and Hill, 1995). Recognizing that the spatial relationships of a workplace convey more information about hazards when experienced rather than described, trainers agree that simulation is the method of choice. Unfortunately, until recently, simulation systems were either simple software programs that did not come close to portraying the real experience or were complex hardware systems (such as flight simulators) that did, but at a cost of millions of dollars (Fritz, 1991). However, researchers and training specialists are excited about an emerging approach to work-force education based on virtual reality. VR is also described as cyberspace, immersive simulation, artificial reality, telepresence, virtual environment or virtual world (Meyer and Dunn-Roberts, 1992; Peterson, 1992). It represents a group of concurrent advances in computer and interface technologies. They enable an individual to interact in a multisensory way with a computer-generated environment. To achieve this, a typical VR system incorporates a computer that contains the necessary databases for producing realistic images and audio; a head-mounted display (HMD) or screen for viewing the images; and a three-dimensional controller, joystick or data glove for interacting with the computer-generated environment. If virtual reality is to become an effective tool for the safety training of mine workers, its attributes will have to be measured against other forms of delivery. Accordingly, Carr (1992) listed the following areas in which VR should be considered the method of choice: ? When training mistakes would be costly. ? When the necessary environment cannot be experienced in the real world. ? To build interfaces that are sensible and can be manipulated. ? To make training situations really "real." ?To make perceptible the imperceptible.

Jan 1, 1997

By W. J. Douglas

Before discussing minicomputer software for the mineral industry, it is helpful to explain some of the computer program terminology. Most of the terms are the same as those applied to large computers. A computer system consists of a machine (hardware) with electronic and mechanical components and instructions (software) that define its operational logic and sequence. This logic is described by sets of commands grouped into programs. Each program has specific objectives related to the computer's operation and to production information from computer data that are input and processed. Software, therefore, is a general term applied to any type of computer program. Instructions to the computer are communicated through languages that convert logical and arithmetic statements into machine operations. The languages may consist of statements resembling mathematical or logical phrases understandable by humans, or they may be coded statements with no apparent resemblance to spoken language but readily understandable by the computer. Computers also translate higher level languages such as FORTRAN or COBOL into machine languages using other programs called Compilers. Programs written in these higher level languages are generally called source code. However, programs written in computer assembly language may also be called source code. The compiled version of the program after it has been translated by the compiler software is called object code. Programs used to "instruct computers how to be computers" are generally called systems software. They relate more to computer operation than to producing externally usable results. Programs producing information for many users-engineers, accountants, managers-are termed applications software. For the most part, applications software is the principal concern of the mineral industry. Programs are developed to fit user requirements as interpreted by programmers. Programs vary in quality, precision, efficiency, accuracy, and complexity, depending on programmer skills and abilities and programming decisions forcing design tradeoffs. A well written program should have speed, efficient use of available hardware resources, accuracy, and an inherently logical structure that aids documentation and subsequent modifications. Programs developed to fit specific requirements are termed customized software. A program organized and prepared for general commercial use is called a package, or a software package, and includes documentation for program use. A form of customized software that takes an existing program or package as its starting point and modifies it is called a customized package. A minicomputer program can be stored on computer cards, standard magnetic tape, magnetic cassette tape, floppy disk, or hard disk. The software purchaser or lessee may select one or more of these media when specifying a program in a software contract. Supporting documentation may include a listing of the program instructions linkages, hardware and storage resource requiremnents, flow charts, and programmer and user manuals. The purchaser must carefully make and clearly understand specifications for media and format of program delivery. This assures that delivered software is compatible with the intended hardware. Mineral Industry Attitudes Toward Computer Software The mining industry has traditionally been conservative concerning computer applications. Furthermore, large computer costs have made these systems accessible only to large companies, for the most part. But in the past few years, mining software systems developed at schools such as Pennsylvania State University and Virginia Polytechnic Institute have gained wider acceptance in the mineral industry. More mining engineers now have academic training in computer application, and computer use is now more acceptable to the mining industry. Mining managers in decisionmaking positions are faced with a new generation of computer technology resulting from the rapid evolution of minicomputers. Not too long ago, manufacturers such as Digital Equipment Corp., Data General, and Hewlett-Packard were considered newcomers. They are now established companies. In addition, Apple, Radio Shack, Commodore, and others have emerged in the growing microcomputer industry. So the mine manager or mining executive now has more options. Mining Software is Limited Along with the rapid evolution in hardware development, much general purpose software is now being developed for minicomputers. The 1981 Apple Software Directory can be obtained for about $14; Radio Shack published the Application Software Source Book in three volumes for $1.95 each. Brochures describing software can be obtained for other minicomputer manufacturers by contacting local sales representatives. Hewlett-Packard software can be obtained and exchanged through HP user's groups. Manufacturers' programming staffs are generally concerned with developing applications software. In some instances, manufacturers will recommend software developed by their hardware users. Until now, however, software development for mining applications has been minimal. This should not be surprising, since software development traditionally lags hardware development by several years. A review of A Directory of Computer Software Applications/Mini-Computers and Micro-Computers, August 1977-1980, published by the US Department of Congress, National Technical Information Service, contains many entries and subject areas. General applications include some references to tunneling machines, but there are virtually no entries specifically relating to

Jan 11, 1981

By J. P. Ferro, W. H. Stewart

Wet ground and dry muscovite mica continued to be the most commercially significant types of mica in the US. Canada's phlogopite mica and some US deposits of sericite mica have also contributed to the overall application of mica in a variety of industries. Mica's major end uses are paint, rubber, and construction material. Its value was about $30 million last year. The southern Appalachian Mountains weathered granitic bodies and pegmatites continued to be the primary US muscovite mica source. North Carolina production of mica as a coproduct of feldspar, kaolin, and lithium processing accounted for more than 60% of the total output. New Mexico, South Carolina, South Dakota, Georgia, and Connecticut accounted for the rest. Flake mica was also produced from mica schists in North Carolina and South Dakota. It is also being investigated in Ontario, Canada. Wet ground mica Wet ground mica was produced by four companies: KMG Minerals, Franklin Mineral Products, J.M. Huber Corp., and Concord Mica. KMG and Franklin Mineral Products accounted for more than 80% of the production. Wet ground mica is a highly delaminated platey powder used to reinforce solvent and aqueous system paints for increased weatherability, durability, and greater resistance to moisture and corrosive atmospheres. In plastics, it is an excellent filler and reinforcing agent, providing better dielectric properties, heat resistance, and added tensile and flexural strength. In the rubber industry, wet ground mica is used as a mold lubricant to manufacture molded rubber products, such as tires. It also acts as an inert filler that reduces gas permeability. Miscellaneous uses include additives to caulking compounds, foundry applications, lubricants, greases, silicone release agents, and dry powder fire extinguishers. Wet ground mica prices range from $353 to $496/t ($320 to $450 per st) fob plant. Specialty products may be higher, depending on customer requirements. Dry ground muscovite mica Dry ground mica was produced by nine companies: KMG Minerals, Unimin, US Gypsum, Mineral Industrial Commodities of America, Spartan Minerals Corp., Asheville Mica Corp., Deneen Mica Co., Pacer Corp., and J.M. Huber Corp. Dry ground mica's primary market is wallboard joint compound. Here, it is a functional extender that improves the physical properties and finishing characteristics of the mud. It is also used in various grades as a filler in asphalt products, enamels, mastics, cements, plastics, adhesives, texture paints, and plaster. Dry ground mica became popular as an additive in oil well drilling fluids, where the mica flakes platey nature helps seal the well bore, preventing circulating fluid loss. But oil's dramatic price drop and consequent curtailing of well drilling brought this once booming market to a virtual halt. Forecasters predict that this business will gradually pick up during the next few years and most current dry ground mica producers will again produce the oil well drilling material. Dry ground mica prices range from $110 to $420/t ($100 to $380 per st) fob plant. High quality sericite mica, sometimes referred to as an altered muscovite, was mainly produced by two US companies. Mineral Industrial Commodities of America and Mineral Mining Corp. have equivalent capacities of about 27 kt/a (30,000 stpy). The majority of the material produced was consumed by the joint compound industry. Minor uses are in paint and oil well drilling. The lack of ground sericite penetration into the traditional ground muscovite markets is attributed to high silica content, typically in excess of 20%, and a bulk density. Prices range from $88 to $187/t ($80 to $170 per st) fob plant. Phlogopite mica is a dark colored, magnesium bearing mica rarely found in the US. Suzorite Mica Corp., a division of Lacana Petroleum, mines a deposit in Quebec that is 80% to 90% phlogopite. The dark color has prevented the material's entry into the traditional paint markets. But the physical properties and high purity make it useful as a low-cost reinforcing filler in many plastics and several asphalt applications. Phlogopite mica is ground to several grades and may be treated with various surface coatings for use in plastics or coated with nickel for EMI/RFI shielding applications. Prices for phlogopite products range from $144 to $580/t ($104 to $580 per st) fob plant. As in recent years, production of domestic muscovite sheet - block, film, and splittings - remained insignificant. These resources are limited and uneconomic due to the high cost of hand labor required to process sheet mica in the US. Imports from India and Brazil were the primary sources of the estimated 1 kt (2.4 million lbs) valued at $2.5 million consumed by US electronic and electrical equipment manufacturers in 1986. Reserves As a feldspar, kaolin, and lithium industry coproduct, flake mica will continue to provide a large percentage of mica re- This summary of 1986 mica activity was received too late to be used in the June issue.

Jan 7, 1987

By Friedrich Steinhäusler

RADON SOURCES AND CONTROL MEASURES IN THE MINING ENVIRONMENT Most of the contamination of the mine atmosphere by radon 222 is due to radon emanating from solid or fractured ore surfaces of walls, roof and floor. Also radon gas emanates from broken ore either from storage in backfilled mined-out areas as applied in e.g. shrinkage stopping methods or from ore spillage along intake airways mainly due to the use of trackless haulage. To a lesser extent water itself can represent an additional source of radon, which emanates into air from open drainage ditches or seepages along intake airways. The contribution from water can be controlled effectively by isolating the water from the primary intake air system, e.g. by diverting the water through pipes and/or sealing of seepages by grouting. However, control of radon emanating from rock surfaces creates a major technical problem with significant impact on the economic aspects of mining operations, if adequate radiological conditions must be maintained. Basically this can be achieved by suppressing the emanation process itself, confining already emanated radon or by removal of radon from the mine atmosphere. Extensive research has been carried out on the rate of radon emanation as a function of barometric pressure changes (Pohl-Rüling and Pohl, 1969). It could be shown that the radon supply consists of a permanent and variable component. The former results from the surface of the rock and depends mainly on the emanating fraction of its radium 226 content; the latter originates from within the rocks and is a function of the suction effect of decreasing barometric pressure, rock porosity and fissures. The practical application of this barometric pump effect for depressing the rate of radon emanation, e.g. by pressurizing the mine atmosphere, is limited due to high costs for providing a sink for absorption of radon and air as well as lack of permeability in most uranium ore bodies (Schroeder et al., 1966). Mine air cleaning by removal of radon can be achieved with the use of cryogenic methods, chemical removal, adsorption into charcoal beds, use of a gas centrifuge or general ventilation techniques. Technical problems have so far prevented the application of any of these methods other than ventilation. It is common practice to use the age-of-air concept, i.e. fresh air is delivered to the worker as directly as possible and removed quickly afterwards thereby maintaining the air "young". Engineering principles for quantity distribution of air through underground working areas are straightforward for general mining situations where radon constitutes an environmental contamination problem. However, in cases of high uranium ore content this concept may result in high costs with regard to installation and energy requirements for effecting both frequent air changes as well as sufficient heating of the air in cold seasons. Taking into account that the investment in ventilation systems is a major cofactor for the overall ore production costs this can be a limiting and decisive component in the assessment of the economic feasibility of specific mining operations and mineral reserves in general. Effective control of the radon flux from the rock surface prevents the initial contamination of the mine air with radon directly at the source. A radon diffusion barrier for practical application in mining requirements should fulfill the following requirements: - reduction of radon emanation rate by at least an order of magnitude - high mechanical strength - ease of sealant application onto surface to be coated - water resistant - low fire hazard - resistant to temperature changes encountered in mines - high cost efficiency in relation to exposure reduction achieved (direct and indirect costs) - low degree of maintenance. In the past several materials have been tested as sealants for controlling the emanation of radon from surfaces of rock and building materials. Epoxy paints reduce radon emanation rate only by a factor of 2 to 6 (Auxier et al., 1974; Eichholz et al., 1980; Keith Consulting Engineers, 1980). Although it is possible to prevent the escape of more than 99 % of the radon to the environment with gel seals over 80 mm thick (Bedrosian et al., 1974), practical applicability is very limited. Multilayer coatings of epoxy resins with various additives require meticulous preparation and flawless application of seamless four-layer coatings in four days to impede radon diffusion (Culot et al., 1976), otherwise results from this method have not been totally satisfactory (Leung, 1978). Aluminium foil laminated with polyethylene and paper on each side is under test as radon barrier but results are not available yet (Ericson, 1980). However, this method has the inherent disadvantage that possible malfunctioning electrical installations can cause fire or electrical shock through the sealant. Polyurethane foam coatings have been used on stoppings as very effective sealants. It does, however, represent a potential danger of spontaneous ignition and it is expensive (Rock, 1975). Thus, there is still need for a material which has similar properties as outlined above. In the following results are reported from investigations on the suitability of various materials as radon diffusion barriers.

Jan 1, 1981

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

1.1 GENERALIZED METHODS OF SUPPRESSING THE INFLOW OF GROUND WATER DURING THE CONSTRUCTION OF SHAFTS, DRIFTS AND TUNNELS Various methods are used to prevent or minimize the inflow of ground water into underground workings during their excavation. The two most common methods include freezing the saturated rock and grouting using cement, sodium silicate, polyurethane and/or other chemicals. Each of these technologies for combatting the inflow of ground water is effective only under specific hydrogeological conditions. For example, although the freezing of saturated ground is among the more universally adopted methods, it is designed to provide only temporary protection during construction. Before the saturated rock thaws it is necessary to emplace a waterproof liner which is labor intensive, time consuming, and expensive. Consequently, freezing is used only in exceptionally complex hydrogeological conditions, namely in those cases where the water-bearing strata consist of unstable rock or the ground water has an anomalous hydrochemistry. The classical grouting of saturated rock, carried out from the surface or from the face of the underground workings for the purpose of limiting the inflow of ground water during excavation, utilizes both cement and a variety of chemical grouts. Cement grouting has been regarded as the main method of combatting the inflow of ground water in fractured rock throughout the world. In such countries as the Federal Republic of Germany (FRG), Canada, the Republic of South Africa and Great Britain, cement grouting is the main method of reducing the inflow of ground water during the excavation of mine openings. In Great Britain and the FRG, cement grouting has been used in 80% of all shaft excavations. In the Republic of South Africa cement grouting has been used in almost 100% of all the shafts that have been constructed. The installation of grout curtains into permeable water- bearing strata significantly reduces their permeability and increases the rock strength. Grouting has the greatest effect in fractured sandstones, certain well indurated shales, fractured granites, fractured quartzites, and karstic limestones or dolomites. The following principal factors must be considered when assessing the expediency of grouting rock with cement: the geometry of the network of fracture openings, the saturated hydraulic conductivity of the fractured rock, the hydraulic head acting on the water in the rock, and the chemical composition of the ground water. On the basis of the geometry of the fractures and the thickness of each hydrostratigraphic unit, the characteristics of the cement grout are selected. As a rule, the cementing of large fractured zones with high ground water velocities is carried out using inert fillers (sand, mill slag, loam, loess, crushed limestone), special types of cement, setting accelerators, and high cement concentrations in water. Calcium chloride, soda ash, sodium silicate, sodium nitrate, amino alcohols, tin bichloride, trisulphate nitrate, and lumnite are used extensively as the setting accelerators for cement grouts. In the FRG and Poland, special cement injection compounds that embody a mixture of cement and active cement metal salts, water additives and binding substances are being used for the cementing of saturated zones with rapid ground water velocities. These reagents accelerate the rate of structure-forming reactions. In spite of the wide variety of additives used for cement grouts, the effectiveness of the method in large fractures below the water table is either poor or it leads to a very large consumption of cement due to the erosion of the grout through the cracks before it hardens. At the present time, a large number of cement types and brands are being produced by various countries. These variations permit cementing to be employed in a variety of geological conditions. However, both pure cement grout and grouts with fillers constitute unstable systems with a high water loss rate. Therefore during the grouting of finely fractured rock the cement grout's premature loss of a large amount of free water causes its consistency to increase, whereupon the grout solidifies. Consequently, it inadequately penetrates into the fine fractures of the stratum. In addition the high water loss rate in the cement grout causes unreacted cement particles to remain, which greatly reduces the grout hardness and the resulting rock strength characteristics are weakened. As a result, the binding properties of the cement are utilized perhaps up to 60%. The remaining portion is left in the grout as a filler. All these conditions significantly decrease the efficiency of the isolation effort both with respect to strength and cost. In order to expand the cement grouting method, re- search is being conducted to improve the quality of cement grout, to increase its range of application with respect to permeability control, to reduce its water loss rate and to increase its capacity to withstand the erosive and corrosive effects of poor quality ground water. For example, mixtures of bentonitic clay, carboxymethyl cellulose, aerated sodium sulfide, sulphated alcohol distillery waste, nitrolignin, gip-

Jan 1, 1993

By Nelson R. Shaffer

Biotechnology has become a household word of the nineties, and it is expected to become as important in the next century as the computer is in the present. Numerous books and articles portray biotechnology developments as nothing less than a scientific revolution. Almost everywhere one looks new biotechnical breakthroughs are being reported that offer almost limitless opportunities to harness the force of living things to produce materials and manipulate their properties. Biotechnology has been broadly defined as any applications of biological organisms, systems, or processes to manufacturing and service industries. This seemingly new technology is, in fact, one of mankind's oldest scientific activities (Table l), which has been recently revolutionized by techniques of genetic engineering that arose out of basic research in biology, biochemistry, genetics, and information sciences. From fields as old as agriculture and medicine to those as new as monoclonal anti-bodies, transgenic plants, or biocomputers are encompassed by biotechnology. Like most human endeavors, industrial minerals play critical roles in biotechnology. In addition biotechnology holds real potential to improve extraction and beneficiation of certain industrial minerals themselves. BIOTECHNOLOGY OVERVIEW Companies using established biotechnical techniques make up large and diverse groups such as agriculture, chemicals, and pharmaceuticals. The massive US Pharmacopia (Anon., 1990a) provides detailed specifications for minerals used in medicines. Alumina, zirconia, apatite, and bioactive glass have seen service as implant materials (Williams, 1990) and new uses for minerals in health sciences are being actively researched. Agriculture produced $361 billion worth of food and drink during 1991 in the United States; organic chemicals, pharmaceuticals, and enzymes accounted for $68, $59, and $42 billion, respectively (Anon., 1992a). It is not possible to separate the contributions of industrial minerals to biotechnical products, but they represent a very large and rapidly growing new field of uses. The new biotechnology has nearly 300 small companies, plus 15 established companies with 742 biotechnology-related firms (Dibner, 1991b). Revenues exceeded $2 billion in 1990 and are expected to grow to $50 billion by 2000 (Anon., 1992c), with worldwide sales exceeding $100 billion (Burrill and Roberts, 1992). Federal research amounted to $3.4 billion in 1990 (Anon., 1992b). The United States is the world leader in biotechnology, but other countries have large, well-funded programs. Despite debate about safety, obstacles to new biotechnology products are declining (Embers, 1992, Gibbons, 1991). Fifteen biotechnology drugs valued at $1.2 billion (Thayer, 1991a) are on the market, and more than 100 are in various stages of testing (Edington, 1992). Many diagnostic tests are also in use or development (Demain, 1983, Anon., 1992). Large scale efforts to produce or transform important chemicals are also underway (Ng et al., 1983, Hinman, 1991), and research into geologic uses of biotechnology has begun. Much has been published about microbial mining, oil recovery, desulfurization, bioremediation, and other geologic aspects of biotechnology, but this chapter is the first attempt to explore interactions of biotechnology and industrial minerals. This chapter examines uses of minerals in biotechnology; how biotechnology can be used to discover, recover, and beneficiate industrial minerals; and speculates on some potential, but as yet untried uses. Definitions What exactly does the word biotechnology mean? Bud (1989) states that the first use of the term was by Karl Ereky in 1919 to cover the interaction of biology and technology, and in 1933 the term was used in Nature. After citing seven different definitions, Smith (1988) concludes that biotechnology is a series of enabling technologies involving practical applications of organisms or their subcellular components to manufacturing and service industries or to environmental management. Walker and Cox (1988) suggest a definition of "the practical applications of biological systems to the manufacturing and service industries and to the management of the environment." Primrose (1991) says that it is "the commercial exploitation of living organisms or their components." There is essentially an older broad use of the term and a new use. The US Office of Technology Assessment (Anon., 1984) uses a broad definition that includes any technique that uses living organisms (or parts of organisms) to make or modify products, to improve plants or animals, or to develop micro-organisms for specific uses. Definitions are different, but they all have several fundamental elements that include the control, management, or manipulation of living things for commercial, industrial, or useful ends. While such a definition encompasses all of agriculture in practice the "new" biotechnology is restricted to processes involving microorganisms-plant and animal cells, or enzymes. Many consider biotechnology to be recent, but it is one of our oldest technologies as evidenced by the prehistoric origin of brewing, cheese-making, and other techniques. [Table 1] gives some of the important developments in the history of biotechnology. Smith (1988) breaks down historical developments of biotechnology into four phases: 1) prehistoric with no understanding of underlying processes; 2) nonsterile processes; 3) sterile processes after 1940; and 4) genetic and recombinant DNA technology deliberate design of special organisms or processes.

Jan 1, 1994

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By F. Dingwu

The demand of manufacturing high-purity magnetite concentrate leads to the advent of various magnetic separators. A novel magnetic drum separator has been developed with an optimal permanent magnet system and a complex-forces field is adopted, involving magnetic force, gravitation, fluid resistance, friction, inertial centrifugal force, etc. Proper ultrasonic probes are inserted into the bottom tank to break up the magnetic floes. The performance of magnetite in the complex-forces field is described and the optimal operation conditions are suggested.

Jan 1, 1995

By A. R. Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Nines Camchib Inc. It is characterized by very fine first generation gold and very coarse second generation electrum. Successful processing required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented.

Jan 1, 1989

By E. G. Loesche

Grinding mills in which the comminution takes place between rollers and the surface of a disc, table or ring are generally known as roller type mills. The Loesche Mill, also known as the Disc Roll Mill, is a special type of roller mill in which the grinding surfaces consist of two rollers assembled over a horizontal disc or table which rotates at a relatively low speed. This design is particularly applicable to industry's present day demand for large capacity grinding mills.

Jan 1, 1964

By Thomas J. Ferree

The efficiency of Carbon-in-Pulp and Carbon­in-Leach circuits is determined by the degree to which the carbon can extract the gold from the slurry and transport it to the stripping circuit. The 'pick-up' efficiency of the carbon particles is affected by several factors which include the following: * The concentration of the carbon in the slurry. * The surface area of the carbon particles. * The reactivity characteristics of the carbon particles. * The retention time of the carbon in the slurry.

Jan 1, 1992

By Ian Mcgaffin

P.T. Kellan Equatorial Mining (KEM) is an Indonesian incorporated company owned 90% by CRA Limited of Australia and 10% by PT. Harita Jayaraya of Indonesia. The Kelian gold mine first commenced production in January 1992 and has produced in excess of 21 tonne of gold (675,000 oz) in its first 18 months of operation. The operation is a large tonnage low grade deposit that accepts a low gold recovery by industry standards due to the partially refractory nature of the orebody.

Jan 1, 1993

By D. Nilsson

This paper demonstrates the importance of including a discount rate in the determination of the optimum final depth of an open pit. Without a proper discount rate, a pit will probably end up too deep. Another consideration is future underground mining. If underground mining is profitable, the pit may need to be shallower. Of all of the investments needed, only mining equipment and the underground mine should be included, and amortization and depreciation should not he included in the study.

Jan 1, 1998

By M. Mohammed, S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of the shaft, stopes and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate. In this study, the finite element method (ANSYS) has been used with optimization criteria to design safer, more stable underground openings.

Jan 1, 1995

By Thomas S. Kovach

In today's competitive energy market, every effort must be made to assure the lowest possible production cost. 'rhi s. paper describes the cooperative effort between the coal producer and the utility customer to develop and install a fully integrated mine information management system at a 2.5 million tpy lignite mine in east Texas. A description of each item of the modules is included along with the problems encountered during development and how they were corrected. The system configuration is also described.

Jan 1, 1989

By F. Seymour

A dynamic programming algorithm is presented that takes a series of nested phases, a fixed mining-rate schedule and a fixed plant-production-capacity schedule, and, from these, finds the mining and cutoff grade sequence that maximizes the net present value. This tool allows the mining engineer to quickly look at project sensitivity to various production capacities, commodity prices and costs. A description of the algorithm is given along with examples of how it has been used at Newmont Gold.

Jan 1, 1996

By David W. Lillie, Pier A. Abetti

This paper reports on a study of the impact of fast growing new technologies on the market for copper over the next 15 to 20 years. The greatest threat is clearly the inroads of fiber optics on the traditional market for copper in communication cable. Opportunity areas identified include heat pumps, solar power and heat, desalination, electric vehicles and others. The overall impact of new technologies on copper is expected to be modestly positive if adequately encouraged by effective R&D.

Jan 1, 1986

By D. C. Panigrahi

The paper presents the development of a thermodynamic based network analysis model. It uses transient heat flow algorithm for computing the heat flow from strata and predicts the environmental condition in different branches of the network. Along with the environmental condition, the mass flow distribution in network is computed by using nodal pressure method based on linear theory approach. The algorithm has been coded using object oriented programming approach and it has been validated in actual field condition. The correlation is satisfactory.

Jan 1, 1997

By J. Yordan, J. Zinterer

Effective removal of ink particles by froth flotation is of up-most importance in paper recycling. In this study, the potential use of talc particles as carriers of difficult-to-float fine ink particles is investigated. In order to accomplish ink particles removal, the interactions between talc and oily- ink particles in aqueous solutions containing flotation chemicals was studied by zeta potential distribution measurements and with the impinging jet apparatus. The chemical conditions under which talc-ink adhesion occurs are identified and reported.

Jan 1, 2003