Search Documents

By A. M. Stone

INTRODUCTION In ore beneficiation one of the simplest methods of mineral concentration is hand picking to remove either the ore or the waste material from a moving table or conveyor belt. Ore Sorting Equipment may be defined as equipment for mechanized picking. This type of equipment has been used successfully over the past thirty years or so to beneficiate ores of various types in particle mesh sizes between 1mm and 200mm.. at throughputs of up to 150 tonnes per hour. In general for ore sorting to be a consideration the ore and the waste material must be well liberated in the feed to the sorter (that is into practically discrete particles of ore and waste). The larger the liberation size the more likely sorting is to be cost effective. Correct selection of ore sorting equipment is most important and often special machine features are developed for an individual application. Sorter performance can be best determined by extensive testwork of representative ore at design tonnage on prototype or preferably on production model sorting machines. ADVANTAGES OF SORTING ORE The four main advantages of sorting ore are: Reduced milling cost. Reduced processing cost. Higher overall recovery. Reduced transportation costs. Reduced Milling Cost With sorters installed the milling plant following the sorter is generally smaller and hence less costly to install and operate as it only has to handle the sorter product. However this benefit is somewhat offset by the increased cost of the screening and washing plant prior to the sorter and the cost of the sorting plant itself. Reduced Processing Cost As there is less material of higher grade presented to the concentrating plant following the sorter, this plant will generally be smaller and less costly to construct and operate than a plant treating the total quantity of material. Higher Overall Recovery The economic recovery is often misunderstood by plant operators when evaluating the advantages of sorters

Jan 1, 1986

By J. A. Finch

The photographic measurement of bubble diameter is tedious and restricted to vessels with transparent walls and relatively low bubble concentrations. A new method for predicting bubble diameter in a flotation column has been developed and confirmed by comparison with measured mean bubble diameter (Yianatos et al., 1987) Flotation columns are not mechanically agitated. This note describes an extension of Ms method to a mechanically agitated flotation machine. A recent publication by Szatkowski (1987) provided sufficient data to calculate bubble diameter by the proposed method and compare with values determined photo- graphically. Method In a two-phase system (gas and liquid), bubble diameter (db), superficial gas rate (Vg) and liquid rate (Vl), and gas holdup (Eg) are linked by two relationships (see the nomenclature at the end of the paper for definitions of symbols). [ ] Equation 1 is the definition of slip velocity (relative gas to liquid velocity) for a countercurrent gas-liquid system, and equation 2 is an adaptation (Yianatos et al., 1987) of the expression of Masliyah (1979) for hindered settling in a multispecies system. The solution for bubble diameter is by repetitive substitution of estimates of db in equation 2 until the calculated Ubs is equal to the measured Ubs in equation 1. Results and discussion Table 1 presents the data obtained by Szatkowski (1987) from a mechanically agitated laboratory flotation machine. The machine generated bubbles by directing a gas stream into the vicinity of a disk rotating at Ngh speed (up to 8000 rpm) in the flotation slurry. The air was completely dispersed in a swarm of fine bubbles. A photographic technique was used to determine the distribution of bubble size. The mean diameter and standard deviation were then calculated. Table 1 provides all the information necessary for computing bubble diameter (Vl is assumed zero). The calculated bubble diameter is presented in Table 1 as d;. Figure 1 plots measured versus calculated bubble diameter and shows reasonable agreement between values. There is an apparent tendency to undercalculate the small bubbles and overcalculate the large ones.

Jan 1, 1987

By A. W. Khair, S. S. Peng

Background The mine is located in Ebensburg, Cambria County, PA. Cambria County is located within the Allegheny Mountain section of the Appalachian Plateau Province. The geologic structures in the mine area included folds, faults, joints and cleats in the coal. These geologic structures seem to have genetic relationships with the Allegheny Front (lannacchione and Puglio, 1979). The mine's geologic structures have been influenced mainly by Ebensburg Anticline and Wilmore Syncline (Watson, 1979). Current longwall panels lay along the western limb of the Wilmore Syncline oriented south 30° west. Surface topographic relief in the area is less than 152 m (500 ft) and overburden thickness varies from 183 to 244 m (600 ft to 800 ft). The coal seam in the mine is part of the Lower Kittanning Formation. The thickness of the B-seam is the subject of discussion. It varies from 1.2 to 1.5 m (48 to 60 in.) and consists of two parts. The lower part is 1.1 to 1.2 m (44 to 48 in.) of soft coal and the remainder is bony coal. The coal seam dips slightly from 0° to 6° to the east-south direction. Panel entries are driven 61 m (200 ft) wide, consisting of three 5.5 m (18 ft) wide entries and two pillars 24.4 x 30.5 m (80 x 100 ft) centers. The mine has a history of cutter roof problems in the entries (Fig. 1) that has delayed the advance rate of entry development considerably and the cost of maintaining those entries is very high due to the requirement of very heavy artificial supports (Fig. 2). Due to excessive convergence in the headgate, installation of additional support and often resetting of steel beam, to provide enough clearance, in these entries imposed additional delay during the retreat of the longwall face, as the shearer cuts coal adjacent to the headgate and shield support at the headgate needs to advance under the steel beams (Fig. 3). Methodology Extensive underground observation indicated that roof cutter [ ]

Jan 1, 1992

By Hassan El-Shall, G. L. Zucker, T. S. Jordan

INTRODUCTION This chapter will discuss, both from fundamental and practical points of view, the flotation of non-sulfide min- eral s. The flotation characteristics of silicates, salt-type minerals, oxides and coal will be reviewed. Dup- lication of the thorough and excellent presentations by many authors is not intended and a comprehensive list of references is included. GENERAL PRINCIPLES Collectors for Non-Sulfide Minerals : All minerals, with only a few exceptions are readily wetted by water, that is, they are said to be hydrophilic. The purpose of a collector is to coat the mineral surface and render it hydrophobic, preferring an environment of air over an environment of water. Relative to sulphide minerals, the non- sulfides are more naturally hydrophilic and therefore, require a collector with a greater chain length. This is accomplished by using a collector which has a proportionally longer hydrocarbon chain. Both anionic and cationic flotation collectors are used in non- sulfide flotation. Anionic Collectors. These are collectors which ionize in solution to give a negatively charged radical. They have the general structure R-A, where R is a hydrocarbon having 8 or more carbon atoms and A is a hydrogen or an alkali metal. The most common collectors in this group are fatty acids which could have saturated or unsaturated hydrocarbon chains. Such chains may be straight or branched. The configuration of the chains affects their solubility in water and their adsorption characteristics. In general, as the chain length increases the adsorption and the collecting power increases. However, it should be noted that the solubility decreases. The solubility of unsaturated chains is greater than that of saturated fatty acids because double or triple bonds are polar and thus attract water molecules. Solubility data for collector metal salts, even though important for a proper understanding of flotation are not available for all collector systems. Solubilities and structures of different fatty acids are reported by Fuerstenau (1982). Values for the solubility products of fatty acid salts selected from a paper by Du Rietz (1958) are given in Table 1.

Jan 1, 1986

By L. Alan Weakly

The Powder River Basin is the largest strippable reserve of compliant coal in the United States. It is the mother lode, for this Basin is currently supplying 25 percent of the coal produced in the US annually. This paper updates what has happened in the Basin since 1993 in terms of increased production, higher productivity, changes in mine ownership, safety statistics, new equipment, latest coal technologies, and electrical deregulation ramifications.

Jan 1, 1998

By Z. Hladysz

It is common to nine a coal seam affected by previous extraction of a coal seam below. As a result of that severe problems may occur during the extraction process. This paper presents the analysis of undermining effects based on field observations. A simplified method for the evaluation of risk in undermining operations is presented and predictions of the degree of possible damages to the undermined coal seam is given.

Jan 1, 1985

By James Douglas

For the past several years, inflation has placed increasing pressure on our economic system. The total effect of inflation is complex when combined with other factors which affect the economics of equipment. A mathematical model is described herein which can be programmed on a computer to determine the effect of inflation on economic life and profits after taxes. The computer output results in graphic plots which clearly show the relation of various percentages of inflation to life and profits. Inflation has become a common topic of conversation in the recent past. What is it and how can it be measured? What effect does increased inflation have on equipment policy? Research now in progress at the Construction Institute at Stanford University is beginning to unravel some of the mystery of inflation. As a start, let us answer the first question by defining the word inflation. The dictionary says that inflation is "an increase in the volume of money and credit relative to available goods resulting in a substantial and continuing rise in the general price level. It appears, in fact, that we are in an inflationary spiral which is "a continuous rise in prices that is sustained by the tendency of wage increases and cost increases to act on each other." 3 Inflation behaves just like compound interest. It takes more dollars of future years to buy an equal amount of a given commodity, be it a material or a service. Let us assume an annual inflation rate of 5 percent. Assume that 1Associate Professor of Civil Engineering, Stanford University, Stanford, California. 2Webster's Seventh New Collegiate Dictionary, Springfield, Mass., G. and C. Merriam Co., 1969. 3Ibid.

Jan 1, 1972

By Benjamin C. B. Hsieh

Many processes in the hydrometallurgical and chemical industries require the separation of dissolved material from suspended solids. Counter current decantation (CCD) with thickeners is one of the methods generally used. The process engineer needs a quick and accurate CCD calculation method. Several theoretical 1-12 CCD calculation methods are available in the literature . The simultaneous 1, 2 equation method for a complex circuit as used would take too long to solve the problems. Approximate equation method1 is not accurate and is for simple cases only. A shortcut method developed by Counselman3 contains no mathematical equation, and thus is not suitable for computer programming. Based on Counselman's method, Woody4 derived two simple equations in terms of percent soluble loss for two typical examples. Scandrett5 included a term for mixing in his formulas. This mixing efficiency was defined by Murphree6. Another method which depends on making volume calculations instead of using weights is presented by Mastin8 and Cahalan9. None of these methods is related to dissolution and pre¬cipitation reactions. Chen 10,11 demonstrated his methods for counter current leaching. His results are calculated from the general solution of a derived linear difference equation for constant underflow, and from the solution of a derived non-linear Ricatti difference equation for variable underflow. This paper concerns derivation of a general equation for CCD washing with provisions for adding and withdrawing the streams, and for leaching (dissolution) or precipitation reactions. These equations take several forms depending on the input information available. A set of simplified equations for continuous counter current washing and leaching is derived for determining:

Jan 1, 1972

By Jerry Solomon

The subjects to be examined in my portion of the session entitled "Technology of Aluminum.. Recovery" will be twofold. 1. Economics of the basic aluminum economy--supply-demand-price. 2. Specifications of aluminum products produced from municipal waste--from the secondary aluminum standpoint. It is the object of this speech to first impress everyone with the excellent long-run markets for the aluminum products from municipal waste and then to acquaint everyone with the rather liberal scrap specifications that the recycling industry can tolerate. The most important statement that can be made about the recycling of aluminum is that it is now and will be an economic necessity. This is true far many reasons; one which hit the headlines recently was Interior Secretary Rogers Morton's statement "Third-world nations could use mineral wealth not to achieve political ends but to jack up economic positions. The result could be sky-rocketing prices and dwindling supplies on world markets." There is no reason why the group of countries that supplies most of our bauxite can't get together the way oil-producing countries got together on the price of oil. (Jamaica and Surinam, are original sources of two-thirds of the aluminum used in the United States.) The worry is not so much that we will end up without the basic raw material but rather that the price might be so high that we could not afford it. So much for the blackmail reason for recycling aluminum; the supply and demand picture in both the primary and recycling sectors of the aluminum economy is far more meaningful.

Jan 1, 1974

By John Bley

White Pine Copper Company operates a mine in the Upper Peninsula of Michigan using a modified room-and-pillar system for extracting ore.1 Mine production averages 15, 500 tons per day. The terrain is predominantly level and the depth of cover varies from 500 to 800 feet over the present workings with depth increasing as mining progresses down the dip. The deposit is situated on a low angle plunging, anticlinal structure composed of sedimentary beds. Local terminology for the stratigraphic units which contain the ore horizons, named in ascending order, is as follows: lower sandstone, parting shale, upper sandstone and upper shale. The ore zones of copper enrichment are, contained in the parting and upper shales. The parting shale will vary; from 6. 5 to 9.0 feet thick; the upper sandstone from 2 to 10 feet; and the upper shale from 1. 5 to 6. 5 feet. Two variation of the room-and-pillar system are used to extract the ore depending on grade and local ground conditions. One system is called the parting shale method and recovers the parting shale only. This system requires a mining height of 8 1/2 feet to accommodate large-scale, high-capacity equipment and this working height is obtained by removing approximately 1 to 2 feet of the barren lower sandstone with the ore. Under the second system, locally termed full column, the mining height is about 14-1/2 feet and this system removes the parting shale, the upper sandstone and the lower mineralized zone, approximately 1-1/2 feet, of the upper shale at which point it is possible to maintain a competent back (Fig. 1).1

Jan 1, 1964

By A. S. Kane

According to the 1966 Bureau of Mines Mineral Year Book only three states reported production of lignite in that year. These state: were North Dakota, Montana, and South Dakota; although it is known that there is production of lignite in Texas, California and, perhaps, Arkansas. In the year 1966 North Dakota produced 3,543,000 tons of lignite, Montana produced 328,000 tons of lignite, and South Dakota produced 10,000 tons of lignite. In view of the fact that North Dakota produces approximately 95 per cent of all the lignite reported in the United States, in discussing lignite mining, my remarks will be confined to lignite mining as conducted in North Dakota and will be confined to the production of lignite by stripping methods, as this is the predominate method used today. The first lignite mining in Worth Dakota, undoubtedly, was done by people settling in the western part of the state where wood was scarce and where lignite is exposed in the banks of creeks and ravines. The first production records were kept in 1884 and indicate that 35,000 tons of lignite were mined that year. The growth of the lignite industry has been very slow during the intervening period, but in 1966 production started to increase, and it is now indicated that production in the next few years may approach 6,000,000 tons per year. Ninety-seven per cent of the lignite produced in the lignite area of the Midwest is utilized in the generation of electric power, and it is anticipated that this use will predominate during the next two decades.

Jan 1, 1968

By C. D. Atkinson

The past few years have seen a much greater concern about air pollution in this country. This concern has led to increased legislation restricting the discharge of many substances such as sulfur dioxide and particulate matter to the atmosphere. In the future, it is anticipated the present permissible emission levels will be lowered. Current and impending restrictions on the emission of sulfur dioxide have brought out the fact that there is a shortage of available low-sulfur fuel for power plants and industrial use which promises to have an economic impact on the nation's energy picture (1) The Pittsburg & Midway Coal Mining Co., under the sponsorship of the Office of Coal Research, has developed a process to produce a fuel capable of meeting the energy requirements of this nation (2) The process is called "The Pittsburg & Midway Solvent Refined Coal Process". The principle product from the process is Solvent Refined Coal which is an ashless, low-sulfur fuel with 16,000 BTU per pound regardless of the rank coal from which it is produced. The product can be burned as either a solid or a liquid fuel. The process appears to be economically more attractive than other methods of alleviating the pollution problems of this nation. In addition to reducing the air pollution caused by stack gases, the product produced is potentially useful as a source of electrode coke and electrode binder pitch, as a gas turbine fuel, in the production of metallurigical coke and pavement asphalt, and as the first step in the overall process to produce distillate fuels and pipeline gas (3).

Jan 1, 1973

By A. M. Gaudin

The recent study by R. M. Hays(l) prompted the study summarized in this paper. In his Interesting paper, Mr. Hays shows fine results to be attainable by a relatively complex flowsheet on a semi-taconite, a manifestly difficult ore to treat. We obtained a semi -taconite from Minnesota, and treated this sample by wet magnetic separation alone. The device in which the separation was accomplished is the standard pilot-plant, laboratory separator in use at Magnetic Engineering Associates' laboratory (MEA) in Cambridge, Massachusetts. It consists of a cylindrical space which can be magnetized by turning on the magnet of the separator. In this cylindrical space, there is a canister which provides the special configuration of the magnetic field and magnetic field gradients that MEA considers to be required. The ore pulp is made to flow through the canister while the current is on. A portion of the pulp is retained in the canister, and the rest is evolved as a non-magnetic fraction. The laboratory device is cyclic, but it accurately predicts the results obtainable by an Industrial unit of either cyclic or continuous type (moving matrix). The ore tested was 99.5°%o -325 mesh, and approximately 75% -500 mesh. The concentrate from this ore was, therefore, eminently suitable for pelletizing. In passing the ore through the magnet, we had the choice of repeatedly passing the concentrate from the first step through the operation, or of repeatedly passing the non-magnetics. In our experiments, the first method was clearly superior from the stand¬point of the cleanliness of concentrate. Of the many tests which we have made, we think that we have to retain two which

Jan 1, 1971

By I. J. Dowdeswell

Perspective Man is a model maker. Throughout recorded history man has-used models both to provide insights into the workings of the processes which surround him and as a step towards the eventual control of those processes. These models have covered the field from extremely large systems (solar and celestial. models) to infinitesimally small systems (sub-atomic .and atomic models). Models have been developed for social systems, ecological systems, biological systems and economic systems: all fields of human endeavour contain the fruits of this restless model-making. The Role of Models Since the evidence of mans' industry in formulating models is so abundant, it is worthwhile stating some of the reasons. Based on the simple definition that "a model is a convenient and useful representation of some facet of the 'real' world", then a model provides a means for: 1. Understanding the thing being studied. 2. Communicating that understanding to others. 3. Manipulating the thing being modelled. The common denominator implicit in these reasons is that- improved control is the. objective off all modelling or simulation work. Improved control shows itself either directly by the development of devices which perform the control functions or indirectly by improvement in the decision making process itself. For example, in a process plant, a suitable model of part of the process could lead either to the use of automatic control devices such as set-point controllers or to the implementation of instructions (pre-defined decisions) which permit the operator to better control the process. Typical process control systems use both of these since fully automatic control is restricted to processes where the required information can be effectively measured.

Jan 1, 1972

By James A. Clum

The shift to lower grade iron ores, e.g., magnetic taconites, resulted in a shift towards agglomeration practices which could effectively deal with the fine particle sizes generated in the liberation and concentration processes. If the iron bearing particles are not extremely fine, e.g., -1/2 in + 100 mesh, sintering is an adequate means of agglomeration.(1) For the more dispersed ores which result in fine concentrates (more than 80%,-325 mesh), the fine particles must be agglomerated by mechanical means before final hardening, e.g., pelletizing.(1) In the pelletizing process, the essentially mechanical step of balling is extremely critical since the strength of the pre-fired pellet determines the firing conditions. The ability of the proper amount of moisture to hold together a ball of the very fine ore concentrate particles has long been recognized. It is a charac¬teristic of the reaction at the interface between the ionic solid of the ore concentrate and the polar water phase which overlays the solids. The strength in such moisture laden balls, the green strength, is a strong function of the water content (Figure 1) and thus deteriorates rapidly for either a small excess or a small deficiency of moisture. For purposes of commercial practice, the control of green ball handling properties by accurate control of ball moisture is too demanding. Moreover, as the ball is heated towards its hardening tempera¬ture, e.g., 1300'C, there is a substantial drying reaction which would lead to such a low dry strength of the ball that it would not support its own weight much less the weight of other balls in a firing furnace.

Jan 1, 1976

By J. C. Irvine

Meramec Mining Company is a joint venture by Bethlehem Steel Corp. and St. Joe Minerals Corp. which mines and pelletizes iron ore at the Pea Ridge Mine. The Pea Ridge property is located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during a lead exploration program. The first test holes drilled on the Pea Ridge magnetic anomaly revealed the presence of a large magnetite deposit; further drilling in 1956 and 1957 confirmed that the orebody was mineable, Meramec Mining Co. was incorporated in 1957 and shaft sinking began late in the year. Production commenced in April 1964. The orebody is overlain by about 1300 feet of flat-bedded sediments. It is tabular, about 2600 feet long and up to 600 feet thick. It dips about 80° and is of unknown depth. The ore is mainly high grade magnetite with small zones of specular hematite. The wall rock is a Precambrian rhyolite porphyry. The mine was initially started with five major levels on 150 foot intervals. Crosscuts were driven across the orebody on 190 foot centers. Banks of scopes were mined between the crosscuts by a modified shrinkage stoping method. This was done by undercutting a 40 foot wide by 150 foot long block and blasting horizontal "lifts" drilled on 5 foot intervals. A 65 foot still was left between levels which contained the slushing drift, fingers, crown pillar, and adequate thickness for support. By 1971 a ?lattice? of pillars had been left and mining had progressed to the point that an orderly pillar recovery program was necessary.

Jan 1, 1976

By Ronald E. Heuer

The significance of surface settlement over soft ground tunnels is well recognized. Cracked buildings, streets transformed into lakes, broken utility lines, to underpin or not to underpin--all are familiar problems. The basic causes of surface settlement are recognized. Possibly the most common and troublesome cause is "lost ground" during construction. Lost ground refers to removal of a larger volume of ground (Ve) than is eventually occupied by the final tunnel structure (Vt). A number of sources of lost ground in shield tunneling have been identified, as illustrated in Fig. 1. These include 1) face loss, 2) overcutting loss, 3) annular tail void loss, and 4) loss through the lining. The ground generally does not stand unsupported around the completed tunnel lining as illustrated in Fig. 1, but moves in to fill the lost volume, resulting in subsidence of the overlying ground surface as shown. As suggested in Fig. 1, lost ground and surface settlement associated with overcutting and the annular tail void tend to occur systematically along the tunnel length. This "systematic" lost volume is "limited" in the sense that it is restricted to an upper limit determined by the shield and lining geometry. Partially controlled face loss may sometimes contribute to this systematic loss. This lost volume is commonly a few percent of the nominal tunnel volume. The resulting surface settlement over the tunnel is commonly in the range of a few inches or less and develops over a period of hours to days. Although they may have a significant impact on surface facilities, systematic ground loss and settlement frequently have little adverse effect on tunneling progress.

Jan 1, 1976

By F. Mensah-Dwumah, W. H. Baker, G. W. Clough

INTRODUCTION The practice of injecting chemical grouts into permeable soils in order to stabilize them for tunnel construction is a common procedure in Great Britain, Europe and Japan. In this technique, the grout penetrates the soil in a fluid condition, but hardens or "sets-up" in about one hour due to a chemical reaction. As a result, the soil, is strengthened and made less pervious, and this, in turn, reduces ground surface movements, limits ground water flow, and controls movements of the heading during tunnel construction. It is only within the last five years or so that this technology has been used in the United States. Most of the applications have been involved in the work for the Washington Metropolitan Area Transit Authority (WMATA) subway construction. The experience gained from this work is, in many instances, unique and should serve to guide use of the grouting technology in future projects. This paper documents five WMATA case histories; information is provided as to the soil conditions, method of treatment, reason for treatment, and tunnel performance. Locations of the five projects covered by this study are indicated in Figure 1. All are within the boundaries of the District of Columbia and involve soft ground tunnel construction. Basic information for the case histories is given in Table 1. Tunnel sizes and depths below the ground surface as well as general soil conditions are similar in all instances. The tunnels are about six meters in diameter and are located so that the crown is five to ten m below the ground surface. The soils typically consist of alternating sand, clay and silty sand strata. However, soil stratification details are

Jan 1, 1979

By Murray D. Lester

The relationship between bauxite and energy has two distinct aspects. On the one hand, since virtually all of the bauxite that is mined winds up as aluminum metal, the economic health and future of the bauxite industry and of the bauxite-producing countries depend on the continuing vigour and competitiveness of aluminum against alternative metals and materials. The price of aluminum is, in turn, particularly dependent on the price of energy. Hence, the need for bauxite is ultimately affected by the price of energy. The second aspect relates to location of the bauxite industry. There is no shortage of bauxite resources in the world. For various reasons, as we shall see, there is a growing tendency toward the integration of bauxite mining, bauxite refining and aluminum smelting in those countries that have the resources both of bauxite and of energy necessary to support the entire production chain. Thus, the availability of attractive energy supplies will increasingly favour development of bauxite mining: the traditional export of bauxite as a simple raw material is likely to diminish in relative terms. In short, both the amount of bauxite mined and where this mining will take place are related to energy considerations. Let us first have a brief look at the four basic activities that are involved in our integrated operations: A. The bauxite is mined and moved to an ore plant. This step does not require more than relatively modest amounts of energy normally associated with excavation, loading and shipping of any bulk material. We need about four or five tonnes of bauxite for every tonne of metal produced.

Jan 1, 1984

By Ian McFeat-Smith, Robert J. Fowell

Roadheader machines have a specific place in modern tunnelling, not simply as a compromise between drill and blast techniques and full face machines, but as an economic and versatile form of mechanised tunnelling where the method of excavation is easily integrated with tunnelling operations. In the past, roadheaders have been subjected to misuses by engineers who failed to realise that, as in all mechanised tunnelling, a planned and systematic approach is essential if the full potential of these machines is to be gained. An increasing awareness of this, together with the introduction of the more powerful roadheader carrying their cutting potential into the hard range of rock is changing this situation and now makes the prospect of using roadheaders particularly attractive (1). The advantages gained by employing these machines can be considerable and Table 1 lists some of them. This table illustrates that from both cost, and installation points of view, the roadheader has considerable benefits over the full face machine. However, the principal advantage gained is in broken ground where heavy supports can be installed immediately at the tunnel face. In addition, access for planned maintenance and repairs to most working parts of the machine is at a premium and average machine utilisations of 40 - 60% can be expected. In comparison to drill and blast methods, up to 40% better progress can be regularly achieved, and the subsequent savings in overbreak costs alone would more than pay for the cost of a roadheader used to drive a 3km long tunnel. As with full face machines, ground disturbance is minimal and for short tunnels in urban areas a road-

Jan 1, 1979