Search Documents

By John M. Hird

Texasgu1f's Lee Creek Mine in Eastern North Carolina is usin8 a combination Dredge-Dragline method for mining deep phosphate ore at a rate of 8.5 million tons per year. The matrix is thick, uniform in grade, and is processed into agricultural products. As in many other good mineral deposits, there are tough obstacles to overcome in recovering the ore. The deposit is in an area with a land surface of about ten feet above sea level, is close to tidewater, is overlain with 90 to 130 feet of unconsolidated overburden, and is underlain by an artesian aquifer with over 140 feet of natural hydrostatic head at the bottom of the bed, The upper 40 feet of overburden will not support stripping equipment and is unstable when cast as spoil. Barriers are emplaced to prevent flooding from hurricane tides. The ground water problems have been successfully controlled by pumping 60 million gallons per day from the aquifer. Only recently have the severe ground problems been overcome by this unusual Dredge-Dragline combination of mining equipment.

Jan 1, 1978

By G. P. Richards

RIP is the process of recovering uranium from an unclarified slime pulp which comes in contact with a moving bed of ion exchange resin, T e sand-slime separation of the acid-leach slurry is accomplished through the use of cyclones and spiral, akins type classifiers. Course sands are discarded to tailings and the combined slimes and leach liquor become the IX feed. Uranium in the IX feed is absorbed on the resin and after exhaustion the barren pulp is directed to tails, Following the uranium exhaustion cycle an eluant solution passes through the resin bed stripping the uranium from the beads, The uranium is precipitated from the clarified pregnant eluant, filtered, dried and packaged for shipment to the AEC, Normally, the ore received at the Mines Development plant is a loosely cemented sandstone containing small quantities of clay and bentonite, The ore is easily crushed and requires only a 1/3 load of rods in the rod mill to reduce the ore to grain size, Very little of the ore is recirculated by the 42" spiral classifier.

Jan 1, 1958

By Staff

GENERAL DESCRIPTION The Lucky Friday mine is located in Mullan, Sho-¬shone County, Idaho. The mining method is horizontal slice cut-and-fill (with timbering for support or un¬timbered) using hydraulic sand. Cemented sand fill at a 1:17 ratio is used in sill pours and at a 1:7 ratio for the final 152 mm (6 in.) capping in successive stope floor pours. Annual production with 100% cut-and-fill mining is 167 829 t (185,000 st). The average depth of mining is 1296 m (4250 ft) and the average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size The ore body is 396 to 488 m (1300 to 1600 ft) long on strike, 1421 m (4660 ft) on dip, with an average width of 2.3 m (7.5 ft). Dip varies from vertical to1.2 rad (70°) Ground Conditions, Ore Value, and Production Requirements The ore body contains quite strong argentiferous galena and quartz. The hanging wall and footwall are strongly sheared and fractured. Ore value is $211/t ($192/st).

Jan 1, 1982

By Don Rose

I. INTRODUCTION The Atlanta Research Chamber is an UMTA-sponsored applied research facility studying tunnel design, excavation and support systems. It is located directly below Peachtree Street in downtown Atlanta, Georgia. It is included in the CN-120 contract to build the Peachtree Center subway station, a part of the Metropolitan Atlanta Rapid Transit Authority (MARTA) multi-billion dollar "Phase A" 53-mile transit project, which is 80 percent funded by UMTA with 20 percent provided by local authorities in Atlanta and Fulton and DeKalb counties (Figure 1). The Research Chamber is located immediately south of the main Peachtree Center Station cavern, and is in part an enlargement of the pre-existing Pilot Tunnel excavated to provide bidders on the CN-120 contract a view of the rock conditions (Figure 2). The Research Chamber lies some 3 meters above, and is approximately parallel to, the twin Running Tunnels. The Research Chamber is 18 meters long and has the same 5.5 meter diameter horseshoe shape design dimensions as the twin Running Tunnels.

Jan 1, 1979

An atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) on arsenopyrite surface in solutions. AFM images show that the collectors adsorb on arsenopyrite surface in patches at pH 6. Increasing the chemical dosage will increase the adsorption density of the patches on mineral surface. The increased probe-arsenopyrite adhesion measured in PAX solutions at pH 6 is attributed to the adsorption of the patches, suggesting the hydrophobic nature of the patches, which is likely the oily dixanthogen. It is also found that arsenopyrite is reactive in water in the presence of air. At a high pH with the addition of Ca(OH)2 the adsorption of collectors on arsenopyrite is greatly retarded or depressed because the mineral surface is coated by a lot of precipitates, which is hydrophilic in nature as shown by the measured strong repulsive probe-arsenopyrite detachment force. The findings confirm that the flotation behavior of arsenopyrite in xanthate solutions is very similar to that of pyrite.

Feb 27, 2013

By Dan Nilsson

INTRODUCTION There are many mine planning factors in sublevel caving, as in the other mining systems, which when varied can substantially alter mining costs and profit¬ability. In this chapter, the following four topics are addressed with regard to economic optimization of sub¬level caving: production planning, haulage level spacing, orepass spacing, and extraction cutoff. The costs used here are the right order of magnitude but since each mine is unique, they should be considered only as examples. The objective is to demonstrate the tech¬niques which can be used. In a real mine, the evalua¬tions must be done using actual costs and conditions. It is difficult to predict exactly the costs involved, and therefore it is valuable to perform a sensitivity analysis to evaluate the effect of making incorrect as¬sumptions. Since the mining industry is very capital intensive, the effect of the interest rate must also be studied. PRODUCTION PLAN FOR AN IRON ORE DEPOSIT Introduction The first and most important thing to do before de¬signing an underground mine is to establish a long-range production plan. Such a plan is necessary for all eco¬nomic evaluations and should provide information about the lifetime of the mine, how much ore and waste must be handled per year, how much development per year is required, etc. An example is given in the following section. Problem In an iron ore mine sublevel caving is used. The iron content is 42%, and the mine supplies a pelletizing plant with an annual capacity of 3 million t/a. The ore body is shown in Fig. 1. The length of the ore body is 1000 m and the width is 100 m. Each slice is 10 m high, and there are 10 m be¬tween crosscuts, each of which has an area of 20 m2. The density of the ore is 3.5 t/m3. The spacing between rings is 2 m, and the extraction is 100%. The iron con¬tent is 66% in the pellets and 6% in the tailings. The problem is to develop a detailed production plan. A typical sublevel caving sequence is shown in Fig. 2. Solution Amount of ore per meter of crosscut: 20 X 3.5 = 70 t. Number of crosscuts per slice= 100. Length of crosscuts per slice: 100 X 100 = 10 000. Ore from crosscuts per slice = 10 000 m X 20 m2 X 3.5 = 700 000 t. Number of sublevel caving rounds per slice: 10 000/2 = 5000. Area for each blast in sublevel caving: 10 X 10 - 20 = 80 m2. Amount of ore per blast: 80 m2 X 6 m X 3.5 = 560 t. Extraction: 100% (see extraction curve Fig. 12). Loaded ore per blast: 75% or 420 t. Loaded waste per blast: 25% or 140 t. Total: 560 t. Total amount of rock from each blast in the sublevel caving: Ore: 560 t of which 2 X 70 = 140 t from develop¬ment work and 420 t from sublevel caving. Waste: 140 t. Total: 700 t. The ore needed per year is 3 X (66-6)/42-6 5 mil¬lion t. Necessary number of blasts per year= 5,000,000/ 560 = 8929. Distance to develop per year = 8929 blasts per year X 2 m per blast 17 858 m. Total amount/year: Ore from development work 17 858 m x 70 t/m = 1.25 million t/a Ore from sublevel caving: 8929 blasts per year X 420 tons per blast = 3.75 million t/a 5.00 million t/a Waste rock dilution: 8929 blasts per year X 140 tons per blast 1.25 million t/a Total amount to hoist 6.25 million t/ a The amount of ore from development work will in¬crease a little if the horizontal drift is placed in the ore body and not in the footwall. In this example the ore loss in 20%, and the waste rock dilution is also 20%. After taking the ore loss into account, the lifetime for 100 m of the ore body will be:

Jan 1, 1982

By Melvin A. Jennings

Even though the title of this paper is quite long, the ideas presented herein are very simple. In fact, it occurs to me to be somewhat humble about coming before such a distinguished group with such a simple presentation. However, the application of these ideas has proven useful in at least two copper flotation plants. The purpose in presenting this paper is to inspire some interest in the great stores of data chat the Mining Industry often accumulates without making any attempt at analysis. Unfortunately, many milling engineers rely rather heavily on percent recovery as a strict measure of a concentrator's relative performance. The fallacy of this reasoning is not difficult to see since, by definition, percent recovery is a function of feed assay, tails; and concentrate grade. If copper tailing is constant, and it very nearly is for a strictly sulfide copper ore, percent recovery must fluctuate almost directly to the feed assay. The point that I wish to make here is that it is very seldom justified to compare the percent recovery figure from one period of time to another without considering the difference in feed assay. The problem of comparing results is even further complicated when the ores are of mixed oxide and sulfide mineralogy.

Jan 1, 1978

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population. The Darling Plateau is old, having been formed some 200 million years ago, and its soils are deeply weathered. The parent materials were granite and gneis which have broken down to form lateritic gravels, overlying dense kaolinitic clays. Some 30 million years ago, in the Tertiary period, a sub - tropical climate prevailed. Appropriate conditions of moisture, temperature and drainage led to extensive laterisation. Some of the laterite contains bauxite of mineable quality. Some 1.9 million hectares of the south-west of Western Australia is covered by eucalypt forests. Threequarters of this forest is referred to as "Jarrah

Jan 1, 1984

By K. Holmberg, D. Herriot

This paper by Mr. McIvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulating load operation. The Bond calculation is itself based upon

Jan 1, 1990

By Thomas E. Browne

The Electric Power Research Institute Energy Supply Program is developing coal supply forecasts. By coal supply forecasts I mean the future relationships between coal price and production levels. A representative supply curve is shown in Figure l. It will make the rest of my presentation clearer if at this point I give you some background about EPRI and the Energy Supply Program. EPRI is funded by the nation's electric utility industry to develop new technologies for the production and conservation of electricity. Most of the research is conducted by outside contractors. We participate in joint projects with the Department of Energy and other organizations. The Energy Supply Program is one of three "economic" programs. The other two are Energy Demand and Conservation, and Systems. The Systems Program's main function is to provide the means to integrate the output of the other two Programs. The primary function of the "economic" programs is to provide information pertaining to future energy prices, availability, requirements, etc. to the EPRI personnel planning R&D programs. A secondary role that is becoming more and more important is providing information of direct use to the electric utility industry. I should note that the results of all EPRI's contract work are available to the general public. A "Coal Supply Analysis System" is being developed for EPRI by Charles River Associates. To the extent possible it will draw upon existing work, but much additional work needs to be done in the area of coal supply economics.

Jan 1, 1977

By Michael J. Taylor

Introduction A prime goal in the design and operation of uranium milling waste or tailing disposal systems is to mitigate adverse effects of tailing liquid on the adjacent groundwater. Adverse effects are often defined as modifying the groundwater quality in such a manner as to have detrimental health effects on downstream users. To accomplish this goal, the following three types of systems are employed with regard to the seepage and groundwater aspects of waste disposal: Type I Systems Seepage is allowed to occur unabated from the tailing disposal facility. Detrimental radionuclides and chemical elements are prevented from causing adverse downstream effects by natural purification actions in the subgrade geologic materials and the near zone groundwater. Monitoring is required to assure the predicted natural purification is occurring. The consequences of seepage loss is minimal since the m be predicted with current investigation and analytical techniques and can be evaluated as to effectiveness during operations. Type II Systems Seepage is partially retained in a waste impoundment or leakage from a designed retention system is anticipated. Natural purification is relied on for controlling migration of detrimental radionuclides or chemical elements, or contingency planning is employed to collect and return the tailing liquid to the impoundment. Installation efforts and concern for escape of tailing liquid are greater than for Type I systems, but extra precautions to preclude all seepage are not implemented. Monitoring is required to detect leakage and/or assure the natural purification of escaping tailing fluid. The consequence for accidential excusions are moderate, and will be excessive only if massive system failure occurs. Type III Systems Seepage is totally restricted by a costly system constructed and operated with extra care. Natural

Jan 1, 1980

By Darrell E. Young

This presentation will define what talc is, how it is mined and processed, and how talc is used in the paper industry. It will also give you some idea about who Luzenac America is and from where it came. Luzenac America was formed in July, 1992 as a result of the acquisition of the talc assets of Cyprus Minerals by RTZ of the United Kingdom. Cyprus Industrial Minerals was then merged with the other RTZ talc interests under the Luzenac name. Luzenac is a town in the Pyrenees of Southern France -and the home of Talc de Luzenac, RTZ's first talc acquisition. The Luzenac Group is the largest talc producer in the world.

Jan 1, 1993

By K. T. Cunningham

The Oakfield, New York Hine of the United States Gypsum Company is a shallow, room and pillar mine developed in the Camillus Formation of Silurian Age on the up-dip edge of the northern Appalachian Basin. The gypsum comes to subcrop beneath a variety of glacial materials and is subject to solution activity by groundwater. A geologic environment unfavorable to mining activity is thus created. Since 1978 seismic studies have been used to supplement core drilling to determine a conservative boundary between normal and questionable mining environments. A single channel seismograph, originally in use, is now replaced by a twelve-channel unit and is used to determine bulk material velocity which is the basis for defining the mining limit.

Jan 1, 1987

By Farlow C. Davis

Magma Copper Company, San Manuel Division, is a wholly owned subsidiary of the Newmont Mining Corporation and located at San Manuel, Arizona. The ore body is a dessiminated porphry copper deposit in quartz monzonite. The primary copper mineral is chalcopyrite with minor amounts of chalcocite, bornite, and covellite. The molybdenite occurs mainly on fracture faces or else associated with quartz veinlets. Pyrite is the major sulphide mineral in gangue. The feed to the concentrator from the underground mine is approximately 0.720 percent copper and 0.029 percent molybdenite. The concentrator has a design capacity of 62,000 tons of ore daily. After a standard ore treatment circuit consisting of grinding, rougher flotation, regrinding, and cleaning, a bulk concentrate is produced which contains 27 to 29 percent copper and 1.0 to 1.2 percent molybdenite. This concentrate is pumped to the molybdenite plant feed thickener.

Jan 1, 1977

Reclamation of surface mines is a crucial environmental issue and a key challenge to the worldwide mining industry. One of the goals of reclamation is to ensure that the area is left in a condition permitting safe future use. Hence, the reconstruction of open pits, waste piles and tailings dams must satisfy appropriate geotechnical stability and safety conditions for the planned use. Landscaping in the final stages is highly relevant as the topography around the mining areas is sometimes dramatically modified by ore extraction. The reclamation strategies must be applied not only after ore exhaustion, but also during its extraction. This is a sound business strategy that leads to considerable environmental benefits and increased security of the mining operations.

Jan 1, 2003

By Gordon H. Jardine

The cost of performing equipment maintenance is an increasingly significant component in the total operating cost of today's capital-intensive, large-scale mining operations. Because of the interdependence o f equipment maintenance on other functional areas of the minesite, an integrated approach to the monitoring and control of maintenance costs is essential. An important element of the introduction of computer-based systems in a mine is the acceptance of the systems by the users. The development history and major features of a minesite-developed system, which emphasises the user's importance, is described. The system outlined is designed to provide information for decision-making to the place where the company's maintenance money is actually spent - on the shop floor.

Jan 1, 1986

By Fathi Habashi

At the Duisburger Kupferhütte plant in Germany, pyrite cinder is collected from the sulfuric acid manufacturers in that country and processed to recover the nonferrous metals contained in the cinder, before charging it to the blast furnace for iron recovery. A typical analysis of the cinder is given in Table 9-1. The pyrite cinder is mixed with NaCl and treated continuously in a multiple hearth furnace. The evolved gases are scrubbed with water to form a weak acid which is used for the leaching process. Each batch requires about 2 days for leaching. The concentrated leaching solution obtained in the first 15 to 20 hr is sent for copper recovery, while that subsequently obtained, being poor ill metal content, is recycled. The residue, called purple ore, now a high-grade iron ore (61-63 % Fe); is sintered and delivered to the blast furnace.

Jan 1, 1970

By J. A. Pagliero, R. T. Quiroz, S. H. Castro

Selected voltammograms in tetraborate buffer solutions in the presence of ethyl xanthate or isopropyl xanthate at pH 9.3, for chalcocite, covellite, chalcopyrite, and enargite mineral electrodes, are presented. The concept of critical Eh of dixanthogen condensation (Ehc) is introduced, and the line of Ehc is thermodynamically defined in plots of log [X i] vs Eh, for methyl, ethyl, propyl, and butyl xanthates. A reaction scheme of xanthate oxidation in four steps, involving the dixanthogen condensation step, is proposed. A first attempt to interpret mineral flotation from a more general point of view is made. The electrochemical mechanism of dixanthogen formation and condensation is considered as a particular case of a more general and relevant phenomenon, which is the decomposition of the collector giving hydrophobic colloidal forms, whose associative behavior in bulk solution and at the mineral/solution interface is governed by colloid chemistry.

Jan 1, 1989

By Robert W. Bartlett

Pretreatment of sulfidic refractory gold ore by biooxidation in coarse-crushed ore heaps is a promising new technology, especially for low-grade ores that cannot afford pressure leaching or roasting. An algebraic equation for determining the economically optimum biooxidation of the sulfide minerals in the ore is provided that is based on the empirical biooxidation rate constant for the ore, the project's financial discount rate, the ore grades of both refractory and non-refractory gold, and the gold price. Then, the economically optimum duration of bioheap pretreatment, t$, is determined from its logarithmic relation to the optimum fractional extent of ore biooxidation, F$, through the ore's biooxidation rate constant. In doing so, it is assumed that the ore is adequately crushed and amenable to bioheap pretreatment and that the cumulative oxidation of the ore with time is known from ore testing so that the rate constant can be determined.

Jan 1, 1995

By H. Soto, G. Barbery

The effect of particle size on the flotation of coarse particles is analyzed. It is concluded that turbulence and the presence of the froth layer are detrimental to the recovery of coarse particles during conventional flotation. A counter-current column cell is proposed to avoid these two factors. In this column, a net upwards flow of water is prevalent, such that no froth is allowed to form on the top. Also, the levitation of heavy bubble-particle aggregates is helped by the ascending water current. Preliminary work at laboratory level with kilogram-size samples indicated that under similar conditions recoveries in the column were much higher than in conventional cells. Flotation results obtained with coarsely sized phosphate and quartz samples are presented. One interesting feature of this type of column is very fast flotation kinetics. Thus, a short column (only 55-cm collection zone) yielded, full recovery of floatable values.

Jan 1, 1992