Search Documents

Underground testing was carried out by Ingersoll-Rand, Inc., under contract to the Bureau of Mines to determine the effectiveness of a machine-mounted scrubber system for ventilating the face during an extended advance. A continuous miner equipped with an integral flooded-bed dust scrubber system was instrumented with methanometers and Real-time Aerosol Monitor (RAM) dust monitors. Methane and respirable dust data were collected at brattice setbacks of 7.5 m (current operating distance), 10.5 m, and 15 m (blowing ventilation) during production shifts. Results showed that a suitable machine-mounted scrubber system can adequately ventilate the face at brattice setbacks up to 15 m. No deterioration in ventilation performance was observed as brattice setbacks were increased from 7.5 m to 15 m. The scrubber system effectively controlled face methane levels at large setbacks, though respirable dust levels increased as much as 33 pct at the operator's cab at setbacks greater than 7.5 m.

Jan 1, 1986

By Robert H. Hooff

The Vor-Siv Dewatering and Classifying Unit was developed by the Polish Coal Industry because of a need for a unit that would dewater and classify high volumes of solids in water slurry. To be practical, the unit needed to be relatively small in size, simple in design, involve low operating costs, and be able to give a dewatered product of less than 30% moisture. The answer to the above mentioned criteria was the Vortex Dewatering Sieve or, as we refer to it, the Vor-Siv. The original installation of the unit, as we know it today, began in 1963 when the Pols installed the unit in a full scale pilot application. By 1966, at least 30 of these units were installed throughout the Polish Coal Industry. This equipment was originally introduced in the United States in 1966 at the Fifth International Coal Preparation Meeting in Pittsburgh, Pennsylvania. The first installation in the United States was not achieved until 1970, when Mr. Fred Sachs of The Valley Camp Coal Company, Triadelphia, West Virginia, installed a Vor-Siv in a retrofit application. To date, there are 36 Vor-Sivs installed in this country and 29 in the process of being installed or delivered.

Jan 1, 1976

By M. D. Ross

Complex combinations of technical, economical, safety and environmental factors are causing mining engineers everywhere to review their operations. Naturally, some of the traditional methods still have a large role to play because they are, in certain circumstances still adequate and are well understood. But, as circumstances change, a new approach is required. The combination of technical and economical reasons for introducing Long- wall mining in some seams in the United States is associated with strata control. Other reasons include simplifications and improvement of ventilation, reduced coal dust, more output from each unit and crew, increased percentage of recovery from each area of the coal deposit, and reduction of rock dusting. The innovations which transformed Longwall mining from a cyclic to a continuous mining system were the armored conveyor and power loading machines, but the crucial breakthrough for application to high production was the development of the powered roof support, which at once gave the system the advantages of mastery of strata control, increased rate of advance, significant reduction of manpower, and increased safety.

Jan 1, 1974

By W. J. Roberds

A formal and explicit yet cost-effective approach is proposed to ensure that decisions made during mine development are optimum (with respect to their ultimate consequences) as well as defensible. This risk management approach is based on probabilistic risk assessment and established decision analysis techniques, and appropriately considers the relationships among various mine development decisions, tradeoffs among consequences, the uncertainty in predicting consequences, and the benefits of flexibility to respond to changed conditions.

Jan 1, 1992

Conventional logging tools such as density, neutron, and acoustic have ranges of investigation of tens of centimeters. The borehole gravimeter, however, has a range up to hundreds of meters. For example, from the center of a cylindrical orebody 0.22 g/cm3 denser than its surroundings, one can detect the boundary of the orebody at a radius as large as five times its height. More complex structures can be investigated with computer programs. We can predict the usefulness of proposed gravity surveys, or decide which suggested structure is most likely to have caused the results of existing surveys.

Jan 1, 1985

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By B. Kolonja

A SIMAN and CINEMA PC-based simulation model was developed to simulate and animate the truck-shovel operations of surface mines. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. The statistical analyses were performed and appropriate theoretical distributions were fitted for various time events in the truck-shovel work cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an 'optimal" dispatching strategy to produce an equilibrium between "the quality and quantity of production.

Jan 1, 1993

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By Ronald B. Stone

This paper describes a proposed solution to the problem of mining a 315 foot diameter unsupported sphere at a depth of 2700 feet in a salt dome by conventional mining methods. The proposed solution utilizes many of the varied technologies available to the mining engineer for solving mining and underground construction problems. The following are reviewed in the paper: A. The location of the sphere within the dome as required by construction criteria. B. The relation of the location of the access shafts to the sphere. C. The rock mechanics theory in relation to the salt dome and large size of the excavation. D. The proposed "honeycomb" method of mining which will be a partial answer to rock mechanics stability requirements. E. The equipment which it is recommended be utilized to accomplish the construction. F. The rock mechanics measuring instruments proposed. G. The methods of disposal of the mined salt. Conclusions and areas of further study are outlined in the final statement.

Jan 1, 1968

By M. Scaggs

"Respirable dust in underground coal mines has long been associated with lung diseases, and regular dust sampling is required for assessing occupational exposures. At present, respirable dust concentration and crystalline silica content are commonly determined, but considering recent and yet unexplained increases in the incidence of lung disease amongst miners in specific geographic regions, more information about specific dust characteristics is urgently needed. While particle-level dust analysis is ideal, it is impractical for large numbers of dust samples because it is both time and cost intensive. Thermogravimetric analysis (TGA), however, is an alternative option, which offers the ability to determine the total coal to mineral mass ratio in a dust sample – analogous to proximate analysis of bulk coal samples for determining ash content. Here, preliminary development of a TGA method for this purpose is presented. The method is being developed to evaluate dust collected on mixed cellulose ester (MCE) filters using approved permissible sampling equipment. INTRODUCTION Based on the particle size, airborne mine dust can be classified in three categories: inhalable dust (< 100 µm in size), thoracic dust (< 25 µm in size), and respirable dust (< 5 µm in size) (Ramani et al., 2003). The World Health Organization (WHO, 1999) defines inhalable dust particles as those which can be breathed into the nose and mouth, and thoracic dust particles as those which can penetrate airways of the head and enter the airways of the lung. On the other hand, respirable dust particles can penetrate beyond the terminal bronchioles into the gas-exchange regions (alveoli) of the lungs (WHO, 1999). Hlavay (1992) reported that the seriousness of the damage in the lungs and respiratory tract is based on amount of dust remaining in these organs, and the amount of dust depends on the extent of dust exposure, the size distribution of the dust particles, and the capability of the body for dust elimination. Inhalation of respirable coal dust by miners can cause a disabling and potentially fatal lung disease which is called coal worker’s pneumoconiosis (CWP). Silicosis is another fatal lung disease caused by inhalation of respirable silica dust. In CWP and silicosis, dust particles deposit in the lungs, damage the lung tissue, and ultimately cause scarring which cannot be reversed (Colinet, 2010). While overall incidence occupation-related lung disease amongst coal miners in the US has been declining for over 40 years, it appears that there has been a recent increase in specific locations in Central Appalachia (CDC, 2006; Pollock et al. 2010; Suarthana et al., 2011). Although this trend is yet unexplained, one theory is that particular dust characteristics in these locations may be a factor (Hassan and Lau; Page & Oraniscak 2002). For example, several studies have indicated that different coals may generate different amounts of respirable dust (e.g., see Page, 1993 and Litton and Page, 1994), and the surrounding geology may also play a role in terms of the types of dust particles generated. Although respirable dust concentration and crystalline silica content are commonly determined as part of regulatory compliance sampling, more information about specific dust characteristics (e.g., size, shape and composition) is urgently needed."

Jan 1, 2015

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By Liliana Rybarska-Rusinek, Aleksandr M. Linkov, Ewa Rejwer-Kosińska

Joined modeling of stressed state and induced seismicity is a means to join geomechanics with seismic observations. When applied to quantifying rockburst hazard, it provides, on one hand, estimations in terms of mechanics, such as stress concentration, and, on the other hand, in statistical terms of the risk analysis developed in mining seismology. The modeling became possible due to progress in computers and numerical methods. However, despite tremendous increase of computational abilities, the joined modeling is still quite time expensive. To make it available for wide use and real time simulations, there is need to reduce the time cost of its key stages: calculation of stresses, caused by mining, and simulation of seismic events, induced by these stresses. The present work aims to decrease the time cost. The stages are time costly because of the same reason, which is a very large number N (up to millions) of elements, representing rock structure, openings and flaws. This leads to immense computational complexity (roughly of order N2) of conventional accounting for pairwise interactions between the elements. The complexity may be notably reduced, when employing the fact that interactions decrease with growing distance between elements. Specifically, the fast multipole methods (FMM) avoid the complexity N2, by employing translations of far-fields from whole collections of sources. This reduces the complexity to the order 22, where p is the number of terms involved in a single translation, is the number of translations, and is the dimension of the quantity translated. Still, for conventional FMM, the complexity remains too high to routinely perform joined modeling of stresses and seismicity.

Apr 26, 2022

"Longwall shearers are widely employed in underground coal mines. The reliability of such machine has significant importance for successful mining operations. This paper aims at studying reliability of a longwall shearer using failure data recorded for a year. Data was pre-processed, sorted and selected for analysis. Selected data is then examined using statistical models. Distribution fitting of time-between-failure (TBF) and time-to-repair (TTR) are accomplished using three different models. Goodness-of-fit criteria is used to ascertain the best fitting model. Reliability in terms of mean-time-between-failure (MTBF), and mean-time-to-repair (MTTR) are calculated using the model which best represents the failure data. Exponential distribution best represents the time between failure and lognormal distribution the time to repair data. A well-known risk management technique Failure Mode Effect and Criticality Analysis is used to evaluate the critical breakdowns. Critical system/parts, experiencing regular failures is delineated based on this analysis. INTRODUCTION Mining is a capital intensive process, and huge monetary investment is required to develop and operate a mining project. Heavy and expensive equipment’s are employed in development and operation of these projects. In order to ensure timely completion of set milestones, it is mandatory that equipment’s perform their required task productively. Delays are not unusual owing to breakdown of these equipment’s. Breakdown or failure experienced by any of the equipment pose heavy financial burden. Moreover, frequent times, companies have to employ and dedicate additional resources to make up for such delays. Delays in project is not only detrimental to company’s image in market, but it also interrupts customer commitments. Mines having history of not fulfilling their promise usually get lower commodity price. Penalties are also imposed on the companies defaulting its obligations. Especially, in today’s world where competition among the companies are growing, success means keeping up the commitments in a timely manner. Heavy machinery and equipment are instrumental in success of any project. These machinery and equipment’s have to reliable in a sense that they can perform the set task in given time period. Reliability of these equipment plays a pivotal role in success of any project. The reliability analysis of mining equipment has long history. Many researchers have applied different statistical models for analyzing the reliability of mining machines (Samanta, Sarkar [1]. Kumar and Klefsjö [2] demonstrated the use of the power law process model for reliability assessments of repairable mining machines. Barabady and Kumar [3] performed the reliability analysis from failure data of the crushing plants."

Jan 1, 2018

By M. K. Rizkalla

This paper discusses the time-dependent behaviour of rock when it involves the presence of several layers of rock strata in the vicinity of mine openings, mining in sequences and the placement of backfill. The paper describes numerical techniques which proved useful when such situations are encountered in practice. The model is elastoviscoplastic. At given time stations, short term loading or changes can be made to the creep behavior of the rock. The modelling technique is first described and is followed by simulations of stresses and displacements in a potash mine with the primary objective to demonstrate the effect of such aspects as mining and fill sequences in 3-D. This involves cutting finite elements representing the strip of the mining face and simultaneously filling those elements representing the newly placed fill. The stiffness of the fill varies with the degree of compaction at each point. In this way, the effect of the time of fill placement, the gap between the top of the fill and the back as well as the degree of compaction are simulated. The second example is a 2-D problem simulating the long term effect of backfill, as a material compacting with time, on the settlement of the layers above it as well as the closure of the room.

Jan 1, 1996

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service&apos;s Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By Reynold Q. Shotts

Underground mines, penetrating well below the water table, quickly fill with water when abandoned. Ordinarily, these natural cisterns are not thought of as sources of industrial water. Under special circumstance, if chemically treatable, they might become valuable industrial water reservoirs. An example of a group of about 20 mines in a geological and structural setting insuring water entrapment, rapid recharge and a possible minimum of contamination, are the small, compact Belle Ellen and Piper basins in Alabama&apos;s small but second most productive coalfield, the Cahaba. The mines have been abandoned from more than 50 to less than three years. The county now produces about a million tons of coal annually, all from strip mining. Figure 1 shows an idealized cross section of the strata in the Belle Ellen syncline near West Blocton, Bibb County, Alabama. Figure 2, 3 and 4 are maps showing the location of the syncline, other structural features, the outcrop lines of the three principal coalbeds underlying the basin, and the mined-out areas on the three beds (1).

Jan 1, 1973

By R. Venkataramani

Crushed stone operations have become more difficult due to rising costs of labor and equipment, with the consequent reduction in profit margins. Competition from other operators and the encroachment of vertically integrated companies place severe restrictions on available markets. The seasonal demand for stone precludes any definite production level, and changes in productivity have to be accommodated. These influence profitability, and therefore production plans must be continuously adjusted to keep pace with rapidly changing conditions. The basic problem of stone companies seeking to maximize profits is one of balancing stone production costs, costs of inventory holding and stock-piling, marketing costs and any other charges accruing over time against the selling price of stone. Because of high peak demands, slack period production must be stored and then distributed to supplement peak period production. For a multi-plant operation, there is a need to evaluate at the same time the interaction between the plants and the various marketing sectors. In a multi-plant operation with different production capacities and production costs, stone producers are interested in the answers to the following questions: 1. How much stone should be produced at each plant in each time period? 2. What should be the optimum stone shipment from each plant to each market? 3. What are the effects on net returns and shipping plans, if production capacities are altered at the plants? These questions have many different answers that, will satisfy demands. From the point of production scheduling, the minimum production cost may be the objective. From the inventory standpoint, the best solution will be to synchronize production with sales. However, when the transportation of stone is also considered, the desired end is to achieve that delivered cost which maximizes the company f s net return. Besides, only an extremely naive analysis ,wouId attempt to

Jan 1, 1971

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977

By A. J. Naldrett

Over the past six or seven years important new ideas have been developed concerning the origin of nickel sulfide deposits. To a large extent these have been stimulated by the major nickel discoveries of the Eastern Goldfields area of Western Australia (Woodall and Travis, 1969; Ewers and Hudson, 1972). Prior to these finds, the most important nickel camps were regarded as being associated exclusively with intrusive rocks such as the Nickel Irruptive at Sudbury or the intrusive peridotites at Thompson, rocks that were thought to have no close association with volcanism. Study of the Australian discoveries, coupled with work in South Africa (Viljoen and Viljoen, 1969) and Canada (Naldrett and Mason, 1968; Pyke, Naldrett and Eckstrand, 1973), has shown that volcanic rocks with true ultramafic compositions and extrusion temperatures of 1400 to 1600°C were a common feature during the Archean. Under certain circumstances economic concentrations of nickel sulfides have formed from these rocks, either settling to the base of their associated flows or accumulating in shallow intrusive feeders to the flows. The aim of this article is to show how these ultramafic rocks can be recognized, how the nickel deposits, if present, are likely to occur within them, and what special features characterize ore-bearing examples of the rocks.

Jan 1, 1975