Search Documents

By Christopher Laughton, Michael P. Bruen

At Fermilab, a 4000-ft long underground complex has recently been constructed for a high-energy physics experiment. The complex is sited up to 350 ft, below grade principally in bedrock. The rock excavations were mined by TBM and drill and blast methods and supported by a combination of rock bolts, dowels and shotcrete. Water control was achieved using a combination of pre- and post-excavation grouting, drainage systems, drip shielding and air desiccation measures.

Jan 1, 2003

By Jr. Raleigh

In a cooperative agreement between the U.S. Bureau of Mines and the U.S. Department of Energy, laboratory column-flotation tests were conducted to evaluate fluorosurfactants as selective fine coal flotation collectors. A Middle Kittaning seam coal responded to flotation with both anionic and nonionic fluorosurfactants. These fluorosurfactants were no more selective than MIBC alone. However, for increasing coal yields, nonionic fluorosurfactant systems did not increase total sulfur and ash contents as sharply as MIBC systems. Flotation selectivity also improved slightly when a combined anionic fluorosurfactant-MIBC system was used in acidic pulps (pH < 3.6). While the fluorosurfactants examined will not likely have direct application in current coal flotation practice, other fluorosurfactant systems could eventually prove beneficial for floating fine coals.

Jan 1, 1990

By W. A. Cincilla, S. C. Tadolini

INTRODUCTION Resin bolting systems continue to gain popularity in underground coal mines in the United States, and their general success under a wide range of geological and operational conditions is well documented. In 1984, 36% of all bolts used were resin-grouted systems. However, many questions dealing with basic support mechanisms and the influence of various factors on bolt effectiveness in situ remain only partially answered. The Bureau of Mines&apos; Denver Research Center conducted a major research project to investigate the influence of installation procedures on the effectiveness of resin-grouted roof bolts. The project consisted of two main studies: the first dealing with the contribution of bearing plates to the load-carrying capability of the bolt; the second examining the relationship between installed grout column and the anchorage capacity as measured by the standard pull-out test. Additionally, a finite-element computer model and other analytical and empirical techniques were applied to aid in the basic understanding of the test procedures and to examine the load transfer mechanism in resin-grouted bolts, which to date has not been comprehensively assessed. The plate study includes field test results from two mines (Fig. 1). At these test sites two behavioral parameters were measured: the actual loads that bearing plates were subjected to when installed in conjunction with full-column resin grouted bolts, and the roof movements generated by the applied loads. Results indicate that bearing plates are subjected to varying degrees of loading, which range from conventional installation pressures of 2.2 kN (500 lb), up to a measured load of 142.4 kN (32,000 lb) when the immediate roof is shifting and deforming. These measured loads indicate that the bearing plate is an integral part of the support system. Differential sag stations, installed to monitor roof displacements in the test sites, show the highest degrees of loading occur in conjunction with the largest amounts of movement. The column-length study addresses possible reductions in anchorage capacity of "full column" bolts. These reductions could result from such factors as the loss of grout to surrounding strata, or improper mixing of catalyst and resin. Field test sites were established at eleven mines located in major coal mining districts throughout the United States (Fig. 1). Four major roof-rock types were represented in the study: shale,

Jan 1, 1986

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By J. C. Stankus, R. Ochsner, B. Hanson

"Bull Mountains No. 1 mine of Signal Peak Energy made another success in its 4 Right pre-developed recovery entry on March 23 and 24, 2015, after the first successful cut-through and shield retrieval of 3 Right pre-developed longwall recovery entry in 2014[1]. Under the same geological conditions, the major difference of 4 Right and 3 Right is the 600 psi Unconfined Compressive Strength (UCS) value of light-weight concrete in 4 Right versus 800 psi in 3 Right. In addition, one more recovery chute was added in 4 Right. The unique geological conditions in this mine include: (1) the low overburden of approximately 200-260 ft, (2) prevalence of roof joints parallel to the face in the sandstone/siltstone dominated overburden, (3) proximity of the Rehder rider seam to the bench Mammoth coal seam, and (4) prompt surface subsidence with the face advancement. The 4 Right recovery entry was 42 ft wide and developed in two stages, 20 ft wide in the inby Phase I, and 22 ft wide in the outby Phase II. The entry roof was reinforced with steel wire mesh/non-metallic recovery mesh, primary bolts, and high-capacity supplemental SUMO cables. After all the support was installed, the entry was completely backfilled with specially designed, cuttable, low-density cement. It took approximately half time to easily cut through the concrete with less dust in 4 Right as compared to the concrete-cut-through time in the 3 Right. The updated study further explored the nature and mechanism of effective roof control approaches in the pre-developed recovery entry of this unique geology mine, aiming at providing the safest working environment for protecting the miners. GEOLOGICAL AND MINING CONDITIONS OF THE RECOVERY ENTRIES Bull Mountains No. 1 mine is located 30 miles north of Billings, Montana, and currently mines bituminous coal from the Mammoth coal seam. The mine employed a conventional recovery face in Panel #1 and pre-developed recovery entries in Panels #2, #3, and #4 (Figure 1). The typical mining and geological conditions are as follows:Overburden Depth The overburden above the Mammoth coal seam in the #1-#4 Right recovery areas is approximately 200-260 ft. This low cover, in combination with specific roof geological features (especially the prevalent roof joints and proximity of rider seam), constitute unique ground movement characteristics when the longwall face advances into the recovery entry if no sufficient roof support is installed."

Jan 1, 2016

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950&apos;s a number of anionic iron procedures were evaluated and in the late 1950&apos;s and early 1960&apos;s the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis&apos;, Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960&apos;s The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral&apos;s surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By L. L. Damon

A geochemical study of cyanide neutralization processes was conducted at Brohm Mining Corporation to gain a better understanding of the leach pad behavior and to develop a simplified procedure to quantify the attainment of compliance with permitted cyanide neutralization criteria. Such attainment is a prerequisite for off-loading spent ore from the leach pad at the "load/unload" gold heap leach operation. The geochemical study program consisted of size fraction analyses and weak acid dissociable (wad) cyanide analyses for various sections of the spent ore from the actual leach pad. Further testwork included size fraction analyses and wad cyanide analyses on the ore from four 29 foot laboratory test columns which were leached and neutralized with different neutralization treatments in parallel with an actual active leach pad. Wad cyanide was analyzed daily on the neutralizing columns and various parameters were monitored weekly on the influents and effluents during the leach cycle and neutralization period. A comparison was made of neutralized effluent chemistry and porewater extraction fluids, as well as an analysis of the selective adsorption of cyanide on various particle size fractions.

Jan 1, 1992

By G. Ahuja

Tests were conducted to investigate the effects of cyclone geometry, operating conditions, and particle size on magnetite classification. The effects of these parameters on the partition curve for narrow size fractions were studied using a 25mm diameter cyclone cleaning -150 µ m coal. Additional tests were run to investigate the effects of geometry and operating conditions on the slurry, solid, and water splits. The relationship between the relative density of the underflow stream and the relative density of separation was also investigated. This paper presents the results from this study.

Jan 1, 1994

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By S. K. Kawatra

In most operating coal-cleaning plants, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. Reducing the pyrite recovery first requires that the primary recovery mechanism should be Identified, as different measures are required for reducing entrainment, locked-particle flotation, or true hydrophobic flotation. In this paper, evidence is presented which suggests that hydrophobic flotation is not an important mechanism for recovery of liberated pyrite from freshly-ground coal when the collector is a neutral oil, and that the bulk of the floated pyrite occurs either as a result of simple entrainment or by mechanical locking with floatable coal particles. Column flotation results are also presented which show that significant sulfur reductions can be achieved by reducing levels of entrainment.

Jan 1, 1992

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

Geostatistical literature has been dealing with recoverable reserve estimation techniques for the last 30 years. There have been well established support correction techniques (Le. affine correction, indirect log-normal correction, etc.) to deal with volume -variance relationship globally in determining what will be the reserves above a cutoff grade during mining. Kriging has become the accepted technique in the mining industry for ore reserve estimation. Many large companies are using this method for gold and copper deposit modeling. In general, the estimates coming from kriging are smooth. The variances of the block grades estimated by kriging are often lower than the material that will be mined selectively. As a result, kriging tends to under estimate reserves at high cutoff grades and overestimates them in low cutoff grades. It is necessary to perform additional steps after kriging if the goal is to determine recoverable reserves at some cutoff and not the in situ resources. In the mining industry, it is becoming more and more common for the low grade heap leach projects to consider whether the higher grade portion of a deposit may be processed by a mill at higher profits. Similarly, a concentrator -refinery operations are implementing heap leach -SX-EW option for the lower grade portion of their deposit. These options are making it very critical to estimate the low and high end of the grade distributions more accurately. Ore reserve estimation is normally done by using widely spaced exploration data which has very small size support (Le. core samples). Selective mining is carried out on ore control that is based on closely spaced blasthole data normally averaged into larger polygons based on some cutoff grade. Estimated grades from exploration data need to reflect the variability of the grades of the selectively mined units if they are used without further adjustments to predict recoverable reserves.

Jan 1, 1997

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION This manuscript is based on site inspections of five existing mines and the detailed analysis of two of the five. The detailed analysis and mathematical models of the two mines are presented herein in order to demonstrate a method of predicting mine water inflow using existing mines as a data base. Water management procedures were studied at all mines. Our original criteria for mine selection were that the mines be less than five years old and have an inflow rate in excess of 2000 gpm (7.6 m3/min). Background hydrologic and hydrogeologic data were required so that two of the mines could be used for our computer modeling experiments. Our original criteria proved to be difficult to meet. We contacted numerous mines via various sources. Many mines were unable to meet the cri¬teria stated or were not interested in cooperating with us. Therefore, we allowed some flexibility in the application of these criteria to satisfy our orig¬inal requirements. Although the visitations at all the mines are not discussed herein the characteristics of the two mines simulated are presented. These simulated mines consist of a uranium mine in New Mexico and a lead mine in Missouri. The mines and owners will remain anonymous by request. URANIUM MINE-CASE HISTORY NUMBER 1 Mine Location The uranium mine that we simulated is located in northwestern New Mexico. The ground surface at the uranium mine is at an elevation of approx¬imately 7000 ft (2134 m) above mean sea level. The climate is arid to semi-arid with an average annual precipitation of approximately 10 in. (25.4 cm) (John and West, 1963). Geologic Setting It is essential that a conceptual model of the stratigraphy, hydrostratigraphy, and structural geology of a mine site be developed prior to simulation by a mathematical model. If such a conceptual model is not developed prior to simulation major errors are difficult to avoid. The uranium mine we have simulated is located in the San Juan Basin (Fig. 68), which is a structural basin located in northwestern New Mexico and adjacent parts of Colorado, Arizona, and Utah. The sedimentary rocks present in the deepest part of the basin are nearly 15,000 ft (4572 m) thick (John and West, 1963). The regional dip of the sedimen¬tary rocks in the Grants area is generally northward toward the San Juan Basin; the regional attitude is modified locally by normal faults and folds (Hilbert, 1963). The rocks of interest in this area are sedimentary in origin and range in age from Penn¬sylvanian to Cretaceous. They rest on the Precam¬brian core of the Zuni Uplift. Associated intrusive and extrusive rocks are of Tertiary and Quaternary ages (Hilbert, 1963). The deepest sedimentary unit of interest at this mine site is the Morrison Formation as described by Hilbert (1963). The Morrison Formation con¬sists of three members in the general area of the mine site; the deepest member is the Recapture. The Recapture Member consists of alternating beds of gray sandstone and grayish red siltstone or mud¬stone with strata up to several feet in thickness. Only a few small deposits of uranium are contained within the Recapture Member. The Westwater Canyon Member overlies the Recapture Member of the Morrison Formation. The Westwater Can¬yon Member is approximately 150 ft (46 m) thick and consists of light brown to gray, poorly sorted, arkosic sandstone, and some interbedded gray mud¬stone. The Poison Canyon Formation denoted in subsequent discussions, tables, and figures was de¬termined to be a part of the Westwater Canyon Member. The separate connotation is used for the description of mining operations and hydraulic properties but a separate physical description is not included. This member of the Morrison Formation contains many large deposits of uranium. This is (some pages in this article are damaged)

Jan 1, 1986

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By Donald E. Ralston, V. Rajaram, Michael N. Greeley, John W. Peters, Terry J. Laverty, F. S. Kendorski, Peter G. Chamberlain, J. Brent Hiskey, William C. Larson

Preliminary figures from the US Mine Safety and Health Administration show 801 underground metal mines and 490 surface metal mines, at the end of 1981, up from 663 and 383, respectively, in 1980. Preliminary MASH figures also show 207 underground nonmetal mines and 1070 surface nonmetal mines at the end of 1981, compared with 167 and 1092, respectively, last year. In addition, preliminary MASH figures show there were 14,676 mineral extraction operations on the surface and 3845 underground at the end of 1981, versus 14,951 and 3675, respectively, for last year. The number of mines, then, in three of four categories increased significantly, while having a lower net total of just 2% in the other category. And the number of underground extraction operations increased nearly 5% for the year, while surface operations were down less than 2%. But despite operations totals that mostly held their own or showed significant increases, it was a tough year for the nation&apos;s mining industry. The nonferrous segment of the industry had a bad year and 1982 may be no better, according to Business Week (Jan. 11, 1982), which adds that a turnaround is impossible unless the general economy recovers. Even then, with diminishing markets and overcapacity plaguing its products, the mining industry&apos;s condition "will be far from robust," the magazine says. The basic problem is that nonferrous metals-aluminum, copper, lead, molybdenum, nickel, and zinc-are tied to the most troubled sectors of the US economy. As recently as 1979, for example, more than 40% of all aluminum shipments went to the construction and transportation industries. Last year, these markets were down to 35% of aluminum shipments. And molybdenum sales to steel producers dropped by nearly 15% last year. Moreover, nonferrous products ended 1981 at disastrously low prices. Molybdenum oxide sold at $8.77/kg ($3.98/lb), half its $17.63/kg ($8/lb) price earlier in 1981 and aluminum was listed at $1.08/kg ($0.49/lb), compared with $1.54/kg ($0.70/lb) a year earlier. The Comex price of copper was $1.54/ kg ($0.70/lb), down from $3.11/kg ($1.41/lb) in early 1980, in real terms the worst copper price in 30 years. Lower prices led operators to cut their output and increase layoffs, shut down mines, and defer capital spending projects. In December, Duval Corp., a Pennzoil Co. subsidiary, shut all four of its US copper mines until March. Aluminum Co. of America had laid off 7.3% of its work force, shut nine of its 38 smelting lines, and entered 1982 operating at only 68% of capacity. Inco Ltd., the Free World&apos;s largest nickel producer, lost money in 1981, an estimated $11 million, for the first time since 1932. And, like Falconbridge Nickel Mines and other major nickel producers, had cut back on nickel production and was operating at only 63% of capacity (Forbes, Feb. 15, 1982). Amax, the country&apos;s largest molybdenum producer, had cut production by 20%. And Hanna Mining Co. sold lead for $5.07/kg ($2.30/lb), about $1.54/kg ($0.70/lb) below what it cost to produce. Another problem is that copper companies in the next few years must come to terms with problems of aging smelters. Some companies are simply closing them. In 1980, Anaconda closed its 75-year-old Butte, MT, smelter and is shipping concentrates to Japan, rather than modifying the smelter to meet environmental requirements. And oth Phelps Dodge Corp. and Asarco Inc. have antiquated smelters on which they will have to make decisions. The most troubled metal in 1982, Business Week said, will be molybdenum, with no real recovery in sight until the mid-1980s. High molybdenum prices in the late 1970s, caused in part by shortages, triggered overexpansion that will take years for the US market to soak up. On a more upbeat note, 1981 mergers might help stabilize the industry by providing funds for mining companies. Standard Oil Co. (Ohio) said it plans to spend $7 billion on Kennecott during the next 10 years for modernization and expansion. And Atlantic Richfield Co. said it will spend $500 million on Anaconda Copper Co. during the next five years. Another positive note was sounded by T. H. Adams of the United Banks of Colorado Inc. He said he expects the mining industry to experience moderate growth in 1982, led by "interest rate sensitive" demand from energy, electronics, and defense markets. And mining will be helped by "weak, but improved" construction and auto markets. The mining industry will be operating in an economy stronger than 1981, but still relatively sluggish by postwar standards, Adams predicted. Iron Ore Estimated US iron ore production in 1981 was 75.2 Mt (74 million long tons), up 6% from 70.7 Mt (69.6 million long tons) in 1980, though down from the 87.1 Mt (85.7 million long tons) produced in 1979. The mine value of usable iron produced from domestic mines was estimated at $3 billion. US iron ore was produced by 28 companies operating 35 mines, 26 concentration plants, and 16 pelletizing plants. The mines included 34 open pits and one underground mine. Byproduct ore recovered from copper- and titanium-mining operations accounted for less than 1% of total iron ore production. Fifteen mines operated by nine companies accounted for 94% of total

Jan 5, 1982