Search Documents

By A. J. MacKellar

The economic viability of any project is generally assessed on an evaluation of the total capital constructed costs along with operating costs, owner's costs and market conditions. This paper will be directed to the role that Cost Engineering plays in the development of the capital costs and the cost control techniques applied thereto.

Jan 1, 1975

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

Several major impediments threaten the successful delivery of tunnel and under-ground construction projects. In addition to technical design and construction risks associated with tunnel projects, many of which are well understood, budgetary pressures, funding constraints and the complexity of procuring, administering and executing multiple concur-rent projects in a large program could also have a catastrophic impact on the program?s objectives. Contributing factors often include poorly managed design, procurement, construction, managerial, organizational, market and stake-holder risks, as well as nonconforming inputs or outputs to the costs and schedule, or any other potential inabilities to deliver the required or desired results. A strategy to prevent ?failure? of a project requires a proactive and holistic approach to risk management. Through planning, identification, analysis, management, monitoring and control of the project?s risks (both threats and opportunities), attention to management of risk will in-crease the probability and impact of positive events and decrease the probability and impact of events adverse to a project?s objectives.

By D. J. MacKinnon

Smooth, compact, dendrite-free, 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartment con- taining DSA anodes which were separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air-sparging. The catholyte passed through the diaphragm into the anode compartment from which chlorine gas and spent anolyte were withdram.

Jan 1, 1980

By R. E. Pennington

My subject this morning is coal liquefaction technology. Actually, coal liquefaction involves a number of technologies in a very complex system. The first slide shows the major components of such a system with arrows to indicate appropriate flows. The components are the facilities for coal feed preparation and handling; the coal hydrogenation or base liquefaction section; facilities for product separation and recovery, and in addition, facilities for the production of hydrogen from coal-based sources. A very rough break- out of the investments involved in these areas is given at the bottom of the slide. Investment is spread about equally among the three areas of operations Another way of looking at it is that the investments in what might be called support facilities are of the same magnitude as the base investment in the hydrogen facilities. Therefore, it is appropriate in a discussion of coal liquefaction technology to treat it as a system composed of a number of technologies. The next slide lists the various functions in the feed preparation section along with an indication of technology status. Storage, crushing, grinding, drying of coal all have been in commercial practice for a number of years. The slurrying and pumping of coal at least in water slurries, is practiced commercially also. The heating of coal slurries in oil to high temperatures under pressure is not in commercial practice and development and testing is going on by a number of people in this area. Some rather complex phenomena occur when coal oil slurries are heated to high temperatures.

Jan 1, 1975

By Girish Roy, Robert Goodfellow, Angel Del Amo, Bingzhi Yang

Designing and constructing tunnels in seismic prone areas present unique challenges to both designers and contractors. The Westside Purple Line Extension Project– Section 3 in Los Angeles requires crossing an active fault that may subject the tunnels to extreme structural demands. In order to ensure that the linings will safely accommodate the fault movement, a revolutionary composite section—steel plate embedded in the intrados of the precast concrete segmental tunnel lining was finally selected. Additionally, continuous expansion steel plates over the circumferential joints will be installed to mitigate the potential opening of the circumferential joints.

Jun 13, 2021

By William F. Brandom

INTRODUCTION Cross, et al. (1974), produced a retrospective study of standard setting for underground miners. This report had two distinct components; i) criteria of importance for the protection of the miners, and ii) economic considerations for standard setting. The methods for setting radiation safety standards reviewed were: dose calculations and consensus methods; epidemiology; pathology; bioassay; animal experiments; sputum cytology; chromosome aberrations; and, the Mantel-Bryan Model. By looking back, the authors intended to enable officials to look ahead in making future decisions based on reasonable conclusions. Now it may be time to consider underground miners' protection from another perspective: are there miners who may be especially susceptible to toxic environments?; and if so, are there any biomedical assays that might be indicative of exceptional sensitivities to toxic substances? The human population is genetically very heterogeneous. The data of Saccomanno, et al. (1973), reveal great variability in individual response to radon daughter exposure and only a small portion of the miner population subject to toxic inhalants develop squamous cell metaplasia (Saccomanno, et al., 1970). The majority of the miner population is either not susceptible or is resistant to the toxic agents. This information suggests the existence of a small subpopulation with increased sensitivity or reduced resistance and underscores the need for indicators from biomedical assays that might prove of value for the detection of such individuals. The heightened awareness of the contribution of pollutants in the environment for the potential induction of mutations and carcinogenesis lead to a profusion of short-term bioassays to circumvent the high cost and time-consuming large toxicity animal studies. Over 100 bioassays across taxa from microbes to man are at various stages of use or development (Hollstein, et al., 1979). Less than a dozen tests currently offer early promise for application to[ in vivo] effect studies of man. Many are still in early development, lack the sensitivity needed for a retrospective or prospective study at current permissible exposures, are impractical to conduct in the field, or are not cost effective. The purpose of this paper is to review some of the bioassays that may now, or in the near term, prove applicable for the detection of individual underground miners with increased susceptibility to toxic agents. Throughout this statement, it is assumed that any single test may give false negatives or false positives and, therefore, a tier of tests should be investigated. The possible tests are in various stages of development; some tests better proven than others with a firmer data base and, therefore, with greater probability of usefulness. Some of the less proven assays are not ruled out if they have practical or theoretical promise as indicators. Table I summarizes the assays critiqued for their potential to monitor the effects of [in vivo] exposure to genotoxic substances. POTENTIAL INDICATORS OF HIGHLY SENSITIVE MINERS Assays of Body Fluids It is desirable to have data on the agent(s) to which subjects are exposed when humans are monitored by biomedical effects. Obviously, to varying intensity, the underground mining environments are monitored for radon daughters and it is recognized that the miners are also exposed to other pollutants, most notably, uranium ore dust and diesel fumes. Further testing for the metabolites of the pollutants can be done on body fluid, urine. [High Performance Liquid Chromatography (HPLC)]: This is a very sensitive method for the detection of mutagenic metabolites in urine. The urine is treated with the enzyme sulfatase and beta-glucuronidase to permit identification of substances that are made nonmutagenic by conjugation as glucuronides. The sample is then passed through an XAD-2 resin column and the absorbed organic molecules eluted with acetone. The sample is then split and evaporated to 1 ml and used for direct chemical analysis using HPLC. One drawback to the test is the inability to measure cumulative exposure, but multiple samples can be obtained and comparison to baseline (control) and exposure samples can reveal qualitative differences as a consequence of exposure to mutagens. [The Ames/Salmonella Microbiological Assay]: The Ames/Salmonella microbiological mutagen test is the most extensively used short-term bioassay, with over 2,600 chemicals having undergone testing by this method (Hollstein, et al., 1979). The method, thoroughly worked out and tested for 10 years, consists of taking the second split urine sample from the HPLC preparation, evaporating to dryness and dissolving in dimethylsulfoxide (DMSO). The sample is then applied directly to

Jan 1, 1981

By K. G. Wallace

In 1982, the US Congress passed the Nuclear Waste Policy Act (NWPA) to provide for the development of an underground repository for spent nuclear fuel. This development will be managed by the US Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository. Those sites were: (1) a site in volcanic tuff located at Yucca Mountain in Nevada, (2) a site in bedded salt located in Deaf Smith County in Texas, and (3) a site in basalt located in Hanford, WA. At present, conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation system designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be reestablished to allow reentry into previously closed rooms for the purpose of inspection, maintenance, or retrieval.

Jan 1, 1988

By Michael G. Zabetakis

Effective accident prevention programs utilize a broad spectrum of activities, including meaningful training programs. In practice, such programs must be directed towards specific, defined needs. These needs are considered here for three categories of employees: new, re-assigned, and experienced.

Jan 1, 1983

By Stig Premfors

Lamco Joint Venture is operating a Dravo Pelletizing machine to produce pellets from the natural slimes of an earthy hematite ore. The grate area of the machine 3.3 x 106 m equal to 350 m2 (3800 sq. ft.) and the installed fan capacity is 8200 HP. The limiting factor for production is normally fan capacity. This means that the processing fans can not pull the additional air (i.e the additional calories or BTUs) through the bed which would be required for increased production. A way to increase production without major modifications is to supply the additional calories needed for increase production by adding coal to the pellet feed. After successful laboratory tests following method of coal addition has been chosen and the following results have been obtained. 1. The ground coal is added to the slurry prior to the filters and the rotary dryer. 2. By adding 0.6% coal, an increase of about 15% in production rate has been obtained. 3. No significant changes of metallurgical properties have been observed (i.e. tumbler index, compressive strength, ferrous iron content, reducibility, Linder degradation and swelling). 4. No unexpected operation problems have been experienced. The pellet discharge temperature increases and is the limit for how much production can be increased by coal addition without making plant modifications.

Jan 1, 1971

By William Cass, Ellen Caftel Turcotte

The Elliot Lake Centre was established in 1965 as an independent Centre for Continuing Education offering a variety of adult education services. In 1976 all retraining and community college type activities were transferred to the Sault College of Applied Arts and Technology which had opened a branch campus in Elliot Lake. Upon the completion of this transfer, the Elliot Lake Centre was then contracted in 1977 by the Canada Centre for Mineral and Energy Technology to study the feasibility of establishing a research and information institute dealing with various health and safety concerns of the uranium worker. By late 1980, a federal charter was granted for the establishment of the Canadian Institute for Radiation Safety, made possible through the cooperative efforts of the Governments of Canada and Ontario, the Ontario uranium mining and refining companies, and the Elliot Lake Centre. On 1 April 1981 the Institute officially began operations. PROGRAM DEVELOPMENT AND COORDINATION In May 1978 the Elliot Lake Centre initiated a voluntary sputum cytology program for uranium workers. This program was financed by the Ontario uranium mining companies: Agnew Lake Mines Limited near Sudbury; Madawaska Mines Limited in Bancroft, and Denison Mines Limited and Rio Algom Limited in Elliot Lake. In 1981 additional funding was granted by Eldorado Nuclear Limited for a small group of employees at the company's uranium refinery in Port Hope, Ontario. Initially in 1978, program participants were accepted according to length of employment, radiation exposure levels (calculated in working level months) and/or smoking history. These restrictions were abolished within a few months and all uranium workers were encouraged to participate. From 1978 to 1979 the sputum cytology program was medically directed by personnel from the Montreal Cancer Institute. Until 1979 all data maintenance for the program was performed manually, however the effort required to sustain the system increased significantly as the number of participants grew. In September 1979 the Division of Thoracic Surgery at the Toronto General Hospital, under the direction of Dr. F.G. Pearson, submitted a proposal to the Elliot Lake Centre to develop a data processing system to help coordinate the surveillance program. In October 1979, Dr. Pearson became the new Project Director. Director of the Cytology Program is Dr. D.W. Thompson of the University of Toronto who is responsible for all cytologic analyses. Developmental work to establish the new surveillance system was initiated in January 1980 and became fully operational at the beginning of March 1981. The following sections describe the Elliot Lake operations of the sputum cytology program now conducted by the Canadian Institute for Radiation Safety. PROGRAM PARTICIPATION As of 1 September 1981 the sputum cytology program has 518 participants enrolled. Eligibility is restricted only to a willingness to participate and the ability of an individual to produce adequate sputum samples. Each participant registers for the program at the Institute and is given personal instruction on methods of sputum collection. The majority of the participants in this program are employed by the uranium mining industry; some work for firms which are contracted by the larger companies. Many participants are either retired from the work force or receive disability pensions or workmen's compensation benefits. Other participants have been employed in the uranium mining industry and have since gone on to other employment; some work for various federal and provincial governmental agencies concerned with the mining industry. Some participants are referred to the program by their family physicians because of smoking histories and/or various respiratory conditions. A small number of these individuals have never been involved in the mining industry at all. A chart describing program participation by employment is found in Appendix 1. PROGRAM REGISTRATION In the Elliot Lake area, persons interested in registering in the program are required to go directly to the Sputum Cytology office located at the Canadian Institute for Radiation Safety. Each individual is interviewed personally by the Program Officer. For the employees of Agnew Lake Mines, Madawaska Mines and the Port Hope refinery of Eldorado Nuclear Limited, registration is possible during the Program Officer's semi-annual on-sitevisits. Participants are assigned, in chronological order, "program numbers" for easier identification. File labels are color-coded according to place of residence or, in some instances, place of employment. Each file is stamped with the date each sample bottle is distributed. A file contains: all original test results, a completed registration

Jan 1, 1981

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

By L. L. Oriard

There are certain site-specific geological and physical features of a rock mass which control its behavior under the dynamic stresses induced by the action of explosives. It is essential that blasting technology be adapted specifically to those features. There does not exist a single, simple "right" way for each type of blasting operation, but rather each operation must be custom-designed for each site. When this is done, it is often possible to produce unusual but highly desirable end resglts, such as undisturbed narrow rock walls, monoliths and square benches. Although the techniques illustrated here were developed specifically for "sculpture blasting", the geomechanics principles would apply to other types of blasting control, both large-scale and small-scale. Because the techniques are designed more for the purpose of modifying the site responses which would ordinarily be expected than they are to developing new "blasting formulae?, the name "Modified Site Response Blasting" will be used.

Jan 1, 1984

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993

By Robert S. Foote

The U.S. Energy Research and Development Administration (ERDA) is currently conducting a national program to survey for uranium the conterminous United States and Alaska by 1980 using airborne and surface techniques. This paper discusses the techniques used and some of the results of airborne surveys conducted to date by Geodata International, Inc. Airborne gamma radiation and the earth's magnetic field data are measured to provide data leading to regions potentially more favorable for the exploration and discovery of uranium ore. High-sensitivity radiometric and magnetic field data have been gathered from an aircraft with an average surface altitude of 400 feet (Figure 1). Under most conditions, data are usable up to an aircraft surface elevation of about 1250 feet where limitations will be discussed. Results of data analysis under GJO-1632, GJ0-1644, GJO-1654 and GJO-1663 will be discussed.

Jan 1, 1976

By Karin Bäppler

Mechanized tunnelling is undoubtedly one of the most innovative disciplines in the international construction industry. Technological progress in the planning and production of most modern infrastructure is constantly striving for new records on basis of highly specialized solutions and know-how. Humans and technology have accomplished excellent achievements over the past few years in varied, difficult terrain. New length records are being set with the 64 km long Brenner Base Tunnel and the HS2 Railway system currently under construction in Europe. Cities are building ever longer and more demanding sewer tunnels. The paper highlights some of the challenges, trends and innovations of long-distance tunnelling projects.

Dec 1, 2022

By R. Wisniewski, S. Schafrik

Every underground coal mine in the United States must deploy and operate a wireless communication and electronic tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. This paper assumes that the tracking system uses the communication system to perform its operation. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 24 hours, and the requirements in the MINER Act for the tracking systems to be “functional, reliable and calculated to be serviceable” and the communications systems “redundancy.” These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using tools that are available to and commonly used by the reliability, maintainability and availability community.

Jan 1, 2014

By Grant R. Brown

The objective of this paper is to describe a study sponsored by the U.S. Department of Energy during which a model was developed to optimize haulback mining procedures in single and multiple seam contour mines, The study objective was to achieve financial- based productivity increases approaching twenty percent. This paper reviews the results of the first year's Phase I activities, which include four main tasks: formulate a methodology that can be used to select equipment and mining procedures that result in optimal performance in a particular haulback mining situation; conduct field studies of representative single and multiple seam mines to obtain quantitative background information for development of the formulated methodology: develop the methodology into a useful design tool for mine operators; and prepare plans for field tests to evaluate the effectiveness of the developed tool.

Jan 1, 1981

By H. Zhao, R. Liao, W. Qin

Theoretically, controlling redox potential to a relatively low value and inhibiting jarosite formation on the chalcopyrite surface would be an effective strategy to accelerate the bioleaching of chalcopyrite. In this work, using limonite as seed crystals, the effects of the goethite precipitation process on the bioleaching of chalcopyrite were studied for the first time. The bioleaching results showed that the addition of limonite controlled the redox potential in an appropriate range and promoted chalcopyrite dissolution through the removal of ferric (Fe3+) ions. X-ray diffraction and scanning electron microscope analyses indicate that limonite significantly induced the goethite precipitation process and inhibited the production of jarosite. We conclude that promoting the goethite precipitation process with limonite is an effective strategy in accelerating the bioleaching process of chalcopyrite.