Search Documents

By Peter Johnson, David Barber, Lachlan Henderson

"Within underground portions of metro rail networks the traditional approach to a design fire has been to assume a worst credible railcar fire and develop ventilation and egress measures for life safety. This approach is being challenged as a rail network approach to design fires becomes a more practical and realistic approach. The network approach is based on utilizing an in-depth hazard analysis, to understand ignition and fire load sources in tunnels, above and below the floor of the railcar and within stations, and then utilizing a quantitative risk assessment to determine sets of fire scenarios. The process allows small, medium and large fires to be considered, with the consequences also being quantified. The selection of design fires has a significant influence on fire protection measures within a metro network and hence, is a major cost input. The rail network approach provides more robust decisions on fires, based on the hazards present. INTRODUCTION A fire within a rail car or one that occurs as part of a rail system can threaten the lives of users, maintenance staff and emergency services personnel. Fires in metro systems are rare events but can have severe consequences. As a result, any analysis of a potential fire must be thorough and rigorous and address not only regular accidents and small fires, but also very low probability, high consequence scenarios. The fire safety design process for a tunnel and station must start with the design engineers, contractor and operators making a number of key decisions related to fire protection measures, which may have significant cost considerations. One of the key aspects that influences the required fire protection is the design fire and the design fire scenarios, which is a key input for analysis. This paper provides an overview of the author’s experience in designing fire protection measures for rail networks in Europe, Australia and NZ, where a risk based framework is used to develop design fires and scenarios for the whole rail system – trains, stations and tunnels. This system wide approach is innovative, challenges the norms, but provides significantly more informed outcomes. The range of design fires will include small fires that may halt the network, larger fires for smoke hazard system design and significant post-flashover fires to assess the structural response."

Jan 1, 2016

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By Bryson D. Trexler

Slope stability in open pit mines is governed by rock structure, rock quality, ground water conditions, blasting, pit geometry and excavation method. Of these factors, the control of ground water pressures often represents the primary tool to improve slope stability. Production equipment has recently been used to stabilize two slide areas by dewatering using blasthole drills for vertical holes and secondary drills for horizontal holes. This paper describes both of these dewatering programs and contrasts an earlier slope stabilization program that employed a subcontracted horizontal drill.

Jan 1, 1983

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means for controlling gases and dust. In order to study longwall ventilation in a controlled environment, researchers built a unique physical model called the Longwall Instrumented Aerodynamic Model (LIAM) in a laboratory at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) campus. LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel with a three-entry headgate and tailgate configuration, along with three back bleeder entries. It consists of a twopart heterogeneous gob that simulates a less compacted unconsolidated zone and more compacted consolidated zone. It has a footprint of 8.94 m (29 ft.) by 4.88 m (16 ft.), with a simulated face length of 220 m (720 ft.) in full scale. LIAM is built with critical details of the face, gob, and mining machinery. It is instrumented with pressure gauges, flow anemometers, temperature probes, a fan, and a data acquisition system. Scaling relationships are derived on the basis of Reynolds and Richardson numbers to preserve the physical and dynamic similitude. This paper discusses the findings from a study conducted in the LIAM to investigate the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means for controlling gases and dust. In order to study longwall ventilation in a controlled environment, researchers built a unique physical model called the Longwall Instrumented Aerodynamic Model (LIAM) in a laboratory at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) campus. LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel with a three-entry headgate and tailgate configuration, along with three back bleeder entries. It consists of a twopart heterogeneous gob that simulates a less compacted unconsolidated zone and more compacted consolidated zone. It has a footprint of 8.94 m (29 ft.) by 4.88 m (16 ft.), with a simulated face length of 220 m (720 ft.) in full scale. LIAM is built with critical details of the face, gob, and mining machinery. It is instrumented with pressure gauges, flow anemometers, temperature probes, a fan, and a data acquisition system. Scaling relationships are derived on the basis of Reynolds and Richardson numbers to preserve the physical and dynamic similitude. This paper discusses the findings from a study conducted in the LIAM to investigate the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By J. S. Peterson

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

Jan 1, 1997

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By Alena Johnson

"Much of the copper being produced today uses heap leaching, where pure metal is extracted from the ore with a chemical process rather than smelting. This technique is deployed extensively in major copper producing areas including Chile, Peru and the southwestern United States.Copper ore is excavated from the ground, crushed and then spread in uniform layers on a pad. A slow trickle of sulfuric acid is distributed over the pile, where it percolates to the bottom and a collection point. The acid leaches out the copper, along with other minerals, which can be extracted chemically. This process can be used at large sites producing 100 kt/a (110,000 stpy) and greater.Production on a massive scaleProduction at heap-leach sites is continuous and can operate on an enormous scale. The ore is fed into a crusher to break down the large pieces, and then it moves into an agglomerator to capture the fines and create more uniform particles. While in the agglomerator, the ore is mixed with acid for the first time, helping it to bind the fines into larger particles and starting the leaching process. The treated ore moves by conveyors to a stacker designed to spread it uniformly on the pad.The size of the operation comes into perspective by considering a typical pad measures 1.6-km (1-mile) long and 0.8-km (0.5-miles) wide. Working day after day, the stacker creates individual piles or modules on the pad, each 122 x 61 m (400 by 200 ft) and 3 m (10 ft) deep. When one module is filled, it moves across the pad to the next, filling the area in one continuous pile. A completed row of modules spanning the width of the pad is a cell. Once the entire pad is covered, the process begins again laying down another 3-m (10-ft) layer, and it continues until the entire pad reaches its height limit which can be several hundred feet.Once a new module is completed, technicians lay a network of plastic pipes over the surface in a pattern similar to agricultural drip irrigation installations. The diluted sulfuric acid, called raffinate, is pumped through the pipes so it can be distributed over the module, allowing the acid to soak through the ore and leach out copper as it percolates to the bottom. At the same time, approximately 35 to 45 percent of the acid is consumed by dissolving the calcite carrying the metal in the process. The raffinate reaching the bottom is now characterized as pregnant-leach solution (PLS) since it carries the copper the company is seeking to recover."

Jan 10, 2018

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to-float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in the processing of porphyry ores and treatment methods to overcome the specific problems. Though some of the problems are interrelated the problems have been classified into three broad catagories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1984

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By J. Oliver, J. Cleason

"With maintenance costs rising and an increasing demand for higher production, the use of sealed spherical roller bearings can reduce maintenance costs while providing increased production uptime. The sealed spherical bearing has increased bearing life by slowing the ingress of contamination. This paper will describe how contamination and bearing wear is reduced by reviewing case histories from coal and metal mines that improved their production by decreasing downtime using sealed spherical roller bearings. INTRODUCTION The spherical roller bearing (SRB) is a robust rolling element bearing that can accommodate high radial loads, low to moderate axial loads, and misalignment with no loss in carrying capacity. (i.e. Figure 1) Because of these characteristics, it is a favorite in mining applications and many other heavy industry applications. Primary applications are the various pulleys on conveyors. Coal and hard rock mines have hundreds of miles of conveyor lines and countless head, tail, drive, and idler pulleys. Maintaining the bearings on these pulleys and replacing bearings that have failed can be a huge expense to a mine in components, labor and downtime. Ideally, the bearings are replaced when the pulley is changed out according to the maintenance cycle, about every 4 years. Reality, however, causes the bearings to be changed out every year, or sooner. These premature bearing replacements can cause production shut downs for as long as 8 hours. Conveyor pulleys have been targeted at many mines as the single biggest maintenance pain point.The primary reason for replacing conveyor bearings is internal wear from fine, solid particle and water ingress through the bearing housing seals. (i.e. Figures 2 & 3) Traditionally, the bearing is mounted in a split pillow block housing (SAF, FSAF, SDAF or SNL are typical industry styles) with only labyrinth seals (LER/LOR) for protection against the ingress of contaminants. The bearings are lubricated with grease. A common way to extend the MTBR is to purge the bearing system with large quantities of grease to flush out the contaminants. If the bearing, and thus the housing seals are not frequently purged with grease, fine solid contaminants enter the housing and bearing through the labyrinth cavities."

Jan 1, 2015

By Alessandro Boscaro, Daniele Martinelli, Cristina Gabriela Oñate Salazar, Daniele Peila, Carmine Todaro

"The wear phenomenon in TBM machines is not a simple issue, as many parameters are playing an important role on the consumption of the tools during a tunnel excavation. The action of the wear due to the contact with the soil can occur on the excavation tools, on the cutterhead, in the excavating chamber and on the screw conveyor. The test developed at the Laboratory “Tunnelling and Underground Space Center” of the Politecnico di Torino is aimed to reproduce the interaction between the tools and the excavated material, simulating the excavation conditions in terms of soil conditioning and water content. The test, which is not standardized, is studied to evaluate the wear in a global point of view. The present work starts by testing the influence of the use of chemical agents during the conditioning phase on the drop of the wear phenomenon, in terms of metal weight loss. 1. INTRODUCTION The wear phenomenon of the excavation tools used in TBM tunneling machines is playing recently a major role in the design stage of full-section tunnels in both soils and rocks. Concerning EPB excavation technology, the main issue regarding productivity is the wear of its components (Peila et al.,2012), which increases the so called dead time in the whole process. The friction generated between the components and the ground causes the consumption of the tools and other metallic components in contact with the ground, described as primary and secondary wear by Nielsen et al. (2006a). This leads to downtime, with risky and complicated maintenance operations (Peila and Schulkins, 2009), as occurred in recent tunneling works in Liguria (Italy). The study of this argument in granular soils is very delicate, as it encloses not only the properties of the excavation tools, but also the characteristics of the ground to be excavated (hardness, mineralogy composition, shape and dimension of the particles and moisture content). The penetration mechanism is based on the scraping of the ground, by mean of cutting tools, with its consequent consumption. Concerning the rocks, the excavation principle is characterized by crushing the rock mass matrix by applying high compressive stresses through cutting disks. In such a way, to avoid frequent downtimes and their consequent economic losses, it is very important to study this subject and therefore understand and forecast the durability of the components, in order to try to maximize the productivity of the machine by reducing the frequency of maintenance stoppings."

Jan 1, 2016

By G. Guzman, L. Sevilla, M. Botz

"Newmont Mining Corporation operates the Yanacocha mine in Perú and the gold milling section of the property includes a Sulfidization-Acidification-Recycle-Thickening (SART) plant to remove copper from pregnant leach solution. Since its commissioning in 2008, the plant has been intermittently operated as needed to remove copper upstream of a carbon adsorption circuit. However, starting in 2015 Newmont expects the plant to operate on a more continuous basis in response to higher copper ores that will be processed in the gold mill. In anticipation of this, Newmont conducted a campaign in May 2014 with stockpiled high-copper ore to evaluate performance of the SART plant with elevated levels of copper in feed solution. Results from the campaign demonstrated the SART plant is capable of efficiently treating high-copper leach solution. During the campaign, leach solution copper levels ranged from about 100 to 700 mg/L, and copper removals ranging from about 56% to +99% were achieved. The median copper removal efficiency observed during the campaign was about 94%. The primary plant modification determined necessary following the campaign was the need to improve consistency with sulfide dosing. INTRODUCTION Copper removal from cyanide leach solution can be affected through the addition of sulfide at acidic pH to precipitate copper sulfide as a solid. There has been renewed interest in the process in the past several years due to the increasingly common issue of high copper levels in cyanide leach solutions. The term Sulfidization- Acidification-Recycle-Thickening (SART) is used as an acronym for the process according to the primary unit operations utilized. At a pH of approximately 4.0 to 5.0, the addition of soluble sulfide to a copper-bearing leach solution will result in the precipitation of copper sulfide (Cu2S) solid. The overall acidification and sulfidization reaction is (assuming the use of sulfuric acid for pH adjustment): 2Cu(CN)3-2 + 3H2SO4 + S-2 ? Cu2S(s) + 6HCN(aq) + 3SO4-2 The above reaction is written relative to the copper-cyanide complex 2Cu(CN)3-2, though analogous reactions also take place with the other common copper-cyanide complexes Cu(CN)2- and Cu(CN)4-3. Sulfide in the above reaction (S-2) is normally supplied as sodium hydrosulfide (NaHS) purchased in solid or concentrated liquid form. Two characteristics of this reaction that are beneficial to a leaching operation are: 1. Copper is removed from solution as Cu2S (synthetic chalcocite) solid, which can then be sold to a smelter for its copper value. 2. Cyanide that is complexed with copper in the leach solution is released as free cyanide, thereby regenerating cyanide that can be recycled to the leaching operation for continued use."

Jan 1, 2015

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By G. Keizer

Cortez Gold Mine (C.G.M.) is located in Lander County, Nevada, approximately 80 miles southwest of Elko, Nevada. It is accessed via Nevada State Highway 306 south from Interstate 80. This operation is a joint venture between Placer Dome U. S. Inc. (60% operator) and Kennecott Corporation (40%). The claims which supply oxide and refractory ore feed to the Cortez milling facility are located in both Lander and Eureka Counties. These include the Cortez and Horse Canyon deposits all operated by C.G.M. Joint Venture. Other deposits outside the C.G.M. claim area include; Fire Creek, Buckhorn, Gold Bar and Tonkin Springs. These deposits all occur along the Battle Mountain/Eureka Trend.

Jan 1, 1993

By Y. J. Wang

This paper deals with the application of linear programming to the solution of mine ventilation network problems which involve only the controlled splitting of air. An airway whose air quantity is to be controlled to a prescribed value is called a "fixed-quantity" airway. In a network where the fixed-quantity airways are increased in number and are distributed such that the air quantities for the remaining airways are uniquely determined by Kirchhoff's first law, the problem reduces to determining the head losses and locations for air regulators and fans. This is one of the network problems encountered most often in underground coal mines. By formulating Kirchhoff's second law as a set of linear constraints and the total air horsepower supplied by fans as a linear objective function which is to be minimized, the problem is analyzed through the technique of linear programming. Some important properties of the problem are discussed and examples are presented.

Jan 1, 1971

By R. K. Mehta

Existing acid mine drainage treatment techniques are not remedial In nature, i.e. though heavy metals can be removed from acid mine water, their presence in tailings and large quantities of these tailings tend to increase capital and operating cost for tailing management. This paper presents the results of a series of systematic tests which finally resulted In the development of the "ferrite" process for mine drainage of coal operations at ambient temperature. The role of pH, temperature, quantity of ferrous salt addition and degree of oxidation is investigated targeting the production of high emu spinel ferrites and effluent water complying regulatory standards with respect to Iron. manganese suspended solids and pH.

Jan 1, 1992

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015