Search Documents

By R. H. Grau, C. D. Taylor, A. L. Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Mine Improvement and New Emergency Response (MINER) Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the National Institute for Occupational Safety and Health (NIOSH) Bruceton Experimental Mine was pressurized using a 1.1-m (42-in.) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott's Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By José Maria Silva, Eugênio Oliveira, Ruberlan Silva, Thiago Souza, Lucas Reis, Lorena Guimarães, Matheus Bianchetti

Copper mine operations consistently generate a large quantity of tailings after their concentration processing. These tailings are either piled up or stored in a dam, where both alternatives of disposal lead to environmental impacts. The dam copper tailings have a huge potential for by-product production thus improving sustainability and profitability in industrial operations. This paper describes a study aiming at producing a magnetite pellet feed as a by-product from a dam chalcopyrite flotation tailings and generating free magnetite non-magnetic rougher tailings. The chemical assay and mineralogy analysis of dam copper flotation tailings indicate low Fe grade (6.34 wt%), high SiO2 grade (63.14 wt%), low magnetite (3.6 wt%), and high iron silicates content (22.72 wt%). The complex mineralogy of these tailings leads to the need of grinding the rougher magnetite pellet feed as fine as 80% of particles smaller than 20 μm ( P80) aiming at improving magnetite liberation. The proposed process route comprises a scalping screen, low field rougher, and cleaner magnetic separations using a drum magnetic separator (80 kA/m or 1000 Gauss), followed by silicates reverse cationic flotation as a recleaner step. With this process route, it was possible to produce a high-quality magnetite pellet feed reaching 68.00 wt% of Fe, 2.13 wt% of SiO2, 0.51 wt% of Al2O3, and 95.1 wt% of magnetite. The Blaine specific surface area was 2300 cm2/ g, being in the range recommended for pelletizing (1900 up to 3000 cm2/ g). The total mass, Fe, SiO2, Al2O3, and magnetite recoveries were 2.77%, 29.71%, 0.09%, 0.12%, and 73.17%, respectively. Most of the magnetite losses, around 20% of total magnetite fed, occurred in the oversize of the scalping screen. Additionally, it generated non-magnetic rougher tailings with less than 1.0 wt% of magnetite that could be used as by-products and reduced the amount of tailings disposal in a dam. This study contributes toward the sustainability of operation, minimizing tailings disposal.

Sep 28, 2022

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By Joseph Moses Botbol

Two methods are developed whereby; (1) mineralogic data can be arranged in order of typicality, and (2) mineralogic data external to a model can be compared with the model and the degrees of association computed. Thirty arbitrarily selected base metal mining districts in the conterminous United States were classified as copper, lead, or zinc districts on the basis of tonnage of the major base metal produced. For each of the copper, lead, and zinc districts binary-occurrence distributions were compiled for primary (unoxidized) and secondary (oxidized) minerals. Primary and secondary minerals were then arranged in order of decreasing typicality. Model copper districts are most typified by primary chalcopyrite, pyrite, and secondary malachite. Model lead districts are most typified by primary galena, quartz, pyrite, sphalerite, and secondary anglesite and cerargyrite. Model zinc districts are most typified by primary sphalerite, galena, pyrite, quartz, and secondary smithsonite and cerus-site. The Park City district was removed from the model and its primary and secondary mineralogy was compared with the model copper, lead, and zinc districts. The primary mineralogy of the Park City district is about equally associated with the model copper and lead districts, but the secondary mineralogy is much more akin to the model copper districts. Thus, with respect to the model data, the geochemical target presented by the Park City district resembles a copper district more closely than a lead district.

Jan 1, 1969

By Henry E. Reed

This presentation is about a small company, Industrial Mineral Products, that was formed in 1972 with one product and one customer and by a series of value-added changes avoided disaster and increased sales many times over. The principal of the company stopped by my office in Seattle looking for industrial mineral opportunities in the Northwest. We got together and went through all the minerals in Ladoo's "Industrial Minerals" from Abrasives to Zircon to see if we could find something available on the vast holdings of the Burlington Northern. At that time one of our lessees was operating a silica sand mine near Ravensdale, Washington and indicated that he might be interested in selling out. This sounded interesting to my client and within two weeks the transaction was completed.

Jan 1, 1990

By R. A. Deju

The Basalt Waste Isolation Project of the U.S. Department of Energy is a part of the National Was re Terminal Storage Program. Its mission is to assess the feasibility of siting a nuclear waste repository in the basalt formations which underlie the Hanford Site of the U.S. Department of Energy. The progress in all program areas is summarized in this paper. Activities conducted to date have led to the identification of possible repository candidate sites within the Hanford Site.

Jan 1, 1981

By Jr. Schnakenberg

In 1986 the U. S. Bureau of Mines (USBM) embarked on a major research effort to develop technology that can substantially reduce worker exposure to face hazards simply by relocating the equipment operators to an area of relative safety. This reduced exposure mining system (REMS) research effort enhances the USBM ongoing health and safety research efforts to reduce and control dust and noise and to reduce accidents through training and better mining practices. This paper reports progress of the research that is developing and will demonstrate the technologies required for the computer-assisted tele-remote operation of continuous mining machines, haulage systems, and roof bolting machines.

Jan 1, 1996

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By B. G. Stone

"INTRODUCTION “Sampling is the process of taking a small portion of an article such that the consistency of the portion shall be representative of the whole” (Baxter and Parks, 1939) “An orebody is a mixture of minerals in proportions that vary in different parts of the mass. As a consequence the proportion of contained metals also varies from place to place. Therefore, a single sample taken in any particular place would not contain the same proportion of metals as does the orebody as a whole except by a highly improbable coincidence. The probable error, which would be very large if only one sample were taken, decreases with the number of samples, but it never disappears completely unless the samples are so numerous and so large that their aggregate is equal to the orebody itself, in which case the orebody would be completely used up in the process of sampling. Since carrying sampling to such an extreme would defeat its own purpose, some probable error is always present in actual cases and the practical objective is to reduce this probable error to allowable limits. This means balancing the number of samples against the desired accuracy; if there are not enough samples the result is unreliable; if there are too many, the time and expense of taking them is excessive.” (McKinstry, et al., 1948). In an actual orebody, the accuracy of sampling depends not alone on the number of samples but also on proper distribution of them throughout the orebody, for it would obviously be incorrect to take all of the samples either in a rich part or a lean part. Therefore it is important to select the places in such a way that all parts of the orebody will be represented. “For those who cultivate land which is alike arid, heavy , and barren, and in which they sow seeds, do not make so great a harvest as those who cultivate a fertile and mellow soil and sow their grain in that. And since by far the greater number of miners are unskilled rather than skilled in the art, it follows that mining is a profitable occupation to very few men, and a source of loss to many more.” (Georgius Agricola page 5 Book 1 as translated by H.C. Hoover and Lou Henry Hoover, 1950)“It is evident that mining is very profitable to those who give it care and attention”"

Jan 1, 2015

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995

By Karin Bäppler

Hydropower produces almost two-thirds of the world’s renewable electricity generation and delivers a major contribution on the ambition of the Paris Agreement and Sustainable Development Goals (SDG) with a range of benefits to society and environment. These include clean and flexible generation and storage in addition to reduced dependence on fossil fuels and avoidance of pollutants. The Limberg III PSP is one of the European projects that addresses the implementation of the UN SDGs. The challenge of the project is the construction of a 770 m long pressure shaft to be excavated with a TBM at an inclination of 42°.

Jun 13, 2023

By E. Bloomstein

The Lone Tree gold mine is located about 4S kilometers east from Winnemucca on the west flank of Lone Tree Hill in Humboldt County, Nevada. The deposit occurs at the north end of the low, rolling Havallah Hills and is about 1 kilometer south of Interstate Highway 80, in sections 11 and 14, Township 34 North, Range 42 East, Mount Diablo Base and Meridian (Fig. 1). The Lone Tree deposit is outside of any previously established mining district and all lands are owned or controlled by Santa Fe Pacific Gold or affiliated companies.

Jan 1, 1993

By Josiah Pohl, Christopher Utter, Kyle Everly, Akshay Chowdu

Battery Electric Vehicles offer increased energy efficiency for open-pit load & haul operations at a potentially lower overall carbon cost. Electrifying a mine’s fleet, however, presents a unique set of operational challenges. In this study, we explore the effects of electrification on productivity at real operations using a Discrete Event Simulator. The model can simulate multiple shifts, a mixed fleet of diesel and electric trucks, charging and refueling stations, trolley systems, and accurate shovel-truck loading cycles. This study helps determine the trade-offs of adopting electric fleets and how they interact with the layout of today's mines.

Jun 25, 2023

By Grażyna Dzik, Adam Mirek, Krzysztof Król

The Upper Silesian Coal Basin is located in the area of the Upper Silesian Syncline and belongs to one of the most complex tectonic units in Europe. It occupies 5,650 km2. In 2020, there were 20 hard coal mines operating in the area. Seismological research in this area consists of observation of precursors/symptoms of shock generation and understanding of their effects. Studies (Teisseyre R. 1972, Mutke G. & Stec K. 1997, Stec K. 2007, Dubiński J. & other 2010, Idziak A. 2010) of complex impacts of rock mass provided a background for determining the conditions for the formation of exploitation and regional seismic shocks. Issues related to tectonic and exploitation stresses, successive extraction of coal seams at higher depths, operation in the vicinity of fault zones, often complex geological and organic conditions result in the activation of a discontinuity surface due to stress caused by deformation of rock layers, which, as a result, causes the emergence of strong shocks above 107 J. The article was based on analyses of extraction value, high-energy shocks, both of mining and tectonic-mining (so-called regional shocks) origin, against the background of changing operating conditions, which, as a result, creates an image of periodically changing seismic activity and location of strong shocks. Observation results show that, with an increase in exploitation depth and declining extraction, the number of strong shocks caused by tectonic stress (107 - 109 J) and exploitation stress (≥105 J) has been steadily increasing over the last 25 years.

Apr 26, 2022

By Daniel E. Walsh

A pilot scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2"), crushed ore from Ester Dome, Alaska. 9.04 tonnes (9.94 tons) of crushed ore were sampled and processed through a Pan-American jig -Wifley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/tonne (22.4 oz/ton). The feed grade to the plant was calculated at 1.71 g/tonne (0.050z/ton). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/tonne (0.042), 1.30 g/tonne (0.038), and 5.47 g/tonne (0.16 oz/ton) respectively. Significant, coarse, free milling gold values were shown to remain in the jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1991

By Jin Dai, Xianwen Geng, Hao Liu, Pu Wang

To investigate how deformation failure occurs in roadways surrounding rock, the relationship between cohesion and plastic shear strain of the strain softening model and the equation for calculating the shear strain of a rock mass in the ultimate elastic state are derived. On this basis, the equality relationship between the built-in maximum shear strain increment and cohesion of FLAC 3D was established to give a more intuitive picture of how the cohesion of the roadway surrounding rock changes. The cohesion attenuation and deformation of the surrounding rock are analysed. The results show that significant deformation in the roadway surrounding rock was caused primarily by the development of large areas of highly softened plastic rock masses towards residual strength. Taking the floor overhead-mining roadway under different rock pillar thicknesses (RPTs) in the Xinglongzhuang Coal Mine as an example, the results demonstrate that investigating the cohesion distribution inside the roadway during mining operation can provide a more intuitive, more accurate description of the degree of failure of the surrounding rock at any point of the roadway, as well as the overall failure range of the surrounding rock. The simulation agrees well with the field monitoring result and seems to be more practically useful than simply analysing the coverage of shear plastic zones. Based on the failure range and degree of roadway surrounding rock with different RPTs, three support schemes are designed. Classified support was implemented for roadways under different RPTs, which realizes the effective control of roadway surrounding rock.

Jan 16, 2022

By K. Johnson, B. Schiffer

Demonstrating aquifer restoration is an essential component of regulatory approval needed to mine uranium, copper, and other minerals by in-situ recovery (ISR). A PHREEQC geochemical model provided a useful means of forecasting the time for restoration and predicting future groundwater quality following low pH mining at Strata Energy’s Ross ISR Project in northeast Wyoming. The model simulated groundwater quality at three phases of the process: at the end of mining; during restoration; and post- restoration. The model utilized the one-dimensional reactive transport and dual porosity features of PHREEQC. Mineral surface ion-exchange, dissolution/precipitation reactions, and adsorption processes were simulated to estimate water quality as the pH was shifted from circumneutral to acidic during mining and back to neutral during restoration. The model results showed that cost-effective management of mine water could meet regulatory requirements. Additionally, the model was used to interpret results from a field trial and inform operational decisions. The predictive approach and geochemical understanding developed have application in assessing aquifer restoration for other ISR projects.

Mar 2, 2022