Search Documents

By William G. Pariseau

Few departments of mining, metallurgical or petroleum engineering in the United States have critical mass. Cost per student credit hour (SCH) in departments across the country are usually the highest among engineering departments, which are the highest on campus. Almost all departments are operating at fixed costs and enrollments could easily double without incurring much additional cost. However, the cost per SCH would remain unacceptably high and the probability of doubling enrollment is nil. Declining enrollment is a more likely future. The pressure to reduce SCH from university administration is unrelenting. And it has the potential for doing serious damage to program quality when standards and requirements are lowered in attempts to maintain enrollments and increase retention.

Jan 1, 2002

By Y. V. Swamy, B. Bhoi, H. S. Ray

Low-grade manganese ores with low Mn/Fe ratios can he enriched through selective carbon reduction of iron oxide to magnetite followed by magnetic separation o f the magnetite. Thermogravimetric analysis (TGA) was used to assess the preferential isothermal reduction of pure M1702 and Fe2O3 using solid carbon. This was followed by reduction of a synthetic analogue of composition comparable to an actual low-grade ore (i.e., Sandur manganese ore, Sandur, India). The carbothermic reduction of the manganese ore converts the hematite and goethite minerals to magnetite (Fe3O4), with the magnetite then going into the magnetic, fraction. The resultant nonmagnetic ,fraction becomes depleted of iron with an enhanced manganese content. These results show that it is possible to reduce the iron from 22% to 5.85%, thus increasing the Mn/Fe ratio from 1.52 to 6.2 with a manganese recovery of about 50%. The recovery was, further improved by grinding the magnetic fraction to -75 µm.

Jan 1, 1999

By M. Fan

Dry coal separation technology has particular advantages in the applications in arid and cold regions, or low rank coal separation. The hazardous pollutants in low rank coals can not be efficiently removed by conventional wet coal separation processes because a considerable amount of porose and easily friable low rank coals suffer serious particle size degradation problems in water. In this paper, a novel dry coal separation method with a vibrated air-fluidized bed of magnetic fly ash and magnetite is put forward for dry coal beneficiation. The magnetic fly ash used in this study was derived from fly ash obtained as a byproduct of coal combustion. The vibration?s effect on the uniformity and stability of a magnetic fly ash air-fluidized bed was studied. The 6×0.5 mm dry coal separation results with a vibrated air-fluidized bed of magnetic fly ash and magnetite showed that the probable error E value of separation is 0.06-0.08 t/m3.

Jan 1, 2009

By Joy Sandberg

The 1989 mining industry compensation survey done annually by the Denver-based Mountain States Employers Council shows the "average" or "typical" employee in the mining industry is projected to receive an increase of 3.9% to base pay in 1990, compared to a projection of 4.1 % for 1989. According to MSEC, the actual percentage increase to base pay has continued to decline since 1980. A review of pay increases since 1980 shows the highest average increase was 11%, granted in 1981. Since 1981, there has been a steady deceleration through the decade. While 1989 final figures are not available, 1988 numbers might indicate a reversal of this trend. In 1988, the average employee actual increase was 3.8%. That was 0.7% higher than the 3.1% projection. This may be significant as actual increases have been lower than projections since 1982. Chart A shows the pattern of projected vs. actual percent increases in pay since 1980.

Jan 1, 1990

By Peter Shuttleworth, Chris Fesq, Eddie Woods

Precast concrete segmental linings for tunnels have traditionally been designed with conventional steel bar reinforcement. In many cases, this has been satisfactory in service, but in others, major problems have occurred with the durability of the linings. Commonly this has resulted from corrosion of the reinforcement, mainly from chloridesin ground water, causing spalling of the concrete and leading to very expensive and disruptive repair programs. This paper discusses the relative merits of designing tunnel linings with steel fiber reinforcement to provide long-term durability, improved impact resistance and toughness for greater load capacity across joints, enhanced robustness during transportation and erection, plus improved fire resistance with the addition of polypropylene fibers. Guidance is also given in the selection of the correct fiber type, mix design and testing methods to establish the optimum dosage required and production techniques to ensure even distribution and compaction.

Jan 1, 2005

By K. M. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 m (1 MPa, tensile strength) into the rock mass, a distance that is sufficient to have an impact on the pitscale slope over the long term. In addition, the damage zone was calculated using the assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone — up to 2.2 m (43 MPa, rock mass compressive strength) — indicates that microfracturing can occur throughout 20-50% of the entire rock mass in the blasting area, depending on the blast geometry, burden and spacing. Finally, an economic analysis was conducted by comparing two assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond’s law after increasing the blast energy from 180 kcal/t to 350 kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. However, the benefits of blast-induced microfracturing must be balanced against the potential impacts to slope stability to ensure safe conditions, a top priority in mining operations.

Jan 1, 2014

By M. Ge

Pattison Mine is a small sandstone mine located in Iowa. The sandstones produced by the mine are not common construction and aggregate materials. The stones are used to produce a special type of sand for hydraulic fracturing, a critical technique for recovering tight gas and shale gas. These sandstones are very different from the minerals and rocks which have been studied extensively in mining. On the one hand, they are brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, they are friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, a research program was set up by the mine and Missouri University of Science and Technology. This paper discusses the preliminary results of this investigation.

Jan 1, 2012

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the USA. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before firing to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150,000 metric tons of barite in both 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender, or weighting agent in products such as paints, plastics, and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, add weight to rubber mud flaps on trucks, and add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around x-ray units in hospitals, nuclear power plants, and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses account for an estimated 78,000 tons per year in the United States. Another barite use was patented in 1926 by the oil industry. In this patent, barite is primarily used as a non-abrasive weighting agent for drilling for oil and gas exploration and production. As a weighting agent, it provides the downward force in a water based or oil based drilling fluid for cutting through rock with a tri-cone diamond drill bit. In order to minimize the wear on the drill bit and drill stem, minimum abrasion of the weighting agent is preferred. In recent years in the USA, 95% of the barite produced and about 80% on a world basis are used as a fluid weighting material during the search for oil and gas. During the latter part of the 20th century, barite was used in the drilling mud of oil and gas wells, particularly for wells deeper than 2000 meters, and petroleum well drilling demand for barite became the mineral?s major end use during economic expansions after World War II and subsequent increased use of oil and gas in the USA. The profitability of oil and gas production had a strong effect on the number of drill rigs and consumption of barite. The United States was the leading petroleum well drilling country starting in 1970, reaching 4,530 drill rigs in December 1981, and was the largest consumer of barite. In the USA, record highs of about 2.6 million tons of barite produced and 4.3 million tons consumed were reported in 1981. From 1997 to 2006, barite production declined from 662,000 to 589,000 metric tons. However, USA imports increased from 1,470,000 to 2,530,000 metric tons for lump barite. World production of barite increased from 6,780,000 to 7,960,000 metric tons during the same period. Table 1 (see Appendix) lists USA production, imports and exports and world production from 1997 to 2006. Major sources of imported barite include China, India and Morocco. Table 2 (see Appendix) lists the USA imports and price of barite by country. China, India and Morocco are the three largest exporters of barite to the USA and the world. Vietnam is a new producer, beginning in 2006. IMPACT OF CHINA ON DRILLING GRADE BARITE In the 1970s or before, China began supplying barite to the world drilling market in order to help develop their economy. When China first entered the barite export market, their high production volume, low pricing and low ocean transport expenses to the Gulf Coast forced barite producers in the USA to supply only regional markets, such as Battle Mountain Nevada barite for the western and Rocky Mountain states and Canada. Until recently, it was China?s government policy for domestic consumers to use barite below the API 4.20 specific gravity specification, leaving higher grades for export, but this is no longer the case. In recent years the internal demand for barite in China increased tremendously as their economy rapidly developed. China reduced their former 15% VAT tax rebates to 5% for Chinese barite producers, and then eliminated all VAT tax rebates on December 15, 2006. On the supply side, some high-grade barite deposits in China have been depleted. In particular, the low heavy metals sources are less plentiful. Additional mine capacity is being developed, but the new mines are underground and therefore costs will be higher. China?s appetite for other raw materials has tied up a large portion of the world?s bulk vessel fleet, including Panamax vessels (preferred for barite ore transport). Ocean transport freight rates have increased in recent years, and receiving ports in the USA are congested with imports of higher-added-value products. The Panamax Index, which tracks maritime shipping rates, more than doubled in 2006. China has also devalued its currency from RMB8.30 to RMB7.80 per dollar. These factors are driving up the import price of crude and ground barite for drilling. In addition, in the USA, rail congestion and high fuel prices led to higher trucking rates, increasing the delivered cost of ground barite to oil customers. India is the second largest supplier of crude barite to the USA and world drilling market. It produces all of its barite from a single deposit in the Cuddapah region of Andhra Pradesh State. More than 90% of production comes from the State-owned Andhra Pradesh Mineral Development Corp., and the government continues to closely control production, export volumes, and prices. India saw a dramatic increase in barite prices as a result of its last 3-year tender in 2004. However, in 2004 and 2005 their shipments of crude barite to the USA were not significant. In 2005, India began supplying barite pulverized to meet API specifications to the Gulf Coast. In 2006, Indian production was reduced owing to severe flooding in November 2005 that curtailed mining until mid-April 2006. Morocco has been the third largest supplier of crude barite to the USA and world drilling market. In 2003 and 2004 their shipments of crude barite to the USA were not significant. In 2005, Morocco resumed shipment of crude barite to the Gulf Coast and began supplying barite ground to meet API specifications to the Gulf Coast.

Jan 1, 2009

By V. Rajaram

R.C. Rex, Jr. V. Rajaram's paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude's work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 9, 1986

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

By R. Y. Wan

Acid ferric sulfate solution has been used for heap and dump leaching of low-grade chalcopyrite ores and is being considered as a possible lixiviant for the hydrometallurgical processing of copper sulfide concentrates. For many years, researchers have attempted to explain the leaching behavior of chalcopyrite, since the reaction rate kinetics are extremely slow and seem to be significantly influenced by the nature of the reaction product. A summary of conclusions drawn from reported literature on chalcopyrite leaching is found in the paper by Munoz, Miller, and Wadsworth(1) and more recently by Dutrizac.(2) Lowe(3) and Jones and Peters (4) attributed rate control to a surface reaction. Linge,(5) Dutrizac,(6) Bauer,(7) and researchers at the University of Utah(1,8) reported that the reaction rate is limited by transport in the chalcopyrite lattice or through the elemental sulfur reaction product layer. Munoz et al.(1) presented a model, derived from the Wagner theory of oxidation, which is based on the formation of a protective sulfur layer with rate control by electron transport through the insulating sulfur layer. By utilizing Wagner's parabolic oxidation relationships, (9) the following equation was obtained: [ ] where a is the fraction of CuFeS2 reacted at time t, pB is the molar density of CuFeS2, do is the initial diameter of the particle, e is the electronic charge, s is the total electrical conductivity of the sulfur layer, and ?G is the Gibbs free energy for the reaction:

Jan 1, 1984

By W. D. Hausel

Archean supracrustal rocks of the South Pass greenstone belt of western Wyoming have been the State's most prolific source of gold and iron ore. Actual gold production statistics are incomplete, but as much as 400 to 500 thousand ounces may have been mined with some silver and tungsten as a by-product. Iron ore was also mined from the greenstone belt for 22 years, and production totaled more than 90 million tons. Immediately south of the exposed greenstone belt in the Oregon Buttes area, Tertiary boulder conglomerate, which has been eroded from the granite-greenstone terrain, may contain a gold resource of 28.5 million ounces (Love and others, 1978). The amount of gold placered from stream alluvium derived from these Tertiary conglomerates is unknown.

Jan 1, 1986

By R. C. Milici

The primary factors that determine the marketability of coal from various supply centers in the U.S. are coal quality and supply; i.e. low sulfur, moderate- to high- Btu coals have large market areas when compared to less expensive but poorer quality coals. Price is the major factor in the competitive marketing of similar coal products. Good quality, (moderate- to high- Btu, low sulfur) coals from the Powder River and central Appalachian basins are marketed over large areas of the country, and central Appalachian coal is widely distributed in foreign markets, primarily as coking coal. In contrast, poorer quality bituminous coal (low calorific value and/or high sulfur) from the Illinois Basin, northern Appalachian Basin, and lignite from the Gulf Coast is marketed in or near the States in which it was mined even though the price at the mines may be lower than mine prices for central Appalachian coal. Widespread distribution of sub-bituminous Powder River Basin coal is enhanced by its exceptionally low mining costs, which offsets transportation costs to distant markets.

Jan 1, 2001

By K. Oraee

Mining Ventures are considered as high risk projects and therefore managing the risks is inevitable. Risk assessment is an important part of the complex process of risk management, hence applying appropriated and practical methods for ranking the risks associated with projects, can help to perform a better risk management. In this research the applicability of using Techniques for Order Preference by Similarity to Ideal Solution (TOPSIS) method for risk ranking in an underground mine, extracting by block caving method, was studied. Via this method, the risk associated with reserve estimation ranked as the first while in conventional method (P-I Matrix method) located in the sixteenth. Also there were significant differences in ranks of the other risks. Considering the more criteria, with different weights, in comparison with conventional methods, the results comprised from TOPSIS method are more reliable. By implementing this method risks are ranked better and more realistic and consequently then will be managed more efficient.

Jan 1, 2011

By Yang Zhao, Wanping Wang, Siqing Liu, Shuming Wen

"In China, most reserves of rich iron ores have now been depleted and sustainable development of low-grade iron ores has become a critical discussion topic in the mining industry today. The aim of this study was to evaluate the applicability of beneficiating a low-grade, hematite-magnetite ore (assaying 18.64% Fe) for subsequent utilization. In this study, process mineralogy and beneficiation of the ore were carried out in the laboratory. First, mineralogical investigation shows that the main metal minerals are hematite, magnetite and a little octahedrite that cannot be used at present, and the main gangue minerals include albite, quartz and ankerite. Based on the above, a combined process of magnetic separation and gravity concentration has been developed by using laboratory low- and high- intensity magnetic separators and a slimes shaking table, respectively. Factors affecting these separation methods are discussed, including process mineralogy on the tailings of the high-intensity separator, where the iron minerals were found to be finely disseminated in the gangue as inclusions. By applying a two-stage grinding step and a magnetic separation stage together with gravity concentration, a marketable iron concentrate assaying 60.79% Fe at a recovery of 60.23% can be obtained, when the feed assays 18.75%Fe, which provides some useful information for the sustainable use of low-grade iron ore.IntroductionIron is the world’s most commonly used metal. Steel, of which iron ore is the key ingredient, represents almost 95% of all metal used per year, primarily in structural engineering applications and for maritime purposes, automobiles and general industrial applications. By the end of 2009, the iron and steel production in China ranked the first in the world, and reached 0.567 and 0.537 billion tons, respectively. The domestic supply of iron ore was 0.88 billion tons and about 0.628 billion tons of iron ore were imported in 2009."

Jan 1, 2015

By P. J. Miranda, C. G. Anderson, L. G. Twidwell

Titanium is a metal of increasing worldwide strategic importance. The Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech of the University of Montana is currently directing two titanium research initiatives. The first program, Titanium Extraction Mining and Process Engineering Initiative (TEMPER), is focused on producing low cost titanium through the identification and development of new mining, beneficiation and extraction technologies which will significantly reduce the cost of titanium production. This will directly benefit worldwide commercial applications. Secondly, CAMP is evaluating new technologies for fabrication of titanium utilizing the Free Form Titanium Fabrication (FFTF) initiative. These technologies may drastically reduce the cost and time to manufacture titanium components. Because of the high strength to weight ratio of titanium coupled with its superior corrosion characteristics, these programs will be of vital importance to expanding the commercial and strategic applications of titanium. An overview of these two new titanium initiatives will be presented in this paper.

Jan 1, 2005

By 1980, the U.S. mining community had reached a broad consensus regarding coal pillar design. The pillar load could be estimated from tributary area theory, and the pillar strength from empirical formulas and laboratory coal strength testing. Then the growth of longwall mining required new thinking. Recently, powerful design methods have emerged from analysis of large data bases of real-world pillar successes and failures. These include the Analysis of Retreat Mining Pillar Stability (ARMPS), the Analysis of Longwall Pillar Stability (ALPS), the Mark-Bieniawski rectangular pillar strength formula, and guidelines for preventing massive pillar collapses. Sophisticated numerical models have also helped transform the pillar design landscape. In the process, our understanding of pillar mechanics has been greatly enriched.

Jan 1, 1999

By L. Zhou, L. Yuan, R. A. Thomas, D. Bahrami

The abstract emphasizes the importance of a calibrated ventilation network model for mine ventilation planning, optimization, and fire simulation. It highlights the impact of continuous airflow monitoring on improving model calibration. The paper discusses an experimental study at the Safety Research Coal Mine (SRCM) to understand the use of continuous airflow data for model improvement. It also addresses practical problems in calibration and tuning using this data, including analysis of air velocity sensor fluctuations and application of sensor location correction factors for accurate average air velocity.

Mar 7, 2022

By Massimo Concilia, Remo Grandori, Paolo Nardone

Paul Y. – SELI Joint Venture had been contracted to build the longest section of the Strategic Sewage Disposal Scheme (SSDS) – Stage I. This involved two tunnels under urban and marine areas excavated by high performance hard rock open type TBMs operated from deep shafts. A specific ground treatment program was developed using advance probing and grouting to control water inflow into the excavations. The article describes: the technologies adopted, the experienced problems, the encountered productions and their interrelation with the water inflow amounts, the possible improvement in the technologies for the excavation of the future stages of the same project as well of any other project under similar conditions.

Jan 1, 2001