Search Documents

By Y. P. Chugh

During late 2010, a scientifically founded water spray system was developed for continuous miners (CM) (Patent Pending) that reduces respirable dust exposure for miner operator by about 30%. It includes engineered sprays around the cutting drum, outer bit-ring sprays, chassis sprays and side cutter boom sprays. About 3.6 ? 4.5m (12-15 ft) behind these sprays is additional sprays that spatially cover the area between the CM chassis and the mine roof and ribs. The spray system uses approximately the same volume of water as currently used on CMs with similar operating pressures. An Illinois mine decided to implement these concepts on a CM during rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric sampling and real-time monitoring using multiple personal dust monitors (PDMs). The average results based on about 105 cuts show about 30% and 20% reduction in dust exposure for the miner operator, and the haulage unit operator. Visibility in the mining areas was also significantly improved. The coal company has already decided to implement the system on all their CMs.

Jan 1, 2012

By P. Harris, G. Groenmeyer, L. Parolis

The effect of molecular weight, charge and the presence of the cations Ca2+, Mg2+and K+ on the adsorption of carboxymethyl cellulose on pure talc obtained from Balmat, New York have been investigated. Higher adsorption densities were obtained in the presence ofCa2+ and Mg2+ ions than with K+ ions and higher ionic strength solutions resulted in higher adsorption densities. Changing the molecular weight did not influence the adsorption however increasing the charge (DS) of the polymers resulted in lower adsorption densities.

Jan 1, 2004

By M. Gomilanovic

The Republic of Monte Negro (a member of the Serbia and Monte Negro federation) has 26 different mineral raw materials, 4 of which are recoverable and 22 unrecoverable. At present, 12 types of mineral raw materials are exploited. Based on these resources more than 80 facilities were built for the production and processing of mineral raw materials. The most significant of them are coal, bauxite and decorative and technical stone. Bearing in mind that all the mentioned mining facilities have significant impact on the living environment, and that Monte Negro was declared the ecological state, the objective of this paper is to present the experience acquired from this field of science.

Jan 1, 2003

By R. K. Rajamani, A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By Earl Rau

Introduction Will cogeneration be a major power source in the future? The location of electric power generating plants has changed. In 1900, more than 50% of electricity was generated by industrial plants. Since then, industrial plant generation of electricity greatly decreased to 17% in 1950 and to only 3% in 1980. Changing economics in electric power generating costs, though, may allow cogeneration to reverse this trend. Cogeneration has been defined as the simultaneous production of electric (mechanical) and thermal energy from a single energy source. Some applications are considered to be byproduct generation of electricity from industrial, thermal operations. Cogeneration is not new to the mining and minerals industry. Smelters and steel mills have used waste heat to generate electricity. Public Utilities Regulatory Policies Act of 1978 The potential for increased industrial cogeneration of electricity is related to the March 9, 1978 enactment of the Public Utility Regulatory Policies Act (PURPA). The US Supreme Court ruled that PURPA is constitutional. The court upheld requirements that utilities interconnect to cogenerators. It also ruled that 100% of avoided costs be used as the guideline for electricity sales by a qualifying facility (QF) to a utility. The state of New York established a floor price $0.06/kWh for electricity sales from a QF to a utility. It is obvious, then, that a cogenerator must first establish price and then become a qualifying facility in order to sell electricity to a utility. Proposed cogeneration plants The estimated industrial cogeneration potential for the years 1986 to 2000 is 9500 to 25,000 MW. Industries represented in this cogeneration estimate are pulp and paper, petroleum, chemicals, food, textiles, rubber, plastics, steel, lumber and wood, cement, glass, metal fabrication, and industrial parks. A cogeneration plant has been proposed for the Union Carbide chemical plant in Institute, WV. A steam turbine/generator would be installed to replace the pressure-reducing valve in the 2.7 MPa (400 psig) header. Scott Paper Co., Mobile, AL, proposed a cogeneration plant using a coal- and wood-fired boiler and a turbine/generator to produce process steam and electric power. A cogeneration system has been proposed for a large oil refining plant. A pulverized coal boiler would produce high-pressure steam to operate a turbine, generator. The exhaust steam from the turbine will go to the process and an existing turbine. Kansas City, MO's Armour meat-processing plant has proposed a cogeneration plant. This proposal is to use a natural gas or oil-fired, gas-driven turbine and a generator. The waste heat from the gas turbine would go to a heat recovery boiler for use as process heat. Dade County, FL is implementing a central energy system to supply electricity, air conditioning, and domestic hot water for five buildings in downtown Miami. The cogeneration system is to provide flexibility, to optimize fuel use efficiency while serving the variable thermal demands. Generation of electricity from municipal waste is not considered to be a cogeneration process but is covered by PURPA. Special considerations are provided for waste/electric power generation to encourage the development of these systems. ?

Jan 7, 1987

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By J. Cole

The Morenci concentrate leach plant construction was completed and successfully commissioned in October 2007. The plant was designed to operate at medium temperature, 160ºC and pressure, 2,100 kPa. The concentrate leach plant utilized many innovative design features. This paper examines the first year?s operation, the challenges, the successes and the lessons learned. The future plans for Morenci concentrate leaching will also be presented.

Jan 1, 2009

By J. E. Dreier, R. E. Scheffel, A. Guzman

"This paper outlines a comprehensive, cost-effective testing program for the acid-ferric sulfate heap leaching of oxide, supergene and primary copper ores. It is based on extensive experience in copper heap leaching and uses the many technological advances in the field developed over the past several decades. The approach described requires firstly a detailed resource evaluation, then a hydrodynamic characterization of representative samples and, finally, a focused metallurgical testing program. The principles communicated here can be applied to other acid leachable minerals. The program varies considerably from conventional testing in its disciplined, orderly, step-by-step approach, its application of hydrological and chemical principles to leaching, and its reliance on fewer, more tightly controlled column tests. The purpose of the test program is to optimize the financial, time and other resources devoted to the program, while minimizing the financial risks to the development company or companies and the project funding providers. IntroductionThe major goal of any process development testing program should be the successful implementation of the project. With respect to heap leaching, the metallurgical testing program plays a critical role in the larger objective, as described in Scheffel (2013, 2014). McNulty’s series of papers (1998, 2004, 2014) confirm that the success of any project is directly proportional to the extent and quality of the testing program on which the process is designed.Therefore, a key development objective is to conduct a well-focused metallurgical test program. While the primary focus of this paper is copper, the acid leaching of any substance would benefit from a similar approach.This paper addresses primarily the sulfate system, which is compatible with the bioleaching of sulfide minerals. Nicol et al. (2011) described the advantages of the chloride leaching of copper sulfide minerals. United States patents Nos. US 2009/0173188 A1, US 8,597,933 B2 and US2015/0232963 A1, assigned to BHP Chile Inc. and BHP Billiton S.A. Ltd, describe methods for both the oxidative and nonoxidative leaching of primary and secondary copper sulfides. Reyes (2013) and Ipinza and Flaquer (2014) described commercial applications of chloride-based heap leaching. The testing disciplines discussed in this paper will also apply to the development of an acidic chloride leaching system."

Jan 1, 2016

By W. H. Pomroy

In its 2001 diesel particulate matter (DPM) rule for metal and nonmetal underground mines, MSHA established an interim concentration limit of 400 micrograms of total carbon (TC) per cubic meter of air (400TCµg/m3), and a final concentration limit of 160TCµg/m3, to be phased in over five years. Following a court challenge to the 2001 rule, MSHA, industry and organized labor reached a partial settlement of the litigation under which the agency agreed to issue a proposal to amend the 2001 rule by, among other things, changing the surrogate from TC to elemental carbon (EC), applying MSHA's traditional hierarchy of controls, and revising requirements for one-year special extensions for complying with the final DPM exposure limit. MSHA issued a final rule in 2005 converting the interim concentration limit from 400TCµg/m3 to 308 micrograms of EC per cubic meter of air (308ECµg/m3) based on a miner?s personal exposure. Pending further rulemaking, MSHA retained the final concentration limit of 160TCµg/m3. In May 2006, MSHA issued a final rule that clarified that the final limit of 160TCµg/m3 would be based on a miner?s personal exposure rather than as a concentration limit. The 2006 rule also phased in the final DPM limit in three steps over two years, beginning in May 2006 at 308ECµg/m3, followed eight months later in January 2007 with a limit of 350TCµg/m3, and finally reaching 160TCµg/m3 in May 2008. Also in the 2006 rule, MSHA committed to converting the 160TCµg/m3 limit to an EC limit in future rulemaking. This paper reviews the DPM exposure limits in the context of the MSHA rulemakings and discusses the DPM engineering controls that were utilized by mine operators to attain compliance with each progressively lower limit.

Jan 1, 2009

By J. Z. Cheng

The extraction of thorium from industrial radioactive wastewaters discharged from Rare Earth (RE) plants was studied by the liquid membrane emulsion technique using P507- Span80-sulphonating kerosene-HCl. The emulsion conditions, the technological factors such as ratios of oil to the internal aqueous phase and water to emulsion, and the extraction time etc. were investigated.

Jan 1, 2008

By P. Lopez, E. Wellman, N. Risso, A. Anani

Current machine learning models used for roof fall hazard prediction are mounted on expensive sensors, computationally expensive, or lack the robustness for accurate prediction in the underground mining environment. This research aims to provide a design methodology for a robust, low-cost, deep learning-based algorithm for underground mine roof fall hazard prediction. A data sampling plan is developed to ensure the replicability and robustness of the developed model. In addition, feature engineering and transformation methods are described to identify relevant features for hazard identification. The methodology described here will be used in model development, tested, and implemented as a real-time mobile device application. The new tool will be expected to detect roof fall hazards in real-time and contribute to a crowdsourcing approach for underground hazard detection.

Feb 1, 2023

Instabilities occurred as a result of climate changes caused to investigate the rock behavior dependency to temperature changes, in this paper. In the natural earth condition, the phase transition of pore water has known to be the most effective factor causing different rocks mechanical properties due to temperature changes. So, the temperature range of [-30, 30]°C is selected in laboratory tests of this study. P-wave velocity, unconfined compressive strength (UCS) and elasticity modulus of rocks at different temperatures are studied by developing a temperature adjusting apparatus. The tests were performed on three rock types. The results show that firstly, the temperature reduction and pore fluid freezing improves these rock?s mechanical properties. Secondly, the dependency of rock properties to climate changes depends on the type and shape of its porosity as well as porosity percent. The improvement of rock mechanical properties in jointed rocks exceeds rocks with spherical pores. Finally, maximum changes in rock?s properties occur at [-10, 0]°C, which includes the phase transition of pore fluid. Keywords: Temperature; Rock Mechanical Properties; Pore Fluid; Porosity.

Feb 27, 2013

By Y. Nien Wang

The Devil?s Slide portion of Highway 1 between Pacifica and Montara is often closed due to the instability of the adjacent slopes. Following many years of public input and careful evaluation of alternatives, Devil?s Slide will be by-passed via two inland tunnels, providing a safe, dependable highway between Pacifica and Montara. For the twin tunnels, each 9m diameter tube will accommodate only one traffic lane. Each tunnel tube will accommodate a 3.6 meter roadway, 0.6 meter and 2.4 meter inside and outside shoulders respectively, and 1.2 meter walkways on each side. Cross passages will connect the bores at about 120 meter intervals and jet fans will provide tunnel ventilation. The twin tunnels are approximately 1,250 meter long and 9 meter wide. Excavation will progress from south to north using tunneling techniques that rely on inherent rock strength for support known as the New Austrian Tunneling Method (NATM). Both tunnels will be excavated at the same time, one tunnel face approximately 40 meters ahead of the other. Staggering the tunnels reduces the likelihood of damage from blasting in alternate tunnels. The work schedule is 24 hours a day, 7 days a week resulting in a 24-month timetable to break through to the north portal.

Jan 1, 2008

By W. G. Pariseau

This contribution focuses on the role of stress analysis for mine planning and the selection of suitable computer programs for the task with special emphasis on coal mine pillars. In this regard, barrier pillars that defend a set of five main entries at the Crandall Canyon coal mine in central Utah were formed during extensive longwall mining north and south of these main entries. Numerical analysis for ground control guided the mine planning and permitting. Retreat mining of pillars led to disastrous events August 6 and 16, 2007, with the loss of nine lives. A most difficult lesson taught by the Crandall Canyon tragedy is the need for education in the selection and use of computer programs for pillar design. Much of this contribution is taken from a report prepared for the Mine Safety and Health Administration (Gates, et al, 2008). Details appear in Appendix Q of the report (Pariseau, 2008). The Crandall Canyon mine is about 16 miles west of Huntington, Utah, in the Wasatch Plateau coal field. Geology of the Wasatch Plateau is described by Doelling (1972) as gently dipping Cretaceous sandstones, mudstones, coal seams, and shales. Joint systems are present in strata above and below coal seams where cleat systems are present as described by Hucka (1991). Several major fault systems transect the field and form grabens with 450- 760 m of drop. One such structure is Joes Valley fault that crosses the Crandall Canyon mine. Mines in the Wasatch Plateau are generally developed from outcrops in steep canyon walls. Overburden increases rapidly as mining progresses into the plateau; mining depth varies with topography between 450 and 600 m in the region of interest. A stratigraphic column derived from a borehole into the mine is shown in Figure 1. There are 11 layers in the column.

Jan 1, 2011

Lime production is the largest single chemical use for limestone and dolomite. The term “lime” in this review refers to high-calcium and dolomitic quicklime, their hydroxide forms and dead-burned dolomite. This review is restricted to a discussion of the U.S. lime industry. Production and consumption In 2004, according to preliminary data, U.S. lime production was about 20.1 Mt (22.1 million st), an increase of 900 kt (990,000 st) compared with 2003. Production in2004 was valued at about $1.4 billion. Commercial sales of lime totaled 18.6 Mt (20.5 million st) and captive production was 1.5 Mt (1.65 million st). Total U.S. consumption was about 20.2 Mt (22.2 million st). The majority of U.S. lime trade was with Canada.

Jan 1, 2005

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993

By D. Richers

When modeling predictive pit lake chemistry, groundwater chemistry is integrated with the affected portions of the wall rock and chemistry of the lake in a complex series of mixing. Fractions of the solutions impinge upon fresh, unaltered or fractured and oxidized zones of the wall containing sulfide materials and/or soluble metal/metalloid salts. Changing conditions over the short term (biannually) and long term (decades) can drive reactions allowing for dissolution or precipitation of acid rock drainage and metal leaching (ARD/ML) constituents. Local zonal variations can result in a portion of the pit releasing materials into solution; whereas other portions of the lake might favor the formation of colloids or precipitants. The proportions and character of groundwater can drive the chemistry of the pit lake provided sufficient buffering capacity is available to temper the generation of ARD in the system. For sulfide-rich systems, reduction of oxygen by rapid inundation and consumption by sulfides is key to reducing the ARD/ML. This paper presents several models of a sulfide-rich wall rock system using a range of groundwater chemistries to show these constraints.

Jan 1, 2012

By B. K. Belle

The beginning of 21st century has heralded the global strategic importance, as evidenced by increase in energy prices and energy generation-emission-utilization dilemmas. In January 2008, the South African energy supplier, ESKOM had tabled the concept of power conservation and acknowledged the energy crisis until 2016. The concept is required of all energy users to reduce their electricity consumption, intensify energy efficiency and cautiously proceed with new projects. The generation of energy results in by-products called ?green house gases? (GHGs). To make a positive response to climate change and their effect on the environment, every energy user must ensure efficient energy use through technical and administrative means referred to generally as energy savings. This paper identifies mine ventilation engineering, in particular the electricity consumed by main fan units, as an area of potential energy savings. For a major mining company, electricity consumed by main ventilation fans alone can be in the order of 120 MW. Although a known fan engineering technique but scantly applied technology identified as the Hermit Crab can be seen as a ?quick win? project, due to its success in other industries such as cement and steel. The ?Hermit Crab? technique® involves upgrading or replacement of an impeller - whatever its origin - with a design impeller to suit the actual ventilation requirements, resulting in increased fan efficiencies. The cash flow benefits associated with a case study and its rollout of this technology have been calculated. For a 10% increase in main fan efficiency, would have a net present benefit of US$ 16.08m over 10 years. With the inclusion of carbon credits, this benefit rises to US$ 29.40m in total. Application of other available technologies, viz., composite materials, ventilation-on-demand and variable speed drives are discussed.

Jan 1, 2009

By K. Oraee

Rate of penetration of Tunnel Boring Machines (TBM) has a significant role in the planning, measurement of productivity and performance of any tunneling project. In this paper, the application of Adaptive Neuro Fuzzy Inference System (ANFIS) in prediction of TBM penetration rate is evaluated. For this purpose, a database including Rock Quality Designation (RQD), Uni-axial Compressive Strength (UCS) of the rock, the Distance between Planes of Weakness (DPW) in the rock mass, and empirical data regarding rate of penetration of TBM from several tunneling projects are collected. The Rate of Penetration is then estimated by using ANFIS. These results are then compared with measured TBM penetration rates (actual data). It is concluded that ANFIS can be applied successfully for such purpose and result in high accuracy for prediction for the rate of penetration of TBM. The method provided in this paper can assist the mining engineer to estimate the performance of tunneling accurately.

Jan 1, 2012