Search Documents

By J. J. van Vuuren

Pipe-stick support in deep-level gold mines is first described and illustrated, a pipe-stick being a mine pole trimmed to the required size and sleeved by a pipe. An account is then given of an investigation into this form of support that involved load-compression tests in a 1000-ton press, tests in a rapid loading machine simulating rock-burst conditions, a study of the load-compression behaviour of pipesticks installed underground, and a cost evaluation. Pipe-stick support was found to be very effective on the face and to cost less than conventional matpacks.

Jan 1, 1979

By I. H. Clark

In some mining situations, backfills are not only required to be free-standing but are also expected to provide hangingwall support. It may therefore be specified that the backfill withstand a certain calculated stress within a given time. Given the materials available, the choice of backfill composition is not always straightforward, and an approach to the evaluation of cemented tailings backfill is therefore proposed. The general use of such a method will greatly assist in both the scientific analysis of the material properties for industry-wide purposes of comparison and decision-making as regards the choice of fill.

Jan 1, 1988

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

By P. Beukes, D. Bessinger, R. Glenewinkel

High titania slag is produced by the smelting of ilmenite and a suitable carbonaceous reductant in electric furnaces. Currently liquid slag is cast into large blocks, which take about 10 days to cool down before they can be crushed, milled and classified into two final products. The two products, chloride and sulphate grade slag, are differentiated according to their size. Granulation of titania slag has been identified as a possible alternative to the conventional block route. This paper discusses some of the work carried out at Exxaro Research and Development to investigate both wet and dry granulation of titania slag.

Jan 1, 2007

By M. K. Matthews

The use of backfill has important environmental control implications which, although frequently overlooked, can be both beneficial and problematical. Where backfill is widely used, the reduction in stope heat load and improved air utilization influence the overall mine ventilation and refrigeration requirements significantly. A programme of work examining in detail all the environmental consequences of backfilling is currently underway at the Environmental Engineering Laboratory of the Research Organization of the Chamber of Mines. This paper gives an overview of the work and presents some findings. In so doing, the environmental implications to be considered when backfilling are highlighted.

Jan 1, 1988

By S. J. Patchet

The use of fill in deep-level gold mining presents the possibility of achieving considerable economic and operational benefits if conventional support can be eliminated. Unfortunately, the combination of the properties of tailings from gold reduction plants and the narrow, flat, tabular reefs being exploited make conventional hydraulic filling very unpractical. Laboratory tests indicate that, with careful control of water content, these tailings can provide an adequate fill material. A variety of bonding agents have been investigated, and the most practical seems to be ordinary Portland cement. Even at very low cement contents some cohesion is achieved. The design and layout for a complete fill support system using hydraulic transport, dewatering, and pneumatic placement are discussed, and a surface field trial indicated that the principles involved are correct and that acceptable results can be achieved. This system and material would completely eliminate conventional timber and brick support, and a preliminary economic analysis indicates that filling is cost competitive on a direct replacement basis. All the operations for a full-scale operation are available or have been developed to a stage sufficient to indicate that the system is practical, although certain operations require further refinement.

Jan 1, 1978

By A. S. Macfarlane

Western Deep Levels (North) is a deeplevel, longwall gold mine. Severe strata control problems and high rates of elastic closure, resulting in high rates of energy release, are associated with mining at depths of up to 3 500 metres. To assist in controlling these aspects of mine design and safety, a waste backfilling system has been designed and commissioned. The integration of such a system into an existing, producing longwall brings many problems of logistics, organization, planning and control. It is the purpose of this paper to examine these aspects of fill management, and to describe some of the practical problems involved with the integration of this project into the mining environment. Although many of the rock mechanics and soil mechanics aspects of backfilling systems are common there are specific problems involved which apply to longwall systems. Very strict guidelines are required for planning personnel to design their backfilling systems for a particular situation. These aspects are examined, and basic models developed which can be used without the necessity of comprehensive input from rock mechanics. A summary of the financial implications is included, and these are examined with regard to possible future applications and expansion of waste filling.

Jan 1, 1988

NIM reports Report No. 1615 Fluorspar pellets. A survey of the world market and an assessment of future South African production. Report No. 1621 Correction for matrix effects in the analysis of solutions by X-ray-fiuorescence spectrometry. Notices Questionnaire on Technicians The Department of National Education's committee of enquiry into the education, training, utilization, and status of engineering technicians in the Republic of South Africa was established as a result of Resolution 6.3 taken at the Sixth Conference on Engineering Education: The Education and Training of Engineering Technicians. Vraelys oor Tegnici Die Departement van Nasionale Opvoeding se komitee wat ondersoek instel na die opleiding, gebruik en status van ingenieurstegnici in die Republiek van Suid-Afrika is gestig as gevolg van Besluit 6.3 wat geneem is tydens die Sesde Konferensie oor Ingenieursopleiding: Die Opleiding van Ingenieurstegnici. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute.

Jan 8, 1974

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

Notices TRANSPORTATION AND THE ENVIRO NMENT The 5th Quinquennial Convention of the S.A. Institution of Civil Engineers will take place at the Carlton Centre, Johannesburg, from 20th to 24th August, 1973. ENVIRONMENTAL ENGINEERING A conference on environmental engineering problems in industrialized and developing countries is to be held at the United Engineering Centre, New York, on 19th and 20th September, 1973. RABCEWICZ-COLLOQUY The Austrian Society for Geomechanics is to honour Professor Ladislaus V. Rabcewicz, on the occasion of his 80th birthday, with a meeting in Salzburg Congress Hall on 11th and 12th October, 1973. The themes of the four half-day sessions will be as follows. PYRO MET ALL URG ICAL EVENTS IN 1974 Diisseldorf is to be the venue for the following three events: International Iron and Steel Congress O.F.S. Branch Welkom THE MARCH GENERAL MEETING OF THE BRANCH WAS HELD IN THE ST. HELENA CLUB AT 8.00 P.M. ON TUESDAY, 6TH MARCH, 1973 O.F.S. Branch Welkom MINUTES OF A GENERAL MEETING HELD IN THE ST. HELENA CLUB ON WEDNESDAY, 16TH MAY, 1973, AT 8.00 P.M.

By H. S. Sichel, Kleingeld

A frequency distribution model plays a fundamental role in ore evaluation, especially for the feasibility study of new deep gold mines. The geological complexity of the reefs being mined at present in the Witwatersrand basin poses some difficulties regarding the modeling of the underlying ore-value distribution. This geological complexity has given rise to a need for more applicable distributional models. This paper places the geology of the Witwatersrand basin in perspective and draws some important conclusions from the genesis of the deposition. In addition to the three-parameter lognormal model, two more-general distributional models are proposed. These are the compound lognormal (CLD) and log-generalized inverse Gaussian (LN-GIG) distributions. A detailed, although preliminary, comparative study of these two more-general models with the three-parameter lognormal model is described, and the efficiencies of the estimates and modeling are analysed. It is found that the broad assumption that gold grades follow a three-parameter lognormal law is not always the case, and the need to test for departures from log normality should be emphasized so as to ensure the use of appropriate models.

Jan 1, 1992

By Austin Whillier, Duncan Mitchell

The problem of heat stress underground in the gold mines is approached on the basis of the heat transfer between the human body and the underground environment. Experimental measurements of radiant and convective heat transfer and a theoretical calculation of maximum evaporative heat transfer enable the maximum cooling power of an environment to be calculated in terms of the dry-bulb and wet-bulb temperature, the mean radiant temperature, the wind speed and the barometric pressure. For most underground applications the cooling power can be expressed as a function of wet-bulb temperature and wind speed only. The relative importance of wind speed and wet-bulb temperature can be assessed: in working places where wind speed is low additional cooling of workmen can be achieved better by increased wind speed than by decreased wet-bulb temperature. The wet kata reading proves to be of limited value as an index of heat stress because environments with equal wet kata do not necessarily have the same cooling power. Finally, thermal equilibrium with the environment is possible when cooling power equals or exceeds the rate of metabolic heat generation. The rates of metabolic heat generation for various underground tasks are indicated.

Contribution by G. Narsimhan It was with much pleasure that I went through D.F. Malan's excellent paper. The following explanatory and critical note has been the result of my deep study of the paper. Although by qualifications and experience I have been a chemical engineer, involved over four decades with problems in the modeling and simulation of transport-limited (heat and mass) chemical reactions in multi-phase systems, I have of and on interested myself in challenging problems in extractive metallurgy. This is the first time I have veered of to continuum mechanics, at the age of 71! Author's reply. I thank Professor Narsimhan for his extensive contribution to the paper. It provided me with the stimulus to derive an extended model. However, there are some inaccuracies in his arguments that need further discussion. Professor Narsimhan's main concern is that there is not a good enough fit between the derived viscoelastic Kelvin model and the experimental data supplied by Güler1 (see Figure l1 on page 218 of my paper). I will therefore explain the choice of a viscoelastic model in more detail and also make specific comments on the arguments given in his contribution.

Jan 1, 1996

By Isobel Clark

This paper reviews some of the traditional methods of reserves estimation based on lognormal distribution with or without an additive constant. In the rush to computerize mine planning and grade control generaly, proven estimation methods, such as Sichel's t, seem to have been overlooked. By use of a personal microcomputer, the traditional methods were investigated thoroughly, the results being tested against existing tables and figures. The fitting of a lognormal distribution, including estimation of the additive constant, is discussed, and the calculation of Sichel's t estimator and its associated confidence limits is described in detail. Payability calculations for a lognormal distribution are also covered briefly. The advantages of personal computers, particularly speed and ease of use, are emphasized. This low-cost approach permits detailed investigation of some of the assumptions and approximations inherent in the established methods of calculation. Several disturbing discrepancies are revealed in various factors, and some generalized statements made by previous authors are found to be over-simplistic. Full details are given of acceptable approximations and computer algorithms, and concern is expressed over the possible loss of proven methods under the welter of new, sophisticated computer software.

Jan 1, 1987

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

By J. P. Hugo

Nuclear energy - its interactions with mining and metallurgy - PRESIDENTIAL ADDRESS given by J. P. Hugo Pr. Eng., B.Sc (Eng.) (Rand), Ph.D. (Sheffield) Energy is the life blood of the modern technological era in which we live and it was, I think, Benjamin Franklin who said that the manipulation of energy was the basis of all science and technology. This is perhaps an oversimplification, but there can be little doubt that our life today, and the improved standard of living we aspire to, are governed almost entirely by our ability to generate and manipulate energy. This ability has made it possible for Man - each specimen a feeble twentieth of a horsepower - to travel to the moon, to recover valuable minerals from the depths of the earth, to do arithmetic at unbelievable speed, to lessen the drudgery of manual labour. For these and virtually every aspect of our life we are dependent on energy from external sources. It is, therefore, not surprising that the per capita consumption of energy, and more particularly electricity, has become one of the most reliable criteria by which to measure the standard of living and technological advancement of a country.

By A. J. Lynch, N. W. Johnson, D. J. McKee, G. C. Thorne

The behaviour of minerals in sulphide flotation processes, with reference to simulation and control. by A. J. LYNCH, Ph.D., N. W. JOHNSON, Ph.D., D. J. McKEE, Ph.D., and G. C. THORNE, B.Sc. (Hons.) (Visitors) In sulphide flotation processes, there are two mechanisms by which particles are transferred from the flotation pulp to the concentrate: adhesion to air bubbles and natural flotation, and entrainment in the froth. The entrainment mechanism is particularly important for particles of non-sulphide gangue, which do not absorb collector. The importance of controlling the recovery rate of water was illustrated in plant testwork in which selectivity between valuable sulphides and sulphide gangue, and between valuable sulphides and non-sulphide gangue, was altered by manipulation of variables affecting the water recovery rate. The two mechanisms should be recognized in the development of a control system. Most of the control schemes in operating plants have concentrated on reagent additions, which affect the natural flotation mechanism. Although control of the chemical environment is clearly of paramount importance in flotation, plant tests have shown that control of the variables affecting the entrainment mechanism is also important.

Jan 4, 1974

By R. Sun, R. G. Gillies, R. S. Sanders, J. Schaan

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is abetter indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By D. Seke

Metal inventories are usually reported in financial statements of mining companies. However, the value of these inventories can be reliable only if the metals in stock are measured within acceptable tolerances. Reliable metal balancing requires accurate mass measurement, sampling, and chemical analysis. Many mining companies are usually unable to validate the accuracy of metals in inventories at the end of their financial year. This is mainly due to poor mass measurement, sampling, and chemical analysis practices. This has an adverse impact on metallurgical accounting and metal valuation. In addition, it puts a lot of stress on external auditors, who have the duty to recommend the approval of the financial statements to the board of directors. Although a full value chain of metal reconciliation includes the accuracy of Mineral Reserve definition and grade control at the mine, this paper discusses the implementation of best practices for mass measurement, sampling, and chemical analysis at processing plants. This is an important aspect of sampling and reconciliation that is required in order to improve the reporting of inventories in the financial statements of public mining companies. Keywords metallurgical accounting, corporate governance, sampling, analysis.

Jan 1, 2014

A banquet, attended by 467 members and visitors, was held at the Wanderers Club, Johannesburg, at 8 p.m. on Friday, 21st March, 1969, to celebrate the 75th Anniversary of the founding of the Institute. Introduction of Dr Carel de Wet R. C. J. Goode (President) Dames en here: Ons het 'n aantal vooraanstaande gaste in ons midde vanaand en mnr Maxwell sal u later meer van hulle vertel. Dit is my aangename plig om u voor te stel aan sy Edele, die Minister van Mynwese, van Beplanning, en van Gesondheid, Dr de Wet en sy gade, mev de Wet. Sy Edele Dr de Wet het geen bekendstelling nodig nie-alhoewel hy ons minister vir slegs die afgelope twee jaar is, het hy reeds talle funksies van ons Mynbedryf bygewoon en het baie vriende gemaak onder ons. Hy het homself baie bemind onder ons gemaak toe hy Wes-Driefontein onlangs besoek het om hulle ondersteuning en aanmoediging aan te bied in hulle uur van nood. The Honourable Dr de Wet was born in the Free State. He is a grandson of that very famous general Christiaan de Wet, who caused so much pain to the British forces and for so many months so successfully eluded them in the Transvaal and Orange Free State. He was educated at both the Pretoria and Witwatersrand Universities. He first practised medicine at Boksburg and then moved to Vanderbijlpark, so you see he has an early association with gold mining on the Witwatersrand, and in moving to the Vereeniging-Vanderbijlpark district he became closely involved in our coal mining and metallurgical industries. South Africa's first steel was poured from a l0-ton open hearth furnace belonging to the Union Steel Corporation in Vereeniging in 1913. Dr de Wet has been mayor of Vanderbijlpark and for several years has been their member of parliament. More recently, the Honourable Dr de Wet has filled with great honour that most important office of Ambassador for the Republic of South Africa in London. At present he wears two hats, in that he is Minister of Planning and of Health, but more important is his cloak, that of Minister of Mines, which I trust offers him the greatest comfort. To fulfill these three arduous tasks must demand of him a terrific devotion to duty, and in doing this he carries on that loyal tradition of service to his fatherland so evident in his grandfather. Dames en here, dit is vir my 'n groot genoeë om Sy Edele Dr de Wette vra om 'n heildronk in te stel op die Instituut vir Mynwese en Metallurgie. Toast to the Institute of Mining and Metallurgy Dr the Honourable C. de Wet (Minister of Mines): Mr President, ladies and gentlemen, Mr President you have introduced me gracefully to this distinguished company and I am appreciative of your remarks. I am fully conscious of the responsibilities that devolve upon me as Minister of Mines in a country where mining makes so vital a contribution to economic progress and development and has, in fact, laid much of the foundation on which our present proud edifice is built. The achievements of the mining and metallurgical industry in its diversified activities arouse feelings equivalent to paternal pride, but let me speedily add that in considering any family relationship that may exist, the Minister of Mines should not be regarded in the role either of a fairy godmother or an indulgent father.