Search Documents

By A. F. Collings

The processing of heavy mineral concentrates can be enhanced by the use of power ultrasound to clean their surfaces of oxidation products and fine coatings, mainly through the large, but very localized forces, produced by cavitation. Results are presented of the application of power ultrasound to remove coatings from the surfaces of mineral sand concentrates in order to improve the sharpness of their high-tension separation and, in some cases, the quality of the low iron components such as zircon. Improvements of 10–15% in recovery and up to 20% in grade compared to unsonicated material were achieved in a single stage laboratory high-tension separation. Cavitation also ensures that a fresh, clean surface is presented to leachants during the leaching of suspended solids. At the same time, the effect of cavitation and the shearing effect of the sound wave passing over the solids ensure that the saturated boundary layer is kept to a minimum if not completely removed. This application of power ultrasound helps to speed up leaching processes as applied to the removal of excess alumino-silicate contaminants in some ilmenite. Keywords: Ultrasound, power ultrasound, heavy minerals, processing.

Jan 1, 2003

By A. Haines, O. Varaud, I. Baidoo

Abosso Goldfields Limited (AGL) is in the process of developing an expansion of their Damang Open Pit gold mine in Ghana. AGL acquired the Damang mine in January 2002, with SRK participating in the geotechnical investigation and design for the project since 2001. A deep resource drilling program, completed during 2004, intersected an extension of the orebody below the then planned final pit floor. A feasibility study has been completed to determine the economic extraction of this deep ore with an expanded pit shell. The Damang mine is in a stockwork sulphide deposit at the culmination of the Damang anticline. The deposit occurs as hydrothermal mineralisation associated with dominantly east dipping thrusts and sub-horizontal quartz veins. Primary gold mineralisation also occurs in the conglomerates of the Tarkwaian Formation. The geological units consist of steep easterly dipping dolerite, sandstone, siltstone and phyllite beds, with the weathering profile comprising saprolites overlying a relatively thin joint oxidized horizon. It is planned to deepen the current open pit to a final depth of up to 270 m, primarily by the development of a push-back of the eastern and western walls. The edge of the Eastern Tailings Storage Facility (ETSF) is currently located within 80 to 100 m of the crest of the existing pit. The geotechnical design focused on the optimization of the bench face angle and finally recommended a ?Steep Slope Strategy?, involving 24m high near vertical benches. Limiting bench stack heights of 96m at a maximum of 66° were derived from the influence of major structures and the variation in rock mass conditions. The overall slope angles in each pit sector were developed around the requirement for haulage ramps. One of the main design challenges was to optimise the standoff distance between the final pit crest and the ETSF. This process had to consider maximum access to the resource without undue influence on or from the nearby tailings dam. A planned increase to the height of the dam wall was an additional factor in the design. Dewatering of the pit walls was also a major consideration in this tropical environment.

Jan 1, 2006

By P. Sun

Abstract: From the viewpoint of interaction mechanics of solid and gas, a coupled mathematical model is presented for coal/rock mass deformation and gas leak flow in parallel deformable coal seams. Numerical simulations for the prediction of the safety range of mining of protection layer are performed with experimental data from a mine with potential danger of coal/gas outbursts. Analyses show that the numerical simulation results are consistent with the measured data on the spot. Therefore, the coupled model shows a positive future for applications in a wide range. ZUSAMMENFASSUNG:Von der Veranschaulichung der Abhängigkeit Mechaniker für Körper und Gas, wird ein verbundenes mathematisches Modell für festen coal/rock Deformation und Gasleckstelle Fluß in parallele deformable Kohlenähte dargestellt. Numerische Simulationen für die Vorhersage der Sicherheit Strecke, die Schutzschichtbergbau verwendet, werden mit experimentellen Daten von einer Grube mit möglicher Gefahr der coal/gas Ausbrüche durchgeführt. Analysen zeigen, daß die numerischen Simulation Resultate mit den gemessenen Daten bezüglich des Punktes gleichbleibend sind. Folglich zeigt das verbundene Modell eine positive Zukunft für Anwendungen in einer breiten Strecke. RÉSUMÉ: Du point de vue de la mécanique d'interaction pour le solide et le gaz, un modèle mathématique couplé est présenté pour l'écoulement plein de déformation de coal/rock et de fuite de gaz dans les filons houillers deformable parallèles. Des simulations numériques pour la prévision de la gamme de sûreté employant l'exploitation de couche de protection sont effectuées avec des données expérimentales d'une mine avec le danger potentiel des accès de coal/gas. Les analyses prouvent que les résultats numériques de simulation sont conformés aux données mesurées sur place. Par conséquent, le modèle couplé montre un futur positif pour des applications dans un éventail.

Jan 1, 2003

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By I T. Tshabalala

In typical conventional narrow vein stoping operations, the use of temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The authors wishes to explore the probability and practicality of making use of new generation support products to make the support operations safer as well as enhance productivity in the stope face. This paper will examine the use of Autorock Drills as a means to drill roof support holes and install appropriate support components into these holes, as well as the application of ?Thin Spray Liners?, commonly called TSL?s as an additional means of creating a safer operating environment. The installation of netting as a means of roof protection and other support aspects such as cemented roof-bolts will also be explored. These proposed items are envisaged to improve the safety of our people and reduce production down time and increase production and productivity.

Jan 1, 2008

By M. Hakala

A computer program was developed to simulate transient strains and stresses during an overcoring in the situ stress measurement. The solution is based on superpositioning of elastic stresses. The measured strains can be compared with the calculated ones to check if the measured transient behaviour is accordant with the interpreted in situ state of stress. If not, the in situ state of stress can be calculated based on any transient or final strain values. The transient stresses can be compared with the strength envelope of intact rock and thereby estimate the core damage potential. Technically, the developed code fulfilled all the objectives, and the numerical error was found to be less than 5%. The basic idea can be applied also for different overcoring probes with minor modifications and recalculation of stress tensors. The analysed case studies showed clearly the advance of having an objective and practical quality control method to study the reliability of the in situ stress measurement data. The study was set up and funded by the nuclear waste management companies Posiva Oy ( Finland ) and Svensk Kärnbränslehantering AB ( Sweden ). Un programme informatique a été développé pour simuler des tensions et des contraintes passagères pendant la mesure in situ de contrainte de surcarottage. La solution se fonde sur une superposition de contraintes élastiques. Les contraintes mesurées peuvent être comparées avec celles calculées pour vérifier si le comportement passager mesuré correspond à l'état de contrainte in situ interprété. Sinon, l'état de contrainte in situ peut être calculé à partir de n'importe quelle valeur de contrainte passagère ou finale. Les contraintes passagères peuvent être comparées avec l'enveloppe de force de roche intacte et ainsi il est possible d'évaluer le potentiel de dégâts au noyau. Techniquement le code développé a rempli tous les objectifs, et le taux d'erreur s'est révélé être inférieur à 5 %. L'idée de base peut être appliquée aussi pour différentes expériences de surcarottage avec des modifications mineures et le recalcul de tenseurs de contrainte. Les études de cas analysées ont montré clairement l'avantage d'avoir une méthode de contrôle de qualité objective et pratique pour étudier la fiabilité de données de mesure de contrainte in situ. L'étude a été fondée et financée par les sociétés de gestion de déchets nucléaires Posiva Oy (Finlande) et Svensk Kärnbränslehantering AB (Suède). Es wurde ein Computerprogramm entwickelt, um Transient-Beanspruchungen und Spannungen während eines Überentkernens in situ-Spannung-Messung zu simulieren. Die Lösung beruht auf Superpositionierung von elastischen Spannungen. Die gemessenen Beanspruchungen können mit den berechneten Daten verglichen werden, um nachzuprüfen, ob das abgemessene Transient-Verhalten mit dem interpretierten in situ-Zustand der Spannung übereinstimmt. Wenn nicht, kann der situ-Zustand der Spannung auf irgendwelchen Transient- oder endgültigen Beanspruchungswerten berechnet werden. Die Transiet-Spannungen können mit dem Stärke-Umschlag des intakten Felsens verglichen werden und dadurch ein Kernbeschädigungspotential kalkulieren. Technisch erkannte der entwickelte Code alle Ziele und hat gefunden, dass die numerische Fehler weniger als 5 % waren. Grundsätzlich können auch verschiedene Überentkernen-Untersuchungen mit kleineren Modifizierungen und Wiederberechnung des Spannung-Tensors angewandt werden. Die analysierten Fallstudien zeigten deutlich den Fortschritt, objektive und praktische Qualitätskontrollmethode zu haben, die Zuverlässigkeit in Situ-Spannung-Messung-Daten zu studieren. Die Studie wurde aufgestellt und durch Atommüll-Management-Firmen Posiva Oy (Finnland) und Svensk Kärnbränslehantering AB (Schweden) finanziert.

Jan 1, 2003

By B Vorster

Falls of Ground is one of the highest causes of incidents, accidents and fatal injuries in our mines today. These falls of ground may occur as soon as the face is exposed after blasting or after machine cutting. The falls of ground can also occur after support has been installed. There are many reasons why these falls occur before and after supporting of the face. It is therefore important to support the exposed face as soon as possible to prevent the falls of ground. It is also very important to support the face with the correct support products and to support the face as designed and required by the mining engineers. The possible reasons for falls of ground, possible support methods and the products available will be discussed in this presentation. In typical conventional narrow vein stoping operations, the use of conventional temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The author wishes to discuss the following items in this paper:- ? Introduction ? Basic face behaviour after exposure ? Controllable Parameters ? Mining Engineers support designs ? Primary and Secondary Support ? Products available for prevention of falls of ground

Jan 1, 2008

By M. L. Baharani

Looking for an idyllic paradise that has investment and business potential as spectacular as the stunning views of mountains, the rich Ganesh Himal zinc-lead deposit exposed between 4,050 m and 5,000 m is the answer. Arising from the sea floor in a span of 55 million years, the enchanting Himalayas had remained one of the most potent factors influencing the Asian region. The challenges of the mighty Himalayas notwithstanding, it continues to provide opportunities for the humankind in optimum usage of the natural resources and sustainable development. Optimal management of natural resources in mountain areas through decision support tools offered by remote sensing will go a long way in realization of the Ganesh Himal Zinc-Lead Project. The authors have a real life endeavor spanning over 37 years in developing a mining industry in a mountainous region of Nepal and an attempt to integrate with the development of other natural attributes of the region. With rapid acceleration of science and technology, humankind has acquired power to transform his environment countless ways and on an unprecedented scale. While mineral resources are the pillars on which we have built industry and infrastructure, industrial countries in the North have been in the forefront of technological advancements, the developed countries of the South have been at the receiving end of exploitation of mineral resources worldwide. A relationship with natural environment, re-crafted by the civilizing impulse, to meet human demands are upcoming challenges for management of natural resource in sustainable manner for a livable world.

Jan 1, 2008

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By R. Strydom, J. H. Selby

Published information is available on the radiological impacts of disposing of zircon sand in a landfill. Zircon flour by virtue of its finer particle size presents a different set of issues during disposal. This paper describes two options for disposal of such fine grained materials – namely incorporation into concrete aggregates and agglomeration by addition of cement. The study considers the radiological exposure of the public from such disposal methods and concludes that these options are viable alternatives for the safe disposal of waste zircon flour. The disposal of zircon into concrete aggregates at a rate of 10 per cent produces a sufficiently low effect to allow such aggregates to be used in building foundations or other such mass concrete applications. The use of cement agglomeration methods will also provide a safe method of landfill disposal provided at least 20 cm of soil cover is included.

Jan 1, 2003

Historically, mine ventilation practices as it was referred to then and which was enforced by legislation of those days, focused primarily on the conditions in the working place and little attention given to actual exposures of workers to contaminants in the working environments. With the advent of the Leon Commission of Inquiry into Safety and Health in the South African Mining industry in 1994, findings in the report indicated that more attention should be given to occupational health of workers. The upshot of this report resulted in the promulgation of the new Mine Health and Safety Act (MHSA) with certain sections of it devoted to all the aspects of occupational medicine and occupational hygiene. This paper describes the present situation with regards to statistics on occupational hygiene performance and compensation paid out to persons who have contracted occupational diseases, as well as the way forward in terms of legislation implemented in September 2002 on the chronic and acute issues affecting the mining industry in SA.

Jan 1, 2003

By P. He

Abstract This paper introduces the test results of dark-gray calcium-shale, discusses the infection of strength characteristic and deformation characteristic due to the angle between structural planes. Keywords calcium-shale, failure form, strength, deformation characteristic, structural planes. Zusammenfassung: basier auf der Anwendung von Problematik des Felsenbauprojektes und Beschaffenheit Felsen unter Beaugnshme auf den Zustand des Druckes von einzeler Welle legt dieser Text dar, wie der Winkel der Schichtstrukturflaeche des schwarzgrau kalziumhaltigen Schieferblocks auf die Zerstoerungs-, Intensitaets- und Deformationseigenschaften einwirkt. Schluesselwoerter: schwarzgrau kalziumhaltigen Schiefer, Zerstoerungseigenschften, Intensitaetseigenschften, Deformationseigenschaften, Flaeche dar Schichtstruktur. Résumé – En fonction de la configuration du massif rocheux sous l’état de la contrainte de pression axiale simple et de la pratique de l’ingénierie de roches, le présent article fait la déscription concernant l’influence de l’inclinaison ? de la couche de structure stratifiée du bloc de schiste calcaire gris noir sur ses caractéristiques de destruction, sa spécificité de résistance ainsi que sa nature de déformation. Mot clés – Schiste calcaire gris noir, Caractéristiques de destruction, Spécificité de résistance, Nature de déformation, Couche de structure stratifiée

Jan 1, 2003

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003

By Kurt R. P Petersen

This paper discusses the current approaches to modelling the DMS cyclone within the De Beers group. Current efforts are split into short term value-adding process understanding and longer term semi-fundamental analysis of separation mechanisms. To date, the basic applied approach has yielded significant value to the group, enabling operators to focus on simple diagnostic measures to control their process. The more involved modelling approach has given rise to a new understanding of the separation field, in particular that the high density gradients within a cyclone are highly localised, indicating that separation of medium to heavy density material takes place low in the cone. The model has proven to be conceptually robust, but still requires further development and validation to become a complete modelling and simulation tool for De Beers.

Jan 1, 2006

By S. Sakurai, N. Shimizu

The stability of slopes is a crucial problem not only in open pit mines, but also in civil engineering situations. The deformational behaviour of slopes is in general monitored during/after the excavation by carrying out field measurements where displacement measurements are commonly adopted. In monitoring the slope stability it should be emphasized that the measurement results must be properly interpreted so as to assess whether the slopes are stable or become unstable in the future. In order to interpret the data, back analysis is extremely useful. In this paper a slope stability monitoring system is described. It consists of displacement measurements by GPS, and a back analysis of measured data. The use of GPS has a great advantage, because of the fact that continuous displacement measurements with high accuracy for a large extent of concerned area can be easily achieved. On the other hand, the back analysis can reveal the mechanical characteristics of the ground, which make it possible to assess the stability of slopes quantitatively.

Jan 1, 2006

By N. A. Barcza

This publication records the proceedings of the Tenth International Ferroalloys Congress, INFACON X, and the third INFACON hosted in South Africa. The Proceedings of the previous two South African congresses in 1974 and 1992 serve, as this volume does, as a valuable record of the papers presented at these important events. This publication comes at a time in South Africa?s democratic development where the theme ?Transformation Through Technology? is very appropriate. The ferroalloy industry has played an increasingly significant role in transformation and black economic empowerment in South Africa, particularly through the advancement and sharing of technology. INFACON X plays an important role in this process, and the stakeholders and organisers of this Congress are thankful for the opportunity to hold this event at this time of transformation in our country. The world of ferroalloys, as well as that of the steel and stainless steel industries, has continued to change rapidly. Recent innovations, better use of resources, increased awareness of environmental issues and ongoing efforts to improve occupational health and safety are among the topics addressed at INFACON X and in these Proceedings. The theme of ?Transformation Through Technology? has been chosen to reflect the regional and global developments in the ferroalloy industry, and the crucial role that technology plays. The Proceedings of INFACON X, the first Congress in Southern Africa of the new millenium, represent a milestone in the technical developments in this major global industry. It contains almost eighty papers in twenty Sessions, from authors in twenty countries, covering raw materials, reductants, energy, electrodes, refractories, furnace design, post taphole services, modelling, simulation, control, sensors, fundamental issues and the applications of ferroalloys as related topics. The major ferroalloys, namely ferrochromium and ferromanganese, are covered extensively in many interesting papers. This comes as no surprise, since South Africa is the leading producer of ferrochromium and also plays a major role in the supply of manganese ore and alloys. Papers on ferronickel, silicon and ferrosilicon ensure that all the large-volume ferroalloys are addressed. These Proceedings of refereed papers of high quality will serve the ferroalloy industry for many years to come, as has been the case with previous INFACON events. For the first time in the history of INFACON, the Proceedings will be available both in bound and in a searchable electronic CD-ROM format. We appreciate the time and effort that the authors and referees have devoted to making this publication a really valuable document. Their contributions are recorded for posterity and reflect the advancements they and their colleagues have made to benefit the ferroalloy industry. Without these ongoing improvements, the industry would stagnate and not fulfil its role in the advancement of mankind. All papers included in these Proceedings were peer-reviewed by at least two referees. About 130 referees were sourced internationally to fulfill this function, and their valuable technical and editing inputs are gratefully acknowledged. Finally, I would like to thank the Technical Programme and Publication committees, led by Dr. Lloyd Nelson and Dr. Noël Machingawuta respectively. Without the tireless efforts of these individuals and their Committee members, the technical programme and these Proceedings would not have been the success they certainly are.

Jan 1, 2004

By S. Okubo, K. Fukui

Empirical equations established for estimating the rock strength of the working face based on the cutting forces of a tunnel boring machines (TBM) are further examined and discussed with respect to the dominant factors affecting TBM performance. Constants in the equations are related to TBM-specific parameters such as excavation (tunnel) diameter, cutter diameter, and cutter distance. The relationship between the constants and the TBM specifications is examined in this study on the basis of data collected at ten tunnels, and it is found that the constants are most strongly influenced by the cutter diameter and tunnel diameter. Zur Schätzung der Gesteinsfestigkeit an der Arbeitsfläche ermittelte empirische Gleichungen, die auf den Schneidekräften von Tunnelbohrmaschinen (TBM) beruhen, wurden weiter im Hinblick auf die vorherrschenden, die Leistung der TBM beeinflussenden Faktoren hin untersucht und diskutiert. In der Gleichung enthaltene Konstanten werden zu den TBM-spezifischen Parametern wie Auschachtungs- (Tunnel) Durchmesser, Schneidendurchmesser und Schachtlänge in Beziehung gesetzt. Die Beziehung zwischen diesen Konstanten und den technischen Daten der TBM wird in dieser Studie auf der Basis der bei 10 Tunnelbauten gesammelten Daten untersucht. Dabei wurde gefunden, dass diese Konstanten am stärksten von den Durchmessern der Schneiden und der Tunnel beeinflusst werden. Cette étude examine et discute les équations empiriques permettant d'estimer la résistance de la roche attaquée aux forces de coupe des tunneliers dans le cadre de l'étude des facteurs dominants affectant les performances des tunneliers. Les constantes de ces équations concernent les paramètres spécifiques des tunneliers comme le diamètre d'excavation (du tunnel), le diamètre du couteau et la distance de coupe. Cette étude examine le rapport entre ces constantes et les caractéristiques techniques des tunneliers d'après des données collectées dans dix tunnels et elle conclut que ces constantes sont principalement influencées par le diamètre du couteau et le diamètre du tunnel.

Jan 1, 2003