Search Documents

By Raymond W. Hiteshue, Sam Friedman, Paul Dobransky, Robert Madden

A hvab coal was carbonized in a closed system at 600 ° C and 40 to 1 , 200 psig to produce a high- Btu gas and char . By retaining the volatiles within the system, it was possible to virtually eliminate production of tars and oils . Depending on pressure and residence time , yields of combustible gases (72 to 92 percent methane ) amounted to 4,000 to 6,000 cubic feet per ton of maf coal and gross heating values of these gases varied from 830 to 960 Btu per cubic foot . Yields of char (maf ) were about 1,600 pounds per ton of maf coal . Increased residence time favored production of gases but reduced their heating values , whereas increase in pressure resulted in somewhat higher heating values and lower production . Similar effects were observed from the carbonization of a low- temperature tar . If these results could be translated to an economical carbonization process for producing high- Btu gas from coal , the demand for coal could be expanded by 40 to 50 million tons per year . Because of large yields of char , a process of this type would obviously have to be integrated with coal - fired power plants . Fortunately , operations could be conducted at essentially atmospheric pressure as product gas under this condition can be obtained in satisfactory yields and with good quality .

Jan 1, 1964

By Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By W. W. Adams, T. D. Lawrence

"The National Safety Competition covering the calendar year 1934 was the tenth yearly safety contest conducted by the United States Bureau of Mines. Participating in the competition were 334 mines and quarries in 38 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies ""Sentinels of Safety.""Since these annual contests were begun 10 years ago by the United States Bureau of Mines the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the prevention of accidents has been achieved, as is indicated by an almost constant downward course in toe accident-frequency rates for the contest group as a whole during the past 10 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the decade and a downward trend during the latter part of the period except in 1930 and 1934; in each of those years a disastrous explosion with abnormally heavy loss of life occurred at the property of one of the participating companies.Because of the abnormal nature of the major disaster in a bituminous-coal mine in 1930 and 1934 the accident-severity rates for the bituminous group for those years are not strictly comparable with the rates for other years. The rates for bituminous mines for 1934 in the present report have therefore been computed on two bases; first, to exclude the record of the company that suffered the disastrous explosion and, second, to include the record of this company. The first rate represents the normal experience of the bituminous coal companies unaffected by the disaster and is therefore more indicative of the real trend of the accident rates for this class of mines from year to year. The latter rate shows the actual experience of all bituminous mines in 1934. The report of the competition of 1930 likewise showed the rates for the bituminous group as computed both with and without the disaster that occurred that year.The National Safety Competition is conducted by the United States Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the facts contained in the accident reports which the competing companies furnish to the Bureau to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest."

Jun 1, 1935

By J. P. Hansen

Reducibility tests were run by the Bureau of Mines on an open hearth lump ore and four groups of pellets whose smelting characteristics had been deter-mined previously in the Bureau's experimental blast furnace. When reduction data from various tests were plotted on specially prepared paper l-(l-percent reduction/100)1/3 against time, the plots were linear. The iron-wustite inter-face therefore advances at a constant rate. The rate of the interface advance in mm/min was used as a reducibility index. The reducibility index measured at 900° C, using 0.45 cu ft hydrogen per minute varied inversely with the surface area of the sample. Even with carefully controlled surface areas, how-ever, duplicate reducibility indices varied considerably. When enough tests were run to give a stable mean, the mean reducibility index did correlate with blast furnace production for the four pellet groups. Results indicated that if the interface speed itself were to be used for correlation with blast furnace production, a sample size of about 180 grams of minus 0.742-plus 0.525-inch particles should be used with a test temperature of 900° C and a flow of 0.45 cu ft hydrogen per minute.

Jan 1, 1966

By A. W. Deurbrouck

The separations achieved by eight conventional cyclone washers have been evaluated to determine their performance when processing intermediate size coal of 28 mesh bottom size. The dense-medium cyclones provided efficient, sharp separations in treating feeds of up to 44 percent of near-gravity material at separating specific gravities ranging from 1.42 to 1,55 (one separation of a secondary feed was made at 1.63). Complete washability analyses are shown by sizes of the composite feed to these cyclones. The magnetite losses per ton of coal processed ranged from 0.6 to 2.0 pounds; however, of the eight plants reporting losses, seven indicated magnetite losses were 1.1 pounds or less per ton of coal processed.

Jan 1, 1972

By T. SPOLAN, G. W. Jones, R. E. Kennedy

Information relative to the explosibility of acetylene at elevated pressures and means of handling acetylene safely under these conditions is of considerable interest at present. American practice limits the pressure at which acetylene may be generated and distributed to poiIits of' use. The pressure in portable acetylene generators is 15 pounds per square inch gage. Tests made by the Bureau of Mines have shown that 15 pounds per square inch gage is too high to prevent explosiofiS of gaseous acetylene in the absence of air; in fact, dry acetylene gai can be exploded at pressures greater than 5.9 pounds per square inch gage. The Bureau has been interested in the explosibility of acetylene for many years because of its continued: use for illumination in many metal mines and its general use in cutting 1illd~--eldifigoperations in the mining maus-try.

Dec 1, 1948

By H. N. Dunning

A comprehensive production research program, now in progress at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville, Okla., includes studies of the displacement of petroleum from sand by detergent solutions. An earlier report (12)2/ presented the results of an extensive research program to determine the value of detergents as floodwater additives. This report presents later results of the detergent-testing program (13, 17). Although water-flooding methods and controls are constantly being improved to increase the production of oil from secondary-recovery operations, considerable crude oil commonly remains.in place after a water flood has been terminated. Therefore, the possibility of improving the efficiency of a waterflood by the use of detergents is of increasing interest. The effects of many substances on the efficiency of water flooding have been investigated in laboratory studies (5, 11, 13, 17, 19, 24). Of the various sub-stances tested, only surface-active agents were consistently effective in removing oil from sand. Results of laboratory studies presented in earlier reports (9, 11, 12, 13) show that many detergent solutions effectively displace petroleum from sand surfaces under varying conditions encountered in centrifuging, manual and mechanical agitation, ultrasonic vibration, and imbibition.

Jan 1, 1957

By William A. Sloan

"In smelting operations, finely divided material called ""flue dust"" is carried by the moving gases from the roasters and furnaces; it is partly settled and recovered in the flue system. The flue dust from copper smelters contains a high percentage of copper, usually some gold and silver, and occasionally other valuable metals. It is too valuable to throw away and in present practice is returned to the smelting furnaces for re-treatment. A part of this material again passes out with the gases and forms a circulating dust load in the system. The dust that passesout of the stacks into the atmosphere is an important source of loss in copper smelting. Loss of values also occurs by dust being blown away while in transit from the flues back to the furnace, and of course the greater the amount of rehandling the greater this loss.Dust carried in the gas currents causes corrosion of the roof arches in reverberatory furnaces. Returning flue dust to the furnace increases the quantity of suspended dust. Corrosion reduces the life of the arches and shortens the length of furnace campaigns; also the corrosion of arches limits the temperature at which a furnace may be operated. Every ton of material that must be re-treated in the furnaces reduces correspondingly the amount of new ore or concentrates that could be smelted.As the present tendency is toward finer grinding in flotation plants smaller particles will need to be treated at the smelters, increasing the difficulty of preventing losses in flue dusts. Many schemes and processes for a more economical method of treating flue dust have been proposed or tried, but in the main none of them has been successful."

May 1, 1928

By E. D. Gardner

This paper is one of a series on milling methods being published by the United States Bureau of Mines. Atlanta is in Elmore County, Idaho, about 80 miles from the railroad at Mountain Home, Idaho. The concentrator is at an elevation of, 6,000 feet and located in a timbered, well-watered region of relatively heavy snowfall. The snow, however, does not seriously affect local operations. The track road to Mountain Home, which passes over a mountain range, is closed each winter from about November 1 to June 15. During this period concentrates are stored and bullion is shipped by airplane. Power is generated by a Diesel engine and by an auxiliary hydroelectric plant. Gold is the principal metal produced; the or also contains an able quantity of silver.

Jan 1, 1935

By J. M. Stuve

Low-temperature heat capacities and the enthalpy of formation were deter-mined calorimetrically by the Bureau of Mines for CuO?CuS04. The derived standard entropy (S°298.15) was 40.36±0.04 cal/deg-mole, and the enthalpy of formation (?H°f) was -219.l±0.3 kcal/g-mole. A large thermal anomaly was observed in the heat capacity of CuO?CuS04 at 20±0.1 K. Gibbs energy of formation data are tabulated up to 1,200 K. Construction details of a precision low-temperature adiabatic calorimeter capable of determining heat capacities of solids in the temperature range 5 to 320 K are given. A calibrated miniature germanium resistance thermometer was incorporated into the calorimeter to extend the range of accurate measurements below 15 K. High-resistance dc heater windings were used throughout the cryostat to reduce heat conduction of inner connecting wires.

Jan 1, 1975

By Frank B. Fulkerson

Mining began in Pend Oreille and Stevens Counties about 1885, Lead and zinc have been the principal products, and the area has supplied nearly all the output of these metals in the State. Fend Oreille County's output of lead and zinc from 1902 to 1956 was 110,700 and 229,600 tons, respectively. The Stevens County total was 54,100 tons of lead and 87,600 tons of zinc. Copper ore was produced mainly from the United Copper mine, Chewelah district, from 1912 to 1920; the principal gold mine was the First Thought, Orient district, which was active from 1904 to 1942. Approximately 225 mines and prospects produced; most of the ventures were on a small scale. The total value of gold, silver, copper, lead, and zinc produced from 1902 to 1956 was $75.2 million in Pend Oreille County and $39.4 million in Stevens County. INTRODUCTION In compiling the figures for this report, use was made of Bureau of Mines permanent records of nine production, the annual tabulations of producing mines, and the Minerals Yearbook. Requests to publish individual data, obtained from the annual production canvass, were made to the latest recorded operators of all mines in the area. Response to this request was good; therefore, it was possible to make the tables nearly complete. In a few instances the producer requested that the production data remain confidential, and in others it was not possible to reach the mine operator at his last known address. The district and county tables combine statistics for all mines, including those mines whose output could not be published separately.

Jan 1, 1958

By E. R. Cole

The Bureau of Mines developed a procedure that enables substitution of zinc cathodes for the aluminum cathodes normally used in commercial zinc electro-winning. Using zinc cathodes eliminates the necessity for stripping and makes it possible to electrowin zinc from solutions derived from material containing excessive amounts of soluble fluorides; for example, zinc concentrates obtained as a byproduct of fluorspar mining in Kentucky and Illinois. To demonstrate the viability of using zinc cathodes, fluoride-containing zinc concentrate was roasted, leached, and purified according to current commercial practice. Electrolysis was carried out in 0.8-, 1-, 5, and 10-liter cells at 35° to 40° C with a cathode-current density of 8 amp/dm2 in a solution containing 65 g/l Zn++ and 200 g/l H2S04 using PbO2 anodes. Zinc deposits were produced on zinc cathodes with good morphology and excellent current efficiency (90 to 94 pct) in solutions containing enough fluoride (~0.5 g/l, F+) to cause sticking of zinc to aluminum cathodes. The approach described has failed previously because of severe solution-level corrosion of the zinc cathodes. The present investigation found that the use of a simple mechanical barrier to prevent oxygen migration from the anode was sufficient to prevent solution-level corrosion of the zinc cathode starting sheet.

Jan 1, 1979

By Carl F. Wingquist

In support of Bureau of Mines studies of thermal fragmentation of rock, the elastic moduli of four types of rock were measured at temperatures ranging from room temperature up to 1,500° F (1,089° K). The sonic method was employed to determine the resonant frequencies of the rock specimens and from these frequencies, the elastic moduli were calculated. Data for Young's modulus, shear modulus, and Poisson's ratio are given as a function of temperature for Dresser basalt, Reserve taconite, Jasper quartzite, and Charcoal granite. Young's modulus and the shear modulus decreased with increasing temperature up to about 1,200° F and then became relatively insensitive to temperatures from 1,200° to 1,500° F.

Jan 1, 1969

By J. L. Eakin

A method was developed by the Bureau of Mines in the laboratory and in the field to relieve capillary waterblocks in gas wells. Impaired gas permeability was improved by this inexpensive chemical treatment which lowers the surface tension of the water held in the capillaries of the formation. Effectiveness of the alcohol-surfactant treatment was tested with a variety of chemicals and with sandstone cores cut from rocks having relatively low permeability. Field tests on 20 gas-producing and storage wells demonstrated the effectiveness and limitations of the method. The productive capacity of some wells was doubled by the treatment. The final test was evaluated by the neutron logging technique for measuring changes in apparent liquid saturation. Maximum apparent liquid saturation was reduced by 52 percent; gas production rate increased from 2.3 to 3.5 MMcfd (million cubic feet per day).

Jan 1, 1965

By R. E. Kennedy

The presence in air of combustible cases and vapors can constitute an extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and has published Its findings. 4/ The explosibility of ethane has been studied, and its limits of flammability have been determined and published. The development of secondary recovery methods of stimulating oil production has intensified interest in the effect of high pressure on the explosibility of natural gas-air mixtures. The limits of flammability of natural gas-air mixtures at pressures ranging from 50 mm. Hg to 350 p.s.i.a. have been determined and published. More recently, the limits have been determined at pressures up to 3,00C p.s.i. in mixtures of natural gas-air-nitrogen.

Jan 1, 1950

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961

By R. L. Hopkins

Fifteen alkyl cycloalkyl sulfides and three dicycloalkyl sulfides were synthesized to provide reference compounds in the search for these classes of sulfur compounds in crude oils. In synthesizing sulfides by alkaline alkylation the order in which the reactants were added was shown to determine the yield and purity of the product.

Jan 1, 1966

By PAUL L. FISHER

This bibliography has been compiled by the Bureau in answer to many requests now being received for information on the briquetting coal and other carbons . In addition to publications issued by the Government in printed or mimeographed form, references are included to articles appearing in the technical press and in cooperative reports of work done jointly with states , colleges , and industries . References and patents are arranged in chronological order . Bureau of Mines bulletins , technical papers and Minerals Yearbooks are printed , and are obtainable from the Superintendent of Documents ,. Government Printing Office , Washington 25 , D. C. Reports of investigations , information circulars , and the directories and reports of the mineral industry surveys are published in mimeographed form and may be obtained without charge from the Publications Distribution Section , Bureau of Mines , 4800 Forbes Street , Pittsburgh 13 , Pa . Many Bureau of Mines publications , as well as bound copies of the foreign and American scientific and trade periodicals , may be consulted in technical , college , and large public libraries throughout the country. Dealers in new and second-hand books sometimes have copies of these reports for sale .

Jul 1, 1948

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a as supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, sortie fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called "bad gas"--return mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory-scale study of direct oxidation of crude oil.

Jan 1, 1934

By M. Clair Smith

This report is one of a series describing exploration, development, mining, and processing of mineral deposits in the United States. The reports are prepared and published by the Bureau of Mines in cooperation with various mining companies The purpose of the reports is to promote development and conservation of our natural reserves by disseminating technological information on mining and milling procedures and related practices at operating mines. Simplot Silica Products, Inc., mines and processes a friable silica sandstone. The finished products are sold for use in glass manufacture, foundries, chemicals, and special applications.

Jan 1, 1959