Search Documents

By P. G. Guest

MANY of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed in operating and anesthetizing areas. When ether was first introduced, candles,5 gaslights, and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions-many of them fatal to patients-have been attributed, with good reason, to sparks from static electricity.

Jan 1, 1953

By Nancy Potts, M. G. Barker, W. C. Holliman

"SUMMARYThis report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, end 10 grade 115/145 aviation fuels.The inspection test data supplied by the participating manufacturers consist of octane and performance numbers, tetraethyllead content, dye color, and other characteristics usually listed in aviation gasoline specifications, such as AN-F-48a or ASTM Designation D910-47T. These data are tabulated and averaged by grades in tables 1 through 4 and, as reported, meet the AN-F-48a and similar specifications with a few exceptions. Two grade 80 gasolines show a lean-mixture octane rating slightly below 80.0, and 91/98 grade fuel shows a lean-mixture rating of 90.9 and a rich-mixture rating of 97.5, two 100/130 grade gasolines have a rich-mixture performance number slightly below 130.0, and one 115/145 grade gasoline shows a rich-mixture performance number of 144.5. However, octane and performance number averages are above the mini¬mum requirements for each grade. Tetraethyllead content in the 91/98 and 100/ 130 grades generally is above the maximum outlined in these specifications, whereas dye color for each of the four grades, with the exception of two gasolines in grades 80 and 100/130, is that designated for the particular grade. Distillation requirements, with a few exceptions at individual points, are met by gasolines of all grades. Reid-vapor-pressure, copper-dish-residue, heat-of-combustion or aniline-gravity-constant, freezing-point, and copper-strip-corrosion requirements are met by all gasolines so far as reported. No data for some of these tests wore submitted on a few of the gasolines. One gasoline, grade 115/145, shows a sulfur content greater than the specified maximum."

May 1, 1948

By Wing G. Agnew

The first six Reports of Investigations in this series , pertaining to the investigation of stemming at the Mount Weather Testing Adit, dealt with ( 1 ) the dust produced by blasting , ( 2) the effect of stemming upon gases generated by blasting , ( 3 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 60 - percent ammonia gelatin dynamite , (4) the length of stemming material through which a primer will fire and detonate a charge of dynamite , ( 5) comparison of dust and gases produced when blasting charges of dynamite in drill holes , bombs, and mud - cap shots , and ( 6 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 40 - percent ammonia gelatin dynamite .

Oct 1, 1943

By W. A. SLOAN, G. L. Oldright, J. D. Sullivan, E. K. PRYOR, A. F. HALLET, R. S. Dean, S. L. BROWN, F. S. Wartman, A. J. Thompson

Lack of sufficient publication funds has resulted in the accumulation of considerable unpublished experimental work on copper metallurgy by the Bureau staff . The present report gives extended abstracts of this work , as well as a discussion of the best direction for future efforts . The experimental work reported in this series of papers was done in cooperation with the University of Arizona , Tucson , Ariz . The investigations covered in the third , fifth , and seventh papers were done under the direction of G. L. Oldright and the remainder under the direction of V. H. Gottschalk .

May 1, 1934

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By M. J. Gavin

Within the past three years numerous inquiries for information on oil shale have been received by the Bureau of Manes. These inquiries have been increasing to such an extent that it has seemed advisable to issue a short paper prior to the publication of a bulletin on the subject, giving a, general discussion of the subject and a comprehensive list of references, so that those interested in the details of obtaining oil from shale can find additional information without much difficulty. Some of those who desire information are interested only in a general discussion of the subject, or are not in a position to refer to books and' articles describing the industry. The material for this paper is largely derived from published information on oil shale. Much of the information is obtained-from the books and articles mentioned in the list of references, and has been compiled with the intent of furnishing information to those not interested in all the details.

Jan 1, 1921

By Robert F. Pettit

This paper on methods and costs of mining and milling iron ore at the Iron Mountain mine of Ozark Ore Co., St, Francois County, Mo., is one of a series of Bureau of Mines reports on methods, practices, and costs of mining and milling throughout the United States. The Iron Mountain operation is notable for its successful transition from open-pit to underground mining, for use underground of large earth-moving equipment, and for development of a multilevel room-and-pillar mining method. Milling methods also have undergone transitions - from hand sorting and log washing in the early days to gravity concentration. Milling ultimately may include flotation to recover additional iron from products now discarded as tailing,

Jan 1, 1957

By Th. G. Sahama

This paper contains some new heat-of-solution measurements of geikielite (MgTiO3), limonite (FeTiO3), fayalite (Fe2SiO4), and a natural forsterite in mixed acid (HF +HCl) and gives the results of a thermodynamic attack on the problem of stability of geikielite in rocks.

Jan 1, 1949

By Richard S. Fowkes

Advanced technology, including automation and computerized information systems, is being adopted in mining at an ever-increasing rate to improve safety and productivity and to decrease overall costs. This U.S. Bureau of Mines report focuses on the human factors issues related to advanced technology. Among the significant facts discovered were the following: Experts studying tile design adoption, and implementation of new technology have stated repeatedly that human factors specialists should be involved from the early planning stages, through design and fabrication, and up to and during production, since human factors has been consistently identified as the biggest obstacle to the efficient utilization of new technology. Also, middle management is generally the greatest obstacle to the adoption of advanced technology, this technology can give rise to worker alienation, boredom, stress, job insecurity, and a sense of isolation; training most of the present work force is more cost effective than hiring new workers; workers are willing to accept new technology if they are given a voice in its implementation; the social and the technical systems should be jointly optimized; and with the intro¬duction of advanced technology, the cognitive or mental, rather than the physical, aspects of human-machine interaction must be emphasized.

Jan 1, 1994

By G. S. Rice, R. V. Wheeler

"In September 1923, a proposal was made through official diplomatic channels by the British Safety in Mines Research Board to the United States Bureau of Mines for ""closer cooperation between the two countries in investigations into the causes and means of prevention of mining dangers."" This proposal was cordially accepted by the Bureau of Mines and was officially approved.In the spring of 1924 cooperation was .formally begun. It contemplated, as stated officially, ""full exchanges of information, a joint program of research, and periodic exchange of personnel so as to assure concordant results. By making the resources of both organizations available it will hasten the attainment of results, will secure better: checks for, accuracy, and in the end will save money for both by avoiding duplication and repetition.""This joint work has been carried-on successfully since that time and has developed valuable results, reports on which have been issued from time to time. The progress report which follows gives the results of the studies and work carried on in 1929.During 1929 all the phases of our cooperative research, begun in previous years, have developed normally. The exchange of formal monthly reports on all programs of mutual interest has been continued and has proved an invaluable, means of maintaining contact between the investigators of both organizations. There has been no diminution in the exchange of routine progress reports on specific subjects or in direct correspondence. The interchange of personnel has been maintained, and we can say that the mutual benefits to be derived from this form of cooperation are so great as to be difficult to overestimate. It leads to an appreciation of methods of research and modes of thought in the interpretation of results obtainable in no other way, and engenders a frankness and intimacy which must continuously enhance the value of future cooperation.Dr. S. R. Katz, who was assigned for service with the Safety in Mines Research Board in April, 1928, returned to America in May, 1929. During his stay in England he completed, in cooperation with members of the board's staff, the equipment of a gas-mask laboratory and designed and tested a new form of gas-mask canister. A publication of the Safety in Mines Research Board dealing with this investigation has been prepared and approved and will .be .issued in the near future. In additions Dr. Katz imparted to those with whom he was associated much of his knowledge and technique regarding his particular subjects. He delivered two lectures to the board's staff, the subjects be ""Gas Masks"" and ""The Intensity of Odors"", and gave papers before the Midland Institute of 'lining Engineers and the Birmingham University Mining Society on the subject of ""Industrial Gas Masks""."

Jun 1, 1930

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

By G. V. Sullivan

The Bureau of Mines conducted preliminary beneficiation studies of a gold-bearing graphitic schist from Blue Hill, Tallapoosa County, Ala. The average analysis of the material was 0.08 oz/ton gold. Tabling of minus 35-mesh material recovered 83 to 94 percent of the gold at grades of 6.925 to 2.165 oz/ton, respectively. A combination of jigging and tabling resulted in a concentrate assaying 24.3 oz/ton gold and contained 87 percent of the total gold. Treatment of the material by jigging, tabling, and amalgamation recovered 86.5 percent of the gold.

Jan 1, 1969

By W. C. Phalen

"Tho the term “magnesite” is generally applied to the iron-bearing carbonate of magnesium, such as is found in Austria and Hungary, by some Austrian magnesite is referred to as bruennerite. The mineral bruennerite has become of commercial importance only in Austria. The important deposits are found in Styria, lower Austria and northern Hungary. It is of interest to know that the world's largest deposit of spathic iron ores or iron carbonate (FeCO3), occurs at Eisenerz, Styria, while the world's largest deposit of spathic bruennerite is found at Veitsch in the same province.The Styrian and lower Austrian deposits are located much nearer the Adriatic sea than are the deposits of northern Hungary; and it is from the former that most of the exported magnesite has come. They are located south-west of Vienna, and extend west from Semmering thru the Murz Valley to Tyrol. The chief deposits reckoning from east to west are those of Semmering, Veitsch, Breitenau, Trieben, Radenthein, and Dienten.The largest and most important deposit is that at Veitsch located near Mitterdorf, on the South Austrian railroad in the Murz Valley, Styria. Here the magnesite, which occurs in the form of a lens is quarried on the slope of a hill in a series of terraces about 50 feet apart. The entire work extends thru a vertical distance of 500 feet. The huge magnesite lens is nearly 4 of a mile long and over 1,000 feet in width, and probably extends to a considerable depth.The formation containing the magnesite extends eastward beyond Vienna into Northern Hungary where magnesite is quarried beyond Jolsva and Nyustya in the Gomor district. In spite of the remote location of these deposits as compared with those in Styria, magnesite was shipped from them before the war a distance of 360 miles to the port of Fiume for overseas shipments to other parts of Europe and to America.The average analysis showing the composition of the Austria-Hungary mineral is as follows:The magnesite occurs as lenticular masses in a belt of Carboniferous rocks consisting mainly of metamorphosed Shales, sandstones, conglomerates,,and limestone, It is grayish in color when fresh, and contains sufficient ferrous carbonate to blacken it when calcined. It turns brown owing to the oxide ion of the ferrous carbonate when exposed to the air. The quantity of carbonate of iron is ariable and different analyses show that it ranges up to 13 or 14%For the most part, only the sintered article has been imported into The United States. This material has achieved an enviable reputation for its uniformity both as to chemical and physical characteristics. The homogeneity of the sintered Austrian magnesite is doubtless due in part to the averaging effect of the different operations, such as crushing, dressing, sintering, And mixing, n effect which is not obtainable in mere hand samples.There is comparatively little variability in the sintered magnesite as marketed, and five analyses of this sintered magnesite as quoted by Cornu* are gas follows:"

Aug 1, 1919

By W. D. Walker

All pipelines used to transport liquid fuels over coal mines are potentially hazardous; however, this publication deals only with dangers in transporting gasoline. Since transporting gasoline by this method is an established practice, the hazards connected therewith should he recognized by coal-mine operators and pipeline companies so that every known precaution may be used to reduce and keep the hazards to a minimum. The purpose of this paper is to direct the attention of coal-mine operators and employees, pipeline-company officials, and other interested persons to the explosion and fire hazards that arise from seepage of gasoline into underground mines. A hazard is not only presented in an individual mine when gasoline enters underground workings; but, in cases where mines are interconnected, a hazard exists in mach such mine.

Jan 1, 1954

By James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is fieldworthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

By H. M. Smith

[ ]

Jan 1, 1927

By Arthur Crowfoot

This paper describing t o concentrating practice of the Phelps Dodge Corporation, Morenci Branch, at Morenci, Ariz., is one of a series of articles on concentrating methods and posts being prepared by the Bureau of Mines. The Morenci concentrator, locally known as No. 6 concentrator, treats 5,000 dry tons of ore per 24-hour day by primary tabling followed by two stages of flotation treatment, at 48-mesh size and 65-mush size respectively.

Jan 1, 1931

By B. H. Eccleston

The effect upon automobile emissions in changing from leaded to lead-free gasolines was studied in experiments by the Bureau of Mines in cooperation with the American Petroleum Institute. Typical U.S. leaded gasolines and prototype lead-free gasolines of comparable octane quality were used in eight vehicles operated to simulate city driving. The experiments were run at 70° and 95° F. Exhaust and evaporative emissions were measured and the photochemical effect of the emissions was experimentally observed in an artificial smog chamber. Results of the study reveal the manner and degree in which the changes in fuel composition alter the amount and characteristics of both exhaust and evaporative emissions. Briefly, it is shown that the compositional differences between leaded and prototype lead-free fuels resulted in higher photo-chemical pollution potential of the emissions from the lead-free fuels. The effect is attributed to the photochemical characteristics of high-octane fuel components that are used in greater quantity in the lead-free fuels.

Jan 1, 1970

By Lindsly. Ben E.

"The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2Lewis3 states, ""The estimate of 80 to 90 per cent of the oil left underground does not seem incredible.""It is estimated by the writer that approximately 91 per cent of the oil originally held in the Elliott pool, was still in the formation on January 1, 1924, and that it would take at least 12 years, at the 1923 rate of production, to further reduce this quantity by one per cent of the original content.The progress made in the oil industry during the past few years relative to the prevention of evaporation losses; to improvement in cracking processes, whereby the gasoline yield from many crudes has been doubled and trebled; to the increased recovery of gasoline from natural gas; and many other developments, remarkable as they are, can be applied only to that comparatively small portion of petroleum products which are raised to the surface. A device or process which would cut development costs to one-half would probably result in a much smaller profit to the oil industry, than the profit derived from an additional 10 per cent recovery of the total amount of oil in a pool. Various methods have been used and many others proposed, for the increase of oil recovery from normally depleted sands.In France, oil sands are being mined by means of shafts and galleries. In other places, notably the Bradford, Pennsylvania field, the yield has been increased by means of water flooding, wherein water is introduced into the sand to displace oil, and drive it to producing wells."

Oct 1, 1926

By J. M. Riley

The Bureau of Mines investigated a promising new technology for recovering A1203 from alunite to support the Bureau's alumina miniplant project. Results are presented for a study of the technical feasibility of treating alunite crushing and grinding reject fines for recovery of A1203. Alunite pellets having sufficient strength and resistance to degradation were produced by combining fines and coarse alunite with a KOH binder. The best pellets were prepared, in a laboratory pelletizer, by adding 1 pct KOH as a 5-pct solution to a mixture of 40 pct alunite dust (98 pct minus 65 mesh) and 60 pct coarse alunite (minus 20 plus 65 mesh). Calcines suitable for K2SO4 and A1203 recovery were produced by reducing dehydrated alunite pellets with sulfur in a laboratory shaft furnace for 4 h at 600° C, followed by air oxidation of the reduced calcine for 1 h at 600° C. This report presents design calculations, schematic diagrams, and discussions of the essential features of a proposed process research unit (PRU)--a continuous, 6-lb/h alunite shaft furnace--for studying the process.

Jan 1, 1983