Search Documents

By J. A. Lamonica

The Bureau of Mines conducted an environmental noise survey to determine the noise levels to which underground coal mine employees are exposed, to evaluate noise survey techniques and equipment, and to compare noise exposures using two criteria, Walsh-Healey and CHABA, for determining allowable exposures that were under consideration for the Federal Coal Mine Health and Safety Act of 1969- Time study techniques and Bureau-approved standard sound level meters were employed. The shift exposures of 20 percent of the miners studied were in excess of the safe standards established by both criteria. The shift exposures calculated using the Walsh-Healey criteria were greater than those calculated using the CHABA criteria owing to the intermittent nature of the exposure. Ultimately the CHABA criteria were rejected, and the Walsh-Healey criteria were adopted.

Jan 1, 1971

By Linneas Laage, Thomas Weber, William Pomroy

"Underground mine fires can significantly influence mine ventilation airstreams, in some cases throttling or even reversing airflows. As a result, the performance of a metal and nonmetal mine stench fire warning system, which depends on the ventilation to carry the vital warning signal, under fire conditions is different from performance under nonfire conditions. The safety of underground miners can be jeopardized if the warning signal is delayed. This Bureau of Mines report describes research to investigate fire and stench warning system interactions. A computer model is presented that permits quantitative analysis of stench warning signal delays as a function of fire location and intensity. The results of a case study involving computer simulations of stench distribution in a hypothetical mine network subject to various fire exposures are also discussed. This case study illustrates a technique for identifying the areas within a mine that are subject to unacceptable warning signal delays, thereby enabling preemptive action by mine personnel, such as redeployment of stench injectors. INTRODUCTIONFires are an ever-present threat to the safety of underground miners. Since the smoke and toxic gas produced by a mine fire can be spread rapidly by the mine's ventilation system, mine evacuation must be accomplished as quickly as possible in the event of fire. In metal and nonmetal mines, the most common means of passing the fire warning signal to each miner is the stench system. The typical stench system utilizes ethyl mercaptan, a highly odoriferous organic compound, injected on the surface into the compressed and/or ventilation airstreams. Upon smelling the stench, workers evacuate the mine according to an emergency preplan.Although the stench system has been used successfully for over 60 yr, it has several serious shortcomings, owing to certain chemical properties of ethyl mercaptan and to certain performance characteristics and limitations of present injection systems.Recent Bureau research succeeded in upgrading the overall safety and effectiveness of the stench system through the use of a superior stench odorant and the development of improved stench injection equipment (1).4 This research has also investigated a specialized computer simulation model capable of calculating the precise concentration of stench in any mine ventilation network branch at any time after stench release (2). An adaptation of the computer model now enables the analysis of stench system and ventilation system interactions under the influence of a mine fire."

Jan 1, 1987

By Lloyd Williams

1. This investigation shows that the Sewanee bed is the only coal bed being mined in Sequatchie County. Other coal beds are present, but as they do not contain known recoverable reserves, estimates of reserves were made only for the Sewanee bed. 2. Known measured and indicated reserves in the Sewanee bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 76 million short tons as of January 1, 1953. Of this total 62 million short tons represent coal 28 inches and more thick. Areas in the bed were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1955

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

The Tenth International Conference of Directors of Safety in Mines Research was held in the United States from September 28 through October 2, 1959, at Hotel Webster Hall, Pittsburgh, Pa. The Conference was organized by the Federal Bureau of Mines. In accord with the program outlined at the Ninth Conference (1956, Heerlen, Holland), the papers submitted dealt with the following three subjects: 1. Safety of coal mine explosives 2. Explosion hazards in mines 3. Ignition and fires in mines Seventy papers were presented. There were eight technical sessions followed by an extended tour of the Bruceton facility of the Bureau of Mines on October 2. Simultaneous translation was provided in the three official languages of the Conference--English, French, and German.

Jan 1, 1962

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By Samuel P. Harteis

Many mining operations rely on retention bulkheads to provide a barrier between impounded water and active mine workings. However, bulkhead failures can cause catastrophic flooding that puts the underground workforce at risk. Underground observations and evaluations of existing bulkheads indicate that a systems approach is required when building an underground water or slurry retention system. In addition to engineering the bulkhead, the designer must ensure the quality control of materials and workmanship of the bulkhead, the reaction of the mine strata when exposed to water under pressure, and methods to monitor the performance of the retention system. Researchers from the National Institute for Occupational Safety and Health (NIOSH), with the assistance of the Mine Safety and Health Administration (MSHA), conducted an extensive review of bulkhead permits submitted to the MSHA Technical Support office in Bruceton, PA. In addition, the researchers visited accessible bulkhead installations at undeground mining operations to gather information related to construction practices, maintenance issues, and monitoring and emergency response procedures. Several key items were identified that must be considered when permitting the installation of an underground fluid retention system.

Jan 1, 2008

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By Robert L. Virta

This U.S. Bureau of Mines paper discusses the structure of the talc industry, talc production, processing of talc ore, applications and demand for talc, and the outlook for the talc industry.

Jan 1, 1989

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By Harold M. Smith

Natural gas has been used as a fuel and source of energy almost from its discovery, but its use as a chemical raw material may be said to have begun in 1918, when Brooks and Humphrey3/ showed. presence of alcohols in the diluted acid oil obtained by the sulfuric acid-treatment of cracked petroleum distillates. However, development of the utilization of natural gas for chemical syntheses was slow, partly because erroneous ideas existed regarding the nonreactivity of tine hydrocarbons composing natural gas. Data accumulated by petroleum chemists throughout the world, particularly since about 1930, have shown that these hydrocarbons will react when activated by the effects of heat, pressure, chemical reagents, and light; also that the reactions can be made to proceed of practicable speeds and to provide good yields of useful products with moderate operating conditions, especially if catalysts are employed. As those results became known, the possibility of a synthetic organic chemical industry based upon these reactions became apparent, and today this industry is large and growing rapidly in importance. In this paper the story of the manufacture of chemical products from natural gas is told simply in graphic form. The industry is developing so rapidly that soma products may have been omitted, but every effort has been made to include all that are important or likely to become so. The difficulty of keeping information of this tape up to date is shown by reference to an information circular4/ or, the sore subject published by the Bureau of Mines in 1930, in which the important products are shown on a single chart, where as five charts are employed for the cane purpose at present.

Jan 1, 1940

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By Todd M. Ruff

This report summarizes ongoing research at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, in which collision warning systems for surface mining dump trucks are being evaluated. Common accidents involve these large trucks running over smaller vehicles or pedestrian workers. Collision warning systems currently use one of several methods, including radar, radio-frequency-signal detection, or ultrasonic signals, to detect and warn of the presence of an object or person in the blind spots of the mining equipment. Most available systems have not been tested on large off-highway dump trucks. This report evaluates several systems on two sizes of trucks, a 50-ton-capacity truck commonly used in quarries and construction and a 240-ton-capacity truck commonly used in open-pit mines. Tests were conducted to determine false alarm rates, alarm effectiveness, and reliable detection zones for a person and a pickup truck. The results indicate that radar and radio-frequency identification systems show promise for this application and that several of the improved systems are ready for extensive field tests. However, challenges still exist in applying these technologies to large trucks.

Jan 11, 2000

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. There are several portions of the handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-1) List of Most Frequently Encountered Contaminants (Page 2-2) List of Candidate Contaminants and their Sampling Conditions (Table 2, Starting on page 2-5) Interpretation of Results (Page 2-16) Procedure for a, Health and Safety Inspection (Page 2-25) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, the Glossary of Terms, and the List of Commercial Products Encountered in Surveys.

Jan 1, 1975

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

The following is a Maintainability Design Checklist for coal mining equipment. The purpose of the checklist is to provide a summary of design review points for the maintainability assessment of new or existing underground equipment. It specifically focuses on the identification of equipment design features, tasks, or procedures that impact equipment downtime, repair costs, labor hours and maintainer skill level requirements. Some checklist points are general in nature. The checklist was designed to be used across all categories of underground equipment. The intent is to draw attention to design features and maintenance procedures that will increase maintainability requirements. You are encouraged to adapt this checklist to site specific or machine specific requirements by: ? Inserting specific performance criteria for various categories of maintenance tasks. For example; all hydraulic lines on a shuttle car should be replaceable in 15 minutes or 25 minutes, etc. ? Adding or deleting checklist items for different categories of equipment. You would include environmental control equipment, for example, on face equipment and not on shuttle cars or man trips. ? Adding additional checklist items based on site or equipment specific maintenance histories or experience, company maintenance standards, or other factors.

Jan 1, 2000

By Gregory R. Wagner

The Program of Mine Safety and Health Research described in this document reflects the continuing commitment of the Spokane and Pittsburgh Research Laboratories to focus on the most important areas where research can make a difference in reducing risk and improving safety and health for miners. It is the first program of work conducted since Congress mandated closure of the former U. S. Bureau of Mines (USBM) in the Department of the Interior and supported integration of the health and safety research function of the former USBM into the National Institute for Occupational Safety and Health (NIOSH). Organizational changes made FY97 a challenging year of transition. Ongoing research was reviewed and revised to reflect the new, more limited, health and safety mandate of the research laboratories. The mining industry, mine worker representatives, and interested government agencies provided broad input to assure that the research performed would focus on the most critical safety and health problems confronting mining today and which are expected to be faced in the future. The two laboratories worked to evolve coordinated programs of safety and health research, each with a special focus. The work of the Spokane Research Laboratory is directed toward issues of special importance to the Western mining industry, particularly those safety hazards found in metal/nonmetal mining and surface mining. The work of the Pittsburgh Research Laboratory will continue to focus on Eastern mining, particularly underground coal mining. Traditional areas of expertise for understanding and preventing fires and explosions and for controlling the hazards of dust and noise will continue to reside in Pittsburgh. Each laboratory is developing new capabilities in the analysis of relevant safety and health information to assure that program priority-setting decisions are informed by the best available data. Recognizing the continuing importance of communicating the results of research to all who are capable of improving safety and health conditions in mining, each laboratory has developed an activity for information dissemination and coordination with stakeholders. In the midst of organizational self-examination and change, the research staff in Pittsburgh and Spokane have never wavered from their continuing commitment to conduct the highest quality scientific research-solution-oriented scientific work meant to reduce the risk of injury, disease, and death from occupational hazards in mining. The pages that follow give insight into some of the program activities and accomplishments from FY97. I hope you share my pride in the many accomplishments of the NIOSH mine safety and health research program during this year. This report comes at a time of increasing stability for the mine health and safety research program. The organizational changes in Spokane and Pittsburgh have been concluded, and NIOSH has succeeded in recruiting a new, permanent associate director for mining to lead this critically important national program. Congress has contributed to an optimistic future by providing expanded funding for NIOSH mining-related research for the next fiscal year. On a personal note, I greatly appreciate the opportunity I have had to serve as the NIOSH Acting Associate Director for Mining during this transitional year. The commitment and intelligence with which the mining research staff pursued their mission was matched by their patience and understanding in moving into a new organizational environment. All of us committed to improved safety and health for this Nation's miners owe them our respect and appreciation.

By Fun-Den Wang

Rock bolting has become a major method of coal mine roof support because of its effectiveness, economy, and convenience. The polymeric-resin-bonded bolt has generally proved to be more effective than the mechanically anchored bolt, but the higher cost of the resin bolt limits it to applications where the increased support is essential. The low-cost high-early-strength cement grout developed during this project will encourage more widespread use of fully grouted roof bolts provided practical installation techniques can be developed. Laboratory tests of four types were performed on various rapid-set and accelerated cement products to find a material with properties suitable for replacing resins. A proprietary gypsum cement was ultimately used with good success. A field test of the cement grout was made in an operating coal mine. An intersection was bolted in the standard pattern with cement-grouted bolts and instrumented. A nearby resin-grouted intersection was also instrumented and observations were carried out in both intersections for 2 months. No substantial difference was found between the support provided by the cement and the resin.

Jan 1, 1976

This article updates the status of fatalities occurring in both coal and metal/nonmetal mines from January through December of 2001. Based on preliminary accident reports, as of December 31, 2001, seventy-two fatalities have occurred at coal and metal/ nonmetal mining operations. During this period, forty-two fatalities occurred at coal operations and thirty fatalities occurred at metal/nonmetal operations. Ignition or explosion of gas or dust and fall of roof were the most frequent accident classifications in coal and powered haulage fatalities were the most frequent accident classification in metal/nonmetal.

Jan 1, 2002