Search Documents

By R. J. Matetic, David S. Yantek, David K. Ingram

The National Institute for Occupational Safety and Health (NIOSH) has investigated engineering noise controls to reduce sound levels in cabs on air-rotary drill rigs. A recent investigation revealed that some drillers are exposed to A-weighted sound levels exceeding 85 dB even though a cab is used. NIOSH studied the in-cab sound levels of one such rig. First, preliminary tests were conducted in a controlled environment using accelerometers and microphones with spectral analysis to identify the dominant noise sources for in-cab sound levels. The results indicate that vibration transmitted from multiple hydraulic pumps to the control panel produces a dominant spike in the sound level spectrum in the 400 Hz 1/3-octave band. Next, field tests were performed in a production environment to evaluate noise controls to reduce in-cab sound levels. It was found that utilizing hydraulic noise suppressors reduces the structure-borne noise transmitted to the control panel. Further, using hydraulic noise suppressors and enhancing soundproofing reduced the in-cab A-weighted sound levels by as much as 4 dB.

By D. A. Paice

Under the first phase of this contract as reported in the Phase I report it was determined that certain types of commercially available molded case breakers are capable of interrupting mine dc power supplies of nominally 300 volts or 600 volts rating. These circuit breakers incorporate conventional overcurrent trip units but also can be operated by means of low power signals fed to a shunt trip coil. Further development in the Phase I program produced a means whereby a discriminating circuit breaker detector unit could sense the presence of illegitimate loads on the dc electrical system and cause the circuit breaker to trip. The detector unit operated by detecting the presence of 3000 Hz currents which were generated in the illegitimate loads by means of a 12 volt, 3000 Hz signal applied to the dc system. Further development of the program has continued in Phase II with the aim of verifying the practicability of the complete discriminating circuit breaker concept and developing other types of equipments required to implement a system. These other equipments include electronic means for raising the apparent impedance of high power legitimate loads and static filters for smaller loads. The results of laboratory work and limited underground tests have been successful. This report describes the system and the tests that have been conducted on the various equipments that comprise the complete Discriminating Circuit Breaker Concept.

Jan 1, 2012

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By Lloyd A. Morley

Proposed advantages and disadvantages of low-voltage shielded trailing cables are formulated utilizing the literature and industry sources. A partial analysis of these proposed advantages and disadvantages is completed through a review of the literature. Cable costs are assembled from mine operators, cable and splice manufacturers, and actual cable purchases. To confirm each advantage and disadvantage, an underground test site is established, and testing is performed here and in the laboratory. All testing procedures are completely described. The results of this investigation are reported and used to formulate recommendations attendant to low-voltage shielded cables. Suggestions for installation, handling, and maintenance are presented.

Jan 1, 1977

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By T. A. Klinefelter

KYANITE and the related minerals sillimanite, andalusite, dumortierite, and topaz are natural aluminum silicates that can be used in production of mullite (3A1203?2Si02), a superduty refractory material. Kyanite and sillimanite are the dominant ones because of their greater abundance. The only other kyanite-group mineral presently used for mullite production is andalusite. Mullite is not an absolutely essential material as other refractories can be used in the same heat range. However, it is a highly satisfactory one. It is the only compound of silica and alumina that is stable at high temperatures. It has low thermal expansion and is very resistant to corrosive melts and to thermal shock. For these reasons mullite refractories have a much longer life than standard fire-clay refractories under the same conditions. Worldwide, excluding U.S.S.R., the refractories industry consumes about 150-000 short tons annually of kyanite group minerals and synthetic mullite.

Jan 1, 1961

By W. M. Myers

[Utilization of small stone is recognized as one of the important problems of the lime industry. The term ?small stone' is used to designate material that is too small for calcination in tie shaft kilo. The maximum dimension A such stone rosy be placed at four inches. The introduction of any considerable quantity of stone having demensions lee: than this into the charge of a kiln impedes the draft and readers successful operation of the kiln difficult on impossible. Attempts design a shaft kiln which would calcine stall stone satisfactorily have not been successful to date. Thousands of tons of this small stone arc produced daily, and while part of it finds a market, for it has many uses, the profit is usually small an competition is teen and prices are low. Production of the material is, however, so greatly in excess of market that surplus of hundreds or possibly thousands of Jose axe place daily in stock piles and classified as waste. in a few instances a fortunate combination of circumstances, such as a program of or other work requiring large quantities of concrete aggregate, may mate it possible some quarries to market this stone later at a profit, teat in general the chances A profitable utilization are slight, and the quarry operator has the expense of handling this waste stone and providing a storage site for it. The brittle nature of limestone makes it impossible to quarry the stone and crush, it to size suitable for the shaft kilns without producing an excess of undesirable fines. Elimination of fines by changes in quarrying or crushing practices cannot lee expected. On the contrary, the adoption of more modern methods of quarrying in recent years has increased the proportion of small material. The tendency is to blast the roan with large charges of explosives and crush it with mechanical crushers, which produces more fines than the older methods of careful blasting with small char yes and sledging the rock by hand.. We increasing use of underground mining of limestone has also increased the production of small stone, as blasting in the confined space of an underground stope shatters the rocs more completely than quarrying in the open. The use of the very friable limestones, such as the limestone of Florida for the manufacture of lime adds a new factor to the calcination of small stone. These friable lime limestones have a low tensile strength and crumble in the kiln, causing trouble. Successful calcination of these stones is accomplished in specially]

Jan 1, 1926

This report describes the activities and publications of the Bureau of Mines Health and Safety Research and Testing Center, Pittsburgh, Pa., for the fiscal years 1960-65. It includes a discussion or work being conducted on roof control, dust explosions, ventilation, health, coal mine fire control, and electrical-mechanical testing, and an abstract of each paper published during the report period.

Jan 1, 1966

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

By Denis Dwyer

[This paper describing mining, treatment methods, and costs at Plant No. 1 of the Western Indiana, Gravel Co. at Lafayette, Ind., is one of a series on gravel and sand mining being prepared for and published by the U. S. Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to industry as a whole. On the other hand, operating costs are essential to e technical discussion and study of the methods employed, The attention of the reader is specifically called to this differentiation in order that no Misunderstanding of the scope of the cost tabulations shall ensue.]

Jan 1, 1933

By W. A. Calhoun

"INTRODUCTION A letter from S. D. Strauss, vice president of Metals Reserve Company, Washington, D.C., dated May 22, 1945, to the chief of the Metallurgical Branch, Bureau of Mines, in Washington; includes the following: Because of the present critical shortage that exists in the supply of corundum required by certain industries in war production, the Reconstruction Finance Corporation, Mr. W. C. Keeley, Vice Chairman for Metals and Minerals, War Production Board, has recommended that the Reconstruction Finance Corporation though Metals Reserve Company, proceed with preliminary mill testing of the corundum ore in Gallatin County, Montana, and that the results of that testing be transmitted to the War Production Board. If the results of the testing work are considered satisfactory, Metals Reserve Company will then provide for the actual mining and milling of the ore for the production of corundum concentrates.Pursuant to the above stated recommendation by the War Production Board, Metals Reserve Company desires to make -use of the facilities of the Bureau of Mines testing plant at Rolla, Missouri, for conducting sink and float and other concentration tests on representative samples of the Montana corundum ore. Two, and possibly three samples of ore are to be tested which will have an aggregate weight of approximately 50 tons."

Dec 1, 1947

By Donald E. Ralston

The Huntsville study area in northeastern Alabama consists of Jackson, Limestone, Madison, and Marshall Counties. Major emphasis was placed on the Huntsville urban area in Madison County to analyze the relationship of urban growth and the minerals industry. Huntsville was delineated into its component urban, suburban, and rural parts for 1964, and the primary area of growth was predicted for 1990. Population estimates were made for the four-county area as a unit and Madison County separately, and projected to 1990. Demand estimates for crushed stone and sand and gravel were made for the same area units and projected to 1990. Analysis of quarry sites in the Huntsville area was made for the present and for the future. The mineral operations of the study area are all located in rural areas; in the case of Huntsville, the mineral sites are located in areas defined as "rural" in the component urban-suburban-rural system. The operations outside Madison County can expect to have minor problems with urban encroachment, while those operations in Madison County can expect major problems associated with urban growth and development. Some of the problems associated with limes tone production can be reduced if producers invest in capital equipment that will reduce the nuisances inherent in this activity. Although urban expansion endangers some quarry operations in Huntsville, topographic and political restrictions which prevent urban expansion can effectively shield quarry operations for some time.

Jan 1, 1970

By H. S. Auvil, L. D. Schmidt, H. G. Graham

"Several studies on the bulk density of coals prepared for byproduct-oven use were undertaken during the war by the Bureau of lanes in cooperation with the Office of the Solid Fuels Administrator and with the advice of the Coke Production Committee. The primary purpose of these studies was either to produce more uniform coke or to increase the throughput of existing facilities or both; the goal was increased Production of steel for war. As these studies were made, detailed reports were sent to the individual companies with whom the Bureau cooperated; also two reports,5/6/on the general subject of bulk-density control were published. In the course of the work, data were gathered that now prove of value in judging the merit of carious methods of testing bulk density and the limits of application of each method in byproduct-oven operations.Since the cessation of hostilities, the .Bureau section (Coke Production Survey Section) that conducted this work has been liquidated, but it was felt advisable to prepare a report on the accumulated experience so that it would be in a form available for the use of the industry and also as a base for any further research on the control of fluctuating bulk densities in coke ovens.It is hoped that the data and experiences recorded herein will be of material assistance to the many who have had difficulty in obtaining reproducible results in bulk-density testing. Since the data were gathered in the course of extending aid to individual plants in minimizing the deleterious effects of fluctuations in bulk density of oven charges on the quality and quantity of coke produced, certain desirable phases of an over-all investigation were not covered. However, on certain of these phases qualitative indications are available and the policy followed herein is that suggested by the American Society for Testing Materials Manual on Presentation of Data7/ that lacking quantitative information, relevant material should be included even though it ""may be qualitative in character, some may even be vague."""

May 1, 1946

By G. B. Shea, R. A. Cattell

This resume of the work of the Petroleum and Natural - Gas Division of the Bureau of Mines for the fiscal years 1940 and 1941 is the second of a series. of progress reports . It brings forward from the 1939 annual report information on the course of activities of the division in carrying out its objectives of increased conservation and better utilization of petroleum, natural gas, and related resources through a coordinated program of research and fact - finding . It discusses, also, special assignments. executed for other Government agencies, which in recent years have constituted a considerable part of the division's work ." . In the present national emergency, in which petroleum is so essential , many of the Bureau's research activities bear directly on the availability, conservation, and use of petroleum for national defense . Accordingly, during the past year attention has been focused for the most part.on.problems associated with the needs of national defense . Several long-time researches , which in themselves are potential sources of desirable knowledge , were judged to be of secondary importance under present conditions and accordingly were suspended . Studies also were oriented in line with rapidly changing conditions to meet the demand for accurate findings on short notice . The Petroleum and Natural - Gas Division has experiment stations at Bartlesville , Okla . , and Laramie, Wyo . , a field office at Dallas , Tex . , and a field office and laboratory at San Francisco , Calif . It also operates the Government helium plant near Amarillo , Tex. In addition to the helium operations , some of the petroleum and natural - gas research activities are conducted at the Amarillo plant .

Feb 1, 1942

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

By R. L. Schmidt

One of a series published by the Bureau of Mines covering research investigations in rock drillability, this report of field drilling results extends earlier laboratory findings and provides a relatively simple procedure for predicting percussive drilling rates with reasonable accuracy. Two percussive drills mounted on a truck were used to drill a total of 25 rock types, and the results were used to develop a prediction equation. The equation was tested on a set of unrelated laboratory percussive drilling data, and the comparison between predicted and actual rates is shown in tabular form.

Jan 1, 1972

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963