Search Documents

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By Ingemar Hermansson, Thomas Bjerendal, Mattias Grävare, Carl-John Grävare

"AbstractHigh strain dynamic pile tests (HSDPT) on driven piles have been carried out on a routine basis in Sweden for more than 30 years. The Swedish Commission on Pile research established, in the early 1980s, safety factors based on the percentage of piles tested. The safety factors could then be reduced, creating economic incentives for the contractor to carry out testing.Energy formulas adopted by our neighbour countries, Norway and Denmark, were not accepted in Sweden as a reliable method since the dynamic testing method was considered to be a more scientific and reliable method. It has become almost the only in-situ method used to verify geotechnical bearing capacity on driven piles.The typical Swedish geology of soft soils overlaying very hard strata makes it possible to verify high design loads, typically 20 kN per cm2 of pile cross sectional area for steel piles and 1,5 kN per cm2 for concrete piles.Conventionally a certain percentage of the piles have been tested in Sweden. The EC7, on the other hand states a number of piles to be tested, regardless of the total number of piles. The Swedish NA (National Annex) states a maximum distance between tested piles, which results in better distribution of the test piles over the foundation.For shaft-bearing piles in soft clays, dynamic pile tests have to be correlated by static load tests.Historical backgroundOn a research basis stress-wave measurements have been carried out for a long time in Sweden. One example is a project in the city of Gothenburg, conducted by Fellenius and Pejrud (1964). Strain gauges were glued on the reinforcement bars in 60 m long, precast concrete piles at 3 m and 25 m above the pile tip respectively. Evaluation was done with different methods such as dynamic formulas,stress-wave measurements and in addition compared with static load tests.In the 1975 Building Code in Sweden, driving criteria for concrete piles based on stress-wave theory were introduced, as summarized in Table 1. The driving criteria are intended for 3 and 4 tonne gravity hammers. For hydraulic rigs, which have free-falling hammers, the drop height indicated should be reduced to 80 % of the values in the table. The criteria were considered to include a safety factor of 3,0. For 330 - 450 kN pile load, pile with a standard a cross sectional area of 235 mm x 235 mm was used. For 600 kN load, the standard cross sectional area was 275 mm x 275 mm."

Jan 1, 2014

By Khamis Y. Haramy

Quality assurance and quality control of drilled shafts has become a concern due to difficulties in accurately locating construction anomalies and determining load bearing capacity of defected drilled shafts. Various non-destructive evaluation techniques have been developed to estimate the integrity of the concrete in drilled shafts. While these techniques have been widely accepted, variables and unknowns can affect the measurement results. Results are typically difficult to interpret, leading to unnecessary construction delays and possible litigation over shaft integrity. In addition, influences of surrounding ground materials, stress states under different load conditions, and crack and residual stress development during concrete curing further complicate determination of shaft performance. This paper focuses on the evaluation of load bearing capacity of defected drilled shafts under various conditions by numerical analysis and modeling.

Jan 1, 2007

By David V. Lewin

Heavy structures in central Cleveland, Ohio, are supported on raft foundations, driven piles, or caissons. Settlements can be predicted and structures are designed to accommodate such settlements. On one project the settlements were not provided for in the design of the structure. Soils are sands, silts, and varved clays to shale. A rift in a central area is 600 feet deep. Solutions to problems, and results, are detailed.

Jan 1, 1985

By Hessam Yazdani

In comparison to the conventional piled foundations, the piled-raft foundations provide a more economical solution to support high-rise buildings constructed on soft soils. In this type of foundations, the bearing capacity of the underlying soil is taken into account to support the superstructure loads and the piles are placed to control both the total and differential settlements of the superstructure. Currently, there is not a standard and worldwide acceptable approach to select the location of the piles and most of piled-raft foundations are designed based on the experience of designers. Therefore, particular attention should be given to the optimal design of this type of foundations in order to minimize the considerable construction costs involved. This paper examines the capability of the ant colony optimization (ACO) algorithm to optimize the piled-raft foundations subjected to static and seismic loadings. The soil-pile interaction is considered by modeling the side and tip resistance components of the piles using the nonlinear Winkler-based p-y and t-z curves in the OpenSees program. The soil-raft interaction is taken into consideration using the Winkler springs beneath the raft. The objective of the optimization problem is to minimize the construction cost of the foundation by taking the configuration and number of the piles as design variables. The side and tip forces of the piles as well as the total and differential settlements of the foundation under the serviceability limit state are considered as the constraints for the optimization problem. Results show that in addition to the type of analysis (linear/nonlinear), the regard or disregard of the soil-pile interaction in the analysis can significantly change the optimal solution. The optimal solutions obtained match the engineering expectations and indicate the effectiveness and capability of the ACO algorithm to minimize the construction cost.

Jan 1, 2013

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By Karsten Beckhaus

"Abstract Tremie concrete for special geotechnical works needs special properties, especially during the casting process. Today’s execution standards for bored piles and diaphragm walls, EN 1536 and EN 1538, as well as the draft version of concrete standard EN 206, all comprise regulations for deep foundation concrete which have not been changed for decades. Considering the recent development in concrete technology at the same time and its actual state-of-the-art, it is essential to develop new normative specifications and specification requirements.GeneralTo allow the required integrity and quality after placing and hardening, concrete for structural elements like bored piles or diaphragm walls, used as foundations of high-rise buildings or as retaining structures for large and deep building pits, must have adequate workability and stability.In addition to requirements on mechanical properties and on durability, both of which have increased within the last decades, concrete must be suitable for being cast in deep or extremely deep excavations, see figure 1. Today’s specialist foundation engineering machinery makes it possible to drill or cut down to in excess of100 m depth. Concrete technology has developed and allows the use of high performance concrete for deep foundations. But is this capability represented by actual regulations?It has become very common for the industry to supply or use concrete with low water cement ratios, nevertheless highly flowable and set-retarded for several hours if needed. Very low water cement ratios allow design strength of 60 MPa or higher (Larisch, 2011), and a very low porosity which is required for a long service life in aggressive conditions, e.g. by chlorides.To achieve best performance, it is obvious that the concrete must completely fill the excavation and fully embed the reinforcement. As vibration of deep foundation concrete is (usually) not allowed and was anyway inefficient, deep foundation concrete must be designed to self-compact under hydrostatic pressure. Generally, it must be considered that after placement the concrete’s quality cannot be influenced anymore. Therefore, both the pouring procedure and the concrete quality must be adequate."

Jan 1, 2014

By Ray. K. Filip

The concept of installing a steel sheet pile retaining wall into the ground by "pressing" has resulted in the development of various equipment solutions over the last thirty years e.g. Taylor Woodrow ?Pile Master', Giken 'Silent Piler" & Tosa 'Still Worker?. Dawson Construction Plant Ltd (DCP), have recently advanced the pile pressing concept with the introduction of their 'Push-Pull' system. This advancement offers significant improvements in the quality of installation compared with traditional pressing solutions but also greater versatility, higher productivity and, most importantly, generates new opportunities through a wider range of applications for "silent piling'. This paper will focus primarily on the use of the Push-Pull concept in the construction of a unique "integral" bridge in Milton Keynes, England. Finally, the paper touches on the development of quiet, vibration-less pile extraction equipment, which allows steel to be considered the foundation material of choice for truly sustainable construction. It is no longer acceptable to leave unwanted piles in the ground.

Jan 1, 2006

By Jason N. Scott

CFA piling is a ?blind? construction process that relies heavily on the rig instrumentation to produce sound piles. If the data measured and recorded during construction can be made available to engineers and managers within hours after construction then there are many economic and quality control benefits that can be realised. A state of the art CFA instrumentation and data management process has been developed in the UK. The key components of the instrumentation, GSM data service and the central database are described. Many benefits to the business have been realised and, where possible, these are quantified.

Jan 1, 2006

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By Matthew Janes

Quality control procedures are increasingly important with today's higher capacity foundations and complex loading conditions. The need for a mobile, repeatable, nondestructive and economical load test method led to the development of an entirely new approach. The system described involves using solid propellant fuels to accelerate a reaction mass off the test pile. The force required to accelerate the reaction mass upward acts equally downward on the pile. Very high forces may be applied to the pile in a controlled, linearly increasing manner. The duration of the applied load is approximately 100 milliseconds. This rate of loading is slow enough to allow the pile and soil to react together as a composite rigid body. Pile/soil accelerations and velocities are low, typically 1 g and 1 m/s respectively. The effects combine to produce pile and soil response no longer dominated by the transfer of force via stress pulse (as with impact). Instead the pile force increases throughout the length of the pile, with pile top and toe stresses building in unison with time. This emulates the stress condition during static pile loading. Finally, state of the art instrumentation systems are used to obtain test data. Displacement is monitored directly using a laser datum and integrated receiver located at the centre axis of the pile. Force is also monitored directly using a calibrated load cell. Data is acquired and digitized using a 386 PC with user friendly software capable of producing load deflection curves and time histories in the field seconds after testing.

Jan 1, 1990

By Shaw-Shong Liew

This paper presents the processes of investigation, analysis, design, construction and monitoring of soil nail stabilisation work to facilitate a 14.5 m deep excavation at an uncontrolled fill ground. An extensive instrumentation programme had been implemented to monitor the performance of the stabilisation solution, to provide validation for the designed nail resistance and groundwater variation. From the monitoring results, it was proved that the soil nail stabilisation technique is effective for loose saturated fill provided that substantial care is taken during implementation. Construction difficulties, solutions to overcome the problems and lessons learned will be discussed in the paper.

Jan 1, 2006

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By Frances Badelow

This paper describes a design process for piled raft foundations supporting high-rise buildings. The design process comprises an initial stage of geotechnical site characterization using the results of investigation boreholes to prepare a subsurface model and derive geotechnical parameters for raft and pile design from empirical correlations. Following this a preliminary analysis is undertaken using a combination of elastic theory and allowances for non linear behaviour of the piled raft system to assess the viability of such a foundation system and any potential advantages of a piled raft over conventional fully piled foundation systems. Finally, a detailed analysis is undertaken using the GARP8 computer program. Case studies where this design process has been successfully used to design a more efficient piled raft system that has resulted in significant cost and time savings compared to conventional bored pile foundation options are also described.

Jan 1, 2006

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

Jan 1, 2000

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988