Search Documents

By Heman Manchanda, Sandeep Sharma

Several infrastructure projects are in various stages of construction and planning in India and almost all of them involves open ground excavation extending to varying depths. These structures are generally multipurpose and fulfil several needs of the society, their failure can be catastrophic. The design and construction of deep open excavations is generally associated with a high level of risks due to a whole series of uncertainties involved, and the success of such projects depends on various factors including appropriate evaluation of ground behavior and response to excavation stages, correct choice and analysis of construction supports, control of ground water flow during excavation, etc. One of the most critical amongst all these is ground water flow during construction and stability of underground excavation depends to a large extent on ground water control. This paper uses numerical studies for the assessment of the potential impact of ground water and ground water movement for the design of underground deep structures. The studies are being conducted using PLAXIS 2D finite element software and analysis all construction stages to which an open underground excavation shall be subjected. The paper discussed in detail the impact of water table fluctuations and comparative evaluation of different water flow conditions – a) Different Stages of excavation in line with the construction sequence (Phreatic), b) Coupled flow analysis (Transient- 1 year and 2-year duration) and c) Steady state flow conditions. The paper also covers seepage calculation and design of dewatering system.

Sep 1, 2022

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

By N. Schmitz

This paper explains how new digital solutions improve reverse circulation drilling operations. Upgrading field-proven reverse circulation drilling (RCD) rigs with new digital technologies enables semiautomated drilling, with upgrade options for fully automated & remote drilling. Key elements of the improvements are electrically controlled valve systems, process instrumentations, a state of the art machine controller and drilling operation via a touch control panel. Automation of core processes, such as adding drill pipes, reduces set-up times, increases machine uptime for drilling and as a result efficiency. While drilling, sensors provide continuous feedback, which is used to automatically adjust e.g. the weight on bit to the optimum; resulting in an increased rate of penetration and less wear and tear. While in the past hydraulic power packs (HPU) have typically been operated at a constant high-performance level with related high fuel consumption, a new interface between the machine controller and the power unit regulates the HPU performance exactly according to the actual drilling operation needs. This leads to significant fuel consumption reduction. The safety benefits of the digital improvements are the ability to remotely operate the rig in challenging site conditions via a mobile operator panel.

Sep 8, 2021

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By R. Gerritsen, Erwin de Jong, E. van der Velde, C. te Boekhorst

"In recent years the market for Mixed-In-Place soil mix techniques in the Netherlands has been growing rapidly. Initially the technique was used to create cut-off walls near river dikes and as a vibration free method to create retaining walls for building pits. Studies have been undertaken and projects are executed in order to strengthen the dike itself by the use of Mixed-In-Place techniques. In February 2012 Bauer Funderingstechniek started the construction of the first polder in the Netherlands with their approved Mixed-In-Place cut-off walls. This article explains the background of the use of this cost-effective and durable construction method and discusses how the challenging requirements from the client were fulfilled, both in design and execution. The quality assurance and quality control consisted of preliminary soil and mixture investigations, extensive measurements during construction and leakage detection through geophysical methods. The information is presented in 3 case histories, all subprojects of a large infrastructural project ‘Leeuwarden Vrij-Baan’ in the Netherlands.INTRODUCTIONThe Netherlands have a worldwide reputation in creating their own country by reclaiming land from the sea. Since the 15th century the Dutch have been creating “polders”, areas of reclaimed land below sea level, surrounded by dykes and with a mechanically maintained water level. In the 20th century the use of artificial polders became an interesting construction method for creating underpasses below motorways and canals using watertight geomembranes to create an impermeable layer that separated the polder from its surroundings. These kinds of structures have one big disadvantage, they need a lot of space. The main idea of such a structure is that the upward water pressure under the geomembrane has to be in balance with the remaining soil on top of it. For this reason, the geomembrane has to be placed at a depth significantly deeper than the polder surface, depending on the hydraulic head in the aquifer. Slopes of 1:3 (1 vertical : 3 horizontal) are most commonly used, resulting in very large open excavations and massive earthworks, even for relatively small underpasses. Special measures can be taken to reduce the spatial use with vertical limits, but these measures will increase the building costs (Gerritsen et al. 2014)."

Jan 1, 2015

By Clifford Taylor, Alexander Zöhrer

"The execution of deep basement excavations under narrow conditions is one of the most challenging tasks in geotechnics. The vicinity of neighbouring buildings, roads, and underground structures such as sewers or power lines, quite often prohibits the application of standard solutions. In addition, legal considerations in the use of adjacent properties is becoming increasingly difficult. This paper will present some innovative approaches to overcome the above-mentioned challenges based on several case studies from central Europe. For every project the design approach as well as the techniques used for execution will be explained, detailing both the advantages and the limitations of the applications. One case study shows a deep basement excavation (approx. 17m) in the centre of Prague, Czech Republic. This project featured many challenging boundary conditions (narrow construction area, high ground water table, jet grouting column embedment into bedrock, constraints regarding use of ground anchors due to property rights, etc). The realisation of the complex design is described and illustrated in detail. Other case studies will show the combined application of bored piles with jet grouting and also explain the design of vertical prestressed anchors for retaining walls.INTRODUCTIONThe development of urban areas has always presented challenges, from access for equipment and materials to the rectification of existing foundations in unknown condition. Compounding these is the increasingly stringent requirements to retain, maintain and reduce impact on culturally and historically significant structures. As available space is becoming more limited, optimisation of real estate has resulted in buildings getting higher and their basements deeper below ground. Two or more basement levels are quite common, with typical excavation depths ranging from 5 to more than 10m. Additionally, we are faced with neighbouring buildings that are equally high, deep and massive. These buildings directly adjacent the retaining structure require underpinning to limit settlement, and in cases where they are within just a few meters, this building mass generates additional earth pressure for the retaining wall to support, resulting in complex loading cases.This paper highlights several common challenges and explores the measures implemented to overcome them. The challenges and examples of either design based solutions or practical applications will focus on the following topics – the limitations of conventional geotechnical construction methods, overcoming challenging geology and the requirement for watertight basement constructions."

Jan 1, 1900

By Rich A. Lamb, Paul J. Axtell, Michael K. Muchard

"Since 2010, the Minnesota Department of Transportation (MnDOT) has performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. All of the piles were 42-in diameter, open-ended pipes driven to practical refusal on sedimentary bedrock with D125-32 diesel hammers from three separate manufacturers. The rapid load test method in general accordance with ASTM D7383-10 (Statnamic method) was used along with high-strain dynamic testing and subsequent signal matching. Results of these tests indicate that the axial nominal resistance of these piles in compression is not controlled by geotechnical considerations when driven with an appropriately sized hammer and installation criterion. Rather, the predominantly elastic load-deflection behavior of the piles under compressive load suggests the axial nominal compressive resistance is controlled by the structural capacity of the pile. In all instances, the rapid load tests indicated a nominal resistance exceeding that produced by high-strain dynamic tests due to insufficient hammer energy to fully mobilize resistance. In all cases, the hammers used were able to easily install the piles through the soil overburden. Mobilizing a larger hammer simply to demonstrate high-strain dynamic resistance is not economical or practical. This paper presents the subsurface conditions at each location, the ensuing test results, and the ramifications for future projects in Minnesota utilizing large-diameter open-ended pipe piles.INTRODUCTIONThe Minnesota Department of Transportation (MnDOT) has recently performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. The four project locations described in this paper where pile load testing was performed are shown in Figure 1 and exist in the southeastern portion of Minnesota. The projects are all major bridges crossing the Mississippi River in three instances and the St. Croix River just above the Mississippi River in the other instance. The first project is the TH 61 Mississippi River crossing in Hasting, MN where two load tests were conducted. The second is the TH 36 St. Croix River crossing in Stillwater, MN where two load tests were performed. The third project is the I-90 Mississippi River crossing in Dresbach, MN where three load tests were conducted. The final project is the TH 43 Mississippi River crossing in Winona, MN where one load test was performed."

Jan 1, 2017

By Craig H. Olson

"A new ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary.New Approachway RampThe PDA testing began at the new dock approachway ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Craig H. Olson

"Anew ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary. New Approachway RampThe PDA testing began at the new dock approach way ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Remco Offenberg, Marcel Bielefeld, Martijn van Delft

The question of the continued suitability of existing foundations arises when the function of the superstructure changes. This can occur when the superstructure is replaced or when the existing structure is expanded, leading to higher loads on the existing foundation. Quite often it is a challenge to define the suitability (with respect to integrity, bearing capacity or both). The lack of information on the existing foundation (such as pile dimensions, installation records, original soil investigation, design calculations, etc.) makes it frequently seemingly impossible to assess whether the foundation or foundation elements can be re-used. The paper outlines the tools available to an engineer to evaluate existing foundation piles for potential re-use. The paper illustrates the application of these tools through a few case studies from The Netherlands, including the evaluation of a 400 years old bridge foundation to address increasing traffic loads.

May 1, 2022

By Brandon Smith, William Bohlen

Riverbank erosion along the Brazos River has modified the structural support conditions for an existing bridge structure in Southeast Texas. The 8-span, 1,200-foot long bridge was completed in 1992 along Highway 99, a key corridor for the Houston area. Foundation support conditions have been altered due to natural, ongoing river morphology for three bents on the affected riverbank. Recent events include three storms within a three-year period that each exceeded the 500-year return probability. This resulted in accelerated erosion along the northern riverbank. Over forty vertical feet of soil has been removed in some locations. Drilled shaft foundations are now functioning as columns. This review considers the behavior of columns and deep foundation elements due to the modified support conditions. The review ultimately presents a rational methodology for the review of the present and anticipated future bridge configuration with respect to current strength, service, and extreme event limits, with corresponding safety factors for the design. Introduction and Background The Fort Bend Grand Parkway Toll Road Authority (Owner) oversees the State Highway 99 Judge Jodie Stavinoha Bridge over the Brazos River. The 8-span, 1,200-foot long bridge was originally designed with four southern approach spans of 115 feet; a three-span continuous river crossing with span lengths of 195 feet-235 feet-195 feet; and a single northern approach span of 115 feet. Figure 1 provides an overview of the northern portion of the bridge. Table 1 provides a summary of the original bridge substructure configuration. When the bridge was completed, the centerline of the Brazos River was located at midpsan of the main span and the northern high bank was originally located at Bent 7. Erosion process has forced the northern high bank to Abutment 9 (also called Bent 9), and the river centerline during normal flow conditions is located south of Bent 8. The overall estimated river excursion at present day is approximately 270 feet to the north from its original location. An erosion wall that was installed in 2017 limits further erosion of the north river bank within the 300-foot width of the roadway corridor right-of-way. This study was developed to better understand the existing conditions, and to forecast the need, nature, and criteria for potential future improvements.

Jan 1, 2019

By Srijit Bandyopadhyay, Aniruddha Sengupta, G. R. Reddy, Raj Banerjee

The objective of the present endeavor is to compare the performance of a pile raft system in foundation sand subjected to lateral loads. To study the behavior of pile raft system in sand a laboratory test was conducted on small scale model foundation system. The raft and pile was modeled by square concrete foundation of 250 mm x 250 mm x 15 mm in length, breadth and thickness and 25mm diameter and 250mm long circular pile located at the center of the raft. The system was tested under static lateral loads of 6.25N, 12.5N, 18.75N and 25 N respectively resting on dry Kasai River sand. A vertical surcharge pressure of 1.5kPa (10 kg) was applied on top of the model raft for each case. The results of the model tests have been simulated by a general purpose 3-D finite element software and the model has been validated with experimental results. The moments of the pile obtained from the model tests and those predicted by the numerical analyses for all the lateral loads matches reasonably well. For matching the trend of bending moments obtained from experiments, validation with theoretical results have been done with the help of Matlock and Reese (1960) approach for a single value of lateral loading. Moreover, a parametric study has been conducted with 5mX5mX0.3m raft size with 0.5m diameter and 5 meter long pile with increasing number of piles namely 2, 5 and 9 respectively to study the response in terms of moment and lateral deformation under available earthquake loadings, like Loma Prieta (1989) and Darfield Christchurch (2010). Bending moments of piles and load deformation curves for lateral loading have been studied for each case in which it is observed that the bending moments of pile significantly reduces (around 4 times) as the number of pile is increased to two, but it decreases to a nearly constant value (it saturates) as the number of pile is increased to five and nine. Moreover, the lateral deformation of piled raft system drastically reduces (around 2.4 times) for two pile system, and it saturates to a constant value with five and nine pile system. All these results indicate the constancy of stiffness irrespective of the number of piles in the piled raft.

Jan 1, 2015

By Stuart Coutts

"This paper presents an overview of the author’s experience related to the assessment of the base capacity of straight shafted and enlarged-base bored piles in sand. A design approach based on CPT qc is described which has been calibrated using a database of load tests. The importance of correct installation techniques with instrumentation are illustrated and a discussion is presented on the current use of high strain dynamic testing to validate compliance with design. An example of a recent project with high quality instrumented load test data illustrates the close match to the proposed best practice approach and also highlights the importance for consideration of the effects of stress relief for deep foundations installed in deep excavations.1 INTRODUCTIONContinuous Flight Auger (CFA) piles are the bored foundation pile of choice for sand deposits across Australia. The evolution of the determination of the base resistance of CFA piles has been shaped by available investigative techniques, calculation methods, and calibration of designs with laboratory and field testing. The Cone Penetration Test (CPT) has been widely used in Western Australia (WA) where the test has been commercially available via multiple contractors for more than 25 years. On the East coast, the adoption of CPT testing has been slower with a transition from traditional Standard Penetration Testing (SPT) still occurring. Dynamic pile load tests are often used to derive parameters. The influence of pile installation on performance is commonly misunderstood and is an important element on any discussion of pile capacity for CFA pile types. The interface between the base of the constructed pile and the in-situ soil has an influence on capacity such that a poorly constructed pile base will have limited (if any) contribution to pile performance within the normal working range, generally within a 10 mm movement. The research presented in this paper pertains to CFA piles (no drilling fluids) and enlarged base piles constructed using CFA techniques under drilling fluids such that clean pile/base interface is targeted. Developments in modern piling equipment and instrumentation allow the pressure and volume of delivered concrete/grout to piles to be accurately monitored at various stages of installation such that repeatable ‘best practice’ can be achieved. The changes in soil conditions that occur due to the disturbance of the install technique are also important.Although the results of this research are likely applicable to bored piles, the interface between the pile and in-situ soil (shaft and base) need to be considered for various installation techniques. The effects of stress relaxation (due to removal of soil above pile base and adjacent shaft), time to concreting, and the zone of disturbed soil around the pile shaft are paramount.2 INSTALLATION CONSIDERATIONS The pile mix (concrete/grout) and interface with the in-situ soil are also an important consideration. For example, coarse grained, poorly graded, dry, clean sand will be partially permeated by most pile mixes; such that the influenced soil will be enhanced and in instances the overall effective pile dimensions increased. Permeation of the disturbed zone of a pile or anchor shaft along with scale effects (Lehane 2009) can have significant effect on shaft capacity and shaft frictions significantly exceeding expected are not uncommon based on ‘theoretical’ dimensions. Advancements in mix technology and mix techniques also have a large influence on the pile/soil interface. The ability of the piling rig and augers to excavate a plumb and gauge hole can also have a large influence on the zone of soil disturbed adjacent the constructed pile with a resulting influence on capacity."

Jan 1, 1900

By Francisco A. Flores, Rigoberto Torres

The Complementary Technical Standards of Mexico’s City Building Code do not mention the criteria to compute the bearing capacity of Steel H-piles. It is necessary to increase knowledge in using steel H-piles as foundation elements in very soft soils of Mexico City. Considering their applicability to reinforce structures as well as new foundations in confined spaces, this research is proposed to obtain the axial load capacity of piles at scale in laboratory. This paper describes the construction and testing of scale models in laboratory of steel H-piles to measure their axial compression and tension load capacity in the soft soils of Mexico City. Three types of piles were fabricated at scale. Tests were performed on individual piles and pile groups. Based on the axial load tests, the load-displacement curves are presented both in compression and tension. The analysis of the results is shown, and comments are given regarding the ultimate bearing capacity of piles. Recommendations are presented regarding the determination of the bearing capacity of these piles in the very soft soils of Mexico City.

Sep 8, 2021

By Scott Dodds

"The Oxford Hydroelectric Station was a unique project that incorporated a variety of dam strengthening methods to stabilize the facility in order to meet the standards required by Federal Energy Regulatory Commission (FERC). The dam stability and Probable Maximum Flood (PMF) remediation work consisted of (1) construction of a new emergency spillway; (2) installation of 75 high capacity rock anchors; (3) construction of an anchored concrete powerhouse buttress; (4) construction of cast-in-place and sheetpile flood walls; and (5) design and construction of a permanent soil nail wall. INTRODUCTIONThe Oxford Hydroelectric Station is one of 11 hydroelectric facilities owned and operated by Duke Power along the Catawba/Wateree River. The Catawba River originates in the foothills of the Appalachian Mountains just west of Morganton, North Carolina. The river flows east out of the mountains and, at a point just below the Oxford Dam, the Catawba River turns and heads southeast. The Catawba River continues to flow southeast past Charlotte and into South Carolina where it eventually becomes the Wateree River. The Wateree River eventually flows in to the Atlantic Ocean.Located a few miles east of Hickory, North Carolina, the Oxford Dam and Hydroelectric facility is in the upper reach of the Catawba River. Oxford Dam creates the third impoundment along the river known as Lake Hickory. Lake Hickory is well known locally for providing many outdoor activities such as boating, jet skiing, canoeing and fishing. The dam and powerhouse were put into operation in the spring of 1928.Key features of the dam include a short embankment section on the south end of the structure, a 391-foot (119m) long south bulkhead and powerhouse, 540-foot (165m) long gated spillway section and a 235-foot (71.6m) long north bulkhead. The maximum height of the dam is approximately 100-feet (30m) from the crest to the dam/rock interface. (See Figure 1).The work associated with this project is the result of licensing requirements of the Federal Energy Regulatory Commission (FERC) which mandates that all hydroelectric facilities have the capacity to safely discharge runoff created by a critical rainfall event defined as the probable maximum flood (PMF). Duke Power, a division of Duke Energy (DUKE) submitted an initial PMF report in 1992 which indicated that at the Oxford Dam would be overtopped by approximately 10-feet of water during the modeled PMF event. Given the duration and depth of the overtopping, significant damage to the facility and a possible breach could result. Therefore, modifications to the existing facility were necessary to satisfy the report of the PMF model."

Jan 1, 2005

By Hitendrabhai S. Dewangan, Dr. Aashish A. Mehta

Pile foundation is widely used in construction of marine structures. In offshore & marine piling work, drilling/boring supporting fluid is used to stabilize the borehole (excavation) prior to tremie concrete. The poly-fluid is a synthetic drilling granular polymer characterized by high molecular weight.it is mainly used for the preparation of stabilizing and lubrication mud in drilling of deep foundations. Disposal of polymers after using it into the sea, pollutant the sea environment, which may be harmful for living organisms inside sea. To reduce the pollution in offshore/Onshore, it is essential to take the precautions during flushing operation with proper recycled, reused & it’s Disposal. To provide economic and environmental solutions, used slurry was treated with addition dose of fresh material/polymers. The amount of fresh materials/ Polymer to be added can be decided based on (viscosity, density and pH value) test results. Finally, initiate water flow and air agitation as required. Run the tests on the re generated slurry before transferring to storage tank. Also, after storage, polymers will be reused for next operation. Moreover, mud wastage coming from borehole will also be disposed at suitable dumping places.

Sep 1, 2022

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan PhD

The experience gained during more than 900 Crosshole Sonic Logging (CSL) tests on drilled shafts shows the importance of establishing proper project acceptance and repair protocols. Drilled shaft evaluation is a multidisciplinary task that should not be left solely to the outcome of the CSL test. This test allows to characterize and delimit areas of different qualities of concrete, and it is important that all the interested parties understand the difference between flaws and defects. The information presented here is intended to give a guideline to contractors, inspectors, engineers, owners and clients on how to deal with acceptance and remediation of defective drilled shafts, detected using CSL tests. A database of flaws is presented depending on their location, intensity and remediation method. Procedures that allow the flaws to be analyzed are presented in order to dismiss or classify them as defects. In many cases, the CSL test may indicate an anomaly, but by coring the concrete and analyzing the structural demands and conditions, the flaw can be classified as non-severe. When flaws are classified as defects, their repair will depend on the area where they are located in the drilled shaft pile. In this document two procedures are described for repairing defects depending on their location. For defects in the drilled shaft head area, the procedure takes into account the interaction between the new and old concrete. For repairing the middle zone of the drilled shaft by grouting, the major concerns are the difficulty of accessing through the drilled shaft at deep depths and the communication between boreholes. For defects at the drilled shaft tip, two proposed remediation methods are presented. Finally, tomography tests are presented to compare the effectiveness of remediation by grouting.

Oct 1, 2022

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019