Search Documents

By L. W. Vollmer

Introduction During the past three years at least fifty strings of 9% nickel steel tubing have exhibited excellent resistance .to the variably severe corrosive conditions typical of many of the sweet condensate wells in Mississippi, Louisiana, and Texas. This experience, and the characteristically outstanding performance of other ?nickel alloy steels under hydrogen sulphide corrosive conditions, dictated the selection of 9% nickel steel tubing for the second well drilled in the sour condensate Pincher Creek field of southwestern Alberta. The damaging effects of the Pincher Creek reservoir fluids on well equipment had been manifested in the discovery well by the rapid and not yet fully understood failure of API Grade N-80 tubing, stainless steel wire lines, and alloy steel fishing tools. Two very unexpected failures in the 9% nickel steel tubing, after only six days of service in production tests, instigated an extensive and continuing investigation to ascertain the probable cause of failure. This discussion presents some of the results obtained thus far which cast a little light on the perplexing behaviour of steels in hydrogen sulphide environments in general, and in sour condensate wells in particular. History of Tubing Failures Walter Marr well No. 1, in which the 9% nickel steel tubing failures occurred, produces from the Madison lime at the depth interval approximately 12,200 to 12,750 feet. The gas-oil ratio is about 26,000 and the gas contains 10.2 per cent hydrogen sulphide and 6.3 per cent carbon dioxide by volume.

Jan 1, 1952

By D. McConchie

BauxsolTM, prepared by treating bauxite refinery residues with Mg2+ and Ca2+, has an excellent ability to remove arsenic from acidic waters. The addition of BauxsolTM to sulphidic waste rock at the Gilt Edge Mine, South Dakota, reduced As concentrations in leachate water from 35 mg/L to < 0.005 mg/L; the concentrations have remained below 0.005 mg/L for the five years since the treatment was initiated. However, ordinary BauxsolTM does not effectively remove As from near-neutral water and it needs to be acid-treated or blended with small amounts of reagents, such as jarosite or ferrous sulphate, to increase the proportion of positively charged binding sites on the particles. The use of a jarosite/BauxsolTM blend can effectively treat ponded water, and As(V) concentrations can easily be reduced from over 1 mg/L to < 0.001 mg/L; As(III) has to be oxidised to As(V) for effective removal. Metal contaminants in the jarosite are trapped by the BauxsolTM and only very small amounts of the As, or other elements bound during treatment, are liberated using a TCLP leaching test. The exhausted treatment reagents meet the criteria for classification as an inert solid and do not need to be disposed of in a secure repository.

Jan 1, 2006

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By J. S. Stachulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The first objective is to prevent a fife.The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife.The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife. Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By J. S. Stacbulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The flirt objective is to prevent a fife. The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife. The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife.Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By R. B. Fermor

"AbstractAttention is drawn to the ventilation problems arising from the use of diesel vehicles underground, especially in view of the fact that diesel fumes in combination with other pollutants may be more harmful than diesel fumes alone or the other pollutants alone.Means for minimizing the harmful effects of using diesels underground are listed, and the quantities of air' required in mines in which diesel-powered vehicles are used are discussed. Mines are classified in three categories on the basis of severity of ventilation problems, and statistics are given for these categories.Details of the various components contributing to total ventilation needs are given, and the ventilation needs of individual mines in the three categories are listed. A description is given of the principles according to which main ventilation coursing is planned and the selection and siting of main fans is discussed.General Considerations in the Use of Diesel-Engined Vehicles UndergroundIN ORDER to reduce physiological hazards, present and latent, to workers in mines in which extensive use is made of diesel equipment underground, it is important that mine ventilation systems reduce the concentrations of rock dust, diesel fumes and particulate matter as rapidly as possible to an acceptable level in all parts of the mine.There is some evidence that the long-term effects of a combination of the above pollutants are greater than those of anyone of them alone, which makes the problem even more pressing."

Jan 1, 1977

By R. W. Lawrence

"The management of acid rock drainage( ARD) to prevent impact when tailings are disposed of in the environment requires understanding of the phenomena giving rise to acidic drainage, a rigorous evaluation of the weathering characteristics of the tailings, and the successful implementation of control measures that will be effective in the long term. This paper provides a brief theoretical background to the complex reactions taking place in mill tailings containing residual sulfide minerals which must be appreciated to enable waste characterization program to be effective in predicting the future behavior of the tailings and in designing control methods which will work. The principals and practice of prediction and control as part of an ARD management strategy will then be discussed.Paper Not Available at Time of Publication"

Jan 1, 1997

By F. M. Doyle, G. Sidhu, A. J. Dussault, A. Raygani

There is a growing demand for rare earth metals for use in high strength permanent magnets, most notably Nd2Fe14B. Rare earth metals are extremely reactive, with reduction potentials around -2.5V SHE, and are conventionally produced by molten salt electrolysis. The current work was done to investigate an earlier report of electrodeposition of a neodymium ferroalloy from aqueous solution, to determine whether this approach could be an environmentally and economically competitive commercial approach for producing feedstock for permanent magnets. Such a process would be analogous thermodynamically to the Castner- Kellner process, in which aqueous sodium chloride brine is electrolyzed in cells with mercury cathodes. Metallic sodium forms an alloy (amalgam) at the cathode, thereby lowering the activity of the metallic sodium significantly below unity and making the reduction potential of sodium significantly less negative than the standard reduction potential. Here we report the effects of Nd/Fe ratio in the electrolyte, current density, temperature and two different complexing agents, glycine and cysteine, on the composition and morphology of the electrodeposits, along with current efficiency. The energy needed to produce neodymium as Nd:Fe alloys by aqueous electrodeposition was compared with values estimated for production by molten salt electrolysis and the thermodynamic energy requirement.

Jan 1, 2014

By R. M. BUCHANAN

The segment of Canadian industry based on smelting of alum in um and manufacture of consumer products is based entirely on imported alumina and bauxite. In the absence of Canadian bauxite deposits, consideration of anorthosite, a less desirable aluminous rock, is being undertaken as one alternative in maintaining assurance of supply. Anorthosites in Canada cover many thousands of square kilometres of the Precambrian Shield. Although compositions vary widely among Canadian anorthosites, many appear to exceed the specified minimum of 25% A I 20 3 in bodies containing more than the required JOO million tonnes. A lthough most Canadian anorthosites are of Precambrian age, one located in British Columbia has been identified as being Middle _Cretaceous.

Jan 1, 1984

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

During heap leaching of secondary copper sulphide ores operated at low heap temperatures and high levels of leach solution salinity, copper recovery is usually unsatisfactory, due to a slow chemical and bacteriological leaching of the covellite minerals either formed from leaching of chalcocite or naturally occurring in ores. A laboratory test program was conducted to investigate the effect of leach solution temperature in the range of 20 to 50°C on copper extraction during stirred reactor, bottle roll, and short column leaching of fresh or heap leached secondary copper sulphide ores. It was demonstrated that increasing heap temperature is an effective approach for improving recovery of copper from secondary copper sulphide ores. A review of the technologies available for heating heap leach solution or decreasing solution salinity to improve copper recovery from secondary sulphide ore indicates that an integration of copper concentrate pressure leaching with heap leaching is potentially a cost-effective approach. A copper flotation concentrate sample was tested through pressure oxidation with the use of heap leach solutions of varying strengths for the repulping of the concentrate in order to examine its effect on pressure oxidation performance. The test results indicate that use of heap leach solution of high salinity in the pressure oxidation process does not cause a negative impact on the process performance for copper extraction, sulphide oxidation, and recovery of gold (if present) from pressure leach residue, and has additional advantages of removing the bacterially inhibitory aluminum from heap leach solution and generating more acid and ferric iron in the pregnant leach solution. A flowsheet configuration for full integration of the copper concentrate pressure oxidation with heap leaching of secondary copper sulphide ore is proposed and discussed.

Jan 1, 2014

By J. Forster, C. A. Pickles, Mackowiak. K.

The future development of nickel laterite deposits is crucial with regards to satisfying impending nickel demands. The commercial implementation of new hydro/pyrometallurgical processes in recent years has led to significant improvements in the extraction of nickel from the laterite ores. One potential alternative pyrometallurgical processing route would be to selectively reduce the nickel and produce a concentrate with nickel contents similar to those attainable in the conventional flotation of sulphide ores. However, even bench scale studies have not yet been able to produce a high grade (>15% nickel) concentrate from a low grade laterite ore. The present research involved the microwave vacuum reduction roasting of a nickel laterite ore to yield a high grade concentrate, rich in nickel. Firstly, the effects of temperature and pressure on the nickel grade and recovery were investigated using a thermodynamic model. Secondly, briquettes containing a mixture of charcoal and a low grade silicate nickel laterite ore were reacted in a microwave vacuum system. The experimental variables studied were the input microwave energy, pressure and absorbed microwave power. Thirdly, the ferronickel in the reacted briquette was concentrated by magnetic separation and nickel grades of up to 21% could be achieved.

Jan 1, 2015

By F. McCarthy, W. Zhang, R. McDonald

"The processing of nickel laterites has been a topic of major interest at CSIRO for almost twenty years. During this period CSIRO has collaborated with other researchers and industry in developing a better understanding of existing processes and been actively involved in testing/developing new beneficiation and process options for these ores. The current paper summarises the results of selected studies and highlights improvements that have been achieved. Key topics to be discussed include enhancements in the mineralogical characterisation, beneficiation approaches, improvements in the understanding and application of leaching technologies, the development of synergistic solvent extraction (SSX) for the recovery of nickel/cobalt from laterite leach liquors and the collaborative development of the Direct Nickel process. Future opportunities and key research questions will be briefly examined.INTRODUCTION Nickel laterite ores comprise a significant resource in Australia and according to United States Geological Survey data nearly a quarter of world reserves are located there (USGS, 2016). More specifically, around 95% of Australian nickel resources (laterite and sulfide) are located in Western Australia (Australian Government, 2017). Given the recent closure of Queensland Nickel, essentially all of Australian nickel production occurs in Western Australia and the primary producers of processed nickel products include Nickel West (Kwinana) with ~84,000 t saleable nickel metal in 2016 (BHP Billiton, 2017), Minara Resources (Murrin Murrin) with 46,700 t nickel metal produced in 2015 (Glencore Australia, 2017), and First Quantum Minerals Ltd (Ravensthorpe) who sold 25,882 t nickel as mixed hydroxide product in 2016 (First Quantum Minerals, 2017). The total sales of nickel from Western Australia in the 2015-16 financial year were 175,722 t. The study of nickel laterites at CSIRO recommenced at the time second generation High Pressure Acid Leaching (HPAL) plants were being commissioned at Bulong, Cawse and Murrin Murrin in the late 1990’s. A combination of technical and engineering issues meant that the ramp-up times at these operations were slower than expected and the outcomes resulting from the attendant problems are well documented (e.g. Griffin & Becker, 2000; Reid & Barnett, 2002; O’Callaghan, 2003) while the issues faced at the BHP-Billiton-built Ravensthorpe plant have been addressed by the current owners of this project, First Quantum Minerals Ltd (Piper, 2012)."

Jan 1, 2017

By Xuanxue Mo, Zengqian Hou

"Abstract -Yidun Island Arc in Sanjiang Region is one of the important Kuroko-type volcano­ genic massive sulfide deposits (VMS) districts in southwestern China. Tectonically, the region is situated in the eastern portion of the Tethys orogenic belt, and is a late Triassic extensional island-arc. The island-arc underwent earlier arc construction, intra-arc rifting, later arc construction and back­ arc spreading during its evolution and formed a complete trench-arc-basin system, i.e., the Ganzi­ Litang suture zone, forearc basin, outer arc, intra-arc rifting zone, inner arc and back-arc basin from east to west across the island-arc.Kuroko-type VMS deposits and occurrences discovered so far are limited to within the intra-arc rifting zone of the Yidun Island Arc and tend to occur in groups or clusters distributed in separate fault­ bound basins; e.g., Zengke, Gacun and Xiangcheng basins, in which submarine volcanic rocks, especially bimodal volcanic suites, were extensively developed. The VMS deposits formed in the waning stages of volcanic eruption in the late Triassic and are hosted in the uppermost section of acidic volcanic rocks (rhyolitic-dacitic) within a bimodal suite. The orebodies are associated with these host rocks: rhyolitic-dacitic pyroclastic rocks and exhalites and chemical sedimentary rocks.Ali VMS deposits in Sanjiang are of the Zn-Pb-Cu type. The architecture of the deposits is two­fold, consisting of concordant lenses and layers of massive sulfides and an underlying discordant stockwork. Ali deposits show metal zoning. The hydrothermal alteration related to mineralization is strong and asyrnmetrical, and is found dominantly within the stockwork zone and host rocks surrounding the ores. There are two alteration patterns: (1) chloritization - sericitization - silicification from outer sides to core of the alteration pipe; and (2) silicification + sericitization - silicification + carbonate from the lower to upper part of the alteration pipe_The mineralization temperatures of ore-forming fluids vary in the range 200°C to 335°C. Thermal evolution of the fluids displays temperature profiles that first increase and then decrease with progression of mineralization processes. The majority of black-ore minerais (Groups I and II) formed during intensifying stages of hydrothermal activity, and the majority of serni-yellow-ore minerals (Group III) formed during a thermal maximum . There followed the formation of fine-grained black-ore minerals (Group IV), which interacted with barite layers during decreasing temperature phases.Oxygen and hydrogen isotope studies show that the sources of ore-forming fluids for the Kuroko­ type VMS deposits are two-fold: seawater and magmatic hydrothermal solutions, represented by the Kuroko deposits in Japan and Kuroko-type VMS deposits in Sanjiang, respectively. In the latter case the hydrothermal solutions reacted with host rocks and mixed with cold seawater percolating downward, and circulated through volcanic rocks resulting in development of alteration zones and formation of ore minerals in Kuroko-type VMS deposits."

Jan 1, 1993

By S. Foged

Umicore and MWH jointly demonstrated that mechanical dewatering of goethite and neutralised tailings significantly increased the life of a 30 ha tailings pond and improved the operation of the pond. Umicore operates one of its zinc production plants in Balen, Belgium. As part of its production process, an excess of neutralised and goethite¬containing tailings is generated. These have historically been stored inside large lined ponds. As the storage area of the current goethite pond was nearing its capacity, Umicore studied the potential for an extension to the existing embankment. However, this extension would face intense regulatory scrutiny, because the environmental and safety impacts were considered important. Together with Umicore, MWH suggested and investigated an alternative treatment approach consisting of mechanical dewatering prior to storage. A feasibility study was prepared where wet storage was compared to dry storage. Differences in safety risks, environmental impacts and economic costs were outlined. The study demonstrated that the life of the tailings pond could be increased from 6 to 22 years, seriously reducing the environmental impacts and safety risks at no significantly higher cost than would have been incurred with the continued operation of the existing pond. The results of the study are presented in this paper.

Jan 1, 2006

By W. N. Hamilton

As a result of a test-drilling program conducted by the Research Council of Alberta in 1968, a gypsum deposit averaging 30 feet in thickness, with a chemical purity of 84 per cent gypsum, has been proven to underlie the Clearwater River valley for a distance of 18 miles at depths ranging from near-surface to 300 feet. This and other subsurface deposits in the vicinity of Fort McMurray, Alberta are the product of local hydration of anhydrite beds believed to be the water-insoluble remains of the leached Prairie Evaporite formation of Middle Devonian age, the thick salt section of which is preserved down dip. The effects of salt solution are seen in the disturbed bedding and the intermixture of greyish green shale with gypsum in the core, the shale content being responsible for the rather low chemical purity of the deposit. A similar gypsum deposit, but probably of higher purity, is postulated to occur beneath the Athabasca River valley about 60 miles north of Fort McMurray.

Jan 1, 1969

By V. Gangrade

Recirculation is the major concern associated with the utilization of booster fans. In controlled recirculation, a portion of the return air is purposely mixed with the intake air and the mixture is directed towards a working district, while the air quantity and gas concentrations in the air are closely monitored and managed. The objectives of this study were to determine the gas concentration in intake and return airways during controlled recirculation, and to determine the recirculation fraction for multiple headings. Experiments were conducted in a laboratory model to determine the effect of controlled recirculation on the quality of air circulated through the working faces. Preliminary results showed that recirculation is beneficial to ventilation planning because it reduces the build-up of air contaminants at the working faces and reduces the overall power consumptions. The experimental results were used to quantify the recirculation fraction and to calibrate ventilation models of the laboratory model. These models are used to simulate the controlled recirculation and to predict the gas concentrations in multiple headings.

Aug 1, 2013

By Darren Medd

Kumtor Gold Company (KGC) currently operates the 500,000 tonnes per day Kumtor open pit gold mine located in the Issyk-Kul region of the Kyrgyz Republic at an elevation of more than 4,000 m. To supplement the open-pit mill feed with high grade underground ore from outside the current pit limits, KGC started pre-production design and development of the underground mine for the SB ore zone in late 2006. The initial phase of pre-production development consists of exploration and haulage declines which, upon completion, will provide ventilation and access to the underground mine. Design and construction of these declines presented many challenges to the project team considering the mines unique location at high altitude, the limited experience with Western underground mining techniques in the Kyrgyz Republic, and the impact of the nearby Davydov glacier and resultant ground conditions. Completion of the exploration and haulage declines was undertaken jointly by KGC and mine contractor, J.S. Redpath Limited (Redpath). The initial phase of development including several ground falls provided detailed information on geotechnical ground types and conditions that were useful in determining the overall mine design and methodology for production. This paper covers the various aspects of the design and construction process of developing the declines under the glacier, minimizing the likelihood of further ground falls, and the journey of both KGC and Redpath which led to the successful breakthrough between the declines on 01 July 2012.

Aug 1, 2013

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

By R. A. May, P. J. Brooks, W. M. Smith

"Neill and Gunter Limited (NGL) has prepared a preliminary design and a cost estimate for a ferric chloride leach plant to recover copper, lead, zinc, and silver from a typical complex sulphide ore. This plant design is specifically intended to treat unconcentrated ground ore (flotation feed), but can be readily adapted to treat bulk concentrates. Samples of ground ore and bulk concentrate were obtained from Heath Steele Mines, Miramichi, New Brunswick, laboratory testing, and preliminary process flow sheet preparation was carried out by the Research and Productivity Council in Fredericton, New Brunswick. Approximately thirty drawings have been produced, including process and equipment flowsheets, process piping and instrumentation drawings, and preliminary general arrangements. Preliminary capital and operating cost estimates were prepared for a plant that would treat 1000 t/d of crushed and ground ore to produce about 30 000 tpy of zinc. Capital and operating cost estimates were also projected for plants up to 4000 t/d of processed ore. Recoveries of 99% for zinc, 98% for lead, and 96% for copper were achieved in laboratory tests on unconcentrated ore. These recoveries were higher than the overall recoveries obtained from bulk concentrate, yielding approximately 10% more revenue.A 1000 tonne per day plant was determined to have a low return on investment, however, depending on the size and type of mining operations employed and the FCL plant throughput. DCF-ROI projections of 20% to over 30% were calculated for 100% equity financed “green field” mine, mill and FCL plant operations of 2000 t/d and higher"

Jan 1, 1997