Search Documents

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

By E K. Leeka

Process control limitations have led to suboptimal performance of the crushing section of Sishen MineÆs Jig Plant. The performance of the PID (proportional-integral-derivative) controller implemented during commissioning was hampered by the relatively small buffer capacity between the crushers and screens. The inability to maintain the tertiary crushing chamber under full choke conditions lead to inefficient crushing and reduced crusher product cubicity.Model predictive control (MPC) was implemented in the tertiary crusher plant in May 2012 and resulted in a throughput improvement of six per cent in its first month. The controller was further optimised and indicated a throughput improvement of 16 per cent during on/off testing in July 2012. The throughput improvement is attributable to the finer crusher product resulting from operating the crusher under full choke conditions and controlled feed rate to the tertiary crusher plant screens. The next step is to couple the model predictive controller, automated gap control system and an economic optimiser to ensure maximised throughput and value from the resource.CITATION:Leeka, E K, 2013. Performance of model predictive control on the crushing circuit at Sishen Mine, in Proceedings Iron Ore 2013 , pp 417-420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

B. P. Thomson (South Aust. Dept. of Mines): Dr. A. B. Edwards presents in the published discussion on the above paper, his interpretation of the dolerite dyke-lode relationship as a major objection to the syngenetic origin for Broken Hill ore bodies to which Mr. Condon subscribes.Dr. Edwards claims that the dyke-lode relationships indicate clearly that the Broken Hill orebody was formed after the folding and regional metamorphism of the Willyama Series. Field evidence compels m:e to join with H. F. King (1958), in finding this conclusion unacceptable-as follows:(1) Broken Hill type mineralization, as defined by King and Thomson (1953), is clearly confined by the regional sillimanite isograd and does not extend into the lower temperature almandine and biotite zones as does the Thackaringa type mineralization.(2) In the Corruga area the writer has mapped a dolerite dyke apparently cutting a conformable quartz gahnite lode of the Broken Hill type (see Edwards 1958, p. 12).(3) At the Champion mine a similar lode is cut by a fine grained granite dyke.An alternative history of the dolerite dykes to that given by Stillwell & Edwards (1956, p. 26) appears possible. It has been suggested by the writer in an unpublished thesis, (Thomson 1955, p. 30), that the pyroxenite and serpentine plugs and dolerite dykes are rheomorphic end-products of a complex regional metamorphic and metasomatic process involving the formation of amphibolite and pegmatite. The analogy in composition between the dolerite and normal amphibolite is close (see Edwards 1958, Fig. 1, p. 22).

Jan 1, 1959

Laboratory flotation tests on sized fractions of a certain number of selected minerals with homologous fatty acid derivatives (i.e. sodium salts and amine acetates) confirm that the higher homologues are more efficient collectors than the lower. Tests were carried out on sized material and finer size fractions floated at lower collector concentrations.It is suggested that selective flotation is best achieved with the reagent which most readily floats the most friable mineral in the ore, and that grade of product will be improved with the lowest usable homologue.INTRODUCTIONFlotation of non-sulphide minerals with fatty acids as collectors is usually less selective than the flotation of sulphide minerals with xanthate collectors. It is common to use the gradation in collecting power of homologous series of xanthates, as well as the more specific effects of activators and depressants, to achieve the separation of sulphides.The original aim of the work was to ascertain whether sodium salts of fatty acids (anionic) and fatty amine aceta:tes (cationic) could be selected from a homologous series to achieve better selectivity in separation of nonsulphide minerals by flotation. Subsequently the importance of friability of minerals in selective flotation was observed and the aim was expanded to develop a more practical approach to the testing of ore.MATERIALS USEDMineralsA series of massive mineral specimens, as pure as could be obtained, was procured. The specimens were cleaned by removing extraneous material, and then crushed and dry...

Jan 1, 1965

The dynamic response of holdup in a continuous ball mill has a direct influence on the rate function of grinding kinetics and is useful for predicting the variation in the size distribution of the finished product with time.A model was proposed involving three interacting, completely mixed chambers and this was used to derive analytically the transfer function of the system, from which the unit impulse response and the unit step response of the holdup with feed rate were obtained.The theory was confirmed by comparing it with previously published experimental data for the residence time distribution of particles passing through a ball mill.

Jan 1, 1975

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By Davis RA, Wasp EJ, Cowper NT

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New- York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering' this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three-year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1969

Statistics on the imports of industrial minerals into the EECshow that the traded volume in 1987 is approximately 23 million tonnes.The following table documents the imported quantities on the most important industrial minerals.

Jan 1, 1989

In this paper, the scientific bases of creation of simulation modelling systems of excavator-truck-conveyor complex work are represented. During the simulation modelling process of big mining and transport systems work the strict and full account of an order and sequence of all operations of simulated process is carried out. Step-by-step fixing of mining and transport system elements condition - excavators in loading and unloading points, trucks, road section, unloading points in storage bin, crushers and conveyors is conducted. Work and idle time of system elements are considered. During modelling process the information characterising system work as a whole is collected. It allows us to establish qualitative and quantitative influence of each system element on the final results of its functioning and provides to estimate rationality of a particular organisation variant of mining and transport equipment interaction from technological positions. Simulation results are: economic and technological indicators of mining and transport complex functioning of the period for each subsystem, as well as on the road, the points of loading, unloading and reloading.

Dec 6, 2010

The extent of regional stratigraphic and structural geological mapping so far carried out in Australia is likely to be greatly overestimated by uncritical inspection of the latest authoritative geological map of the continent-that so ably compiled by the late Sir'T. W. Edgeworth David. Vast areas geologically coloured on this map are in fact known only from the most meagre field data, some of Which even include observations of distant views from which the so-called "geology" has been indicated in' reconnaissance reports.This applies to large areas in Cape York Peninsula; the plateau of Arnhem Land, and its margins except on the west where the Pine Creek mineral belt is better known; to the Desert Basin of Western Australia, practically the whole of the western half of the Northern Territory, much of east-central Western Australia, and northwestern New South Wales. Other vast areas are, more happily perhaps, left blank. It is true that prospecting parties have, at various times and with varying degrees of thoroughness, traversedparts of these little-known regions, often, however, in the search for gold or the.more obvious types of metalliferous mineral deposits and, furthermore, too often without leaving any written account of their examination, or with very sketchy details supplied. Unpublished geological surveys also cover some parts of these regions, but, on the whole, the picture we can draw of the regional deployment of rock masses in Australia is far less full than even David's map, with its obvious blanks, presents to us.Lest the practical mineral seeker among us should be inclined to place too much reliance on the prospecting to which I have referred.as giving him a straight hint of what country to keep out of, we may point to the recent discovery of a major sedimentary basin in the east KimberllilYs on which Dr. Teichert will have more to say. And that there are new metalliferous mineral deposits to be foundin parts of these little-known areas no one can doubt, for, after all, new discoveries are made from time to time in areas so well-known as the Victorian gold-fields. I take it then that regional geological mapping is a necessary concomitant of the further development of Australia's mineral resources-but I am not of the school that places it first on the list of priorities, and furthermore I believe that there can be a royal road to regional mapping-an inspired approach based on knowledge already gained and led to fruition by field surveys in key areas, by which there may be obtained a result giving a significantly close approach to actuality with only a fraction of the work that would be required for detailed field surveys on a systematic basis. I believe that a policy of rapid reconnaissance of such a type should be adhered to, especially in view of present deficiencies in numbers of geologists available for all purposes in Australia. The details that must eventually be sought can, I believe, be filled in later as the whole country becomes more developed and amenable to detailed surveys.

Jan 1, 1950

Bio-Oxidation of Arsenic and Stibium Bearing Gold Ores Bio-oxidation of arsenic and stibium bearing gold ores with acidithiobacillus ferrooxidans was studied. The preoxidation results show that the best bio-oxidation technical parameters are the initial pH in the range of 1.8 ~ 2.0, particle sizes under 0.074 mm, temperature in the range of 25¦C ~ 30¦C and rotating speed of the orbital incubator in 100 rpm ~ 160 rpm. The leaching results show that If the ore, of which contain 10.37 per cent arsenic and 36.81 per cent stibium, is not bio-oxidised, gold leaching is only about 41 per cent, after 8 days oxidised, the result is about 76.55 per cent, which improved about 35.62 points. The relationship between gold leaching and arsenic oxidation is direct proportion, furthermore, it needs only partly oxidise and higher gold leaching could be get, for example, gold leaching is over 90 per cent when asenic oxidation is 60 per cent. The results will provide theoretical and technological supports of bio-oxidation arsenopyrite for pretreating refractory gold ores.

Sep 13, 2010

By M A. Lund, C D. McCullough

In Australia and worldwide, open cut mining has become increasingly common over the last few decades through changes in excavation technology and ore economics. However, such operations frequently leave a legacy of open mine pits once mining ceases. Pit lakes will then form in mine pits that extend below the water table when dewatering operations cease. Pit lake waters are typically contaminated with metals, metalloids, saline or acidic/alkaline and rarely approach natural water body chemistry. Physically, pit lakes have unique bathymetries, are often strongly wind sheltered and have very small catchments. Nevertheless, pit lake waters often constitute a vast resource but of limited beneficial use (due to water quality issues); with a potential to contaminate regional surface and ground water resources. Water in pit lakes has the potential to be useful for a range of purposes in the Australian context of characteristic hot, dry climate and relatively few natural water bodies. Consequently, pit lakes can be seen to represent either a significant liability or a water resource to mining companies and regional communities. However, the lack of knowledge on pit lakes continues to hinder their proper management. This paper summarises the limited information currently available on water quality associated with Australian pit lakes. Information on pit lake occurrence, distribution and water quantity and quality is not nationally collated and requires immediate and ongoing attention from both mining companies and regulating authorities. Lack of a readily available database for pit lake occurrence, distribution and water quality fails to realise the potential for these water resources by both mining companies and Australian communities. Lack of access to pit lake quantity and water quality data may also lead to failure to manage this significant source of mining environmental risk.

Jan 1, 2009

Resonance re-emission from nickel vapour affords a convenient method for isolating the resonance lines at 3415A, 3515A, and 3524A. The vapour is generated by cathodic sputtering and is illuminated by light from a nickel atomic spectral lamp. The resonance lines thus isolated can be usefully employed for absorption measurements on mineral samples where the nickel concentration is too high for measurements with the more sensitive line at 2320A. A spectrophotometer employing a resonance lamp as monochromator possesses several advantages where a great number of determinations are made under routine conditions. The wavelength setting is stable under even the most rigorous conditions and with the provision for automatic setting of full scale deflection the instrument requires virtually no adjustment. The instrument has been used under routine conditions for the determination of nickel (in the range O· 05-2 per cent) in mineral samples.

Jan 1, 1968

By Lavers G

Factors governing the dissolution of nickel and iron in pentlandite and pyrrhotite concentrates from Mt. Windarra were studied for aqueous solutions at normal temperatures and pressures. The effects of dissolved dioxygen, carbon dioxide, hydrogen ions, and chloride ions are described. The direct reaction of aerated water wiili pyrrhotite is much faster than with pentlandite, and reaction rates are proportional to the dissolved dioxygen concentration. In both cases divalent metal sulphates are produced initially. The subsequent oxidation of iron(II) to iron(III) and its oxolation produces acid solutions which rapidly attack both minerals. The presence of carbon dioxide or chloride ion has little effect on these rates.

Jan 1, 1976

By J Addai-Mensah, M Adam, W Skinner, J Begelhole, K Quast

Granulation of iron ore fines into robust granules is critical to successful sintering and blast furnace operations in iron and steelmaking. Iron and steelmakers desire iron ore granules with high strength, uniform size distribution and low fuel consumption to enhance efficient sintering operation. Unlike hematite ore, magnetite concentrates do not granulate easily at low binder dosage to yield coarser granules due to the absence of nucleus particles. This motivates the present study to harness the complementary properties of hematite ore to enhance granulation of magnetite concentrates via blending. The current state-of-the-art in hematite and magnetite blend granulation is reviewed, along with granule property limitations. Preliminary experimental work on granulation of hematite and magnetite blends as a precursor to sintering is reported.CITATION:Adam, M, Addai-Mensah, J, Begelhole, J, Quast, K and Skinner, W, 2017. Enhancing magnetite concentrate granulation by blending with hematite ore, in Proceedings Iron Ore 2017, pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Lead isotope measurements indicate that lead from the A.B.H. Consols mine and two transgressive veins in Browne's shaft is "Thackaringa" type and not "Broken Hill" type.

Jan 1, 1970

In Broken Hill, Northern Rhodesia, two water jacket lead furnaces have been in operation for the past three years. The furnaces were erected in war time, and only absolute essentials were procurable. The water for the jackets was obtained from wells adjacent to the works, in a dolomite formation. There being no water-softening plant, except a small one capable of treating water for the power plant only, this water was found to make a heavy scale in the jacket. During 1917 several jackets were burnt through, resulting in serious trouble and loss of output. In order to avoid this, furnaces were stopped twice a month for 8 hours and scale was removed as far as possible. In addition to the scale trouble during the summer months, a green slime grew in the supply tanks and occasionally became detached from the tank and collected in the cocks near the jackets. This caused risk to the jackets and was difficult to remove without a stoppage of the furnace. In 1918, bundles of wattle bark were placed in the hot well at the rate of one ton per month. These extracted the tannin and added from 0.5 to one part of tannin per 100,000 to the circulating water. The hot water was cooled over a brushwood cooling tower and returned to the supply tanks. The well water required to, make up the wastage was estimated at 40,000 gal per day.

Jan 1, 1920

G. R. Compton (Gold Mines of Kalgoorlie (Australia) Ltd., Fimiston, W. A.) : In congratulating Mr. Hooker upon his resume of Mr Parry's paper I have in mind the fact that he carried out the research into pipe pressures. Hydraulic filling as practised in Kalgoorlie has created world wide interest, with these pressures and percolation being vital points.Early in the 1950s, representatives of the Kolar field were conduGted over the local mines where stopes at depths below 2,000 ft were being filled. The problems of pipe pressures were their main consideration since depths of up to 10,000 ft were envisaged.Mr Krishnaiah and Mr Murthy from the same field are with us today and perhaps we may hear of their experiences with depths of 6,000 ft and long lateral lines.J. Holly (Lake View and Star Ltd., Fimiston, W.A.): There is one phase, which I would like to mention myself, that has been very evident in Kalgoorlie operations. That is, we do not get the percolation properties that are obtained on many other fields in the world, and our tendency here has been to assess the quality of our fill more by its settling rate, i.e. the rate at which we can draw off clear water at the surface of the filling levels, rather than the rate that this water percolates down through the fill before it consolidates.We are tending now to measure the quality of our fill as a settling rate rather than as a percolation rate.Americans talk about percolation rates being the important property: If anyone has any experience on operating with fills with different percolation rates, I think their views would be very interesting to the meeting art this stage. Mr ...

Jan 1, 1965

THE following brief paper is submitted with a view to encouraging the exploitation of hitherto neglected 10w~ grade ore-bodies which are suitable for extraction by open-cut methods.The Corinthian North mine, situated 10 miles from Southern Cross, in the Yilgarn district of Western Australia, furnishes an example of low working costs, although operations are carried out on quite a limited scale.The body of quartz which is now being worked strikes N.W. and S.E., has a very slight underlie to the west, and lies between bodies of quartz-hrematite s,chist on the east and amphibolite on the west.So far as the property has been explored, it would appear that the underlying sulphide rises to within about 70 ft. of the surface in the northern end of the workings, and pitches away to the south at a grade...

Jan 1, 1915