Search Documents

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T Purvis, Z Liu

Ernest Henry mine (EHM) is an underground sublevel caving mine located in north-west Queensland with a production rate of 6.4 Mt/a. The mine has sublevels spaced with a 25 m vertical interval. The production process on each level starts with the drilling and firing of a blind uphole rise to start the slot extraction. These rises are fired as a single shot and routinely need to achieve a design height of 22 m to 30 m depending on the local mine geometry. If the rise fails to perform as designed then the production phase of the level is delayed with significant rework required to remedy the situation.This paper describes the process that the EHM team has followed to improve the first time performance of each rise. The improvement process commenced with a review of results from previous rises and resulted in the identification of a number of improvement opportunities. A revised holistic approach was established for the process, which included involvement from operators and engineers. Through continued measurement and review of rise performance, inputs to the process were improved to a point where reliable results can now be expected. The successful performance of subsequent rises has been verified through a comprehensive quality assurance quality control (QA/QC) program. Before quality control processes were implemented, the success rate of blind uphole rises was only 11 per cent (one out of nine rises) at EHM. In comparison, the success rates have been vastly improved to 25 per cent (one out of four) and 75 per cent (three out of four) respectively following two stages of improvements. This paper concludes with the ‘current’ series of best practices used at EHM and recommendations.CITATION:Purvis, T and Liu, Z, 2017. Improving the performance of blind uphole rises at Ernest Henry Mine – a case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By S C. Dominy

The gravity recoverable gold (GRG) parameter reflects liberated gold or gold-dominated composite particles that can be recovered by gravity separation. Recoveries depend upon mineralogy, in situ particle size and the comminution and extraction method used. Any ore bearing >15 per cent of gold greater than 50 ¦m in size is likely to have a GRG component. The principal characterisation methodology applied is the three-stage GRG (3GRG) test, based on a 40 kg to 100 kg sample. An alternative is the single-stage GRG test (SGRG), which is generally based on a 20 kg sample. Experience has shown that GRG values can vary throughout an orebody, particularly within different grade and/or mineralogical domains. Test programs must consider sample frequency and mass. This study demonstrates the variability of GRG results based on different sample masses. Consecutive underground faces on a coarse-gold dominated quartz vein were sampled taking five different masses from each. Each sample was processed using a SGRG approach. Subsequently, each development round was batched through a small gravity production plant. The results show that the small samples understate the plant GRG and show inter-sample variability. Large samples show less variability and a SGRG closer to the plant GRG. A high SGRG broadly correlates to higher gold grades, more coarse gold and larger gold particles. These results are intuitively correct, but indicate the likely challenges of sampling for gold recovery in heterogeneous systems.CITATION:Dominy, S C, 2013. Variability of gravity recoverable gold values in relation to test sample size, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 293-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By N Clarke, J Hunt, A Barros, L Keeney

The Gramalote orebody is a large low-grade gold deposit situated in the San Roque municipality, 124 km north-east of Medellin in Antioquia, Colombia. It is jointly owned by AngloGold Ashanti (AGA) and B2Gold and is currently in Feasibility Study phase. In 2013 AGA requested CRCORE to undertake a preliminary study of the potential application at Gramalote of pre-concentration by screening, part of the Grade Engineering suite. 160 samples of coarse assay rejects (-3 mm) were tested and showed one of the strongest responses seen worldwide to that time, suggesting that about 70% of the gold could be recovered into 40% of the mass. This was seen as potentially markedly improving the Gramalote economics. A large-scale testing program was implemented on site to follow up these results. A total of 18 samples of 17 t each were mined along a pre-existing exploration adit. A complex test flowsheet allowed size fractions to be generated from the as-received material as well as after crushing to 53, 23 and 3 mm, all from the same head sample. The procedures were designed after carrying out a heterogeneity study to measure sampling errors. The coarser size fractions were designed to study the effect of crushing on upgrade response and predict the response on open-pit run-of-mine ore. The finer size fractions were designed to investigate means of predicting the upgrade response across the orebody. The large-scale testing closely confirmed the average upgrade response as predicted from drill core assay rejects but found that only the -53 mm crushed material accurately predicted the upgrade response of individual samples. Ore geochemistry was able to usefully distinguish samples with good and poor response. A small study on drill core suggested that, for Gramalote, fine crushed material distinguishes vein associated and disseminated values but not other factors that control actual outcomes.

Nov 10, 2020

By I H. Wilson

After decades of turmoil, Rwanda launched its Vision 2020 in 2000 aimed at reconstructing government and addressing poverty. Implementation focused on the agricultural sector, infrastructure and education. Later economic development and poverty reduction strategies recognised that expansion of tantalum, tin and tungsten mining could potentially diversify Rwanda’s economy and improve the balance of trade. In 2005, comprehensive environmental legislation requiring environmental impact assessment for all new mines was introduced. Since 2006, government-operated mines have been privatised and illegal artisanal miners encouraged to form cooperatives. The government passed a new Mining and Quarry Exploitation Law in 2008 and approved a new Mining Policy in 2010. This policy was influenced by the Africa Mining Vision (AMV), which the African Union approved in 2009 to ensure African countries obtain reasonable benefits from exploitation of their mineral wealth. The Rwandan mining industry has grown significantly over the last five years and the second economic development and poverty reduction strategy, released in September 2013 forecasts a further three-fold increase in production in the next five years. The strategy prioritises the mining industry and proposes new legislation, better information, greater transparency, encouragement to investment and use of best environmental and technical practices. It also proposes that Rwanda develop a ‘green’ mining sector featuring a ‘model’ mine that is fully funded through green investment and incorporates renewable energy systems, water treatment systems, forestry schemes and local training. Many international development partners have contributed to the current legislative framework and are monitoring environmental and social performance of mining in Rwanda. Local communities have generally benefited from mining and the new mines show improved environmental performance. The major challenges are dealing with the legacy of past haphazard mining practices and establishing linkages between the mines and local industries to create broader economic development.CITATION:Wilson, I H, 2014. Rwanda and the Africa mining vision, in Proceedings Life-of-Mine 2014 , pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Aspinall T. O, Bell L. C

Increased awareness and stricter enforcement of regulatory requirements for adequate rehabilitation of surface mining sites has made environmental planning an essential part of strip mine planning. Rehabilitation is site specific and should be based on data which relate to that site. Cost-effective spoil pile design to minimise erosion is an important part of rehabilitation. Spoil pile design is an integral part of strip mine design. QCT Resources Limited has provided a postgraduate scholarship toward research in this area. The controlling factors of spoil pile design are post-mining land use, drainage requirements and degree and rate of erosion. The extent to which mine design is controlled by these factors is determined by regulatory requirements. To plan acceptable rehabilitation programs, erosion processes must be accurately modelled, and a range of erosion prediction models are available. Useful prediction models can be placed in two categories with the first category containing soil loss prediction models which can be used to predict the amount of soil lost from an area over a short or long term basis. Models in this category include the Universal Soil Loss Equation (USLE), Water Erosion Prediction Project (WEPP), Griffith University Erosion and Sedimentation System (GUESS) and Chemical, Runoff and Erosion from Agricultural Management Systems (CREAMS). The second category contains topographic evolution models which give an indication of the long term morphological development of a formed surface subjected to erosion processes. Models in this category include "Topog", Willgoose's Physically Based Catchment Evolution Model and Areal Nonpoint Source Watershed Environment Response Simulation (ANSWERS). The USLE has been used in the agricultural field for soil loss prediction. To apply the equation to mine sites in Central Queensland, it is necessary to understand the factors affecting erosion at the sites. This understanding should allow the variables of the equation to be quantified. The rainfall factor applied in the USLE is independent of engineering design or soil management techniques. The factor of spoil erodibility is dependent on the material's physical and chemical properties and can vary from site to site. In the equation, the topographic factor, cover and management factor and conservation practices factor can be varied by design to reduce erosion on rehabilitated areas.

Jan 1, 1991

By P J. Hawke, M F. Flis

The Hamersley Basin of Western Australia holds significant tonnages of detrital iron deposits. Formed by a cyclic weathering and eroding sequence of nominally barren banded iron formation, they may form rich proximal accumulations of iron cemented gravels distal from any obvious hard-rock iron mineralisation. While generally small, they nonetheless represent excellent economic targets as they are near surface and easy to mine. The relatively high density of iron detritals, when compared with their sedimentary hosts, makes the gravity method the primary method of exploring for these blind deposits. Identification of possible trap sites is used as a precursor to gravity surveying, with magnetics used as an ancillary method prior to drilling. Application of the gravity method in this terrain is not straightforward. Detrital trap sites are best developed next to the spectacular cliffs that form the range fronts to the Hamersley Ranges. Precise terrain corrections and use of first vertical derivatives are routinely applied to gravity data in an effort to map every possible gravity high that may reflect the presence of a detrital accumulation. Extensions to Hamersley Iron Pty LimitedÆs BS2D deposit were discovered by the routine application of gravity. This methodology has been used to create a model by which exploration for detrital deposits continue to the present day.

Jan 1, 2002

For the past 3 years Waihi as a community has been actively engaged in consultation about its future with regard to the environmental, cultural, economic and social viability. This has been made possible through the implementation of the Waihi Community Vision (WCV) process which bought together a diverse range of people and interests.   Through their collaboration and collective energies, they produced a montage of possibilities for the future of Waihi, known as the 2020 Vision. A proceeding evaluation process was adopted by the group to enable the myriad of projects to be assessed and prioritised in terms of the communityÆs social, economic, cultural, environmental and spiritual values.   From this came the desire to be involved in the implementation of these ideas and create an organisation that could facilitate the successful manifestation of the 2020 Vision and other suitable projects.   The Vision Waihi Trust (VWT) was formed in February 2006 and is intended to be a tool through which the community can address issues about its future sustainability. They will work collaboratively with community groups, Hauraki District Council and Newmont Waihi Gold to develop and implement innovative and practical solutions. It should be acknowledged that such outcomes are subject to influence by both external and internal factors and it is important to consider this when looking at sustainability issues.   Waihi is now at a very interesting stage of its development and has the opportunity to proactively design and implement plans to determine its future rather than just let things evolve. A town with a strong sense of its roots and with a strong community identity may be a more attractive as a place live and work. There are additional business opportunities which may also be stimulated by a community that takes charge of its own destiny.   The process that has been worked through over the past three years gives a solid foundation on which to build and must be viewed as positive community development. Waihi certainly has a unique proposition to take to the marketplace, based on its rich gold mining heritage and current modern day mining operations. This requires investigation, refinement and implementation and Vision Waihi Trust looks forward to building to a vibrant and prosperous Waihi in the years to come.

Jan 1, 2006

By P Christen

The Ernest Henry Copper gold mine situated in North West Queensland, Australia, is owned and operated by Xstrata Copper. Currently the open pit produces 11 Mtpa of ore. With open pit mining ceasing in mid 2011 development has begun on an underground sublevel cave mine to extend the life of the operation by another 12 years. When completed the open pit will be 530 m deep and 1.5 km in diameter. The orebody dips at approximately 45° and has been outlined a further 450 m below the base of the pit. This provides some challenges for the Ernest Henry underground mine which is designed to initially truck development and production ore from the end of the pit until a hoisting shaft is commissioned in 2013. Production will then increase to 5.0 Mtpa on its way to an ultimate rate of 6.0 Mtpa in 2016.This paper will focus on the capital development and infrastructure requirements for the underground mine. Areas covered include mine accesses, ore handling system, accommodations for the dip of the orebody, primary ventilation design, dewatering systems and selection of an underground workshop over surface only maintenance.Discussions include the complications arising due to the mine being located directly below a large open pit and the combination of first principle cost analysis and risk assessment which has been used to safely optimise the feasibility study designs.

Mar 21, 2011

By D T. Feinstein, M B. Gotkowitz

In Wisconsin, state laws and regulations governing metallic mine permitting stipulate that protection of groundwater quality be assured indefinitely through all phases of the mining project, including development, active mining, reclamation, and long-term closure. By rule, the Wisconsin Department of Natural Resources (WDNR) requires that permit applicants use a numerical model to assist in the assessment of compliance with this requirement for all proposed mine-waste facilities. As a part of the compliance assessment, model calculations are used to predict groundwater solute concentrations through time at designated boundaries for comparison to current groundwater quality standards. In practice, this modelling requirement has involved the application of numerical solute-transport models. Our review of a solute-transport model submitted by the developers of a proposed mine near Crandon, Wisconsin, provides us with an opportunity to assess the usefulness of transport modelling as a permitting requirement. Recent evaluations of solute-transport models by other workers suggest limitations in predictive accuracy. Our review of the model submitted for this project also identified important limitations due primarily to uncertainty in calibration of model parameters at the undeveloped site. The utility of any model to predict project compliance or non-compliance with numerical standards is limited by the range of uncertainty of key model parameters, such as dispersivity and porosity. Uncertainty in the future behaviour of the solute source(s) also reduces the predictive power. Moreover, the site characterisation provided by the model may have limited power to describe the site condition post-development. Although these inherent shortcomings accompany the use of solute transport models at undeveloped sites, the requirement for model development and the ensuing technical review has substantially assisted in our evaluation of site conditions and project design. Through this process we have identified elements of the waste facility design that are crucial to the environmental viability of the project, resulting in modifications to original project proposals. While results from this model review will be used to evaluate compliance, additional benefits come from the identification of critical design features that enhance groundwater protection.

Jan 1, 2003

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

Computation is believed to be a powerful tool in scaling-up chemical processes and in designing materials, however, is being challenged by low predictability and limited scalability. This presentation will discuss the promising future of multi-scale computation in solving these two problems to realise the real-time simulation of industrial processes. Multi-scale structures are a common nature of most chemical systems and the meso-scale phenomena are believed to be the road blocks not only in improving the predictability of physical modeling but also in extending the scalability of computation. Focusing on the meso-scale phenomena, a series of research has been carried out at the Institute of Process Engineering, Chinese Academy of Sciences, for the past three decades. Starting with a simple idea of modeling the meso-scale clusters in gas-solid two phase flows, the so-called EMMS (Energy-Minimisation Multi-Scale) model was established. In verifying the stability condition of the model, the pseudo-particle approach was proposed to explore the micro-mechanisms in particle-fluid systems, and the strategy of the EMMS model was extended to other six different multi-phase systems, resulting in a unified conceptual formulation of multi-phase complex systems expressed by a multi-objective variational problem. In applying this model to different multi-phase systems and to industrial problems, it was recognised that the EMMS model defined a new paradigm of multi-scale computation by realising the structural similarity between software, hardware and the problems to be computed. This paradigm of computation was implemented on a multi-scale supercomputer with a capacity of 1.0 petaflops by integrating CPUs and GPUs (Graphic Processing Units), showing high efficiency and low cost. Running the EMMS model on this computer, the simulation of hydrodynamics of multi-phase systems can be speeded up very much, indicating a promising future of virtual reality of process engineering. The presentation will review this series of work, introduce successful applications in industries, and will be concluded by emphasising the critical importance of the meso-scale phenomena as the bridge between macro-dominants and micro-mechanisms. This is an ABSTRACT ONLY. No full paper was prepared for this presentation.

Sep 13, 2010

Tomago sandbeds is an unconfined coastal aquifer located 20km. north of Newcastle in New South Wales, Australia. These sandbeds extend over an area of about 130km. The average aquifer depth is about 20m. with a mean transmissivity of about 400sq.m/day and a specific yield of about 0.2. The city of Newcastle and surrounding areas derive water from Tomago for potable purposes. The average extraction being about 50 ML/day. The iron value of the ground water varies between 5 and 15mg/1. This iron is removed by a conventional water treatment plant using Alum. The aquifer whilst principally quartzose also contains deposits of heavy minerals like rutile, zircon, ilmenite, etc., The mineral sand mining has been in progress at Tomago since 1972. Mining is carried out in a con- structed pond with a water depth of about 5m. on which is floated a suction cutter dredge that moves across the front of the pond using a water jet to entrain the soil from the ground surface to the bottom of the mineralised zone. Effect of mineral sand mining on ground water quality, particularly iron, was the subject of intensive investigations undertaken at Tomago since 1970. The effect on water quality was studied by collecting and analysing water samples from network of observation wells established during the period of mining. Water samples were collected about 4-5 years prior to mining and analysed for iron, sulphate, chloride, pH, etc., After mining the observation wells were re-established at the same locations and water samples were collected and analysed for at least 5 years after mining. Water samples collected from majority of the observation wells indicate an increase in iron levels. The level of increase is very site specific. The increase in iron is also

Jan 1, 1987

By H Utama, hi, A Suw

PT. Indo Muro Kencana (PT.IMK) is gold and silver mine located in Central Kalimantan province, Indonesia. Mining activities in PT.IMK is conducted in Bantian pit area by applying surface mining method and using combination of excavator and hauler (articulated dump truck and rigid haul truck) as the transportation for ore to the crushing plant and waste material to the waste dump. Current blasting practice is ore-waste blasting. Ore-waste blasting is the term where the ore and waste rock are blasted in the same blasting process. Blasting is conducted by using nonel initiation system. By multiple pits operation, monthly powder factor is varied from 0.23 kg/t to 0.27 kg/t. Emulsion blend with density 1.15 g/cc is used as bulk explosive. At this stage, the concept of geoblast is proposed as an engineering tool for Drill and Blast engineering practice in PT.IMK. In addition, there is a need to maintain rock fragmentation by blasting, to maintain monthly powder factor, and to maintain excavator’s productivity. Next, the concept of scaled depth of burial (Chiappetta and Treleven, 1997) and the concept of blastability index (Lilly, 1986) are proposed as geoblast’s tools to improve blasting practice in PT.IMK. It is expected that rock fragmentation by blasting, explosive consumption and excavator’s productivity will be maintained by integration of geoblast and drill and blast engineering. Furthermore, the objective of this paper is to integrate geoblast and drill and blast engineering in order to create an engineering guideline in PT.IMK. Additionally, blasting trials with air decking application is proposed in order to support the geoblast’s improvement. It is planned that these blasting trials will be conducted in 2022. In conclusion, it can be seen that integration of geoblast and D&B engineering in PT.IMK is relevant to improve current drill and blast current practice and applicable to maintain rock fragmentation by blasting.

Nov 29, 2022

By R Stimpson, B Johnson, B Hesse

During a period of twelve months between FY18-19, a series of trials were conducted to compare production drilling accuracy using two different methodologies, and the subsequent impact this had on stope performance (dilution and recovery). Testing was conducted at a series of underground mines in Australia. The drill rig’s existing alignment processes were compared to a new technology system, with the following observations: • The new technology was proven to limit rig alignment error, thereby reducing average blasthole deviation, resulting in an increase in the number of holes drilled within tolerance by up to 160%. • The increased accuracy reduced stope dilution significantly by reducing over-break of subgrade ore, whilst also increasing drilled meters (faster stope-cycle time), reducing the bridged tonnes ratio, and facilitating the capture of previously uneconomical stopes. A cost-benefit analysis extrapolated from each of the trials showed the extent to which the new technology, when applied to production data, reduced average dilution, increased ore recovery as well as general drill and blast productivity. In one such trial, the new technology was proven to have reduced average dilution by net 45.4%, which if applied to a full year’s production data, would result in AUD8.2M additional ore recovered, with AUD4.5M less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 to AUD106. This improvement was maintained over the following 12 months – reducing average dilution from 22% in FY17 to 12.1% in FY19.

Mar 15, 2021

Martha Mine is an open pit gold-silver mine, located within the township of Waihi, 150km southeast of Auckland and is operated as a joint venture between Normandy Mining Ltd. 67 %) as Manager and Otter Gold Mines Ltd. (33%). The deposit was historically mined, by underground methods from 1888 to 1952, producing 5.5 moz of gold and 30 moz of silver, from 11 mt of ore. The current operation began in 1988, producing, to June 1999 - 867,245 oz of gold and 5.5 moz of silver from 9.5 mt of ore. The licensed reserves were due to be mined out by late 2000. Consents were granted in December 1998 to allow the expansion of the operation through to 2007 accessing an additional 7.5 mt of ore at 3.4 gpt Au and 26.0 gpt Ag for 800,000 oz of gold and 6.4 moz of silver. The key elements of the expansion are: 1. Pit enlargement 2. Upgraded crushing and material handling facilities 3. Construction of a second tailings storage facility 4. Upgraded water treatment capacity 5. Increased operating capacity This paper presents an update of expansion activities to date.

Jan 1, 1999

Production scheduling of open pit mining is a key area as it deals with the management of operating cash flows of mining companies. The efficiency of long-term schedules is usually assessed with economic criteria such as net present value (NPV), discounted cash flow rate of return (DCFROR) and payback period, which are not sufficient on their own for revealing the complex picture of the decision-making process.This paper offers a thorough analysis of the most important contemporary criteria of long-term production scheduling, as way to provide the mining practice with a new approach to the decision-making process. The list of criteria includes technological, economic and probabilistic ones. A detailed case study is provided aiming to illustrate the applicability of the criteria for comparing the scheduling approaches regarding the economic interests of a mineÆs owner and contractor. The results obtained can be used for revealing new trends in the current methodology of open-pit production scheduling optimisations.

Sep 26, 2011

Pongkor Gold Mines is one of seven units of production owned by PT Aneka Tambang (State owned mining company). The mine is located in the western part of Java Island, Indonesia. It is in the Bogor District and approximately 110 kilometres to the south of capital Jakarta. It is located in very steep hilly terrain intersected by many river valleys and the mine site is approximately 500 metres above mean sea level (see Figures 1 and 2 - Mine location map and picture)

Jan 1, 1997

By D Wimpenny

The Bogong Power Development Project in Victoria, Australia involved the construction of a 15 m long mass concrete plug up to 9 m in diameter within the head race tunnel. The plug is critical to theperformance of the scheme as it permanently seals the head race tunnel under approximately 300 m head of water.The location of the plug in the headrace tunnel was determined by a programme of in situ rock stress testing using both hydrofracturing and over coring stress testing methods.In recognition of the importance of the plug, the Head Contract specification requires that its temperature during hydration be controlled using an embedded cooling system. In addition, contact grouting and curtain grouting around the plug cannot commence until thermal contraction was substantially complete.This paper describes the use of bespoke fi nite element software to model the temperature rise in the plug and design mitigation measures to control temperature rise in the plug. These measures include restricting the concrete placing temperature to 10°C, incorporating 39 per cent fly ash in the concrete and installing embedded cooling circuits.Site trials were undertaken to calibrate the model for the proposed concrete mix. The cooling system comprised 25 mm ID pipes forming twelve separate circuits that fed 7°C water from a single chiller unit. The cooling system reduced the peak temperature in the plug to approximately 30°C and the associated risk of early-cracking. The time before contact grouting could commence was shortened to less than two weeks from casting.

Mar 8, 2011

By D Brennan, S Jahanshahi, F Jorgensen

The recycling of metals can be very efficient with careful selection of the material being recycled. The volume and value of recycled ferrous scrap has lead to the development of steel mini-mills which in turn has caused major changes to the steel industry. Although much smaller in volume, the recycling of lead is very significant, with battery recycling accounting for 60 per cent of annual world production. This high recycle rate can be attributed to the relatively uniform feed-stock from lead-acid batteries. The recycling rates of other metals are considerably lower due to longer use and non-uniform product usage that results in less efficient segregation and processing. It is clear that recycling of metals has advantages but its sustainability is uncertain. What are the key benefits of metal recycling? Metal recycling has technical, economic and social impacts. It is relatively easy to assess recycling on a technical basis, but the social impacts are harder to evaluate. This paper examines some of the issues in evaluating the sustainability of metal recycling.

Jan 1, 2002