Search Documents

By Paul Morrison

The paper describes the design process, trial testing and contract pile installation of 772 pre­cast concrete piles at a site in Surrey, South East England. Recommendations on how to improve the design, construction trials and main contract piling phases of the project are made. The building layout is shown in Figure 1 and is comprised of a central circulation area with five office wings radiating out from its southern side (only three of these wings were constructed in Phase 1 of the project). Approximately 60% of the circulation area and one office wing were built with a single level basement. The basement was constructed "bottom-up" in open cut with the void between the basement walls and the cut slope being back-filled with compacted site won soil above a perimeter drainage system at basement slab level. The building has up to 3 stories above basement level and is a reinforced concrete structure. The client for the project is Pfizer Ltd. Pfizer Ltd was represented on site by Laing Project Management (Laing). The consulting engineer was Ove Arup and Partners (Arup) while the piling contractor was Roger Bullivant Ltd (RBL).

Jan 1, 2000

By L. van Dyk

The project was aimed at evaluating the double-header trains implemented at Great Noligwa mine, looking at the changes from the old conventional trains to the new trains, and identifying possible improvements to obtain an even better and more productive tramming system. The methods used to evaluate the double-header trains at the mine included personal observations, time studies, personal interviews, technical research, safety analysis, cost analysis, production analysis, breakdown analysis, break test analysis, comparisons and working closely with engineering department and manufacturers. Issues that were evaluated are the improvements in safety, cost reductions, tramming congestion reductions, better efficiencies, labour optimization, enhanced driver safety and maintenance. Shortcomings of the double-header trains were identified and recommendations made to improve on the shortcomings. Findings of the evaluation study indicated the following: ?Drastic improvement on safety ?Extreme cost reductions ?Reduction in tramming congestions and bottlenecks ?Better tramming efficiencies ?Optimized labour placement ?Enhanced driver safety ?More effective maintenance. Although there is room for improvements, the double-header trains were implemented with great success at Great Noligwa mine. It is currently the preferred tramming methodology at Great Noligwa mine, and is also implemented at other Anglo Gold Ashanti?South Africa shafts. This tramming system has huge potential for growth, not only in Anglo Gold Ashanti, but in all other older mines that experience major tramming problems.

Jan 1, 2008

By Gordon B. French, Donald E. Garrett

INTRODUCTION Crude oil reserves in the United States are still very large, even though for many years they have not been sufficient to supply our entire domestic requirements. They are continuously being depleted as oil is pumped from the ground, but new discoveries and improved secondary and tertiary recovery methods are helping to reduce the rate of depletion. It is thus a slowly diminishing resource, but even as it is being consumed, immense reserves of oil are left behind as the so called "un-recoverable" portion of petroleum formations. Most oil fields can only obtain a 15 to 40% recovery of the original reservoir, and it is widely quoted that there are still about 300 billion barrels of this un-recoverable oil still in place (Mauch, 1980, etc.). With the present comparatively high oil prices, and the possibility of even higher future prices and short supply, this oil becomes an interesting potential reserve. Mining the petroleum formation would be one means of recovering at least a portion of this oil. The concept of oil mining is neither new nor limited to conventional oil fields, since the procedure could be equally employed with the otherwise difficult to produce heavy oil deposits, and the solid or semi-solid tar sands and diatomaceous hydrocarbon formations. Estimates place the U.S. tar sand resource at about 30 billion barrels, and heavy oil at 5-10 billion barrels (Unitar, 1982). Figure 1 graphically summarizes the heavy oil reserves based upon formation depth and characteristics, while Figure 2 shows their location. It is apparent that the preponderance of reserves are in California and Texas, but that they also occur in many other states. The major companies engaged in oil recovery from the heavy

Jan 1, 1983

In preparing this paper, the writer hopes to achieve two main objects. Firstly, an indication of the desirable features of coke from the viewpoint of a blast furnace operator should be of assistance and value to those connected with coal and coke research, coal mining, the manufacture of coke and the production of iron. Secondly, it is hoped that the conclusions and opinions expressed herein, which are known to be of a controversial nature, will promote some discussion and thought. In this way, other workers may see fit to contribute and enlarge our general knowledge of Australian coke and its behaviour in blast furnaces.Those properties of coke that are considered to be of importance to blast furnace operation will be examined. Although broadly speaking, the composition and characteristics of coke are inherent in the coals used, any special features of coal preparation and carbonization that affect the resultant coke will be discussed. An attempt will also be made to indicate the effect on blast furnace operation of significant irregularities in these properties.THE FUNCTION OF COKE IN A BLAST FURNACECoke has four important functions in a blast furnace:1. To reduce the oxides of iron and other elements to metal and to provide the carbon absorbed by the iron.2. To supply the necessary heat for the process.3. To provide an open supporting structure in which the descending ore and limestone lie exposed to the action of the ascending gas.4. To provide voidage in the bottom of the furnace, so that iron and slag can accumulate in the hearth.

Jan 1, 1957

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

Wetting Characteristics of Mineral Surfaces - Contact Angle Measurements through Molecular Dynamics Simulations

Sep 13, 2010

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By R. Ordóñez Olivares

This manuscript focuses on the design and development of steels for the railroad industry and methods of testing them. Here are summarized the results of research focusing on alloy development and design, with particular focus on advanced rails and wheels. The high-performance steels are characterized for their mechanical and service characteristics. The relationship between properties and cleanliness is discussed and compared to the regular railroad steel. Some of the tests presented are standard tests that are complemented with the nonstandard test recommended by the Association of American Railroads (AAR) and recommended modifications of this. The paper presents the results of metallurgical analysis, mechanical, and residual stress tests. The laboratory methods include microstructure, residual stresses, tensile, hardness, fracture toughness, and microcleanliness tests.

Jan 1, 2013

By E. S. Shedd

Amenability studies were conducted by the Federal Bureau of Mines on an electrooxidation technique for the extraction of mercury from cinnabar ores, particularly those that are too low in grade to be furnaced or retorted economically. Oxidation was accomplished by electrolysis of the ore while slurried with brine. Mercury was dissolved through the formation of the soluble tetrachloro mercury complex, HgC142-. Mercury extractions ranged from 90 to 98 percent in 4 to 6 hours of processing time when tests were made on eight different types of cinnabar ores containing from 0.7 to 18 pounds mercury per ton ore. Salt concentration was varied from 4 to 10 weight-percent depending on whether Pb02 anodes and iron cathodes were used or whether graphite was used for both electrodes. Power consumption ranged from 17 to 64 kilowatt-hours per ton of ore treated. Ninety-nine percent of the mercury was recovered from pregnant solutions by precipitation on an active metal such as zinc, followed by distillation of the resulting amalgam at 600° C.

Jan 1, 1975

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

Principal component analysis of the variation of Cu, Ni, Zn, Pb, Mn, and Cr in a control group of 96 samples of surface ironstone from the Yilgarn Block, Western Australia, was used to derive a simple graphical method, based on only Cu, Ni, and Cr, for discriminating between massive nickel gossans and other ironstones.When the graph was tested by plotting 400 control samples, it failed to correctly classify only nine out of 176 gossans and 11 out of 224 other ironstones.

Jan 1, 1974

The AusIMM/AMIC code for reporting Reserves seeks to improve the calibre of professional reporting on this subject. But have they gone far enough? Should the code appreciate that the degree of reliability of estimates required will vary with the type of mining planned? How does one "confirm continuity" as required by the code? The aim of optimum development drilling is to achieve appropriate ore zone definition for acceptable estimates of reserves and their economic extraction. Can this procedure be in conflict with the code? How does it affect finance decisions?

Jan 1, 1989