Search Documents

By J. Yianatos, P. Vallejos

In the last decades, the exponential increase in the cells’ volume resulted in significant advantages such as investment costs, footprint and energy savings. However, in larger size cells, despite the increased diameter/height ratio, new constraints arose related to the need for decreasing the larger froth transport distances to enhance the froth recovery. Thus, the use of froth crowders and internal launders became compulsory to maintain the froth transport distances but decreasing the ratio between gas and collected mineral flowrates. Consequently, the bubble load will increase until reaching a critical bubble surface coverage. In this paper, the concentrate carrying capacity (tph/m2) is described in terms of the bubble surface coverage (bubble loading) at the pulp-froth interface and the froth recovery (froth transport) and is evaluated as a function of the cells’ volume and operating variables. A sensitivity analysis, based on industrial operating and design conditions, such as superficial gas rate, particles size, froth crosssectional area and cells’ volume, was developed for evaluating the metallurgical performance of cells from 100 to 630 m3. Results show that limiting carrying capacity can arise for the whole range of cells’ volume, depending on critical operating conditions, particularly in first rougher cells and cleaning stages of industrial flotation circuits. The increase in cells’ volume consistently increases the bubble loading (bubble surface coverage) under all conditions, approaching the limiting conditions more rapidly in the case of cells without internal launders. Otherwise, the limiting condition was achieved when the particle size DPS decreased from 50 to 20 (μm) and for superficial gas rates significantly less or larger than 1 (cm/s). The use of internal launders allows for increasing the range of the operating conditions needed to reach a certain carrying capacity. Keywords: Bubble carrying capacity, flotation cells, bubble surface coverage, cells’ volume

Jan 1, 2020

By T. Song, X. Wang, X. O. Xia, X. J. Luo, B. Chen

Interparticle breakage is the main crushing mode of an inertia cone crusher according to its working principle and feeding condition. In this paper the breakage behaviour of an inertia cone crusher is investigated, based on energy controlled compression combined with the vibration theory, rather than geometry controlled compression (form conditioned) which plays a major role in conventional eccentric cone crushers. The effect of feeding and operating conditions on breakage behaviour was described quantitatively from the perspective of energy consumption and product size distribution. The influence of feeding conditions, discharge size settings and vibration exciter speeds on the crushing process and product quality has been studied according to the results of laboratory crushing experiments. The results of the experiments show that the particle size of broken products becomes finer with the decrease of a discharge gap within the gap range selected by the experiment. The product size increases significantly when the gap approaches the upper limit of 6 mm. The variation of eccentric speed has a more prominent effect on reducing the product size compared with the change of discharge gap. The change in product size is not apparent when the eccentric speed rises to a certain level. The throughput of an inertia cone crusher is sensitive to the change of discharge gap, which increases linearly with the discharge gap and decreases with the eccentric speed. The change of feeding conditions has little influence on the crusher throughput. Keywords: Inertia cone crusher, interparticle breakage, energy consumption, product size distribution

Jan 1, 2020

By H. Lieberwirth, M. Klichowicz

The comminution at grain size level for the liberation of valuable minerals usually requires the highest size-specific energy. Therefore, the full understanding of the comminution process at this level is essential. Models based on the Discrete Element Method (DEM) could be a helpful tool for this purpose. In those, the mineral microstructure, which has a dominant influence on the fracture behaviour, can be described in great detail. One major concern, however, is the missing representativeness of simulated models. In this study, a method to overcome this limitation is presented. The authors show how a realistic microstructure can be implemented into a particle bed comminution simulation using a two-dimensional Bonded Particle Model (BPM). The improved algorithm based modelling approach is exemplarily compared to an equivalent real experiment. Thereby, the focus is set on the analysis of the interfacial breakage and the capability of the simulation to reproduce the experimental results. The comparison of the results shows that simulations at grain size level allow a more detailed evaluation of the fracturing behaviour. This is of special interest as the aim of comminution in mineral processing is not only the size reduction of coarse particles, but an efficient liberation of the valuable components. Hence, simulations with automatically generated real mineral microstructures will help to further improve the efficiency of ore processing. Keywords: Discrete Element Method, grain modelling, particle bed comminution, realistic synthetic

Jan 1, 2020

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. Dehghani Ahmadabadi

High Pressure Grinding Rolls (HPGR) are mostly used prior to pelletising processes to increase the specific surface area (SSA) of iron ore concentrate. For expressing SSA, the Blaine index is utilised as one of the most important dimensional properties of iron ore pellet feed. ISO 21283 is a standard test method that explains the manual of Blaine air-permeability apparatus for determination of this parameter. In this standard, the disaggregation method is based on passing the minus of 1 mm samples from the 0.150 mm sieve. The disaggregation process has an effective role on the results of Blaine airpermeability test especially for regrinding HPGR products. In this research, firstly the Blaine index of samples was measured without disaggregation. Following this, disaggregation was done by passing the minus of 1 mm samples through three sieves with different dimensions, 0.150, 0.090 and 0.045 mm, separately, and the Blaine index was calculated for each one. Finally, lab-mill with rubber balls, called Jar mill, was investigated as another option. Screen analysis and image analysis with SEM were performed to evaluate the effects of the sample's disaggregation on the size distribution and agglomeration of samples. The results showed that the disaggregation method with sieve size 0.150 mm, according to ISO 21283, was not applicable for HPGR products because the particles were still stuck together. In addition, the disaggregation method with the sieve size 0.045 mm or with Jar mill offered reasonable results. Keywords: Disaggregation, Blaine index, specific surface area, regrinding HPGR, ISO 21283, Jar mill

Jan 1, 2020

By M. Rudolph, E. Schach

Tecflote is a new group of nitrile-based collectors for sulfide flotation. Water insolubility results in some interesting implications for the actual mechanism. It is not yet understood if Tecflote is directly adsorbed on the mineral surface as emulsion droplets or if it is only active at the air-water interface, affecting the interfacial rheology or electrostatic- and Van der Waals interactions, which have a direct impact on the bubble-particle contact. Different investigations including contact angle measurements, AFM studies and micro-flotation experiments are conducted to obtain a better understanding of the actual mechanism of Tecflote. Due to the reagent’s insoluble character, the Langmuir-Blodgett technique is used to investigate its behaviour in the air-water interface and to deposit defined layers of Tecflote on mineral substrates for the above-mentioned studies. An interferometric set up is used to investigate the influence of Tecflote on the film thinning between an air bubble and a mineral substrate. In addition, possible synergistic effects for the combination of Tecflote and conventional frothers (e.g. MIBC) are studied. Keywords: Sulfide flotation, insoluble collector

Jan 1, 2020

By L. Rojas Mendoza, F. J. Hrach, A. Gupta, K. P. Flynn

ST Equipment & Technology (STET)’s tribo-electrostatic belt separator technology allows for the beneficiation of fine mineral powders by means of an entirely water-free technology with high throughput and low energy consumption. The STET separator is suited for separation of very fine (<1 μm) to moderately coarse (500 μm) particles, in contrast to other electrostatic processes that are typically limited to particles >75 μm in size. STET has performed exploratory studies with several iron ores including tailings and experimental results to date have demonstrated that low-grade iron fines can be upgraded by means of STET tribo-electrostatic separator to commercial grades (58-65%Fe). Experimental results together with high-level economic evaluations indicate that scavenging processes involving low drying costs, DSO operations and tailings beneficiation offer a commercially viable processing method to recover fine iron that would otherwise be lost by traditional processing. Dry electrostatic processing of iron ore presents a clean, low-energy opportunity for iron producers to reduce costs and wet tailings generation associated with traditional gravimetric, flotation and wet magnetic separation circuits. Moreover, STET technology allows for mining waste utilisation and resource recovery from iron ore fines and tailings, therefore offering processors a novel method to recover fines that would otherwise be difficult to process to sellable grades with existing technologies. Keywords: Iron fines, industrial minerals, dry separation, calcium carbonate, talc, barite, quartz, tribo-electrostatic charging, belt separator, fly ash

Jan 1, 2020

By Huanhuan SU, Jianqiang Zhang, Zhongyuan Liu, Junwei Ma

The high-sulfur bauxite in Henan Province was used as raw material. The grinding fineness, pH value and collector dosage on its desulfurization performance, and industrial flotation desulfurization process were studied. The best flotation desulfurization conditions were grinding fineness of 75%, pH of 8.5, and collector of 600 g/t. “One coarse, one cleaning and one sweep” closed-circuit flotation was established as the industrial flotation desulfurization process. After the closed circuit test, the sulfur content of aluminum concentrate with the yield of 93% was 0.23%, and the sulfur removal rate was 83.16%, and the sulfur content of tailings (sulfur concentrate) was 15.09%. Keywords：High-sulfur bauxite under coal mines, flotation, desulfurization

Jan 1, 2020

By A. J. H. Newell, K. Doherty

A copper-gold project has required a number of trade-off studies underpinned by test work to settle on pragmatic flowsheets and throughputs to support a pre-feasibility study that provides a compelling financial case. The primary trade-off studies were based on the mine schedule, ore type feed-grade recovery relationships, likely concentrate grades and typical marketing terms as well as the estimated capital and operating costs for a range of throughputs and mining strategies. Secondary trade-off studies were conducted for specific circuits and additional processing options. Although the details of these studies are not presented, the technical options and subsequent flowsheets are discussed. While the flowsheets will be optimised during the feasibility study stage, the basis is now fixed for the four ore types that would be mined from the copper-gold orebody. The ore types, resulting from a strong weathering profile, exhibit a wide range of copper mineralisation and gold associations, as well as gangue types. They display a range of characteristics that necessitated a nuanced approach to flowsheet development. The primary separation techniques that have been employed include gravity, classification, flotation and leaching while a range of comminution methods have been selected to suit the properties of the ore types. While technical issues are important factors in terms of maximising the quality of separations, recoveries and revenues, attention to material handling, equipment characteristics, the mine schedule, and capital and operating costs are equally important considerations for settling upon a suitable and robust flowsheet. Keywords: Flowsheet, testwork, studies, saprolite gold, native copper, chalcocite, chalcopyrite

Jan 1, 2020

By P. K. Jain

A spiral concentrator is a density separation device used for the beneficiation of coal and various minerals such as iron ore, chromite ore, gold, beach sand minerals etc. The flow pattern developed in the equipment is complex and unique, yet the operation is very simple, with low capital and operating expenditure. Spirals are applied for beneficiation of material in the size range finer than 2 mm and are capable of recovering heavy minerals as fine as .01 mm. The understanding of the unique flow pattern has kept researchers engaged over the last few decades and attempts are being made to explain such flow patterns so that they can be controlled and modified to improve the operating efficiency, Ep (Ecart Probable Error, also known as probable error in separation) and acceptability of spiral concentrators for processing of fines and slimes - currently being discarded and dumped in the tailing ponds. An attempt has been made in this paper to explain the generation of complex flow patterns with application to classical solid mechanics in the fluid and slurry system. The same has been used to explain the selective separation of particles in different zones in a cross-section on the spiral trough. The paper also discusses the application of a force balance model to explain the generation of secondary circulation. Due to the presence of laminar and turbulent flow regimes in the spiral concentrator, varieties of equations have been proposed in the literature, consisting of different equations for different zones. An attempt has been made to present a unified flow equation for calculation of flow velocity at different positions on the spiral trough. Keywords: Secondary circulation, spiral concentrator, density separation, fine particle processing

Jan 1, 2020

By Y. Cao, C. Li, A. Song

Bubble size plays a key role in determining flotation efficiency. Bubbles can be formed by passing air through pores. Bubble detachment from a pore is driven by lifting forces including buoyancy force and momentum force. Enhancing the momentum force is the key to accelerate bubble detachment and to minimise bubble size. Recent studies show that replacing steady air with oscillatory air supply could significantly decrease bubble size by enhancing the momentum force. To date, the underlying mechanism for the improved momentum force with oscillatory air supply is not yet clear. This work, for the first time, developed a qualitative model for the momentum force as a function of frequency, on/off time ratio and gas flow rate. It was found that the momentum force was positively correlated with the frequency as well as the air flow rate, and was negatively related to the on/off time ratio. The relation between bubble size and these operating parameters was also investigated. Keywords: Flotation, bubble size, momentum force, modelling, oscillatory air supply

Jan 1, 2020

By G. Akdogan, C. Dorfling, L. Bumhira

Hydrometallurgical recovery of rare earth elements from phosphors obtained from end-of-life fluorescent lamps involve leaching followed by extraction of dissolved metals from solution. The similar properties of rare earth elements make selective recovery of individual elements challenging. The aim of the paper was to investigate the extraction of primarily Ce and Tb from a hydrochloric acid leach solution also containing other REEs (Y and Eu) as well as impurity metals (Ca and Al). Batch solvent extraction tests were performed with di-(2-ethylhexyl) phosphoric acid (DEHPA) at various extractant concentrations, pH conditions and organic-to-aqueous ratios. Extraction isotherms and separation factors for the range of conditions tested in the project are presented in the paper. Separation of individual REEs was not possible at the conditions investigated, but a mixed REE product can be obtained in a single extraction stage operated at a pH of 0.5 using 1 M extractant at an O/A ratio of 1; these conditions resulted in complete Y and Eu, 95 % Ce and 99 % Tb extraction with Ca and Al coextraction below 7 %. A better quality mixed REE product can be produced by operating at lower pH and extractant concentration conditions, but this would require a larger number of extraction stages. Keywords: Cerium, fluorescent lamps, phosphors, rare earth elements, solvent extraction, terbium

Jan 1, 2020

By L. Cheng, Y. Liu, Z. Shen, H. Shang, Y. Li

The pre-concentration process of magnetic coarse particles can discharge waste rock or liberated gangue before milling, which is an effective means to reduce cost and increase the efficiency of the concentrator, but the weakly magnetic ore doesn’t have the effective separation method of coarse particle such as hematite, limonite, ilmenite and so on, Because the composite iron minerals contain both strong and weak magnetic elements, the pre-concentration process cannot be applied, or the existing pre-concentration process has problems of complicated configuration and high operation cost. By researching a new type of external magnetic separation technology, the pre-concentration process of composite iron ore was realised by single equipment, which can have a good recovery rate with simple arrangement. In this paper, the separation principle and structure characteristics of the external magnetic separator were researched, and the magnetic circuit characteristics of the external magnet were analysed. The laboratory tests of vanadium titanium magnetite were conducted, and the test results proved that the external magnetic separator can be applied for the pre-concentration process. The industrial application shows that a product of TFe 24.76% with 90.08% recovery, TiO2 10.10% with 91.78% recovery can be achieved from the feed of TFe 20.67%, TiO2 8.33%. Keywords: Coarse particle pre-concentration, composite iron ore, external magnet, magnetic separator

Jan 1, 2020

By C. Karageorgos, J. Sakala, A. Prinsloo, B. Ngambi

The sulphide flotation circuit at First Quantum Minerals’ Kansanshi mine in Zambia produced over 100,000 t of copper in 2019. For this circuit, mineralogical analysis has shown that the majority of the copper lost is hosted in fine liberated chalcopyrite, which is a paramagnetic mineral. The objective of this work was therefore to improve fine chalcopyrite recovery in the sulphide flotation circuit at Kansanshi, using a magnetic conditioning technology to agglomerate fine paramagnetic minerals. This theoretically increases the probability of attachment during collision and therefore improves recovery. A four-month paired ‘t’ test plant trial was carried out and comprised of consecutive ON-OFF periods with and without magnetic conditioning in the rougher flotation bank of the sulphide circuit. The experimental design involved assessment of recovery by size based on daily and weekly composite samples of feed and tails, sized using both wet-screening and cyclosizer. Both the daily plant data and the sized samples showed an increase in Cu recovery with magnetic conditioning ON. A 0.56% copper recovery improvement was measured with magnetic conditioning at a 99.4% confidence level. Keywords: Flotation, fine mineral, chalcopyrite, magnetic aggregation

Jan 1, 2020

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

By J. J. Cilliers, J-A. Lamamy, J. N. Rasera, K. Hadler

Production of oxygen on the moon can be achieved by reduction of lunar soil. One such reduction technology, hydrogen reduction, favours a high proportion of ilmenite in the feedstock. Ilmenite is present in lunar soil as a minor mineral phase, but it can be upgraded using electrostatic separation. This study presents the results of a preliminary investigation into the operating parameters and sensitivities of a free-fall electrostatic mineral separator for lunar applications. Samples of ballotini and ilmenite as well as simple binary mixtures of the two were tribocharged on copper and passed through a uniform electrostatic field. The field is varied to change the electrostatic force acting on the particles. The proportion of material reporting to the positive electrode collectors, negative electrode collectors or the central collector was measured to determine the separation performance. The data confirmed that the charge transferred from the tribocharger to each species is in agreement with the triboelectric series; ballotini was found to charge positively on copper and ilmenite negatively. Particle-particle contacts were dominant, however, resulting in a somewhat symmetrical particle distribution in the collectors. These findings indicate that the copper tribocharger design requires optimisation in order to substantially increase particle-wall contacts. Four binary mixtures with feed grades of ilmenite ranging from 5% to 20% were prepared and tested. This study found that a higher ilmenite head grade resulted in a higher concentrate grade (26.3% from a head grade of 20%) with low recovery (3.4%). In contrast, the lower feed grade resulted in a low concentrate grade but higher recovery. The mass yield of ilmenite was 1.4 times greater for the highest-grade feed than for the lowest. A subsequent study into the reprocessing of middling fraction found a nearly constant relationship between cumulative grade and recovery. This is the first investigation into the effect of feed grade on the concentrate grade and recovery for lunar mineral processing. Keywords: Lunar resources, beneficiation, electrostatic, SRU, ISRU

Jan 1, 2020

By G. Bueno, L. M. Tavares, T. M. Campos

Iron ore pellet feed pressing has been one of the first and most successful applications of High- Pressure Grinding Rolls (HPGR) in the minerals industry. Vale S.A. has been one of the pioneers in this application, currently with six HPGRs in operation in the pelletising plants of the Complexo de Tubarão (Brazil). In spite of the important advances in the technology, risks still exist when scaling-up the process from small-scale information. The present work takes advantage of the recent advances in the mathematical modelling of the HPGR performance, using the population balance model to evaluate the modified Torres and Casali model prediction in iron ore pellet feed pressing for different scales of operation. Results are presented that compare the HPGR performance in different operational scales for iron ore pellet feed pressing, demonstrating the confidence of this model-based approach for scale-up to full-scale HPGRs used in pressing iron ore concentrates. Keywords: Scale-up, HPGR, pellet feed, modelling, simulation

Jan 1, 2020

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By G. Akdogan, S. M. Bradshaw, M. I. Isaacs, P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached in order to remove base metals from a concentrate containing platinum group metals (PGMs). This paper investigates the atmospheric leaching process, in order to develop a better understanding of the leaching behaviour of the base metals; in particular Cu, Fe, Ni, and the PGMs in particular Ru and Ir with key process variables, acid concentration, copper concentration under oxidative leaching conditions. Higher initial acid concentration resulted in a higher copper, iron and nickel extractions, as well as higher leaching rates together with faster Cu, Ru, Ir precipitation occurring. On the other hand, a higher initial copper concentration resulted in more nickel but less iron being extracted. Keywords: PGM, converter matte, leaching, precipitation

Jan 1, 2020

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020