Search Documents

By Marcus Daubner

This paper explains how BAUER Spezialtiefbau GmbH uses digital methods on projects - starting from work preparation to completion of works. More precisely, the advantages of BIM-based planning during work preparation and the automated and structured data management - both machine production data and the manually recorded quality-relevant reports - during execution phase are displayed. In this context, the benefit of the digital twin to optimize processes, to reduce defect costs, for a more effective reporting sys-tem, and the further usage of as-built information in the BIM or GIS process is described.

Sep 1, 2022

By Suresh Chikati, Gangadharan Santhanam

Twin tunnels were constructed to a length of 863m using TBM in one of the underground metro projects. The tunnels pass through complex geological conditions (soil, rock and mixed conditions). This paper presents the consideration of volume loss and the corresponding ground settlement associated with the excavation of twin TBM tunnels by analytical and numerical methods. Empirical methods were used to calculate the ground settlement induced by the excavation of twin tunnels. The ground settlement values were directly derived from the two parameters: the volume loss and trough width parameter. These parameters are calculated based on the geological conditions at the tunnel face and tunnel overburden. The finite element software, Plaxis 2D was used to model the soil parameters with appropriate geological conditions. Twin tunnel excavation is simulated in Plaxis 2D and the effect of tunnelling on the ground was simulated by percentage volume loss. The suitable line contraction value was applied to the tunnel linings to simulate the volume loss. The surface ground settlement was directly obtained from Plaxis 2D. Instrumentation arrays were proposed along the twin tunnel alignment, to provide the ground settlement monitoring data within the influence zone of tunnelling activities. The derived ground settlement values from analytical and numerical methods were compared with the actual field instrumentation and monitoring data. From the field instrumentation data, the actual volume loss values were calculated. The compatibility of ground settlement and volume loss calculated using analytical and numerical methods and those measured using field instrumentation data is discussed in this paper.

Sep 1, 2022

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By Zibo An, Yong Hu, Hao Zhang, Hong Cao, Jun Xue, Zhen Luo

Phosphogypsum (PG) is a by-product of solid waste produced by the phosphate chemical industry. Owing to large emissions and massive storage issues, it causes a potential threat to our environment. Hereby, a method based on the precipitation and crystallization properties of calcium phosphate-magnesium ammonium phosphate (CP-MAP) followed by its adsorption on active solid waste powder is used as the main principle to treat PG harmlessly. The treatment process and its influencing factors for orthogonal experiments along with the associated environmental safety have been studied in detail. The results showed that this method could simultaneously remove soluble phosphorus and soluble fluorine from PG. When ACP, FA, HBM, and Ur were added to PG at a dosage of 3%, 13.5%, 0.04%, and 0.04%, respectively, the residual phosphate and fluoride contents was 0.061 mg/L and 0.856 mg/L respectively in the PG leaching solution. Compared to state-of-the-art approaches, this method exhibited higher efficiency in removing phosphate and fluoride. Most importantly, this method does not cause any secondary pollution in the process, thereby showing a novel application in large-scale industrial treatment.

Aug 29, 2022

By Mamookho Elizabeth Makhatha, Mbal Henock‑Michel Mwanat, Kubangala Brest Kasongo, Ntumba Edward Malenga

This study investigated the operating parameters that affect the kinetic dissolution of copper and cobalt from sulfidic ores. The sulfuric acid concentration, temperature, sodium chloride concentration, particle size range, and leaching time were selected to deduce the kinetic mechanism of the leaching reaction. Other parameters, such as a stirring speed of 250 rpm and the percentage solid 10% w/v, remained constant. The results reveal that an increase in acid concentration enhances the leaching rate of copper and cobalt. Copper and cobalt dissolution was positively affected by the addition of sodium chloride. The highest leaching rates of copper and cobalt were 24.71% and 15.65%, respectively. The chemical control and diffusion control by shrinking core models are well fitted as the kinetic models representing the dissolution of the minerals. The respective activation energies for copper and cobalt dissolution of 10.92 and 31.023 kJ mol− 1 for the chemical control and 18.83 and 37.28 kJ mol− 1 for diffusion reaction control were established from temperature-based experiments.

Aug 26, 2022

By R W. Shaw

The MTM Process targets treating lower grade and/or problem concentrates that are not attractive to smelters. The process has been developed at laboratory scale for copper and is based on a related development for zinc that has been extensively developed both in the laboratory and through pilot testing. The basis of the process is novel ammonia-ammonium chloride leach chemistry adapted to give high copper extraction whilst being selective over iron, arsenic and many other elements. The preferred flow sheet depends on location, especially infrastructure and utilities. These impact upon the leach and crystallisation stages more than copper reduction.

Aug 24, 2022

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

By R W. Henley, L Knuefing, M Turner, Y Zhang, M Saadatfar, A Limaye, R Cruikshank, M A. Knackstedt, A Kingston, L Beeching, N Francois

A better understanding of ore fragmentation and the textural features of ore is a key to the energy efficient extraction of targeted minerals from low-grade ore deposits. In this study, X-ray microcomputed tomography (micro-CT) is employed to study mineral liberation during the tensile failure and onset of fragmentation of a copper ore. Our results show that X-ray micro-CT could inform new studies of ore micromechanics and fragmentation at the laboratory scale and may offer new avenues to address current challenges in the design of efficient comminution processes. We present the results of experiments based on a high-pressure apparatus enabling micromechanical studies to be carried out in situ (inside a micro-CT scanner). This platform produces high-quality 3D images of the evolution of a sample of porphyry copper ore during an in situ fragmentation test. A sequence of tomographic images enables mapping in 3D of both the deformation of mineral phases and the fragmentation process. The fragmentation occurs quasistatically through multiple stages starting with an initial tensile fracture splitting the ore diametrically, followed by tensile-activated nucleation and growth of multiple fractures producing a complex fracture network. Coupling breakage with microstructural information enables quantitative determination of the impact of ore texture heterogeneity on fracture patterns and mineral liberation. This microstructural information can be compared to key measurements of the ore mechanical behaviour such as the global deformation energy, strain deformation field and the stress relaxation response. The latter allows one to identify interesting precursor signals of the tensile failure. The copper liberation, fragment size distribution and breakage patterns are statistically characterised and related to comminution mechanisms which are clearly identified in the sequence of tomographic images. The two dominant mechanisms are rock-rock friction/compression induced by fracture closing and compression-driven fragmentation at rock-crusher contact points.

Aug 24, 2022

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By M Saghaeian, M Zare, V Sheikhzadeh, R Hejazi

High-Pressure Grinding Roll (HPGR) is one of the efficient methods for increasing the specific surface area (SSA) of iron ore concentrate for pellet feed production. HPGR grinding mechanism implies that material should compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study, by doing SSA increasing tests with pilot HPGR, the effects of silica reduction on SSA increasing results were investigated. For this purpose, HPGR tests were performed on an Iranian magnetite concentrate before and after reverse flotation silica reduction tests. Based on the laboratory test results, silicates have been concentrated in two fraction sizes of the sample comprises coarser than 150 microns in form of quartz and finer than 7 microns in form of iron silicates. These silicates have been effected on reduction of concentrate bed pressure resistance by creating a pasty and sticky mud. In this condition, HPGR cannot work properly and operation results are not acceptable. According to flotation silica reduction tests, with 90 per cent weight recovery, concentrate Fe grade is increased from 67.8 per cent to 69.5 per cent and SiO2 content is reduced from 1.98 per cent to 0.9 per cent and especially for lower than 7 microns fraction size, as a critical fraction, SiO2 content decreased from 4.45 per cent to 2.35 per cent. HPGR tests were performed on 8 per cent moisture in 4 N/mm2 specific force and according to the results after silica reduction HPGR operation conditions are optimised. Results showed that the working gap increased from 7 to 10.5 mm and specific throughput of material raised from 180 ts/hm3 to 250 ts/hm3 , and SSA increased by 300 cm2 /gr in a single pass.

Aug 24, 2022

By A Jyoti, J R. Black, R R. Haese, E O. Ansah

Copper (Cu) is a critical metal in the transition to a low-carbon power supply. Presently, low-grade copper sulfide ores account for almost 80 per cent of the global reserves. Large amounts of water are required to process these low-grade copper ores. The mining industry utilises lixiviants from recycled water from different sources to conserve water, whilst enhancing Cu recovery. Some utilise intermediate to pregnant leach solutions, sea water, and processed water from electrowinning circuits with highly variable concentrations of ions. Previous studies have highlighted the formation of precipitates that passivate the surfaces of minerals in these low-grade copper ores and/or block flow paths for lixiviant during heap leaching. In this study, we utilised concepts of phase replacement to devise an innovative means of controlling precipitation and increasing copper recovery using industrial brine as opposed to freshwater. We propose the formation of Al-rich phases (such as AlSO4 + or alunite) to replace iron sulfate and iron hydroxysulfates (such as jarosite) during the chalcopyrite dissolution-precipitation mechanism. The rationale is to have available Fe3+ throughout the chalcopyrite leaching process. We tested this method by carrying out various batch experiments using CaCl2, AlCl3, and NaCl industrial brine types compared to freshwater and explored the capacity to leach Cu from chalcopyrite. There is higher Cu recovery during oxidative leaching of chalcopyrite in industrial brine with 91 per cent recovery using AlCl3-rich brine, 84 per cent with NaCl-rich brine, and 56 per cent with CaCl2-rich brine as compared to 35 per cent recovery using freshwater. In the absence of Al3+, various forms of iron sulfates, and jarosite are formed, reducing the availability of Fe3+ for chalcopyrite dissolution. The introduction of Al3+ leads to the formation of AlSO4 + species, thus lowering sulfate activity and the tendency for K-jarosite formation.

Aug 24, 2022

By A Yáñez, P Vallejos, R Grau, J Yianatos

In flotation cells, especially in large flotation units, froth management is a crucial variable that should be considered during the design phase or optimised to improve the performance of existing flotation circuits. This paper presents a simulation evaluation of the effect of launder design on the metallurgical performance of an industrial flotation circuit consisting of five TankCell® e630 (630 m3 ) cells in a Cu rougher duty. This analysis was carried out using a new industrial simulator, which was built on a wide database collected from many industrial concentrators. This tool is currently incorporated into HSC Chemistry® software and allows evaluation of the effect of launder design on mineral froth recovery, water recovery, entrainment, and other variables to be quantified. The industrial flotation circuit was evaluated under different launder design scenarios, considering an actual flotation circuit that includes TankCell® e630 cells for calibration and as a reference (baseline). Firstly, two different designs were evaluated in the full circuit: a standard launder design and a new launder technology. It was found that the new launder technology enabled improvement of the mineral recovery along the circuit, mainly for coarse particles, due to the improvement in froth mineral recovery. Next, the partial upgrade of the launder design along the circuit was analysed. Thus, the new launder technology was evaluated in the first and the last two cells of the bank. The results showed that upgrading the launders in different cells along the circuit delivered an increase in the final recovery with respect to the baseline, with a partial impact on the concentrate grade. However, these changes are less than those when evaluating the full upgrade scenario. A partial launder upgrade either in the first or last two cells of the bank showed similar final recoveries, but the latter enabled a slightly higher concentrate grade (about 1 per cent higher) to be achieved. Finally, the evaluation of launder design using the industrial simulator made it possible to estimate its effect on variables that are not commonly obtained from plant surveys, including froth recovery per particle size, collection recovery per particle size and liberation, gangue entrainment and bubble loading grade.

Aug 24, 2022

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By G R. Ballantyne, G Lane

Dry milling circuits that include high pressure grinding rolls (HPGR) or vertical roller mills (VRM) and air classification have replaced dry ball milling in cement production, but how do they compare to wet milling and classification circuits in mineral processing plants? Two case studies are presented that compare the energy efficiency, wear, liberation and capital cost of dry and wet milling circuits. In both case studies the VRM and HPGR consume half the energy of a wet tumbling mill for the same duty. However, the dry classification system tends to significantly erode the energy benefits. A number of improvement opportunities are presented that have the potential to improve the energy and capital efficiency of dry milling circuits. These improvement opportunities focus on the dry classification system that consumes significant energy in heating and fan power requirements and requires a large proportion of the footprint.

Aug 24, 2022

By G Bournival, Y Pan, S Ata

A custom-made set-up that measures bubble coalescence time and the thin film balance (TFB) technique were used to explore the role of residual xanthate (potassium amyl xanthate, PAX) and salt (NaCl) on the adsorption of two frothers (methyl isobutyl carbinol-MIBC, and di-propylene glycolDPG) at the air-water interface. This paper is primarily focused on the comparison of these two techniques in studying the interaction between the flotation reagents and salt emphasizing their capabilities and limits. The results from the coalescence rig showed that the presence of PAX improved the stability of bubbles in both frother solutions and led to a bubble coalescence inhibition at 50–500 ppm DPG. These measures were compared with the results from the TFB. Findings from the TFB were overall in good agreement with the bubble coalescence time, but a higher stability level was observed in thin films under the same condition. The effect of salt on the frother and PAX mixture was also explored, and the results showed an adverse impact of the salt on the interaction of frother and PAX with both techniques. However, variations were found between them in some cases. The TFB is much more sensitive to the presence of dissolved gas and oil droplets.

Aug 24, 2022

By X Zhang, Y Zhu, P E. Ngoepe, P P. Mkhonto, W Xiong, L Han, L Lu

The triazine molecules have not been given much attention and they are potential collectors that may positively impact the mineral processing industry. The adsorption of triazine as collectors such as sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT) on pyrite form a basis in design of flotation collectors that may be applicable in a wide range of sulfide minerals. The SDTBAT collector was compared with the sodium normal butyl xanthate (SNBX) and sodium normal butyl dithiocarbamate (SNBDTC). All collectors were adsorbed in their neutral form containing sodium on the pyrite (100) surface. The computational calculations found that the adsorption energies followed the order: SDTBAT (-300.35 kJ/mol) > SNBX (-186.10 kJ/mol) > SNBDTC (-163.78 kJ/mol). It was observed that the SNBX and SNBDTC adsorbed through the S atoms, while the SDTBAT adsorbed through the S atoms and N atoms onto Fe atoms. It is clear that the SDTBAT had a strong binding energy which is attributed to the presence of the triazine group that is electron depositing to the active S atoms compared to the SNBX which possessed the oxygen that is electron withdrawing. Moreover, the SDTBAT collector was found to bind stronger than the xanthate. This was complimented by microflotation tests that showed fast floating and higher recoveries of pyrite when using the SDTBAT collector than the xanthate and DTC. This clearly demonstrated that the SDTBAT is a potential collector to replace the xanthate collector due to its high selectivity and flotation power.

Aug 24, 2022

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

This research was done to reduce silica from mixed hematite concentrate of Barfkar Iron Ore Sample and increase Fe grade using reverse flotation method (Depressing Hematite and floating Silica). The used sample in the reverse flotation tests was a mixture containing two types of hematite concentrates (Spiral cleaner concentrate and Slon-VPHGMS cleaner concentrate) with the percentage of 16 per cent and 84 per cent, respectively. Fe grade of two samples was 59.31 per cent and 57.52 per cent and SiO2 grade was 5.83 per cent and 6.71 per cent, respectively. After mixing, the Fe and SiO2 grade of the mixed sample was measured at 58.10 per cent and 6.20 per cent. For flotation tests, effect of variable operational parameters including feed size distribution (d80 = 130 microns and d80 = 53 microns), pulp solidity (25 per cent and 30 per cent w/w), pH (9.70, 10.20 and 11), Sodium silicate as a dispersant (500, 1000 and 2000 g/ton), Starch as a depressant (500, 1000, 2000 and 3000 g/ton) and EDA as a collector (180, 300, 400 and 500 g/ton) were investigated. For evaluating the influence of Sodium silicate and Starch dosage, initial flotation tests were performed on the main sample (d80 = 130 microns). These two parameters had no significant effects on the yield, Fe, and SiO2 grade of flotation concentrate based on test results. In the next step, screen analysis was carried out on the main sample for mineralogical studies. Accordingly, the suitable size distribution for releasing Fe and SiO2 particles was smaller than 53 microns. Therefore, the sample was crushed until d80 = 53 microns. Then, supplementary tests were performed on the crushed sample for studying the pH range, pulp solidity, and EDA collector dosage. After doing silica removal flotation tests based on the designed pattern and comparison of the results, the conditions consisting of size distribution d80 = 53 microns, pulp solidity 25 per cent, pH 10.20, Sodium silicate 1000 g/ton, Starch 1000 g/ton, and EDA 500 g/ton was selected as optimum values. In the last test, Fe and SiO2 grade was measured at 60.00 per cent and 3.93 per cent, respectively, and Fe recovery was obtained at 74.93 per cent.

Aug 24, 2022