Search Documents

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

By A. N. Holden, W. E. Seymour

DURING the last several years, the U-Zr system has been studied at many laboratories as one of the research programs sponsored by the Atomic Energy Commission. The equilibria in part of this system have been difficult to determine, although the phase diagram from 0 to 60 atomic pct Zr has been established with reasonable certainty. Existing diagrams of the system vary appreciably beyond 60 atomic pct Zr, particularly with regard to the existence of an intermediate phase. Most existing diagrams show a transformation or reaction horizontal near 600°C. In 1955, a collection of uranium phase diagrams' was prepared at the Battelle Memorial Institute and the U-Zr diagram in that collection contained a questionable region in the vicinity of 60 to 80 atomic pct Zr. Summer-Smith" has published a phase diagram of the system that shows no intermediate phase. Summer-Smith did his work with powders and found only the uranium and zirconium eutectoid mixture from X-ray patterns of material annealed below 600°C. Mueller3 at Argonne National Laboratory did similar work with filings, and he found that initially there was a pattern of an intermediate phase, but on long-time annealing

Jan 1, 1957

Characteristics Analysis of a Bastnaesite Rare Earth Mineral for Recovery of Cerium

Sep 13, 2010

By Mark P. Meyer

A mineral investigation of the Chugach National Forest, Alaska was conducted jointly by the U.S. Geological Survey and the U.S. Bureau of Mines from 1979 to 1983 as part of the RARE II program. The U. S. Geological Survey remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. Previously unreported mineralization in three areas, Long Bay, Wells Bay, and Miners River were discovered in the western portion of the SOUND study area. Copper, lead, zinc, gold, silver, nickel, cobalt, fluorite, and arsenic were found in north-northeast to north-northwest trending shear zones, veins, felsic dikes, and granitic intrusives in Tertiary Orca Group metasedimentary rocks.

Jan 1, 2011

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By G. Bacon

The past decade has witnessed unprecedented growth in the development and implementation of solvent extraction technology in the extractive metallurgy of nickel and cobalt. Solvent extraction is proving to be a powerful tool, opening new opportunities for simpler, more cost efficient and environmentally sound metal refining processes. These advances, however, could not have been possible without the cooperative efforts between the nickel industry and the people and organizations involved with reagents, materials and equipment development and supply as well as solvent extraction research, aided by the accumulated knowledge and practical experience from the copper and uranium solvent extraction operations. This paper provides an overview of these developments and some of the challenges ahead.

Jan 1, 2002

By Ian Misich

A research programme has been undertaken to evaluate and predict the effect of total extraction of coal by underground methods on the superimposed strata, aquifer systems and ground surface in the Collie Basin. Western Australia. The research work has integrated comprehensive field monitoring of surface and subsurface subsidence with empirical, analytical and physical modelling in an effort to develop an effective predictive tool which can be used in all mining scenarios. Early results indicate that although each method has certain limitations, this approach has enabled the researchers to develop a very good understanding of the subsidence mechanisms from the mine panel through to the surface in the weak, water saturated sediments in the Collie Basin. Given that both subsurface and surface subsidence characteristics have tied in well, greater confidence can be held for predictions made by representative models.

Jan 1, 1993

By Ralph D. Gift

This report describes a program of research to evaluate methanometry in coal mines. The program commenced by conducting an extensive state-of-the-art survey. Details of the survey are presented which includes a rating of various types of instruments that can be used to detect and record methane gas. Laboratory test data, on mine instruments tested are presented together with results from a computerized statistical analysts.

Jan 1, 1972

By N Guresin, A Cooper, L Lorenzen, H Muller, S C. Dominy

Sampling and metallurgical test work during various phases of engineering?studies?is of?paramount importance for a robust processing plant design. When developing a process flow sheet, risks in achieving desirable financial outcomes are minimised by ensuring appropriate sampling and adequate metallurgical test work supports the engineering and cost estimation at each phase of project development.The quality and type of samples used for metallurgical test work are just as important as the metallurgical test work itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should take into account the spatial orientation, lithology, alteration, degree of oxidation, mineralogy and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical test work program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design.Snowden has observed that the quality of sampling and quantity of metallurgical test work carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are often the result of the plant design based on benchmarks of apparently similar orebodies or buoyant metal prices supporting cash flows until rectifications can be implemented.The paper will discuss important aspects of sampling and test work required for engineering studies in designing process plants based on industrial case studies.CITATION:Guresin, N, Lorenzen, L, Dominy, S C, Muller, H and Cooper, A, 2012. Importance of effective sampling and test work protocols for process plant design, in Proceedings Sampling 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Paul M. Tyler

A great variety of substance that differ widely in chemical, mineralogical, and physical properties are loosely linked under the generic term "clay", but for the average man all that matters is whether a given material can be sold or used profitably. So-called "clays" range in texture from true clays and allied minerals that are typically "fat" or sticky to fine sand. Sand and other strictly silicious materials, such as tripoli and diatomite, are not clays in any sense; but many commercial clays are strictly loams, for they are intermediate in texture and always contain a mixture of minerals, though the term "loam" has little commercial usage except in foundry work. Even pure kaolinite, ordinarily considered the typical "clay substance", recently was found to exist as three distinct minerals; and each of these, in turn, exhibits variations in particle size and other physical attributes. Probing with the X-ray and employing other modern tools and techniques, scientists are tracing the patterns of molecules and finding chemical and physical phenomena that seem to disclose the causes for the markedly different behavior of the various aluminum silicates with varying proportions of combined and adsorbed water that are the essential ingredients of commercial clays; but rule-of-thumb definitions and enforced reliance upon empirical tests of actual samples still hold sway. In addition to the hydrated simple silicates of aluminum, almost all clays contain quartz, feldspar, and mica with varying amounts of organic matter and, in addition, other impurities - such as iron, manganese, and titanium oxides - that may discolor them sufficiently to render them unfit for certain important uses. The white clays are generally the purest, but no two clays are really alike, and great care must be exercised to maintain a reasonable uniformity in successive shipments even from the same deposit.

Jan 1, 1938

By R. N. Gow

The presence of enargite (Cu3AsS4) is problematic in gold processing because it is environmentally hazardous due to its arsenic content but also because it is double refractory causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte, Montana and Quiruvilca, Peru were spectroelectrochemically studied under alkaline conditions, pH range of 8-13, using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after voltammograms were potentially cycled in order to determine and compare surface species against theoretical EH-pH diagrams determined from mass-balanced thermodynamic calculations using StabCal software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of sulfur suggests that copper was eventually leached. By operating above pH 12, under slightly reducing conditions near -300mV vs SHE, arsenic can be selectively leached as thioarsenate (AsS43-) or thiosulfate (AsO43-) without sulfur formation.

Feb 27, 2013

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

By T G. Neville, G Terrey, J Burns

This paper explores recent industry training programs and lessons for supervisors. The Belbin Team Role model was used to increase participants’ awareness of behaviour and its application. The application of the Belbin model to underground, open cut mine and quarry supervisors is discussed.The key to team success may rest with the expertise and experience of its members, but increasingly effectiveness depends on how team members understand, acknowledge and support each other’s behavioural strengths. Discovering strengths is a challenge, both for their measurement and for the encouragement of team members to use the knowledge of themselves and others in the team. Using behavioural models provides a constructive approach and a language for supervisors as they build personal motivation and engagement.Prima facie, the mineral industry’s work may be too vigorous for teams and their managers could be more prone to use ‘solo’ or traditional management styles. Managers and supervisors must know when work allocated to a team is appropriate or where individual effort should be applauded and rewarded. For practical people with well-developed technical skills, improving the soft skills necessary for a supervisor requires some reflection and effort. The Belbin behavioural model can be an effective tool for recognising characteristics that can assist teams to be more productive.Experiencing the Belbin Team Role model as part of an industry qualification is important for supervisors studying to refine their team leadership skills. Data are available for participants to assess the nature of their teams and to confront the appropriateness of the behavioural mix for the work of the team and its individual members.So what are the next steps? All team development must have a place in the strategic thinking and plans of the enterprise. This needs a visible presence of senior managers and supervisors in managing a team culture with practical links to workplace priorities and professional development with continuous improvement.CITATION:Burns, J, Terrey, G and Neville, T G, 2016. Supervisors and teams at work, in Proceedings International Mine Management Conference, pp 125-138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Kim B. Shedd

The U.S. Bureau of Mines Particulate Mineralogy Unit examined the habits of six zeolite minerals commonly occurring in domestic zeolite deposits. Mineral habit is of interest because current theory on the potential for sarcoma production in test animals emphasizes the size and shape of mineral particles, without regard to composition or structure. A scanning electron microscopic study revealed that, of these six minerals, only mordenite and erionite crystallized in acicular to fibrous habits, The fibrous varieties of these two minerals were characterized by size and shape on the transmission electron microscope, and their dimensions were compared with those of asbestos and amphibole cleavage fragments. When comminuted, these two minerals possess "fibrosity indices" similar to those of amphibole cleavage fragments. One sample, a rare woolly erionite, has uniform widths, large aspect ratios, and a "fibrosity index" similar to those of asbestos.

Jan 1, 1982

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.

Jan 1, 1963

By Douglas Bartley, Jay Elkin

The state of Pennsylvania was at one time one of the leading coal producing states in the east. However, legislation and industry trends over the last 10 years have adversely affected the amount of bituminous coal mined in Pennsylvania and the whole eastern United States. The application for and approval of a new mining permit is a very costly and arduous task. When a new mining operation is established it is crucial that nothing within the operator’s control causes the operation to stop producing. This paper discusses the action taken by a small mine in Pennsylvania when their blast induced vibrations rose to levels that typically would have resulted in a total mine shut down by the regulatory body governing such operations.

Jan 1, 2003

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997