Search Documents

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By J. Sammarco

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to determine if light-emitting diode (LED) cap lamps can improve safety by reducing glare. Glare can impede a miner?s ability to see hazards and to safely perform their work. Another objective is to determine if a person?s age is a factor. This is important because the workforce is aging ? the average miner is now about 43 years old. Three cap lamps were used to evaluate glare: an incandescent cap lamp, a commercially available LED cap lamp and a NIOSH prototype LED cap lamp. Thirty NIOSH personnel from the Pittsburgh Research Laboratory (PRL) served as test subjects. Three age groups were established with ten subjects in each group. Testing was conducted in the Mine Illumination Laboratory (MIL) of NIOSH PRL. The results indicate no statistically significant difference in discomfort glare among the incandescent and LED cap lamps. However, an analysis of variance for disability glare indicates that the LED cap lamps were superior for the older subjects. Disability glare scores for the oldest subject group improved 53.8% when using the NIOSH prototype LED cap lamp compared to the incandescent cap lamp and 36.5% compared to the commercial LED cap lamp. It ap­pears that, given the conditions of this study, LED cap lamps will not increase discomfort glare and can enable significant improvements in disability glare for older workers. It is also evident that not all LEDs are created equal. The disability glare improved the best for older workers when they used the NIOSH prototype LED cap lamp, which has a different spectral power distribution (SPD) (more short wavelength energy) than the commercial LED cap lamp. Therefore, for disability glare, the results suggest that the SPD is an important factor to consider in cap lamp design.

Jan 1, 2009

By Frederick Bradley Henderson

This study was initiated to investigate the occurrence of cinnabar in the oxidation zones of some mercury sulfide deposits. Seven mines or mine districts were visited and samples were taken from both the oxidation and primary zones of these deposits in order to compare their mineralogies and assess Vie chemical changes that took place during oxidation. As a result of the study of these specimens, several limiting factors are suggested for the chemical environments and processes active in both the deposition and oxidation of mercury sulfide deposits. The Mt. Jackson mine, near Guerneville, California (location map, fig. 1), was studied in some detail and forms the basis of this paper. The mine has not heretofore been described in detail in the literature. The Mt. Jackson mine is considered typical of mercury sulfide deposits occurring at the faulted boundaries of serpentinite bodies and enclosing sediments. Such mines are common in the California and Oregon Coast Ranges? Specimens collected by the author from the New Idria and New Almaden districts, the Mt. Diablo, the Culver Bear, and the Buena Vista mines in California, and the Opalite district (Cordero and Bretz, mines) on the Oregon-Nevada border were studied for comparison with the Mt. Jackson samples. The mine description, maps and sketches were composed from field maps kindly provided by Francis Fredericks, consulting geologist to the Sonoma Quick-silver Mine Inc. during the author's visit in 1962. Additional information was obtained from the company maps and minor corrections and interpretations were added by the author.

Jan 1, 1965

By Gary L. Stecklein

This final report delineates the findings of the test programs, simulations, and analyses performed to determine the requirements for the effective application of berms and guardrails as truck restraint systems for elevated mine roadways. Included arts criterion for effective vehicle restraint for guardrail applications and recommendations for berm applications based on scale model tests and computer simulations. Full scale haulage vehicle-berm interaction field tests were performed to correlate the results of these model tests and computer simulations. Recommendations for the construction of berms were made on the basis of tests of berm bearing strength, response of the vehicle to different berms, and predictions based on the obtained correlation

Jan 1, 1981

By F. Dingwu

The latest technology and novel equipments in kaolin processing industry in China are described in this paper. Some typical experimental results are presented, which include laboratory-, pilot-or commercial-scale tests. The characteristics of kaolin processing technology are summarized, and the developing trends are indicated.

Jan 1, 1995

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.5

Jan 1, 1963

By Ramdane Bahar

"Abstract The design foundations can be performed using Menard pressuremeter rules that require a limit pressure and a pressuremeter modulus. In recent years, another trend of interpretation of this test is appeared. It consists of identifying the rheological soil parameters using analytical or numerical methods and then used to evaluate the bearing capacity and settlement of soil foundations using numerical software. This paper deals with the bearing capacity and settlement predictions of bored piles using two approaches. The first one is the method called ""Pressident"" which is a numerical program developed to analyse pressuremeter tests taking into account the Duncan and Chang model. The second approach is the method developed by Bahar and Olivari based on the generalised elastoplastic Prager’s model with the Von Mises criterion which is suitable to describe the behaviour of saturated clays under undrained conditions. The pressuremeter data, collected on various research and consulting projects are used to explore the relationship between limit pressure and undrained shear strength obtained by the two methods. Numerical calculations, by FLAC2D software taking into account the rheological parameters derived from these two methods, are performed in order to predict the behaviour of a single bored pile subjected to an axial vertical load. The predictions are comparedto the measured data.IntroductionThe Menard Pressuremeter test has been used extensively to measure in situ soil properties and for the design deep foundations in Algeria. These tests are an useful and economical way for obtaining reliable in situ properties of soils and provide the measurement of in situ stress-strain response of soils. From this test, the design foundations can be performed using pressuremeter rules that require a limit pressure, pl, and a pressuremeter modulus, EM. These two parameters are derived from the pressuremeter curve or deduced from existing correlations with undrained cohesion and internal angle friction (Ménard, 1957; Amar and Jézéquel, 1972), and are used to evaluate the bearing capacity of soil foundations and the expected settlements. But, they can also help to identify usual soil parameters required by simple constitutive models for soils in numerical calculations."

Jan 1, 2014

By Jan Krason

Introduction The South African Witwatersrand is the world's largest gold-bearing province and gold producing district. But the production capacity of the very big mines (Vaal Reef, Driefontein Cons., Western Holdings, Western Deep Levels, and others) is not as large as that of the Soviet Union's Muruntau gold mine. The Muruntau gold-bearing ore body was discovered in 1956-57, and has been in operation since that time. In the early 1970s, this mine produced 70 to 80 t/a (2.3 to 2.6 million oz per year) of gold. Within the last few years it has become the world's largest producing gold mine. Russian authors do not publish ore reserve or rate of production data. But it is very likely that the Muruntau mining complex, which involves several ore bodies, is currently producing about 143 t/a (4.6 million oz per year) of gold. The author has confirmed this by personal information from several knowledgeable Russian geologists. This amounts to one-half of

Jan 11, 1984

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

In this project, low grade copper ore samples were obtained from two mining sites in the US, and they were chalcopyrite-rich (sample A) and conichalcite-rich (sample B) ore. Copper grades were 0.6% and 0.4% for the two samples, A and B, respectively. Leaching experiments were conducted by bottle roll tests for 24 hours, and various lixiviant systems were applied. Methanesulfonic acid (MSA) and glycine were used as alternative lixiviants to sulfuric acid. Oxidants including ferric ion and hydrogen peroxide were tested. The results showed the copper extraction of sample A increased after adding 1 g/L ferric ion in sulfuric acid and MSA solution, from 20% to 36%, but further increase was not observed with higher ferric ion concentration. The copper recovery increased significantly with H2O2 concentration, and over 80% copper recovery was obtained with 10% H2O2. For sample B, the copper dissolution kinetics were relatively fast and reached the maximum value in five hours. Around 60% copper were extracted in sulfuric acid and MSA solution. Copper recovery slightly increased after adding ferric ion and H2O2. Glycine is a weaker lixiviant for both samples, the copper extractions were 36% and 4% respectively. INTRODUCTION Chalcopyrite is the most abundant copper sulfide mineral on earth, and it is one of the most refractory copper minerals regarding chemical processing. The declining copper grade and depletion of copper oxide deposits stimulate the development of hydrometallurgical process to extract copper from chalcopyrite. The dissolution of chalcopyrite by ferric ion is normally illustrated as Equation (1) and (2) (Dutrizac & MacDonald, 1974): CuFeS2 + 4Fe3+ → Cu2+ + 5Fe2+ + 2S0 (1) CuFeS2 + 4Fe3+ + 3O2 + 2H2O → Cu2+ + 5Fe2+ + 2H2SO4 (2) However, slow kinetics are usually observed from chalcopyrite leaching at ambient temperature and pressure. Researchers attribute the slow kinetics to passivation during chalcopyrite dissolution, and different passivation products are also proposed (Klauber, 2008). In recent years, many efforts have made to develop new methods to extract copper from chalcopyrite, such as utilizing bacteria or stronger oxidant (Zhao et al., 2015; Ruiz-Sánchez & Lapidus, 2017).

Jan 1, 2019

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011

By S. Lolon

Spontaneous combustion in underground coal mines has become a serious problem particularly in the caved area (gob). Recent statistic has shown that approximately 17% of total 87 underground coal mine fires in the United States are attributed to spontaneous combustion (De Rosa, 2004). Spontaneous combustion results from a self-heating process in exothermic conditions. The accumulated heat, if not removed, is conducive to the rapid increase of temperature and may result in mine fires or explosions. It is well accepted that the interaction between oxygen and coal substances is the main cause for spontaneous combustion, while other factors such as pyrite, moisture, and bacteria play a secondary role to the self-heating of coal. Therefore, only coal oxidation is considered in this study. Coal oxidation occurs as coal comes into contact with air. This process involves complex phenomena in terms of heat transfer, chemical surface absorption, and energy balance related to inherent properties of coal (Wang et al., 2003). For simulation purpose, overall reactions can be simplified as suggested by Mitchell (1990): C + O2 CO2 + heat [65°- 94°C] (1) CO2 + C 2CO + heat [100°- 150°C] (2) Stoichiometric reactions (1) and (2) show that 2.66 grams of oxygen are required to oxidize 1.0 gram of carbon. Once the temperature exceeds 100°C, the reaction has little chance to stop. The crucial step in reducing spontaneous combustion risk is locating the ignition point of spontaneous combustion (hot spot). This information is useful in the effort of developing a preventive method effectively. In this study, this was conducted based on the best gathered information: ventilation surveys conducted in an existing longwall mine located in the western US; the laboratory experiments performed on a physical gob model; and the CFD models to investigate the flow behavior in the gob, the oxidation of coal, and heat transfer phenomena. The hot spot location is determined as a function of oxygen concentration and gob temperature. The critical values are the following: 5% (by volume) for oxygen and 100°C for gob temperature. CHARACTERISTICS OF GOB MATERIAL AND MODELS Permeability Concept Permeability is one of the key parameters in any study dealing with porous medium. This is determined by particle size and the ratio of void volume to the total volume (porosity) of porous medium. This relationship is known as the Carman-Kozeny equation (Scheidegger, 1957) and is given mathematically as [ ] where k* = theoretical specific permeability, m2 dm = the mean particle size, m n = porosity However, permeability tests with various particle sizes were carried out at the University of Utah?s ventilation model (Figure 1) to verify this relationship. These tests indicated a necessity to modify this theoretical relationship. A factor of 0.898 was obtained to make up the different between theoretical permeability and the experimental one. The modified version of (3) is given by: [ ] This equation is used to determine permeability of the simulated mine gob throughout the study. [ ] Mine Gob Material The gob is represented by zones filled with material of given size distribution. For physical measurements and CFD simulations, the material used were crushed rock and coal. Due to compaction, three different characteristics of gob material were used in the model: unconsolidated, semiconsolidated, and consolidated. In the real condition, the largest coal-rock particles are more likely to be located in the area behind the shields. This material is freshly broken and unconsolidated. The size of these broken particles is based on a study carried out by analyzing images taken from the area behind the shields in three coal mines in the United States (Pappas and Mark, 1993). The results have shown that the mean size of materials behind the shields is about 1.22 m. The permeability associated with this size was then obtained from (4) and permeability tests. This was 4.68 x10-7 m2. For semiconsolidated and consolidated zones, due to the lack of experimental data, these were determined through CFD simulations. These simulations were designed by assigning a permeability of 3.15 x 10-8 m2 for consolidated zone and 7.98 x 10-9 m2 to the other zone. The airflow pattern in the gob assigned with given permeabilities was expected to follow the experimental distribution (Brunner, 1985). The mean particle sizes for the semi-consolidated and consolidated zones were 0.02 and 0.006 m, respectively; smaller than those of the unconsolidated zone. Figure 2 shows the 3D view of permeability changes in the gob.

Jan 1, 2009

By S Love, M Anderson, M Boland

"The high rate of failure of new mine developments to meet feasibility study expectations has been the subject of many fine technical papers. Yet failure rates remain stubbornly high.Similarly, the common occurrence of disastrous acquisitions resulting from failed due diligence on projects is well known. Yet such mistakes continue to be made.The authors argue that project and due diligence failure are caused at least partly by cognitive biases. These biases pervade decision-making throughout project evaluations.A wider understanding of these biases (and their effects) is necessary. Only then can mitigating actions be taken.The opportunity for this wider understanding exists. A number of best-selling books have been published on the topic in recent years. With wider understanding of key concepts and terms, cognitive biases can be recognised and discussed. They can also be challenged and mitigated.The authors believe that these concepts should be entry-level, required knowledge for anyone evaluating, developing, reviewing or financing mining projects.Perhaps the most prevalent biases in project evaluation failure are the ‘over-optimism’ biases. In particular, the planning fallacy and confirmation bias.The anchoring effect is also pervasive. This bias propagates unrealistic assumptions from scoping and prefeasibility studies through to so-called definitive feasibility studies. Unrecognised anchoring biases also undermine the validity of many ‘independent’ due diligence reviews. They are also prevalent in corporate acquisitions.The availability heuristic refers to a mental shortcut that can lead to a number of biases. One of these is the narrative fallacy. The mind constructs coherent narratives and opinions, regardless of the amount and quality of the information that support them. Narrative fallacy commonly occurs in the evaluation of social and political risk. Another is disaster neglect, which is especially common in the failure to assess risks associated with tailings management.This paper outlines the relevance of these biases to mine project evaluations. It also provides examples where the authors have observed their effects.CITATION:Love, S, Boland, M and Anderson, M, 2016. Influence of cognitive biases on project evaluation, in Proceedings Project Evaluation 2016, pp 226–235 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

By Terry J. Close

U.S. Bureau of Mines personnel studied the 33,900-acre Silver Peak Range North Wilderness Study Area (NV-060-338), in order to evaluate its identified mineral resources. The area studied lies between the towns of Silver Peak and Dyer, about 40 miles southwest of Tonopah, in Esmeralda County, Nevada. There are no producing mines in the area studied. However, development of Sunshine Mining Company?s Sixteen-to-One silver-gold mine, located in the Silver Peak mining district near the eastern edge of the study area in the early 19801s, has stimulated recent interest. The Sunshine Mining Company claimed two sites within the study area in 1985. Also, Intermountain Resources, Incorporated, located a group of claims at a prospect along the west side of the study area in the Dyer mining district, and in 1986, began drilling. Other claimants are holding two other claim groups by assessment. At the five currently (1987) held sites, precious metals occurrences are being investigated. There are no patented mining claims or mineral leases in the study area.

Jan 1, 1987

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By A M. Sherwood

The Otago and Southland lignite deposits represent by far the largest known fossil energy resources in New Zealand. Despite their size they have remained virtually untouched since exploration in the 1970s and 1980s defined their extent. In total there is an estimated 10.9 billion tonnes of lignite in 13 defined fields in Otago and Southland. Much of the exploration work only targeted seams at shallow depth and it is highly probable that there are further resources at depth in the fields that have been explored to date.   L&M Lignite Limited (L&M) holds exploration permits over a number of lignite deposits and is currently engaged in pre-feasibility studies to investigate the potential of the lignites for gasification. L&M is focussing its studies on the Hawkdun and Ashers-Waituna deposits. Coal quality in these deposits, particularly Ashers-Waituna, is highly suitable for gasification. In total the two deposits contain 1647 Mt of potentially recoverable lignite. L&M has engaged a variety of consultants to progress this project. The Hawkdun and Ashers-Waituna deposit databases have been re-evaluated and the resources remodelled. Further drilling has been carried out and the coal quality database has been expanded. The baseline project is to develop a mine to feed a plant that will produce liquids, specifically low-sulphur diesel and naptha, using the Fischer-Tropsch process. The project anticipates a staged development of 10 000 barrel per day units, each requiring mining at the rate of 12 700 tonnes of lignite per day. The production of other products including ammonia-urea, methanol, hydrogen and electric power is also under study.

Jan 1, 2005

By Doris M. Hyde

Mineral output and trade in the Central American countries were directly or indirectly affected by the sometimes violent civil unrest and recessionary economic developments that have pervaded the region for several years. Central American countries found their foreign exchange export earnings and traditional market areas shrinking while essential import costs were rising. Restricted spending measures were adopted by governments and private industries. Domestic investment funds for mineral development and exploration projects were among the first casualties of these austere budgetary measures, especially since weak demand and depressed mineral prices diminished the probability of a favorable cost-benefit ratio. The lack of physical security and political stability also discouraged private foreign investment. The United States Congress enacted the Caribbean Basin Economic Recovery Act of 1983 (19 U.S.C. 2702), more popularly known as the Caribbean Basin Initiative (CBI). This legislation was designed to stimulate economic recovery and promote economic development by increasing private investment and trade in the Caribbean Basin countries. The act provided for the elimination of U.S. duties on most trade items imported directly from eligible Caribbean countries, provided at least 35% of the product value originated in the region. The financial assistance components of the CBI were to be supportive of the basin's private sector as well as assist general economic stabilization programs.

Jan 1, 1985

By M Lentz

This paper will discuss the issues associated with blasting in an urban mining environment that have been addressed by Winstone Aggregates at the Mt Wellington Quarry. These issues include - control of vibration and air overpressure, repeatability of shot performance, fragmentation on an extremely low maximum instantaneous charge, compliance with Territorial Authority regulations and perception. Over the last two years, in order to address these issues, Winstone Aggregates have undertaken a programme of continuous improvement, which has included; ò implementation of new technology; ò revising site procedures; ò conducting an investigation into the structural response of local buildings; ò investigating safe extrapolation; ò extensive public consultation; ò establishing credibility during the consent process; ò identification of perception issues; and ò building relationships and trust with neighbours. The issues addressed at the Mt Wellington Quarry have increasing significance for traditionally rural mining operations, as the input of the local community being urban or rural, increases. New and existing operations have the potential to adopt best practice now, building trust with the community and raising the profile of the industry.  

Jan 1, 1999